include/configs/MPC8560ADS.h

   1 /*
   2  * Copyright 2004, 2011 Freescale Semiconductor.
   3  * (C) Copyright 2002,2003 Motorola,Inc.
   4  * Xianghua Xiao <X.Xiao@motorola.com>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * mpc8560ads board configuration file
  11  *
  12  * Please refer to doc/README.mpc85xx for more info.
  13  *
  14  * Make sure you change the MAC address and other network params first,
  15  * search for CONFIG_SERVERIP, etc. in this file.
  16  */
  17
  18 #ifndef __CONFIG_H
  19 #define __CONFIG_H
  20
  21 /* High Level Configuration Options */
  22 #define CONFIG_BOOKE            1       /* BOOKE */
  23 #define CONFIG_E500             1       /* BOOKE e500 family */
  24 #define CONFIG_CPM2             1       /* has CPM2 */
  25 #define CONFIG_MPC8560ADS       1       /* MPC8560ADS board specific */
  26 #define CONFIG_MPC8560          1
  27
  28 /*
  29  * default CCARBAR is at 0xff700000
  30  * assume U-Boot is less than 0.5MB
  31  */
  32 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  33
  34 #define CONFIG_PCI
  35 #define CONFIG_PCI_INDIRECT_BRIDGE
  36 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  37 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
  38 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
  39 #define CONFIG_ENV_OVERWRITE
  40 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  41 #define CONFIG_RESET_PHY_R      1       /* Call reset_phy() */
  42
  43 /*
  44  * sysclk for MPC85xx
  45  *
  46  * Two valid values are:
  47  *    33000000
  48  *    66000000
  49  *
  50  * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
  51  * is likely the desired value here, so that is now the default.
  52  * The board, however, can run at 66MHz.  In any event, this value
  53  * must match the settings of some switches.  Details can be found
  54  * in the README.mpc85xxads.
  55  */
  56
  57 #ifndef CONFIG_SYS_CLK_FREQ
  58 #define CONFIG_SYS_CLK_FREQ     33000000
  59 #endif
  60
  61
  62 /*
  63  * These can be toggled for performance analysis, otherwise use default.
  64  */
  65 #define CONFIG_L2_CACHE                 /* toggle L2 cache */
  66 #define CONFIG_BTB                      /* toggle branch predition */
  67
  68 #define CONFIG_SYS_INIT_DBCR DBCR_IDM           /* Enable Debug Exceptions */
  69
  70 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  71 #define CONFIG_SYS_MEMTEST_END          0x00400000
  72
  73 #define CONFIG_SYS_CCSRBAR              0xe0000000
  74 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  75
  76 /* DDR Setup */
  77 #define CONFIG_SYS_FSL_DDR1
  78 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup*/
  79 #define CONFIG_DDR_SPD
  80 #undef CONFIG_FSL_DDR_INTERACTIVE
  81
  82 #define CONFIG_MEM_INIT_VALUE           0xDeadBeef
  83
  84 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  85 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  86
  87 #define CONFIG_NUM_DDR_CONTROLLERS      1
  88 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  89 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
  90
  91 /* I2C addresses of SPD EEPROMs */
  92 #define SPD_EEPROM_ADDRESS      0x51    /* CTLR 0 DIMM 0 */
  93
  94 /* These are used when DDR doesn't use SPD.  */
  95 #define CONFIG_SYS_SDRAM_SIZE   128             /* DDR is 128MB */
  96 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007      /* 0-128MB */
  97 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80000002
  98 #define CONFIG_SYS_DDR_TIMING_1 0x37344321
  99 #define CONFIG_SYS_DDR_TIMING_2 0x00000800      /* P9-45,may need tuning */
 100 #define CONFIG_SYS_DDR_CONTROL          0xc2000000      /* unbuffered,no DYN_PWR */
 101 #define CONFIG_SYS_DDR_MODE             0x00000062      /* DLL,normal,seq,4/2.5 */
 102 #define CONFIG_SYS_DDR_INTERVAL 0x05200100      /* autocharge,no open page */
 103
 104 /*
 105  * SDRAM on the Local Bus
 106  */
 107 #define CONFIG_SYS_LBC_SDRAM_BASE       0xf0000000      /* Localbus SDRAM */
 108 #define CONFIG_SYS_LBC_SDRAM_SIZE       64              /* LBC SDRAM is 64MB */
 109
 110 #define CONFIG_SYS_FLASH_BASE           0xff000000      /* start of FLASH 16M */
 111 #define CONFIG_SYS_BR0_PRELIM           0xff001801      /* port size 32bit */
 112
 113 #define CONFIG_SYS_OR0_PRELIM           0xff006ff7      /* 16MB Flash */
 114 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 115 #define CONFIG_SYS_MAX_FLASH_SECT       64              /* sectors per device */
 116 #undef  CONFIG_SYS_FLASH_CHECKSUM
 117 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 118 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 119
 120 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 121
 122 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 123 #define CONFIG_SYS_RAMBOOT
 124 #else
 125 #undef  CONFIG_SYS_RAMBOOT
 126 #endif
 127
 128 #define CONFIG_FLASH_CFI_DRIVER
 129 #define CONFIG_SYS_FLASH_CFI
 130 #define CONFIG_SYS_FLASH_EMPTY_INFO
 131
 132 #undef CONFIG_CLOCKS_IN_MHZ
 133
 134
 135 /*
 136  * Local Bus Definitions
 137  */
 138
 139 /*
 140  * Base Register 2 and Option Register 2 configure SDRAM.
 141  * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
 142  *
 143  * For BR2, need:
 144  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
 145  *    port-size = 32-bits = BR2[19:20] = 11
 146  *    no parity checking = BR2[21:22] = 00
 147  *    SDRAM for MSEL = BR2[24:26] = 011
 148  *    Valid = BR[31] = 1
 149  *
 150  * 0    4    8    12   16   20   24   28
 151  * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
 152  *
 153  * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
 154  * FIXME: the top 17 bits of BR2.
 155  */
 156
 157 #define CONFIG_SYS_BR2_PRELIM           0xf0001861
 158
 159 /*
 160  * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
 161  *
 162  * For OR2, need:
 163  *    64MB mask for AM, OR2[0:7] = 1111 1100
 164  *                 XAM, OR2[17:18] = 11
 165  *    9 columns OR2[19-21] = 010
 166  *    13 rows   OR2[23-25] = 100
 167  *    EAD set for extra time OR[31] = 1
 168  *
 169  * 0    4    8    12   16   20   24   28
 170  * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
 171  */
 172
 173 #define CONFIG_SYS_OR2_PRELIM           0xfc006901
 174
 175 #define CONFIG_SYS_LBC_LCRR             0x00030004    /* LB clock ratio reg */
 176 #define CONFIG_SYS_LBC_LBCR             0x00000000    /* LB config reg */
 177 #define CONFIG_SYS_LBC_LSRT             0x20000000    /* LB sdram refresh timer */
 178 #define CONFIG_SYS_LBC_MRTPR            0x20000000    /* LB refresh timer prescal*/
 179
 180 #define CONFIG_SYS_LBC_LSDMR_COMMON     ( LSDMR_BSMA1516        \
 181                                 | LSDMR_RFCR5           \
 182                                 | LSDMR_PRETOACT3       \
 183                                 | LSDMR_ACTTORW3        \
 184                                 | LSDMR_BL8             \
 185                                 | LSDMR_WRC2            \
 186                                 | LSDMR_CL3             \
 187                                 | LSDMR_RFEN            \
 188                                 )
 189
 190 /*
 191  * SDRAM Controller configuration sequence.
 192  */
 193 #define CONFIG_SYS_LBC_LSDMR_1  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL)
 194 #define CONFIG_SYS_LBC_LSDMR_2  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 195 #define CONFIG_SYS_LBC_LSDMR_3  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH)
 196 #define CONFIG_SYS_LBC_LSDMR_4  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 197 #define CONFIG_SYS_LBC_LSDMR_5  (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 198
 199
 200 /*
 201  * 32KB, 8-bit wide for ADS config reg
 202  */
 203 #define CONFIG_SYS_BR4_PRELIM          0xf8000801
 204 #define CONFIG_SYS_OR4_PRELIM           0xffffe1f1
 205 #define CONFIG_SYS_BCSR         (CONFIG_SYS_BR4_PRELIM & 0xffff8000)
 206
 207 #define CONFIG_SYS_INIT_RAM_LOCK        1
 208 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000      /* Initial RAM address */
 209 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */
 210
 211 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 212 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 213
 214 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB for Mon */
 215 #define CONFIG_SYS_MALLOC_LEN           (128 * 1024)    /* Reserved for malloc */
 216
 217 /* Serial Port */
 218 #define CONFIG_CONS_ON_SCC      /* define if console on SCC */
 219 #undef  CONFIG_CONS_NONE        /* define if console on something else */
 220 #define CONFIG_CONS_INDEX       1  /* which serial channel for console */
 221
 222 #define CONFIG_BAUDRATE         115200
 223
 224 #define CONFIG_SYS_BAUDRATE_TABLE  \
 225         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 226
 227 /* Use the HUSH parser */
 228 #define CONFIG_SYS_HUSH_PARSER
 229 #ifdef  CONFIG_SYS_HUSH_PARSER
 230 #endif
 231
 232 /* pass open firmware flat tree */
 233 #define CONFIG_OF_LIBFDT                1
 234 #define CONFIG_OF_BOARD_SETUP           1
 235 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 236
 237 /*
 238  * I2C
 239  */
 240 #define CONFIG_SYS_I2C
 241 #define CONFIG_SYS_I2C_FSL
 242 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 243 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 244 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 245 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 246
 247 /* RapidIO MMU */
 248 #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000      /* base address */
 249 #define CONFIG_SYS_RIO_MEM_BUS  0xc0000000      /* base address */
 250 #define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000
 251 #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000      /* 128M */
 252
 253 /*
 254  * General PCI
 255  * Memory space is mapped 1-1, but I/O space must start from 0.
 256  */
 257 #define CONFIG_SYS_PCI1_MEM_VIRT        0x80000000
 258 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
 259 #define CONFIG_SYS_PCI1_MEM_PHYS        0x80000000
 260 #define CONFIG_SYS_PCI1_MEM_SIZE        0x20000000      /* 512M */
 261 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
 262 #define CONFIG_SYS_PCI1_IO_BUS  0x00000000
 263 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
 264 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000        /* 1M */
 265
 266 #if defined(CONFIG_PCI)
 267
 268 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 269
 270 #undef CONFIG_EEPRO100
 271 #undef CONFIG_TULIP
 272
 273 #if !defined(CONFIG_PCI_PNP)
 274     #define PCI_ENET0_IOADDR    0xe0000000
 275     #define PCI_ENET0_MEMADDR   0xe0000000
 276     #define PCI_IDSEL_NUMBER    0x0c    /* slot0->3(IDSEL)=12->15 */
 277 #endif
 278
 279 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 280 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 281
 282 #endif  /* CONFIG_PCI */
 283
 284
 285 #ifdef CONFIG_TSEC_ENET
 286
 287 #ifndef CONFIG_MII
 288 #define CONFIG_MII              1       /* MII PHY management */
 289 #endif
 290 #define CONFIG_TSEC1    1
 291 #define CONFIG_TSEC1_NAME       "TSEC0"
 292 #define CONFIG_TSEC2    1
 293 #define CONFIG_TSEC2_NAME       "TSEC1"
 294 #define TSEC1_PHY_ADDR          0
 295 #define TSEC2_PHY_ADDR          1
 296 #define TSEC1_PHYIDX            0
 297 #define TSEC2_PHYIDX            0
 298 #define TSEC1_FLAGS             TSEC_GIGABIT
 299 #define TSEC2_FLAGS             TSEC_GIGABIT
 300
 301 /* Options are: TSEC[0-1] */
 302 #define CONFIG_ETHPRIME         "TSEC0"
 303
 304 #endif /* CONFIG_TSEC_ENET */
 305
 306 #ifdef CONFIG_ETHER_ON_FCC              /* CPM FCC Ethernet */
 307
 308 #undef  CONFIG_ETHER_NONE               /* define if ether on something else */
 309 #define CONFIG_ETHER_INDEX      2       /* which channel for ether */
 310
 311 #if (CONFIG_ETHER_INDEX == 2)
 312   /*
 313    * - Rx-CLK is CLK13
 314    * - Tx-CLK is CLK14
 315    * - Select bus for bd/buffers
 316    * - Full duplex
 317    */
 318   #define CONFIG_SYS_CMXFCR_MASK2      (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
 319   #define CONFIG_SYS_CMXFCR_VALUE2     (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
 320   #define CONFIG_SYS_CPMFCR_RAMTYPE    0
 321   #define CONFIG_SYS_FCC_PSMR          (FCC_PSMR_FDE)
 322   #define FETH2_RST             0x01
 323 #elif (CONFIG_ETHER_INDEX == 3)
 324   /* need more definitions here for FE3 */
 325   #define FETH3_RST             0x80
 326 #endif                                  /* CONFIG_ETHER_INDEX */
 327
 328 #ifndef CONFIG_MII
 329 #define CONFIG_MII              1       /* MII PHY management */
 330 #endif
 331
 332 #define CONFIG_BITBANGMII               /* bit-bang MII PHY management */
 333
 334 /*
 335  * GPIO pins used for bit-banged MII communications
 336  */
 337 #define MDIO_PORT       2               /* Port C */
 338 #define MDIO_DECLARE    volatile ioport_t *iop = ioport_addr ( \
 339                                 (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
 340 #define MDC_DECLARE     MDIO_DECLARE
 341
 342 #define MDIO_ACTIVE     (iop->pdir |=  0x00400000)
 343 #define MDIO_TRISTATE   (iop->pdir &= ~0x00400000)
 344 #define MDIO_READ       ((iop->pdat &  0x00400000) != 0)
 345
 346 #define MDIO(bit)       if(bit) iop->pdat |=  0x00400000; \
 347                         else    iop->pdat &= ~0x00400000
 348
 349 #define MDC(bit)        if(bit) iop->pdat |=  0x00200000; \
 350                         else    iop->pdat &= ~0x00200000
 351
 352 #define MIIDELAY        udelay(1)
 353
 354 #endif
 355
 356
 357 /*
 358  * Environment
 359  */
 360 #ifndef CONFIG_SYS_RAMBOOT
 361   #define CONFIG_ENV_IS_IN_FLASH        1
 362   #define CONFIG_ENV_ADDR               (CONFIG_SYS_MONITOR_BASE + 0x40000)
 363   #define CONFIG_ENV_SECT_SIZE  0x40000 /* 256K(one sector) for env */
 364   #define CONFIG_ENV_SIZE               0x2000
 365 #else
 366   #define CONFIG_SYS_NO_FLASH           1       /* Flash is not usable now */
 367   #define CONFIG_ENV_IS_NOWHERE 1       /* Store ENV in memory only */
 368   #define CONFIG_ENV_ADDR               (CONFIG_SYS_MONITOR_BASE - 0x1000)
 369   #define CONFIG_ENV_SIZE               0x2000
 370 #endif
 371
 372 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 373 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 374
 375 /*
 376  * BOOTP options
 377  */
 378 #define CONFIG_BOOTP_BOOTFILESIZE
 379 #define CONFIG_BOOTP_BOOTPATH
 380 #define CONFIG_BOOTP_GATEWAY
 381 #define CONFIG_BOOTP_HOSTNAME
 382
 383
 384 /*
 385  * Command line configuration.
 386  */
 387 #include <config_cmd_default.h>
 388
 389 #define CONFIG_CMD_PING
 390 #define CONFIG_CMD_I2C
 391 #define CONFIG_CMD_ELF
 392 #define CONFIG_CMD_IRQ
 393 #define CONFIG_CMD_SETEXPR
 394 #define CONFIG_CMD_REGINFO
 395
 396 #if defined(CONFIG_PCI)
 397     #define CONFIG_CMD_PCI
 398 #endif
 399
 400 #if defined(CONFIG_ETHER_ON_FCC)
 401     #define CONFIG_CMD_MII
 402 #endif
 403
 404 #if defined(CONFIG_SYS_RAMBOOT)
 405     #undef CONFIG_CMD_SAVEENV
 406     #undef CONFIG_CMD_LOADS
 407 #endif
 408
 409
 410 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 411
 412 /*
 413  * Miscellaneous configurable options
 414  */
 415 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 416 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 417 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 418 #define CONFIG_SYS_LOAD_ADDR    0x1000000       /* default load address */
 419
 420 #if defined(CONFIG_CMD_KGDB)
 421     #define CONFIG_SYS_CBSIZE   1024            /* Console I/O Buffer Size */
 422 #else
 423     #define CONFIG_SYS_CBSIZE   256             /* Console I/O Buffer Size */
 424 #endif
 425
 426 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 427 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 428 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 429
 430 /*
 431  * For booting Linux, the board info and command line data
 432  * have to be in the first 64 MB of memory, since this is
 433  * the maximum mapped by the Linux kernel during initialization.
 434  */
 435 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory map for Linux*/
 436 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 437
 438 #if defined(CONFIG_CMD_KGDB)
 439 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 440 #endif
 441
 442
 443 /*
 444  * Environment Configuration
 445  */
 446 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
 447 #define CONFIG_HAS_ETH0
 448 #define CONFIG_HAS_ETH1
 449 #define CONFIG_HAS_ETH2
 450 #define CONFIG_HAS_ETH3
 451 #endif
 452
 453 #define CONFIG_IPADDR    192.168.1.253
 454
 455 #define CONFIG_HOSTNAME         unknown
 456 #define CONFIG_ROOTPATH         "/nfsroot"
 457 #define CONFIG_BOOTFILE         "your.uImage"
 458
 459 #define CONFIG_SERVERIP  192.168.1.1
 460 #define CONFIG_GATEWAYIP 192.168.1.1
 461 #define CONFIG_NETMASK   255.255.255.0
 462
 463 #define CONFIG_LOADADDR  200000 /* default location for tftp and bootm */
 464
 465 #define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
 466 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 467
 468 #define CONFIG_BAUDRATE 115200
 469
 470 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 471         "netdev=eth0\0"                                                 \
 472         "consoledev=ttyCPM\0"                                           \
 473         "ramdiskaddr=1000000\0"                                         \
 474         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 475         "fdtaddr=400000\0"                                              \
 476         "fdtfile=mpc8560ads.dtb\0"
 477
 478 #define CONFIG_NFSBOOTCOMMAND                                           \
 479         "setenv bootargs root=/dev/nfs rw "                             \
 480                 "nfsroot=$serverip:$rootpath "                          \
 481                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 482                 "console=$consoledev,$baudrate $othbootargs;"           \
 483         "tftp $loadaddr $bootfile;"                                     \
 484         "tftp $fdtaddr $fdtfile;"                                       \
 485         "bootm $loadaddr - $fdtaddr"
 486
 487 #define CONFIG_RAMBOOTCOMMAND \
 488         "setenv bootargs root=/dev/ram rw "                             \
 489                 "console=$consoledev,$baudrate $othbootargs;"           \
 490         "tftp $ramdiskaddr $ramdiskfile;"                               \
 491         "tftp $loadaddr $bootfile;"                                     \
 492         "tftp $fdtaddr $fdtfile;"                                       \
 493         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 494
 495 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 496
 497 #endif  /* __CONFIG_H */