include/configs/MPC8568MDS.h

   1 /*
   2  * Copyright 2004-2007, 2010-2011 Freescale Semiconductor.
   3  *
   4  * See file CREDITS for list of people who contributed to this
   5  * project.
   6  *
   7  * This program is free software; you can redistribute it and/or
   8  * modify it under the terms of the GNU General Public License as
   9  * published by the Free Software Foundation; either version 2 of
  10  * the License, or (at your option) any later version.
  11  *
  12  * This program is distributed in the hope that it will be useful,
  13  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  14  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  15  * GNU General Public License for more details.
  16  *
  17  * You should have received a copy of the GNU General Public License
  18  * along with this program; if not, write to the Free Software
  19  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  20  * MA 02111-1307 USA
  21  */
  22
  23 /*
  24  * mpc8568mds board configuration file
  25  */
  26 #ifndef __CONFIG_H
  27 #define __CONFIG_H
  28
  29 /* High Level Configuration Options */
  30 #define CONFIG_BOOKE            1       /* BOOKE */
  31 #define CONFIG_E500             1       /* BOOKE e500 family */
  32 #define CONFIG_MPC85xx          1       /* MPC8540/60/55/41/48/68 */
  33 #define CONFIG_MPC8568          1       /* MPC8568 specific */
  34 #define CONFIG_MPC8568MDS       1       /* MPC8568MDS board specific */
  35
  36 #define CONFIG_SYS_TEXT_BASE    0xfff80000
  37
  38 #define CONFIG_SYS_SRIO
  39 #define CONFIG_SRIO1                    /* SRIO port 1 */
  40
  41 #define CONFIG_PCI              1       /* Enable PCI/PCIE */
  42 #define CONFIG_PCI1             1       /* PCI controller */
  43 #define CONFIG_PCIE1            1       /* PCIE controller */
  44 #define CONFIG_FSL_PCI_INIT     1       /* use common fsl pci init code */
  45 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  46 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  47 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  48 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
  49 #define CONFIG_QE                       /* Enable QE */
  50 #define CONFIG_ENV_OVERWRITE
  51 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  52
  53 #ifndef __ASSEMBLY__
  54 extern unsigned long get_clock_freq(void);
  55 #endif                                            /*Replace a call to get_clock_freq (after it is implemented)*/
  56 #define CONFIG_SYS_CLK_FREQ     66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */
  57
  58 /*
  59  * These can be toggled for performance analysis, otherwise use default.
  60  */
  61 #define CONFIG_L2_CACHE                         /* toggle L2 cache      */
  62 #define CONFIG_BTB                              /* toggle branch predition */
  63
  64 /*
  65  * Only possible on E500 Version 2 or newer cores.
  66  */
  67 #define CONFIG_ENABLE_36BIT_PHYS        1
  68
  69
  70 #define CONFIG_BOARD_EARLY_INIT_F       1       /* Call board_pre_init */
  71
  72 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
  73 #define CONFIG_SYS_MEMTEST_END          0x00400000
  74
  75 #define CONFIG_SYS_CCSRBAR              0xe0000000
  76 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  77
  78 /* DDR Setup */
  79 #define CONFIG_FSL_DDR2
  80 #undef CONFIG_FSL_DDR_INTERACTIVE
  81 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup*/
  82 #define CONFIG_DDR_SPD
  83 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
  84
  85 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
  86
  87 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  88 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  89
  90 #define CONFIG_NUM_DDR_CONTROLLERS      1
  91 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  92 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
  93
  94 /* I2C addresses of SPD EEPROMs */
  95 #define SPD_EEPROM_ADDRESS      0x51    /* CTLR 0 DIMM 0 */
  96
  97 /* Make sure required options are set */
  98 #ifndef CONFIG_SPD_EEPROM
  99 #error ("CONFIG_SPD_EEPROM is required")
 100 #endif
 101
 102 #undef CONFIG_CLOCKS_IN_MHZ
 103
 104 /*
 105  * Local Bus Definitions
 106  */
 107
 108 /*
 109  * FLASH on the Local Bus
 110  * Two banks, 8M each, using the CFI driver.
 111  * Boot from BR0/OR0 bank at 0xff00_0000
 112  * Alternate BR1/OR1 bank at 0xff80_0000
 113  *
 114  * BR0, BR1:
 115  *    Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
 116  *    Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
 117  *    Port Size = 16 bits = BRx[19:20] = 10
 118  *    Use GPCM = BRx[24:26] = 000
 119  *    Valid = BRx[31] = 1
 120  *
 121  * 0    4    8    12   16   20   24   28
 122  * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001    BR0
 123  * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001    BR1
 124  *
 125  * OR0, OR1:
 126  *    Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
 127  *    Reserved ORx[17:18] = 11, confusion here?
 128  *    CSNT = ORx[20] = 1
 129  *    ACS = half cycle delay = ORx[21:22] = 11
 130  *    SCY = 6 = ORx[24:27] = 0110
 131  *    TRLX = use relaxed timing = ORx[29] = 1
 132  *    EAD = use external address latch delay = OR[31] = 1
 133  *
 134  * 0    4    8    12   16   20   24   28
 135  * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65    ORx
 136  */
 137 #define CONFIG_SYS_BCSR_BASE            0xf8000000
 138
 139 #define CONFIG_SYS_FLASH_BASE           0xfe000000      /* start of FLASH 32M */
 140
 141 /*Chip select 0 - Flash*/
 142 #define CONFIG_SYS_BR0_PRELIM           0xfe001001
 143 #define CONFIG_SYS_OR0_PRELIM           0xfe006ff7
 144
 145 /*Chip slelect 1 - BCSR*/
 146 #define CONFIG_SYS_BR1_PRELIM           0xf8000801
 147 #define CONFIG_SYS_OR1_PRELIM           0xffffe9f7
 148
 149 /*#define CONFIG_SYS_FLASH_BANKS_LIST   {0xff800000, CONFIG_SYS_FLASH_BASE} */
 150 #define CONFIG_SYS_MAX_FLASH_BANKS              1               /* number of banks */
 151 #define CONFIG_SYS_MAX_FLASH_SECT               512             /* sectors per device */
 152 #undef  CONFIG_SYS_FLASH_CHECKSUM
 153 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 154 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Flash Write Timeout (ms) */
 155
 156 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 157
 158 #define CONFIG_FLASH_CFI_DRIVER
 159 #define CONFIG_SYS_FLASH_CFI
 160 #define CONFIG_SYS_FLASH_EMPTY_INFO
 161
 162
 163 /*
 164  * SDRAM on the LocalBus
 165  */
 166 #define CONFIG_SYS_LBC_SDRAM_BASE       0xf0000000      /* Localbus SDRAM        */
 167 #define CONFIG_SYS_LBC_SDRAM_SIZE       64                      /* LBC SDRAM is 64MB */
 168
 169
 170 /*Chip select 2 - SDRAM*/
 171 #define CONFIG_SYS_BR2_PRELIM      0xf0001861
 172 #define CONFIG_SYS_OR2_PRELIM           0xfc006901
 173
 174 #define CONFIG_SYS_LBC_LCRR             0x00030004      /* LB clock ratio reg */
 175 #define CONFIG_SYS_LBC_LBCR             0x00000000      /* LB config reg */
 176 #define CONFIG_SYS_LBC_LSRT             0x20000000      /* LB sdram refresh timer */
 177 #define CONFIG_SYS_LBC_MRTPR            0x00000000      /* LB refresh timer prescal*/
 178
 179 /*
 180  * Common settings for all Local Bus SDRAM commands.
 181  * At run time, either BSMA1516 (for CPU 1.1)
 182  *                  or BSMA1617 (for CPU 1.0) (old)
 183  * is OR'ed in too.
 184  */
 185 #define CONFIG_SYS_LBC_LSDMR_COMMON     ( LSDMR_RFCR16          \
 186                                 | LSDMR_PRETOACT7       \
 187                                 | LSDMR_ACTTORW7        \
 188                                 | LSDMR_BL8             \
 189                                 | LSDMR_WRC4            \
 190                                 | LSDMR_CL3             \
 191                                 | LSDMR_RFEN            \
 192                                 )
 193
 194 /*
 195  * The bcsr registers are connected to CS3 on MDS.
 196  * The new memory map places bcsr at 0xf8000000.
 197  *
 198  * For BR3, need:
 199  *    Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0
 200  *    port-size = 8-bits  = BR[19:20] = 01
 201  *    no parity checking  = BR[21:22] = 00
 202  *    GPMC for MSEL       = BR[24:26] = 000
 203  *    Valid               = BR[31]    = 1
 204  *
 205  * 0    4    8    12   16   20   24   28
 206  * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801
 207  *
 208  * For OR3, need:
 209  *    1 MB mask for AM,   OR[0:16]  = 1111 1111 1111 0000 0
 210  *    disable buffer ctrl OR[19]    = 0
 211  *    CSNT                OR[20]    = 1
 212  *    ACS                 OR[21:22] = 11
 213  *    XACS                OR[23]    = 1
 214  *    SCY 15 wait states  OR[24:27] = 1111      max is suboptimal but safe
 215  *    SETA                OR[28]    = 0
 216  *    TRLX                OR[29]    = 1
 217  *    EHTR                OR[30]    = 1
 218  *    EAD extra time      OR[31]    = 1
 219  *
 220  * 0    4    8    12   16   20   24   28
 221  * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
 222  */
 223 #define CONFIG_SYS_BCSR (0xf8000000)
 224
 225 /*Chip slelect 4 - PIB*/
 226 #define CONFIG_SYS_BR4_PRELIM   0xf8008801
 227 #define CONFIG_SYS_OR4_PRELIM   0xffffe9f7
 228
 229 /*Chip select 5 - PIB*/
 230 #define CONFIG_SYS_BR5_PRELIM    0xf8010801
 231 #define CONFIG_SYS_OR5_PRELIM    0xffff69f7
 232
 233 #define CONFIG_SYS_INIT_RAM_LOCK        1
 234 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000      /* Initial RAM address */
 235 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000      /* Size of used area in RAM */
 236
 237 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 238 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 239
 240 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024) /* Reserve 256 kB for Mon */
 241 #define CONFIG_SYS_MALLOC_LEN           (128 * 1024)    /* Reserved for malloc */
 242
 243 /* Serial Port */
 244 #define CONFIG_CONS_INDEX               1
 245 #define CONFIG_SYS_NS16550
 246 #define CONFIG_SYS_NS16550_SERIAL
 247 #define CONFIG_SYS_NS16550_REG_SIZE    1
 248 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 249
 250 #define CONFIG_SYS_BAUDRATE_TABLE  \
 251         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 252
 253 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 254 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 255
 256 /* Use the HUSH parser*/
 257 #define CONFIG_SYS_HUSH_PARSER
 258 #ifdef  CONFIG_SYS_HUSH_PARSER
 259 #endif
 260
 261 /* pass open firmware flat tree */
 262 #define CONFIG_OF_LIBFDT                1
 263 #define CONFIG_OF_BOARD_SETUP           1
 264 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 265
 266 /*
 267  * I2C
 268  */
 269 #define CONFIG_FSL_I2C          /* Use FSL common I2C driver */
 270 #define CONFIG_HARD_I2C         /* I2C with hardware support*/
 271 #define CONFIG_I2C_MULTI_BUS
 272 #define CONFIG_SYS_I2C_SPEED            400000  /* I2C speed and slave address */
 273 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x52
 274 #define CONFIG_SYS_I2C_SLAVE            0x7F
 275 #define CONFIG_SYS_I2C_NOPROBES        {{0,0x69}}       /* Don't probe these addrs */
 276 #define CONFIG_SYS_I2C_OFFSET           0x3000
 277 #define CONFIG_SYS_I2C2_OFFSET          0x3100
 278
 279 /*
 280  * General PCI
 281  * Memory Addresses are mapped 1-1. I/O is mapped from 0
 282  */
 283 #define CONFIG_SYS_PCI1_MEM_VIRT        0x80000000
 284 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
 285 #define CONFIG_SYS_PCI1_MEM_PHYS        0x80000000
 286 #define CONFIG_SYS_PCI1_MEM_SIZE        0x20000000      /* 512M */
 287 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
 288 #define CONFIG_SYS_PCI1_IO_BUS  0x00000000
 289 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
 290 #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000      /* 8M */
 291
 292 #define CONFIG_SYS_PCIE1_NAME           "Slot"
 293 #define CONFIG_SYS_PCIE1_MEM_VIRT       0xa0000000
 294 #define CONFIG_SYS_PCIE1_MEM_BUS        0xa0000000
 295 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xa0000000
 296 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 297 #define CONFIG_SYS_PCIE1_IO_VIRT        0xe2800000
 298 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
 299 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe2800000
 300 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 301
 302 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xC0000000
 303 #define CONFIG_SYS_SRIO1_MEM_BUS        0xC0000000
 304 #define CONFIG_SYS_SRIO1_MEM_PHYS       CONFIG_SYS_SRIO1_MEM_BUS
 305 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 512M */
 306
 307 #ifdef CONFIG_QE
 308 /*
 309  * QE UEC ethernet configuration
 310  */
 311 #define CONFIG_UEC_ETH
 312 #ifndef CONFIG_TSEC_ENET
 313 #define CONFIG_ETHPRIME         "UEC0"
 314 #endif
 315 #define CONFIG_PHY_MODE_NEED_CHANGE
 316 #define CONFIG_eTSEC_MDIO_BUS
 317
 318 #ifdef CONFIG_eTSEC_MDIO_BUS
 319 #define CONFIG_MIIM_ADDRESS     0xE0024520
 320 #endif
 321
 322 #define CONFIG_UEC_ETH1         /* GETH1 */
 323
 324 #ifdef CONFIG_UEC_ETH1
 325 #define CONFIG_SYS_UEC1_UCC_NUM        0       /* UCC1 */
 326 #define CONFIG_SYS_UEC1_RX_CLK         QE_CLK_NONE
 327 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16
 328 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 329 #define CONFIG_SYS_UEC1_PHY_ADDR       7
 330 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 331 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 332 #endif
 333
 334 #define CONFIG_UEC_ETH2         /* GETH2 */
 335
 336 #ifdef CONFIG_UEC_ETH2
 337 #define CONFIG_SYS_UEC2_UCC_NUM        1       /* UCC2 */
 338 #define CONFIG_SYS_UEC2_RX_CLK         QE_CLK_NONE
 339 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16
 340 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 341 #define CONFIG_SYS_UEC2_PHY_ADDR       1
 342 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 343 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 344 #endif
 345 #endif /* CONFIG_QE */
 346
 347 #if defined(CONFIG_PCI)
 348
 349 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 350
 351 #undef CONFIG_EEPRO100
 352 #undef CONFIG_TULIP
 353
 354 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 355 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
 356
 357 #endif  /* CONFIG_PCI */
 358
 359 #if defined(CONFIG_TSEC_ENET)
 360
 361 #define CONFIG_MII              1       /* MII PHY management */
 362 #define CONFIG_TSEC1    1
 363 #define CONFIG_TSEC1_NAME       "eTSEC0"
 364 #define CONFIG_TSEC2    1
 365 #define CONFIG_TSEC2_NAME       "eTSEC1"
 366
 367 #define TSEC1_PHY_ADDR          2
 368 #define TSEC2_PHY_ADDR          3
 369
 370 #define TSEC1_PHYIDX            0
 371 #define TSEC2_PHYIDX            0
 372
 373 #define TSEC1_FLAGS             TSEC_GIGABIT
 374 #define TSEC2_FLAGS             TSEC_GIGABIT
 375
 376 /* Options are: eTSEC[0-1] */
 377 #define CONFIG_ETHPRIME         "eTSEC0"
 378
 379 #endif  /* CONFIG_TSEC_ENET */
 380
 381 /*
 382  * Environment
 383  */
 384 #define CONFIG_ENV_IS_IN_FLASH  1
 385 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + 0x40000)
 386 #define CONFIG_ENV_SECT_SIZE    0x40000 /* 256K(one sector) for env */
 387 #define CONFIG_ENV_SIZE         0x2000
 388
 389 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 390 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 391
 392
 393 /*
 394  * BOOTP options
 395  */
 396 #define CONFIG_BOOTP_BOOTFILESIZE
 397 #define CONFIG_BOOTP_BOOTPATH
 398 #define CONFIG_BOOTP_GATEWAY
 399 #define CONFIG_BOOTP_HOSTNAME
 400
 401
 402 /*
 403  * Command line configuration.
 404  */
 405 #include <config_cmd_default.h>
 406
 407 #define CONFIG_CMD_PING
 408 #define CONFIG_CMD_I2C
 409 #define CONFIG_CMD_MII
 410 #define CONFIG_CMD_ELF
 411 #define CONFIG_CMD_IRQ
 412 #define CONFIG_CMD_SETEXPR
 413 #define CONFIG_CMD_REGINFO
 414
 415 #if defined(CONFIG_PCI)
 416     #define CONFIG_CMD_PCI
 417 #endif
 418
 419
 420 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 421
 422 /*
 423  * Miscellaneous configurable options
 424  */
 425 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 426 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 427 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 428 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 429 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt */
 430 #if defined(CONFIG_CMD_KGDB)
 431 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 432 #else
 433 #define CONFIG_SYS_CBSIZE       256                     /* Console I/O Buffer Size */
 434 #endif
 435 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 436 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 437 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 438 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1ms ticks */
 439
 440 /*
 441  * For booting Linux, the board info and command line data
 442  * have to be in the first 64 MB of memory, since this is
 443  * the maximum mapped by the Linux kernel during initialization.
 444  */
 445 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory map for Linux*/
 446 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 447
 448 #if defined(CONFIG_CMD_KGDB)
 449 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 450 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 451 #endif
 452
 453 /*
 454  * Environment Configuration
 455  */
 456
 457 /* The mac addresses for all ethernet interface */
 458 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
 459 #define CONFIG_HAS_ETH0
 460 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 461 #define CONFIG_HAS_ETH1
 462 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
 463 #define CONFIG_HAS_ETH2
 464 #define CONFIG_ETH2ADDR  00:E0:0C:00:02:FD
 465 #define CONFIG_HAS_ETH3
 466 #define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 467 #endif
 468
 469 #define CONFIG_IPADDR    192.168.1.253
 470
 471 #define CONFIG_HOSTNAME  unknown
 472 #define CONFIG_ROOTPATH  "/nfsroot"
 473 #define CONFIG_BOOTFILE  "your.uImage"
 474
 475 #define CONFIG_SERVERIP  192.168.1.1
 476 #define CONFIG_GATEWAYIP 192.168.1.1
 477 #define CONFIG_NETMASK   255.255.255.0
 478
 479 #define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
 480
 481 #define CONFIG_BOOTDELAY 10       /* -1 disables auto-boot */
 482 #undef  CONFIG_BOOTARGS           /* the boot command will set bootargs*/
 483
 484 #define CONFIG_BAUDRATE 115200
 485
 486 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 487    "netdev=eth0\0"                                                      \
 488    "consoledev=ttyS0\0"                                                 \
 489    "ramdiskaddr=600000\0"                                               \
 490    "ramdiskfile=your.ramdisk.u-boot\0"                                  \
 491    "fdtaddr=400000\0"                                                   \
 492    "fdtfile=your.fdt.dtb\0"                                             \
 493    "nfsargs=setenv bootargs root=/dev/nfs rw "                          \
 494       "nfsroot=$serverip:$rootpath "                                    \
 495       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 496       "console=$consoledev,$baudrate $othbootargs\0"                    \
 497    "ramargs=setenv bootargs root=/dev/ram rw "                          \
 498       "console=$consoledev,$baudrate $othbootargs\0"                    \
 499
 500
 501 #define CONFIG_NFSBOOTCOMMAND                                           \
 502    "run nfsargs;"                                                       \
 503    "tftp $loadaddr $bootfile;"                                          \
 504    "tftp $fdtaddr $fdtfile;"                                            \
 505    "bootm $loadaddr - $fdtaddr"
 506
 507
 508 #define CONFIG_RAMBOOTCOMMAND \
 509    "run ramargs;"                                                       \
 510    "tftp $ramdiskaddr $ramdiskfile;"                                    \
 511    "tftp $loadaddr $bootfile;"                                          \
 512    "bootm $loadaddr $ramdiskaddr"
 513
 514 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 515
 516 #endif  /* __CONFIG_H */