powerpc: convert selected boards to generic board structure

[people/ms/u-boot.git] / include / configs / MPC8610HPCD.h

/*
 * Copyright 2007-2011 Freescale Semiconductor, Inc.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * Version 2 as published by the Free Software Foundation.
 */

/*
 * MPC8610HPCD board configuration file
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO

/* High Level Configuration Options */
#define CONFIG_MPC8610          1       /* MPC8610 specific */
#define CONFIG_MPC8610HPCD      1       /* MPC8610HPCD board specific */
#define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */

#define CONFIG_SYS_TEXT_BASE    0xfff00000


/* video */
#define CONFIG_FSL_DIU_FB

#ifdef CONFIG_FSL_DIU_FB
#define CONFIG_SYS_DIU_ADDR     (CONFIG_SYS_CCSRBAR + 0x2c000)
#define CONFIG_VIDEO
#define CONFIG_CMD_BMP
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#endif

#ifdef RUN_DIAG
#define CONFIG_SYS_DIAG_ADDR            0xff800000
#endif

/*
 * virtual address to be used for temporary mappings.  There
 * should be 128k free at this VA.
 */
#define CONFIG_SYS_SCRATCH_VA   0xc0000000

#define CONFIG_PCI              1       /* Enable PCI/PCIE*/
#define CONFIG_PCI1             1       /* PCI controler 1 */
#define CONFIG_PCIE1            1       /* PCIe 1 connected to ULI bridge */
#define CONFIG_PCIE2            1       /* PCIe 2 connected to slot */
#define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
#define CONFIG_FSL_LAW          1       /* Use common FSL init code */

#define CONFIG_ENV_OVERWRITE
#define CONFIG_INTERRUPTS               /* enable pci, srio, ddr interrupts */

#define CONFIG_BAT_RW           1       /* Use common BAT rw code */
#define CONFIG_HIGH_BATS        1       /* High BATs supported & enabled */
#define CONFIG_ALTIVEC          1

/*
 * L2CR setup -- make sure this is right for your board!
 */
#define CONFIG_SYS_L2
#define L2_INIT         0
#define L2_ENABLE       (L2CR_L2E |0x00100000 )

#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
#endif

#define CONFIG_BOARD_EARLY_INIT_F       1       /* Call board_pre_init */
#define CONFIG_MISC_INIT_R              1

#define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
#define CONFIG_SYS_MEMTEST_END          0x00400000

/*
 * Base addresses -- Note these are effective addresses where the
 * actual resources get mapped (not physical addresses)
 */
#define CONFIG_SYS_CCSRBAR_DEFAULT      0xff700000      /* CCSRBAR Default */
#define CONFIG_SYS_CCSRBAR              0xe0000000      /* relocated CCSRBAR */
#define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */

#define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
#define CONFIG_SYS_CCSRBAR_PHYS_HIGH    0x0
#define CONFIG_SYS_CCSRBAR_PHYS         CONFIG_SYS_CCSRBAR_PHYS_LOW

/* DDR Setup */
#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM               /* Use SPD for DDR */
#define CONFIG_DDR_SPD

#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE   0xDeadBeef

#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
#define CONFIG_VERY_BIG_RAM

#define CONFIG_NUM_DDR_CONTROLLERS      1
#define CONFIG_DIMM_SLOTS_PER_CTLR      1
#define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)

#define SPD_EEPROM_ADDRESS      0x51    /* CTLR 0 DIMM 0 */

/* These are used when DDR doesn't use SPD.  */
#define CONFIG_SYS_SDRAM_SIZE   256             /* DDR is 256MB */

#if 0 /* TODO */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
#define CONFIG_SYS_DDR_CS0_CONFIG       0x80010202      /* Enable, no interleaving */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_TIMING_0 0x00260802
#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
#define CONFIG_SYS_DDR_MODE_1           0x00480432
#define CONFIG_SYS_DDR_MODE_2           0x00000000
#define CONFIG_SYS_DDR_INTERVAL 0x06180100
#define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
#define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
#define CONFIG_SYS_DDR_CONTROL          0xe3008000      /* Type = DDR2 */
#define CONFIG_SYS_DDR_CONTROL2 0x04400010

#define CONFIG_SYS_DDR_ERR_INT_EN       0x00000000
#define CONFIG_SYS_DDR_ERR_DIS          0x00000000
#define CONFIG_SYS_DDR_SBE              0x000f0000

#endif


#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1


#define CONFIG_SYS_FLASH_BASE           0xf0000000 /* start of FLASH 128M */
#define CONFIG_SYS_FLASH_BASE2          0xf8000000

#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}

#define CONFIG_SYS_BR0_PRELIM           0xf8001001 /* port size 16bit */
#define CONFIG_SYS_OR0_PRELIM           0xf8006e65 /* 128MB NOR Flash*/

#define CONFIG_SYS_BR1_PRELIM           0xf0001001 /* port size 16bit */
#define CONFIG_SYS_OR1_PRELIM           0xf8006e65 /* 128MB Promjet */
#if 0 /* TODO */
#define CONFIG_SYS_BR2_PRELIM           0xf0000000
#define CONFIG_SYS_OR2_PRELIM           0xf0000000 /* 256MB NAND Flash - bank 1 */
#endif
#define CONFIG_SYS_BR3_PRELIM           0xe8000801 /* port size 8bit */
#define CONFIG_SYS_OR3_PRELIM           0xfff06ff7 /* 1MB PIXIS area*/


#define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
#define PIXIS_BASE      0xe8000000      /* PIXIS registers */
#define PIXIS_ID                0x0     /* Board ID at offset 0 */
#define PIXIS_VER               0x1     /* Board version at offset 1 */
#define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
#define PIXIS_RST               0x4     /* PIXIS Reset Control register */
#define PIXIS_AUX               0x6     /* PIXIS Auxiliary register; Scratch */
#define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
#define PIXIS_BRDCFG0           0x8     /* PIXIS Board Configuration Register0*/
#define PIXIS_VCTL              0x10    /* VELA Control Register */
#define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
#define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
#define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
#define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
#define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
#define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
#define CONFIG_SYS_PIXIS_VBOOT_MASK     0xC0    /* Reset altbank mask */

#define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */

#undef  CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
#define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef  CONFIG_SYS_RAMBOOT
#endif

#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_SPD_EEPROM
#define CONFIG_SYS_SDRAM_SIZE   256
#endif

#undef CONFIG_CLOCKS_IN_MHZ

#define CONFIG_SYS_INIT_RAM_LOCK        1
#ifndef CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000      /* Initial RAM address */
#else
#define CONFIG_SYS_INIT_RAM_ADDR        0xe4000000      /* Initial RAM address */
#endif
#define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */

#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
#define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)       /* Reserved for malloc */

/* Serial Port */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/*
 * Pass open firmware flat tree to kernel
 */
#define CONFIG_OF_LIBFDT                1
#define CONFIG_OF_BOARD_SETUP           1
#define CONFIG_OF_STDOUT_VIA_ALIAS      1


/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE   8192

/*
 * I2C
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
#define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCI1_MEM_BUS         0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BUS
#define CONFIG_SYS_PCI1_MEM_VIRT        CONFIG_SYS_PCI1_MEM_BUS
#define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
#define CONFIG_SYS_PCI1_IO_BUS  0x0000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
#define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000      /* 1M */

/* controller 1, Base address 0xa000 */
#define CONFIG_SYS_PCIE1_NAME           "ULI"
#define CONFIG_SYS_PCIE1_MEM_BUS        0xa0000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000      /* 256M */
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS        0xe3000000
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00100000      /* 1M */

/* controller 2, Base Address 0x9000 */
#define CONFIG_SYS_PCIE2_NAME           "Slot 1"
#define CONFIG_SYS_PCIE2_MEM_BUS        0x90000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
#define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
#define CONFIG_SYS_PCIE2_IO_BUS         0x00000000      /* reuse mem LAW */
#define CONFIG_SYS_PCIE2_IO_PHYS        0xe2000000
#define CONFIG_SYS_PCIE2_IO_SIZE        0x00100000      /* 1M */


#if defined(CONFIG_PCI)

#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */

#define CONFIG_PCI_PNP          /* do pci plug-and-play */
#define CONFIG_CMD_REGINFO

#define CONFIG_ULI526X
#ifdef CONFIG_ULI526X
#endif

/************************************************************
 * USB support
 ************************************************************/
#define CONFIG_PCI_OHCI         1
#define CONFIG_USB_OHCI_NEW             1
#define CONFIG_USB_KEYBOARD     1
#define CONFIG_SYS_STDIO_DEREGISTER
#define CONFIG_SYS_USB_EVENT_POLL       1
#define CONFIG_SYS_USB_OHCI_SLOT_NAME   "ohci_pci"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1

#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR        0xe0000000
#define PCI_ENET0_MEMADDR       0xe0000000
#define PCI_IDSEL_NUMBER        0x0c    /* slot0->3(IDSEL)=12->15 */
#endif

#define CONFIG_DOS_PARTITION
#define CONFIG_SCSI_AHCI

#ifdef CONFIG_SCSI_AHCI
#define CONFIG_LIBATA
#define CONFIG_SATA_ULI5288
#define CONFIG_SYS_SCSI_MAX_SCSI_ID     4
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_SYS_SCSI_MAXDEVICE       CONFIG_SYS_SCSI_MAX_DEVICE
#endif

#endif  /* CONFIG_PCI */

/*
 * BAT0         2G      Cacheable, non-guarded
 * 0x0000_0000  2G      DDR
 */
#define CONFIG_SYS_DBAT0L       (BATL_PP_RW)
#define CONFIG_SYS_IBAT0L       (BATL_PP_RW)

/*
 * BAT1         1G      Cache-inhibited, guarded
 * 0x8000_0000  256M    PCI-1 Memory
 * 0xa000_0000  256M    PCI-Express 1 Memory
 * 0x9000_0000  256M    PCI-Express 2 Memory
 */

#define CONFIG_SYS_DBAT1L       (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
                        | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT1U       (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U

/*
 * BAT2         16M     Cache-inhibited, guarded
 * 0xe100_0000  1M      PCI-1 I/O
 */

#define CONFIG_SYS_DBAT2L       (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
                        | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U

/*
 * BAT3         4M      Cache-inhibited, guarded
 * 0xe000_0000  4M      CCSR
 */

#define CONFIG_SYS_DBAT3L       (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
                        | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT3L       (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U

#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
                                       | BATL_PP_RW | BATL_CACHEINHIBIT \
                                       | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
                                       | BATU_BL_1M | BATU_VS | BATU_VP)
#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
                                       | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
#endif

/*
 * BAT4         32M     Cache-inhibited, guarded
 * 0xe200_0000  1M      PCI-Express 2 I/O
 * 0xe300_0000  1M      PCI-Express 1 I/O
 */

#define CONFIG_SYS_DBAT4L       (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
                        | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U


/*
 * BAT5         128K    Cacheable, non-guarded
 * 0xe400_0000  128K    Init RAM for stack in the CPU DCache (no backing memory)
 */
#define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
#define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U

/*
 * BAT6         256M    Cache-inhibited, guarded
 * 0xf000_0000  256M    FLASH
 */
#define CONFIG_SYS_DBAT6L       (CONFIG_SYS_FLASH_BASE   | BATL_PP_RW | BATL_CACHEINHIBIT \
                        | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE   | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT6L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U

/* Map the last 1M of flash where we're running from reset */
#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
                                 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
                                 | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY

/*
 * BAT7         4M      Cache-inhibited, guarded
 * 0xe800_0000  4M      PIXIS
 */
#define CONFIG_SYS_DBAT7L       (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
                        | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT7U       (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
#define CONFIG_SYS_IBAT7L       (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT7U       CONFIG_SYS_DBAT7U


/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
#define CONFIG_ENV_IS_IN_FLASH  1
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#define CONFIG_ENV_SECT_SIZE    0x20000 /* 126k (one sector) for env */
#define CONFIG_ENV_SIZE         0x2000
#else
#define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE         0x2000
#endif

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII

#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_USB
#endif


#define CONFIG_WATCHDOG                 /* watchdog enabled */
#define CONFIG_SYS_WATCHDOG_FREQ        5000    /* Feed interval, 5s */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_CMDLINE_EDITING          /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS      16              /* max number of command args */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (8 << 20)       /* Initial Memory map for Linux*/

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_IPADDR           192.168.1.100

#define CONFIG_HOSTNAME         unknown
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"
#define CONFIG_UBOOTPATH        8610hpcd/u-boot.bin

#define CONFIG_SERVERIP         192.168.1.1
#define CONFIG_GATEWAYIP        192.168.1.1
#define CONFIG_NETMASK          255.255.255.0

/* default location for tftp and bootm */
#define CONFIG_LOADADDR         1000000

#define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
#undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */

#define CONFIG_BAUDRATE 115200

#if defined(CONFIG_PCI1)
#define PCI_ENV \
 "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
        "echo e;md ${a}e00 9\0" \
 "pci1regs=setenv a e0008; run pcireg\0" \
 "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
        "pci d.w $b.0 56 1\0" \
 "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
        "pci w.w $b.0 56 ffff\0"        \
 "pci1err=setenv a e0008; run pcierr\0" \
 "pci1errc=setenv a e0008; run pcierrc\0"
#else
#define PCI_ENV ""
#endif

#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
#define PCIE_ENV \
 "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
        "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
 "pcie1regs=setenv a e000a; run pciereg\0"      \
 "pcie2regs=setenv a e0009; run pciereg\0"      \
 "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
        "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;"        \
        "pci d $b.0 130 1\0" \
 "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
        "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
        "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0"            \
 "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"       \
 "pcie1err=setenv a e000a; run pcieerr\0"       \
 "pcie2err=setenv a e0009; run pcieerr\0"       \
 "pcie1errc=setenv a e000a; run pcieerrc\0"     \
 "pcie2errc=setenv a e0009; run pcieerrc\0"
#else
#define PCIE_ENV ""
#endif

#define DMA_ENV \
 "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
        "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
 "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
        "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
 "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
        "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
 "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
        "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"

#ifdef ENV_DEBUG
#define CONFIG_EXTRA_ENV_SETTINGS                               \
"netdev=eth0\0"                                                 \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
"tftpflash=tftpboot $loadaddr $uboot; "                         \
        "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
                " +$filesize; " \
        "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
                " +$filesize; " \
        "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
                " $filesize; "  \
        "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
                " +$filesize; " \
        "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
                " $filesize\0"  \
"consoledev=ttyS0\0"                                            \
"ramdiskaddr=2000000\0"                                 \
"ramdiskfile=8610hpcd/ramdisk.uboot\0"                          \
"fdtaddr=c00000\0"                                              \
"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"                           \
"bdev=sda3\0"                                   \
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
"maxcpus=1"     \
"eoi=mw e00400b0 0\0"                                           \
"iack=md e00400a0 1\0"                                          \
"ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
        "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
        "md ${a}f00 5\0" \
"ddr1regs=setenv a e0002; run ddrreg\0" \
"gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
        "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
        "md ${a}e60 1; md ${a}ef0 1d\0" \
"guregs=setenv a e00e0; run gureg\0" \
"mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
"mcmregs=setenv a e0001; run mcmreg\0" \
"diuregs=md e002c000 1d\0" \
"dium=mw e002c01c\0" \
"diuerr=md e002c014 1\0" \
"pmregs=md e00e1000 2b\0" \
"lawregs=md e0000c08 4b\0" \
"lbcregs=md e0005000 36\0" \
"dma0regs=md e0021100 12\0" \
"dma1regs=md e0021180 12\0" \
"dma2regs=md e0021200 12\0" \
"dma3regs=md e0021280 12\0" \
 PCI_ENV \
 PCIE_ENV \
 DMA_ENV
#else
#define CONFIG_EXTRA_ENV_SETTINGS                               \
        "netdev=eth0\0"                                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
        "consoledev=ttyS0\0"                                    \
        "ramdiskaddr=2000000\0"                                 \
        "ramdiskfile=8610hpcd/ramdisk.uboot\0"                  \
        "fdtaddr=c00000\0"                                      \
        "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"                   \
        "bdev=sda3\0"
#endif

#define CONFIG_NFSBOOTCOMMAND                                   \
 "setenv bootargs root=/dev/nfs rw "                            \
        "nfsroot=$serverip:$rootpath "                          \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;"           \
 "tftp $loadaddr $bootfile;"                                    \
 "tftp $fdtaddr $fdtfile;"                                      \
 "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND \
 "setenv bootargs root=/dev/ram rw "                            \
        "console=$consoledev,$baudrate $othbootargs;"           \
 "tftp $ramdiskaddr $ramdiskfile;"                              \
 "tftp $loadaddr $bootfile;"                                    \
 "tftp $fdtaddr $fdtfile;"                                      \
 "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND              \
 "setenv bootargs root=/dev/$bdev rw "  \
        "console=$consoledev,$baudrate $othbootargs;"   \
 "tftp $loadaddr $bootfile;"            \
 "tftp $fdtaddr $fdtfile;"              \
 "bootm $loadaddr - $fdtaddr"

#endif  /* __CONFIG_H */