include/configs/MPC8641HPCN.h

   1 /*
   2  * Copyright 2006, 2010-2011 Freescale Semiconductor.
   3  *
   4  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * MPC8641HPCN board configuration file
  11  *
  12  * Make sure you change the MAC address and other network params first,
  13  * search for CONFIG_SERVERIP, etc. in this file.
  14  */
  15
  16 #ifndef __CONFIG_H
  17 #define __CONFIG_H
  18
  19 /* High Level Configuration Options */
  20 #define CONFIG_MP               1       /* support multiple processors */
  21 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  22 #define CONFIG_ADDR_MAP         1       /* Use addr map */
  23
  24 /*
  25  * default CCSRBAR is at 0xff700000
  26  * assume U-Boot is less than 0.5MB
  27  */
  28 #define CONFIG_SYS_TEXT_BASE    0xeff00000
  29
  30 #ifdef RUN_DIAG
  31 #define CONFIG_SYS_DIAG_ADDR         CONFIG_SYS_FLASH_BASE
  32 #endif
  33
  34 /*
  35  * virtual address to be used for temporary mappings.  There
  36  * should be 128k free at this VA.
  37  */
  38 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  39
  40 #define CONFIG_SYS_SRIO
  41 #define CONFIG_SRIO1                    /* SRIO port 1 */
  42
  43 #define CONFIG_PCIE1            1       /* PCIE controller 1 (ULI bridge) */
  44 #define CONFIG_PCIE2            1       /* PCIE controller 2 (slot) */
  45 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  46 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  47
  48 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
  49 #define CONFIG_ENV_OVERWRITE
  50
  51 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  52 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  53 #define CONFIG_SYS_NUM_ADDR_MAP 8       /* Number of addr map slots = 8 dbats */
  54
  55 #define CONFIG_ALTIVEC          1
  56
  57 /*
  58  * L2CR setup -- make sure this is right for your board!
  59  */
  60 #define CONFIG_SYS_L2
  61 #define L2_INIT         0
  62 #define L2_ENABLE       (L2CR_L2E)
  63
  64 #ifndef CONFIG_SYS_CLK_FREQ
  65 #ifndef __ASSEMBLY__
  66 extern unsigned long get_board_sys_clk(unsigned long dummy);
  67 #endif
  68 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  69 #endif
  70
  71 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  72 #define CONFIG_SYS_MEMTEST_END          0x00400000
  73
  74 /*
  75  * With the exception of PCI Memory and Rapid IO, most devices will simply
  76  * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
  77  * when 36-bit is enabled.  When 36-bit is not enabled, these bits are 0.
  78  */
  79 #ifdef CONFIG_PHYS_64BIT
  80 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f
  81 #else
  82 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000
  83 #endif
  84
  85 /*
  86  * Base addresses -- Note these are effective addresses where the
  87  * actual resources get mapped (not physical addresses)
  88  */
  89 #define CONFIG_SYS_CCSRBAR              0xffe00000      /* relocated CCSRBAR */
  90 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
  91
  92 /* Physical addresses */
  93 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  94 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    CONFIG_SYS_PHYS_ADDR_HIGH
  95 #define CONFIG_SYS_CCSRBAR_PHYS \
  96         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
  97                             CONFIG_SYS_CCSRBAR_PHYS_HIGH)
  98
  99 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */
 100
 101 /*
 102  * DDR Setup
 103  */
 104 #define CONFIG_FSL_DDR_INTERACTIVE
 105 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
 106 #define CONFIG_DDR_SPD
 107
 108 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
 109 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
 110
 111 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
 112 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 113 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
 114 #define CONFIG_VERY_BIG_RAM
 115
 116 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 117 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 118
 119 /*
 120  * I2C addresses of SPD EEPROMs
 121  */
 122 #define SPD_EEPROM_ADDRESS1     0x51    /* CTLR 0 DIMM 0 */
 123 #define SPD_EEPROM_ADDRESS2     0x52    /* CTLR 0 DIMM 1 */
 124 #define SPD_EEPROM_ADDRESS3     0x53    /* CTLR 1 DIMM 0 */
 125 #define SPD_EEPROM_ADDRESS4     0x54    /* CTLR 1 DIMM 1 */
 126
 127 /*
 128  * These are used when DDR doesn't use SPD.
 129  */
 130 #define CONFIG_SYS_SDRAM_SIZE           256             /* DDR is 256MB */
 131 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
 132 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80010102      /* Enable, no interleaving */
 133 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 134 #define CONFIG_SYS_DDR_TIMING_0 0x00260802
 135 #define CONFIG_SYS_DDR_TIMING_1 0x39357322
 136 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
 137 #define CONFIG_SYS_DDR_MODE_1           0x00480432
 138 #define CONFIG_SYS_DDR_MODE_2           0x00000000
 139 #define CONFIG_SYS_DDR_INTERVAL 0x06090100
 140 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 141 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
 142 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
 143 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 144 #define CONFIG_SYS_DDR_CONTROL          0xe3008000      /* Type = DDR2 */
 145 #define CONFIG_SYS_DDR_CONTROL2 0x04400000
 146
 147 #define CONFIG_ID_EEPROM
 148 #define CONFIG_SYS_I2C_EEPROM_NXID
 149 #define CONFIG_ID_EEPROM
 150 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 151 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 152
 153 #define CONFIG_SYS_FLASH_BASE           0xef800000     /* start of FLASH 8M */
 154 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW  CONFIG_SYS_FLASH_BASE
 155 #define CONFIG_SYS_FLASH_BASE_PHYS \
 156         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 157                             CONFIG_SYS_PHYS_ADDR_HIGH)
 158
 159 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
 160
 161 #define CONFIG_SYS_BR0_PRELIM   (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 162                                  | 0x00001001)  /* port size 16bit */
 163 #define CONFIG_SYS_OR0_PRELIM   0xff806ff7      /* 8MB Boot Flash area*/
 164
 165 #define CONFIG_SYS_BR2_PRELIM   (BR_PHYS_ADDR(CF_BASE_PHYS)             \
 166                                  | 0x00001001)  /* port size 16bit */
 167 #define CONFIG_SYS_OR2_PRELIM   0xffffeff7      /* 32k Compact Flash */
 168
 169 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(PIXIS_BASE_PHYS)  \
 170                                  | 0x00000801) /* port size 8bit */
 171 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32k PIXIS area*/
 172
 173 /*
 174  * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
 175  * The PIXIS and CF by themselves aren't large enough to take up the 128k
 176  * required for the smallest BAT mapping, so there's a 64k hole.
 177  */
 178 #define CONFIG_SYS_LBC_BASE             0xffde0000
 179 #define CONFIG_SYS_LBC_BASE_PHYS_LOW    CONFIG_SYS_LBC_BASE
 180
 181 #define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
 182 #define PIXIS_BASE              (CONFIG_SYS_LBC_BASE + 0x00010000)
 183 #define PIXIS_BASE_PHYS_LOW     (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000)
 184 #define PIXIS_BASE_PHYS         PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \
 185                                                     CONFIG_SYS_PHYS_ADDR_HIGH)
 186 #define PIXIS_SIZE              0x00008000      /* 32k */
 187 #define PIXIS_ID                0x0     /* Board ID at offset 0 */
 188 #define PIXIS_VER               0x1     /* Board version at offset 1 */
 189 #define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
 190 #define PIXIS_RST               0x4     /* PIXIS Reset Control register */
 191 #define PIXIS_AUX               0x6     /* PIXIS Auxiliary register; Scratch register */
 192 #define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
 193 #define PIXIS_VCTL              0x10    /* VELA Control Register */
 194 #define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
 195 #define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
 196 #define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
 197 #define PIXIS_VBOOT_FMAP        0x80    /* VBOOT - CFG_FLASHMAP */
 198 #define PIXIS_VBOOT_FBANK       0x40    /* VBOOT - CFG_FLASHBANK */
 199 #define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
 200 #define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
 201 #define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
 202 #define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
 203 #define CONFIG_SYS_PIXIS_VBOOT_MASK     0x40    /* Reset altbank mask*/
 204
 205 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
 206 #define CF_BASE                 (PIXIS_BASE + PIXIS_SIZE)
 207 #define CF_BASE_PHYS            (PIXIS_BASE_PHYS + PIXIS_SIZE)
 208
 209 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 210 #define CONFIG_SYS_MAX_FLASH_SECT       128             /* sectors per device */
 211
 212 #undef  CONFIG_SYS_FLASH_CHECKSUM
 213 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 214 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 215 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* start of monitor */
 216 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 217
 218 #define CONFIG_FLASH_CFI_DRIVER
 219 #define CONFIG_SYS_FLASH_CFI
 220 #define CONFIG_SYS_FLASH_EMPTY_INFO
 221
 222 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 223 #define CONFIG_SYS_RAMBOOT
 224 #else
 225 #undef  CONFIG_SYS_RAMBOOT
 226 #endif
 227
 228 #if defined(CONFIG_SYS_RAMBOOT)
 229 #undef CONFIG_SPD_EEPROM
 230 #define CONFIG_SYS_SDRAM_SIZE   256
 231 #endif
 232
 233 #undef CONFIG_CLOCKS_IN_MHZ
 234
 235 #define CONFIG_SYS_INIT_RAM_LOCK        1
 236 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 237 #define CONFIG_SYS_INIT_RAM_ADDR        0x0fd00000      /* Initial RAM address */
 238 #else
 239 #define CONFIG_SYS_INIT_RAM_ADDR        0xf8400000      /* Initial RAM address */
 240 #endif
 241 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */
 242
 243 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 244 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 245
 246 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 kB for Mon */
 247 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)    /* Reserved for malloc */
 248
 249 /* Serial Port */
 250 #define CONFIG_CONS_INDEX     1
 251 #define CONFIG_SYS_NS16550_SERIAL
 252 #define CONFIG_SYS_NS16550_REG_SIZE     1
 253 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 254
 255 #define CONFIG_SYS_BAUDRATE_TABLE  \
 256         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 257
 258 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 259 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 260
 261 /*
 262  * I2C
 263  */
 264 #define CONFIG_SYS_I2C
 265 #define CONFIG_SYS_I2C_FSL
 266 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 267 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 268 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3100
 269 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 270
 271 /*
 272  * RapidIO MMU
 273  */
 274 #define CONFIG_SYS_SRIO1_MEM_BASE       0x80000000      /* base address */
 275 #ifdef CONFIG_PHYS_64BIT
 276 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   0x00000000
 277 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x0000000c
 278 #else
 279 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   CONFIG_SYS_SRIO1_MEM_BASE
 280 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x00000000
 281 #endif
 282 #define CONFIG_SYS_SRIO1_MEM_PHYS \
 283         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 284                             CONFIG_SYS_SRIO1_MEM_PHYS_HIGH)
 285 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 128M */
 286
 287 /*
 288  * General PCI
 289  * Addresses are mapped 1-1.
 290  */
 291
 292 #define CONFIG_SYS_PCIE1_NAME           "ULI"
 293 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 294 #ifdef CONFIG_PHYS_64BIT
 295 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 296 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   0x00000000
 297 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x0000000c
 298 #else
 299 #define CONFIG_SYS_PCIE1_MEM_BUS        CONFIG_SYS_PCIE1_MEM_VIRT
 300 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   CONFIG_SYS_PCIE1_MEM_VIRT
 301 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x00000000
 302 #endif
 303 #define CONFIG_SYS_PCIE1_MEM_PHYS \
 304         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 305                             CONFIG_SYS_PCIE1_MEM_PHYS_HIGH)
 306 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 307 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 308 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 309 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW    CONFIG_SYS_PCIE1_IO_VIRT
 310 #define CONFIG_SYS_PCIE1_IO_PHYS \
 311         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 312                             CONFIG_SYS_PHYS_ADDR_HIGH)
 313 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64K */
 314
 315 #ifdef CONFIG_PHYS_64BIT
 316 /*
 317  * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT.
 318  * This will increase the amount of PCI address space available for
 319  * for mapping RAM.
 320  */
 321 #define CONFIG_SYS_PCIE2_MEM_BUS        CONFIG_SYS_PCIE1_MEM_BUS
 322 #else
 323 #define CONFIG_SYS_PCIE2_MEM_BUS        (CONFIG_SYS_PCIE1_MEM_BUS \
 324                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 325 #endif
 326 #define CONFIG_SYS_PCIE2_MEM_VIRT       (CONFIG_SYS_PCIE1_MEM_VIRT \
 327                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 328 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW   (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \
 329                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 330 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH  CONFIG_SYS_PCIE1_MEM_PHYS_HIGH
 331 #define CONFIG_SYS_PCIE2_MEM_PHYS       (CONFIG_SYS_PCIE1_MEM_PHYS \
 332                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 333 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 334 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 335 #define CONFIG_SYS_PCIE2_IO_VIRT        (CONFIG_SYS_PCIE1_IO_VIRT \
 336                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 337 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW    (CONFIG_SYS_PCIE1_IO_PHYS_LOW \
 338                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 339 #define CONFIG_SYS_PCIE2_IO_PHYS        (CONFIG_SYS_PCIE1_IO_PHYS \
 340                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 341 #define CONFIG_SYS_PCIE2_IO_SIZE        CONFIG_SYS_PCIE1_IO_SIZE
 342
 343 #if defined(CONFIG_PCI)
 344
 345 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 346
 347 #undef CONFIG_EEPRO100
 348 #undef CONFIG_TULIP
 349
 350 /************************************************************
 351  * USB support
 352  ************************************************************/
 353 #define CONFIG_PCI_OHCI                 1
 354 #define CONFIG_USB_OHCI_NEW             1
 355 #define CONFIG_SYS_USB_OHCI_SLOT_NAME           "ohci_pci"
 356 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 357 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 358
 359 /*PCIE video card used*/
 360 #define VIDEO_IO_OFFSET         CONFIG_SYS_PCIE2_IO_VIRT
 361
 362 /*PCI video card used*/
 363 /*#define VIDEO_IO_OFFSET       CONFIG_SYS_PCIE1_IO_VIRT*/
 364
 365 /* video */
 366
 367 #if defined(CONFIG_VIDEO)
 368 #define CONFIG_BIOSEMU
 369 #define CONFIG_ATI_RADEON_FB
 370 #define CONFIG_VIDEO_LOGO
 371 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT
 372 #endif
 373
 374 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 375
 376 #ifdef CONFIG_SCSI_AHCI
 377 #define CONFIG_SATA_ULI5288
 378 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     4
 379 #define CONFIG_SYS_SCSI_MAX_LUN 1
 380 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
 381 #define CONFIG_SYS_SCSI_MAXDEVICE       CONFIG_SYS_SCSI_MAX_DEVICE
 382 #endif
 383
 384 #endif  /* CONFIG_PCI */
 385
 386 #if defined(CONFIG_TSEC_ENET)
 387
 388 #define CONFIG_MII              1       /* MII PHY management */
 389
 390 #define CONFIG_TSEC1            1
 391 #define CONFIG_TSEC1_NAME       "eTSEC1"
 392 #define CONFIG_TSEC2            1
 393 #define CONFIG_TSEC2_NAME       "eTSEC2"
 394 #define CONFIG_TSEC3            1
 395 #define CONFIG_TSEC3_NAME       "eTSEC3"
 396 #define CONFIG_TSEC4            1
 397 #define CONFIG_TSEC4_NAME       "eTSEC4"
 398
 399 #define TSEC1_PHY_ADDR          0
 400 #define TSEC2_PHY_ADDR          1
 401 #define TSEC3_PHY_ADDR          2
 402 #define TSEC4_PHY_ADDR          3
 403 #define TSEC1_PHYIDX            0
 404 #define TSEC2_PHYIDX            0
 405 #define TSEC3_PHYIDX            0
 406 #define TSEC4_PHYIDX            0
 407 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 408 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 409 #define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 410 #define TSEC4_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 411
 412 #define CONFIG_ETHPRIME         "eTSEC1"
 413
 414 #endif  /* CONFIG_TSEC_ENET */
 415
 416 #ifdef CONFIG_PHYS_64BIT
 417 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
 418 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
 419
 420 /* Put physical address into the BAT format */
 421 #define BAT_PHYS_ADDR(low, high) \
 422         (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high))
 423 /* Convert high/low pairs to actual 64-bit value */
 424 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32))
 425 #else
 426 /* 32-bit systems just ignore the "high" bits */
 427 #define BAT_PHYS_ADDR(low, high)        (low)
 428 #define PAIRED_PHYS_TO_PHYS(low, high)  (low)
 429 #endif
 430
 431 /*
 432  * BAT0         DDR
 433  */
 434 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 435 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 436
 437 /*
 438  * BAT1         LBC (PIXIS/CF)
 439  */
 440 #define CONFIG_SYS_DBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 441                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 442                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 443                                  BATL_GUARDEDSTORAGE)
 444 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_LBC_BASE | BATU_BL_128K \
 445                                  | BATU_VS | BATU_VP)
 446 #define CONFIG_SYS_IBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 447                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 448                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 449 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 450
 451 /* if CONFIG_PCI:
 452  * BAT2         PCIE1 and PCIE1 MEM
 453  * if CONFIG_RIO
 454  * BAT2         Rapidio Memory
 455  */
 456 #ifdef CONFIG_PCI
 457 #define CONFIG_PCI_INDIRECT_BRIDGE
 458 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 459                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 460                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 461                                  | BATL_GUARDEDSTORAGE)
 462 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \
 463                                  | BATU_VS | BATU_VP)
 464 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 465                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 466                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 467 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 468 #else /* CONFIG_RIO */
 469 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 470                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 471                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 472                                  BATL_GUARDEDSTORAGE)
 473 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \
 474                                  | BATU_VS | BATU_VP)
 475 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 476                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 477                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 478 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 479 #endif
 480
 481 /*
 482  * BAT3         CCSR Space
 483  */
 484 #define CONFIG_SYS_DBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 485                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 486                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 487                                  | BATL_GUARDEDSTORAGE)
 488 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
 489                                  | BATU_VP)
 490 #define CONFIG_SYS_IBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 491                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 492                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 493 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 494
 495 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 496 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 497                                        | BATL_PP_RW | BATL_CACHEINHIBIT \
 498                                        | BATL_GUARDEDSTORAGE)
 499 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
 500                                        | BATU_BL_1M | BATU_VS | BATU_VP)
 501 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 502                                        | BATL_PP_RW | BATL_CACHEINHIBIT)
 503 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
 504 #endif
 505
 506 /*
 507  * BAT4         PCIE1_IO and PCIE2_IO
 508  */
 509 #define CONFIG_SYS_DBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 510                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 511                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 512                                  | BATL_GUARDEDSTORAGE)
 513 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \
 514                                  | BATU_VS | BATU_VP)
 515 #define CONFIG_SYS_IBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 516                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 517                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 518 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 519
 520 /*
 521  * BAT5         Init RAM for stack in the CPU DCache (no backing memory)
 522  */
 523 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 524 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 525 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 526 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 527
 528 /*
 529  * BAT6         FLASH
 530  */
 531 #define CONFIG_SYS_DBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 532                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 533                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 534                                  | BATL_GUARDEDSTORAGE)
 535 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \
 536                                  | BATU_VP)
 537 #define CONFIG_SYS_IBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 538                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 539                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 540 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 541
 542 /* Map the last 1M of flash where we're running from reset */
 543 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 544                                  | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 545 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 546 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 547                                  | BATL_MEMCOHERENCE)
 548 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 549
 550 /*
 551  * BAT7         FREE - used later for tmp mappings
 552  */
 553 #define CONFIG_SYS_DBAT7L 0x00000000
 554 #define CONFIG_SYS_DBAT7U 0x00000000
 555 #define CONFIG_SYS_IBAT7L 0x00000000
 556 #define CONFIG_SYS_IBAT7U 0x00000000
 557
 558 /*
 559  * Environment
 560  */
 561 #ifndef CONFIG_SYS_RAMBOOT
 562     #define CONFIG_ENV_ADDR             \
 563                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 564     #define CONFIG_ENV_SECT_SIZE                0x10000 /* 64K(one sector) for env */
 565 #else
 566     #define CONFIG_ENV_ADDR             (CONFIG_SYS_MONITOR_BASE - 0x1000)
 567 #endif
 568 #define CONFIG_ENV_SIZE         0x2000
 569
 570 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 571 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 572
 573 /*
 574  * BOOTP options
 575  */
 576 #define CONFIG_BOOTP_BOOTFILESIZE
 577 #define CONFIG_BOOTP_BOOTPATH
 578 #define CONFIG_BOOTP_GATEWAY
 579 #define CONFIG_BOOTP_HOSTNAME
 580
 581 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 582
 583 /*
 584  * Miscellaneous configurable options
 585  */
 586 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 587 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 588 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 589
 590 /*
 591  * For booting Linux, the board info and command line data
 592  * have to be in the first 8 MB of memory, since this is
 593  * the maximum mapped by the Linux kernel during initialization.
 594  */
 595 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Initial Memory map for Linux*/
 596 #define CONFIG_SYS_BOOTM_LEN    (256 << 20)     /* Increase max gunzip size */
 597
 598 #if defined(CONFIG_CMD_KGDB)
 599     #define CONFIG_KGDB_BAUDRATE        230400  /* speed to run kgdb serial port */
 600 #endif
 601
 602 /*
 603  * Environment Configuration
 604  */
 605
 606 #define CONFIG_HAS_ETH0         1
 607 #define CONFIG_HAS_ETH1         1
 608 #define CONFIG_HAS_ETH2         1
 609 #define CONFIG_HAS_ETH3         1
 610
 611 #define CONFIG_IPADDR           192.168.1.100
 612
 613 #define CONFIG_HOSTNAME         unknown
 614 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 615 #define CONFIG_BOOTFILE         "uImage"
 616 #define CONFIG_UBOOTPATH        u-boot.bin      /* U-Boot image on TFTP server */
 617
 618 #define CONFIG_SERVERIP         192.168.1.1
 619 #define CONFIG_GATEWAYIP        192.168.1.1
 620 #define CONFIG_NETMASK          255.255.255.0
 621
 622 /* default location for tftp and bootm */
 623 #define CONFIG_LOADADDR         0x10000000
 624
 625 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 626         "netdev=eth0\0"                                                 \
 627         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 628         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 629                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 630                         " +$filesize; " \
 631                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 632                         " +$filesize; " \
 633                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 634                         " $filesize; "  \
 635                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 636                         " +$filesize; " \
 637                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 638                         " $filesize\0"  \
 639         "consoledev=ttyS0\0"                                            \
 640         "ramdiskaddr=0x18000000\0"                                              \
 641         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 642         "fdtaddr=0x17c00000\0"                                          \
 643         "fdtfile=mpc8641_hpcn.dtb\0"                                    \
 644         "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0"                        \
 645         "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
 646         "maxcpus=2"
 647
 648 #define CONFIG_NFSBOOTCOMMAND                                           \
 649         "setenv bootargs root=/dev/nfs rw "                             \
 650               "nfsroot=$serverip:$rootpath "                            \
 651               "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 652               "console=$consoledev,$baudrate $othbootargs;"             \
 653         "tftp $loadaddr $bootfile;"                                     \
 654         "tftp $fdtaddr $fdtfile;"                                       \
 655         "bootm $loadaddr - $fdtaddr"
 656
 657 #define CONFIG_RAMBOOTCOMMAND                                           \
 658         "setenv bootargs root=/dev/ram rw "                             \
 659               "console=$consoledev,$baudrate $othbootargs;"             \
 660         "tftp $ramdiskaddr $ramdiskfile;"                               \
 661         "tftp $loadaddr $bootfile;"                                     \
 662         "tftp $fdtaddr $fdtfile;"                                       \
 663         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 664
 665 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 666
 667 #endif  /* __CONFIG_H */