include/configs/MPC8641HPCN.h

   1 /*
   2  * Copyright 2006, 2010-2011 Freescale Semiconductor.
   3  *
   4  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * MPC8641HPCN board configuration file
  11  *
  12  * Make sure you change the MAC address and other network params first,
  13  * search for CONFIG_SERVERIP, etc. in this file.
  14  */
  15
  16 #ifndef __CONFIG_H
  17 #define __CONFIG_H
  18
  19 #define CONFIG_SYS_GENERIC_BOARD
  20 #define CONFIG_DISPLAY_BOARDINFO
  21
  22 /* High Level Configuration Options */
  23 #define CONFIG_MPC8641          1       /* MPC8641 specific */
  24 #define CONFIG_MPC8641HPCN      1       /* MPC8641HPCN board specific */
  25 #define CONFIG_MP               1       /* support multiple processors */
  26 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  27 /*#define CONFIG_PHYS_64BIT     1*/     /* Place devices in 36-bit space */
  28 #define CONFIG_ADDR_MAP         1       /* Use addr map */
  29
  30 /*
  31  * default CCSRBAR is at 0xff700000
  32  * assume U-Boot is less than 0.5MB
  33  */
  34 #define CONFIG_SYS_TEXT_BASE    0xeff00000
  35
  36 #ifdef RUN_DIAG
  37 #define CONFIG_SYS_DIAG_ADDR         CONFIG_SYS_FLASH_BASE
  38 #endif
  39
  40 /*
  41  * virtual address to be used for temporary mappings.  There
  42  * should be 128k free at this VA.
  43  */
  44 #define CONFIG_SYS_SCRATCH_VA   0xe0000000
  45
  46 #define CONFIG_SYS_SRIO
  47 #define CONFIG_SRIO1                    /* SRIO port 1 */
  48
  49 #define CONFIG_PCI              1       /* Enable PCI/PCIE */
  50 #define CONFIG_PCIE1            1       /* PCIE controler 1 (ULI bridge) */
  51 #define CONFIG_PCIE2            1       /* PCIE controler 2 (slot) */
  52 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  53 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  54 #define CONFIG_FSL_LAW          1       /* Use common FSL law init code */
  55
  56 #define CONFIG_TSEC_ENET                /* tsec ethernet support */
  57 #define CONFIG_ENV_OVERWRITE
  58
  59 #define CONFIG_BAT_RW           1       /* Use common BAT rw code */
  60 #define CONFIG_HIGH_BATS        1       /* High BATs supported and enabled */
  61 #define CONFIG_SYS_NUM_ADDR_MAP 8       /* Number of addr map slots = 8 dbats */
  62
  63 #define CONFIG_ALTIVEC          1
  64
  65 /*
  66  * L2CR setup -- make sure this is right for your board!
  67  */
  68 #define CONFIG_SYS_L2
  69 #define L2_INIT         0
  70 #define L2_ENABLE       (L2CR_L2E)
  71
  72 #ifndef CONFIG_SYS_CLK_FREQ
  73 #ifndef __ASSEMBLY__
  74 extern unsigned long get_board_sys_clk(unsigned long dummy);
  75 #endif
  76 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  77 #endif
  78
  79 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  80 #define CONFIG_SYS_MEMTEST_END          0x00400000
  81
  82 /*
  83  * With the exception of PCI Memory and Rapid IO, most devices will simply
  84  * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
  85  * when 36-bit is enabled.  When 36-bit is not enabled, these bits are 0.
  86  */
  87 #ifdef CONFIG_PHYS_64BIT
  88 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f
  89 #else
  90 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000
  91 #endif
  92
  93 /*
  94  * Base addresses -- Note these are effective addresses where the
  95  * actual resources get mapped (not physical addresses)
  96  */
  97 #define CONFIG_SYS_CCSRBAR_DEFAULT      0xff700000      /* CCSRBAR Default */
  98 #define CONFIG_SYS_CCSRBAR              0xffe00000      /* relocated CCSRBAR */
  99 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 100
 101 /* Physical addresses */
 102 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
 103 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    CONFIG_SYS_PHYS_ADDR_HIGH
 104 #define CONFIG_SYS_CCSRBAR_PHYS \
 105         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 106                             CONFIG_SYS_CCSRBAR_PHYS_HIGH)
 107
 108 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */
 109
 110 /*
 111  * DDR Setup
 112  */
 113 #define CONFIG_SYS_FSL_DDR2
 114 #undef CONFIG_FSL_DDR_INTERACTIVE
 115 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
 116 #define CONFIG_DDR_SPD
 117
 118 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
 119 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
 120
 121 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
 122 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 123 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
 124 #define CONFIG_VERY_BIG_RAM
 125
 126 #define CONFIG_NUM_DDR_CONTROLLERS      2
 127 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 128 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 129
 130 /*
 131  * I2C addresses of SPD EEPROMs
 132  */
 133 #define SPD_EEPROM_ADDRESS1     0x51    /* CTLR 0 DIMM 0 */
 134 #define SPD_EEPROM_ADDRESS2     0x52    /* CTLR 0 DIMM 1 */
 135 #define SPD_EEPROM_ADDRESS3     0x53    /* CTLR 1 DIMM 0 */
 136 #define SPD_EEPROM_ADDRESS4     0x54    /* CTLR 1 DIMM 1 */
 137
 138
 139 /*
 140  * These are used when DDR doesn't use SPD.
 141  */
 142 #define CONFIG_SYS_SDRAM_SIZE           256             /* DDR is 256MB */
 143 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
 144 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80010102      /* Enable, no interleaving */
 145 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 146 #define CONFIG_SYS_DDR_TIMING_0 0x00260802
 147 #define CONFIG_SYS_DDR_TIMING_1 0x39357322
 148 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
 149 #define CONFIG_SYS_DDR_MODE_1           0x00480432
 150 #define CONFIG_SYS_DDR_MODE_2           0x00000000
 151 #define CONFIG_SYS_DDR_INTERVAL 0x06090100
 152 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 153 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
 154 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
 155 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 156 #define CONFIG_SYS_DDR_CONTROL          0xe3008000      /* Type = DDR2 */
 157 #define CONFIG_SYS_DDR_CONTROL2 0x04400000
 158
 159 #define CONFIG_ID_EEPROM
 160 #define CONFIG_SYS_I2C_EEPROM_NXID
 161 #define CONFIG_ID_EEPROM
 162 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 163 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 164
 165 #define CONFIG_SYS_FLASH_BASE           0xef800000     /* start of FLASH 8M */
 166 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW  CONFIG_SYS_FLASH_BASE
 167 #define CONFIG_SYS_FLASH_BASE_PHYS \
 168         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 169                             CONFIG_SYS_PHYS_ADDR_HIGH)
 170
 171 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
 172
 173 #define CONFIG_SYS_BR0_PRELIM   (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 174                                  | 0x00001001)  /* port size 16bit */
 175 #define CONFIG_SYS_OR0_PRELIM   0xff806ff7      /* 8MB Boot Flash area*/
 176
 177 #define CONFIG_SYS_BR2_PRELIM   (BR_PHYS_ADDR(CF_BASE_PHYS)             \
 178                                  | 0x00001001)  /* port size 16bit */
 179 #define CONFIG_SYS_OR2_PRELIM   0xffffeff7      /* 32k Compact Flash */
 180
 181 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(PIXIS_BASE_PHYS)  \
 182                                  | 0x00000801) /* port size 8bit */
 183 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32k PIXIS area*/
 184
 185 /*
 186  * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
 187  * The PIXIS and CF by themselves aren't large enough to take up the 128k
 188  * required for the smallest BAT mapping, so there's a 64k hole.
 189  */
 190 #define CONFIG_SYS_LBC_BASE             0xffde0000
 191 #define CONFIG_SYS_LBC_BASE_PHYS_LOW    CONFIG_SYS_LBC_BASE
 192
 193 #define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
 194 #define PIXIS_BASE              (CONFIG_SYS_LBC_BASE + 0x00010000)
 195 #define PIXIS_BASE_PHYS_LOW     (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000)
 196 #define PIXIS_BASE_PHYS         PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \
 197                                                     CONFIG_SYS_PHYS_ADDR_HIGH)
 198 #define PIXIS_SIZE              0x00008000      /* 32k */
 199 #define PIXIS_ID                0x0     /* Board ID at offset 0 */
 200 #define PIXIS_VER               0x1     /* Board version at offset 1 */
 201 #define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
 202 #define PIXIS_RST               0x4     /* PIXIS Reset Control register */
 203 #define PIXIS_AUX               0x6     /* PIXIS Auxiliary register; Scratch register */
 204 #define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
 205 #define PIXIS_VCTL              0x10    /* VELA Control Register */
 206 #define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
 207 #define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
 208 #define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
 209 #define PIXIS_VBOOT_FMAP        0x80    /* VBOOT - CFG_FLASHMAP */
 210 #define PIXIS_VBOOT_FBANK       0x40    /* VBOOT - CFG_FLASHBANK */
 211 #define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
 212 #define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
 213 #define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
 214 #define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
 215 #define CONFIG_SYS_PIXIS_VBOOT_MASK     0x40    /* Reset altbank mask*/
 216
 217 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
 218 #define CF_BASE                 (PIXIS_BASE + PIXIS_SIZE)
 219 #define CF_BASE_PHYS            (PIXIS_BASE_PHYS + PIXIS_SIZE)
 220
 221 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 222 #define CONFIG_SYS_MAX_FLASH_SECT       128             /* sectors per device */
 223
 224 #undef  CONFIG_SYS_FLASH_CHECKSUM
 225 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 226 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 227 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* start of monitor */
 228 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 229
 230 #define CONFIG_FLASH_CFI_DRIVER
 231 #define CONFIG_SYS_FLASH_CFI
 232 #define CONFIG_SYS_FLASH_EMPTY_INFO
 233
 234 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 235 #define CONFIG_SYS_RAMBOOT
 236 #else
 237 #undef  CONFIG_SYS_RAMBOOT
 238 #endif
 239
 240 #if defined(CONFIG_SYS_RAMBOOT)
 241 #undef CONFIG_SPD_EEPROM
 242 #define CONFIG_SYS_SDRAM_SIZE   256
 243 #endif
 244
 245 #undef CONFIG_CLOCKS_IN_MHZ
 246
 247 #define CONFIG_SYS_INIT_RAM_LOCK        1
 248 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 249 #define CONFIG_SYS_INIT_RAM_ADDR        0x0fd00000      /* Initial RAM address */
 250 #else
 251 #define CONFIG_SYS_INIT_RAM_ADDR        0xf8400000      /* Initial RAM address */
 252 #endif
 253 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000          /* Size of used area in RAM */
 254
 255 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 256 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 257
 258 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 kB for Mon */
 259 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)    /* Reserved for malloc */
 260
 261 /* Serial Port */
 262 #define CONFIG_CONS_INDEX     1
 263 #define CONFIG_SYS_NS16550
 264 #define CONFIG_SYS_NS16550_SERIAL
 265 #define CONFIG_SYS_NS16550_REG_SIZE     1
 266 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 267
 268 #define CONFIG_SYS_BAUDRATE_TABLE  \
 269         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 270
 271 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 272 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 273
 274 /* Use the HUSH parser */
 275 #define CONFIG_SYS_HUSH_PARSER
 276
 277 /*
 278  * Pass open firmware flat tree to kernel
 279  */
 280 #define CONFIG_OF_LIBFDT                1
 281 #define CONFIG_OF_BOARD_SETUP           1
 282 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 283
 284 /*
 285  * I2C
 286  */
 287 #define CONFIG_SYS_I2C
 288 #define CONFIG_SYS_I2C_FSL
 289 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 290 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 291 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3100
 292 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 293
 294 /*
 295  * RapidIO MMU
 296  */
 297 #define CONFIG_SYS_SRIO1_MEM_BASE       0x80000000      /* base address */
 298 #ifdef CONFIG_PHYS_64BIT
 299 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   0x00000000
 300 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x0000000c
 301 #else
 302 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW   CONFIG_SYS_SRIO1_MEM_BASE
 303 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH  0x00000000
 304 #endif
 305 #define CONFIG_SYS_SRIO1_MEM_PHYS \
 306         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 307                             CONFIG_SYS_SRIO1_MEM_PHYS_HIGH)
 308 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 128M */
 309
 310 /*
 311  * General PCI
 312  * Addresses are mapped 1-1.
 313  */
 314
 315 #define CONFIG_SYS_PCIE1_NAME           "ULI"
 316 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 317 #ifdef CONFIG_PHYS_64BIT
 318 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 319 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   0x00000000
 320 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x0000000c
 321 #else
 322 #define CONFIG_SYS_PCIE1_MEM_BUS        CONFIG_SYS_PCIE1_MEM_VIRT
 323 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW   CONFIG_SYS_PCIE1_MEM_VIRT
 324 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH  0x00000000
 325 #endif
 326 #define CONFIG_SYS_PCIE1_MEM_PHYS \
 327         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 328                             CONFIG_SYS_PCIE1_MEM_PHYS_HIGH)
 329 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 330 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 331 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
 332 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW    CONFIG_SYS_PCIE1_IO_VIRT
 333 #define CONFIG_SYS_PCIE1_IO_PHYS \
 334         PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 335                             CONFIG_SYS_PHYS_ADDR_HIGH)
 336 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64K */
 337
 338 #ifdef CONFIG_PHYS_64BIT
 339 /*
 340  * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT.
 341  * This will increase the amount of PCI address space available for
 342  * for mapping RAM.
 343  */
 344 #define CONFIG_SYS_PCIE2_MEM_BUS        CONFIG_SYS_PCIE1_MEM_BUS
 345 #else
 346 #define CONFIG_SYS_PCIE2_MEM_BUS        (CONFIG_SYS_PCIE1_MEM_BUS \
 347                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 348 #endif
 349 #define CONFIG_SYS_PCIE2_MEM_VIRT       (CONFIG_SYS_PCIE1_MEM_VIRT \
 350                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 351 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW   (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \
 352                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 353 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH  CONFIG_SYS_PCIE1_MEM_PHYS_HIGH
 354 #define CONFIG_SYS_PCIE2_MEM_PHYS       (CONFIG_SYS_PCIE1_MEM_PHYS \
 355                                          + CONFIG_SYS_PCIE1_MEM_SIZE)
 356 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 357 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 358 #define CONFIG_SYS_PCIE2_IO_VIRT        (CONFIG_SYS_PCIE1_IO_VIRT \
 359                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 360 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW    (CONFIG_SYS_PCIE1_IO_PHYS_LOW \
 361                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 362 #define CONFIG_SYS_PCIE2_IO_PHYS        (CONFIG_SYS_PCIE1_IO_PHYS \
 363                                          + CONFIG_SYS_PCIE1_IO_SIZE)
 364 #define CONFIG_SYS_PCIE2_IO_SIZE        CONFIG_SYS_PCIE1_IO_SIZE
 365
 366 #if defined(CONFIG_PCI)
 367
 368 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 369
 370 #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
 371
 372 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 373
 374 #define CONFIG_RTL8139
 375
 376 #undef CONFIG_EEPRO100
 377 #undef CONFIG_TULIP
 378
 379 /************************************************************
 380  * USB support
 381  ************************************************************/
 382 #define CONFIG_PCI_OHCI                 1
 383 #define CONFIG_USB_OHCI_NEW             1
 384 #define CONFIG_USB_KEYBOARD             1
 385 #define CONFIG_SYS_STDIO_DEREGISTER
 386 #define CONFIG_SYS_USB_EVENT_POLL               1
 387 #define CONFIG_SYS_USB_OHCI_SLOT_NAME           "ohci_pci"
 388 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 389 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 390
 391 /*PCIE video card used*/
 392 #define VIDEO_IO_OFFSET         CONFIG_SYS_PCIE2_IO_VIRT
 393
 394 /*PCI video card used*/
 395 /*#define VIDEO_IO_OFFSET       CONFIG_SYS_PCIE1_IO_VIRT*/
 396
 397 /* video */
 398 #define CONFIG_VIDEO
 399
 400 #if defined(CONFIG_VIDEO)
 401 #define CONFIG_BIOSEMU
 402 #define CONFIG_CFB_CONSOLE
 403 #define CONFIG_VIDEO_SW_CURSOR
 404 #define CONFIG_VGA_AS_SINGLE_DEVICE
 405 #define CONFIG_ATI_RADEON_FB
 406 #define CONFIG_VIDEO_LOGO
 407 /*#define CONFIG_CONSOLE_CURSOR*/
 408 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT
 409 #endif
 410
 411 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 412
 413 #define CONFIG_DOS_PARTITION
 414 #define CONFIG_SCSI_AHCI
 415
 416 #ifdef CONFIG_SCSI_AHCI
 417 #define CONFIG_LIBATA
 418 #define CONFIG_SATA_ULI5288
 419 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     4
 420 #define CONFIG_SYS_SCSI_MAX_LUN 1
 421 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
 422 #define CONFIG_SYS_SCSI_MAXDEVICE       CONFIG_SYS_SCSI_MAX_DEVICE
 423 #endif
 424
 425 #endif  /* CONFIG_PCI */
 426
 427 #if defined(CONFIG_TSEC_ENET)
 428
 429 #define CONFIG_MII              1       /* MII PHY management */
 430
 431 #define CONFIG_TSEC1            1
 432 #define CONFIG_TSEC1_NAME       "eTSEC1"
 433 #define CONFIG_TSEC2            1
 434 #define CONFIG_TSEC2_NAME       "eTSEC2"
 435 #define CONFIG_TSEC3            1
 436 #define CONFIG_TSEC3_NAME       "eTSEC3"
 437 #define CONFIG_TSEC4            1
 438 #define CONFIG_TSEC4_NAME       "eTSEC4"
 439
 440 #define TSEC1_PHY_ADDR          0
 441 #define TSEC2_PHY_ADDR          1
 442 #define TSEC3_PHY_ADDR          2
 443 #define TSEC4_PHY_ADDR          3
 444 #define TSEC1_PHYIDX            0
 445 #define TSEC2_PHYIDX            0
 446 #define TSEC3_PHYIDX            0
 447 #define TSEC4_PHYIDX            0
 448 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 449 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 450 #define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 451 #define TSEC4_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 452
 453 #define CONFIG_ETHPRIME         "eTSEC1"
 454
 455 #endif  /* CONFIG_TSEC_ENET */
 456
 457
 458 #ifdef CONFIG_PHYS_64BIT
 459 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
 460 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
 461
 462 /* Put physical address into the BAT format */
 463 #define BAT_PHYS_ADDR(low, high) \
 464         (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high))
 465 /* Convert high/low pairs to actual 64-bit value */
 466 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32))
 467 #else
 468 /* 32-bit systems just ignore the "high" bits */
 469 #define BAT_PHYS_ADDR(low, high)        (low)
 470 #define PAIRED_PHYS_TO_PHYS(low, high)  (low)
 471 #endif
 472
 473 /*
 474  * BAT0         DDR
 475  */
 476 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 477 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW | BATL_MEMCOHERENCE)
 478
 479 /*
 480  * BAT1         LBC (PIXIS/CF)
 481  */
 482 #define CONFIG_SYS_DBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 483                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 484                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 485                                  BATL_GUARDEDSTORAGE)
 486 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_LBC_BASE | BATU_BL_128K \
 487                                  | BATU_VS | BATU_VP)
 488 #define CONFIG_SYS_IBAT1L       (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \
 489                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 490                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 491 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 492
 493 /* if CONFIG_PCI:
 494  * BAT2         PCIE1 and PCIE1 MEM
 495  * if CONFIG_RIO
 496  * BAT2         Rapidio Memory
 497  */
 498 #ifdef CONFIG_PCI
 499 #define CONFIG_PCI_INDIRECT_BRIDGE
 500 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 501                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 502                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 503                                  | BATL_GUARDEDSTORAGE)
 504 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \
 505                                  | BATU_VS | BATU_VP)
 506 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \
 507                                                CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \
 508                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 509 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 510 #else /* CONFIG_RIO */
 511 #define CONFIG_SYS_DBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 512                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 513                                  | BATL_PP_RW | BATL_CACHEINHIBIT | \
 514                                  BATL_GUARDEDSTORAGE)
 515 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \
 516                                  | BATU_VS | BATU_VP)
 517 #define CONFIG_SYS_IBAT2L       (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \
 518                                                CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \
 519                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 520 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 521 #endif
 522
 523 /*
 524  * BAT3         CCSR Space
 525  */
 526 #define CONFIG_SYS_DBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 527                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 528                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 529                                  | BATL_GUARDEDSTORAGE)
 530 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
 531                                  | BATU_VP)
 532 #define CONFIG_SYS_IBAT3L       (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \
 533                                                CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
 534                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 535 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 536
 537 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 538 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 539                                        | BATL_PP_RW | BATL_CACHEINHIBIT \
 540                                        | BATL_GUARDEDSTORAGE)
 541 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
 542                                        | BATU_BL_1M | BATU_VS | BATU_VP)
 543 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 544                                        | BATL_PP_RW | BATL_CACHEINHIBIT)
 545 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
 546 #endif
 547
 548 /*
 549  * BAT4         PCIE1_IO and PCIE2_IO
 550  */
 551 #define CONFIG_SYS_DBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 552                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 553                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 554                                  | BATL_GUARDEDSTORAGE)
 555 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \
 556                                  | BATU_VS | BATU_VP)
 557 #define CONFIG_SYS_IBAT4L       (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \
 558                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 559                                  | BATL_PP_RW | BATL_CACHEINHIBIT)
 560 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 561
 562 /*
 563  * BAT5         Init RAM for stack in the CPU DCache (no backing memory)
 564  */
 565 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 566 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 567 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 568 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 569
 570 /*
 571  * BAT6         FLASH
 572  */
 573 #define CONFIG_SYS_DBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 574                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 575                                  | BATL_PP_RW | BATL_CACHEINHIBIT \
 576                                  | BATL_GUARDEDSTORAGE)
 577 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \
 578                                  | BATU_VP)
 579 #define CONFIG_SYS_IBAT6L       (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \
 580                                                CONFIG_SYS_PHYS_ADDR_HIGH) \
 581                                  | BATL_PP_RW | BATL_MEMCOHERENCE)
 582 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 583
 584 /* Map the last 1M of flash where we're running from reset */
 585 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 586                                  | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 587 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 588 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 589                                  | BATL_MEMCOHERENCE)
 590 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 591
 592 /*
 593  * BAT7         FREE - used later for tmp mappings
 594  */
 595 #define CONFIG_SYS_DBAT7L 0x00000000
 596 #define CONFIG_SYS_DBAT7U 0x00000000
 597 #define CONFIG_SYS_IBAT7L 0x00000000
 598 #define CONFIG_SYS_IBAT7U 0x00000000
 599
 600 /*
 601  * Environment
 602  */
 603 #ifndef CONFIG_SYS_RAMBOOT
 604     #define CONFIG_ENV_IS_IN_FLASH      1
 605     #define CONFIG_ENV_ADDR             \
 606                         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 607     #define CONFIG_ENV_SECT_SIZE                0x10000 /* 64K(one sector) for env */
 608 #else
 609     #define CONFIG_ENV_IS_NOWHERE       1       /* Store ENV in memory only */
 610     #define CONFIG_ENV_ADDR             (CONFIG_SYS_MONITOR_BASE - 0x1000)
 611 #endif
 612 #define CONFIG_ENV_SIZE         0x2000
 613
 614 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 615 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 616
 617
 618 /*
 619  * BOOTP options
 620  */
 621 #define CONFIG_BOOTP_BOOTFILESIZE
 622 #define CONFIG_BOOTP_BOOTPATH
 623 #define CONFIG_BOOTP_GATEWAY
 624 #define CONFIG_BOOTP_HOSTNAME
 625
 626
 627 /*
 628  * Command line configuration.
 629  */
 630 #define CONFIG_CMD_PING
 631 #define CONFIG_CMD_I2C
 632 #define CONFIG_CMD_REGINFO
 633
 634 #if defined(CONFIG_PCI)
 635     #define CONFIG_CMD_PCI
 636     #define CONFIG_CMD_SCSI
 637     #define CONFIG_CMD_EXT2
 638     #define CONFIG_CMD_USB
 639 #endif
 640
 641
 642 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 643
 644 /*
 645  * Miscellaneous configurable options
 646  */
 647 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 648 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 649 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 650
 651 #if defined(CONFIG_CMD_KGDB)
 652     #define CONFIG_SYS_CBSIZE   1024            /* Console I/O Buffer Size */
 653 #else
 654     #define CONFIG_SYS_CBSIZE   256             /* Console I/O Buffer Size */
 655 #endif
 656
 657 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 658 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 659 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 660
 661 /*
 662  * For booting Linux, the board info and command line data
 663  * have to be in the first 8 MB of memory, since this is
 664  * the maximum mapped by the Linux kernel during initialization.
 665  */
 666 #define CONFIG_SYS_BOOTMAPSZ    (8 << 20)       /* Initial Memory map for Linux*/
 667
 668 #if defined(CONFIG_CMD_KGDB)
 669     #define CONFIG_KGDB_BAUDRATE        230400  /* speed to run kgdb serial port */
 670 #endif
 671
 672 /*
 673  * Environment Configuration
 674  */
 675
 676 #define CONFIG_HAS_ETH0         1
 677 #define CONFIG_HAS_ETH1         1
 678 #define CONFIG_HAS_ETH2         1
 679 #define CONFIG_HAS_ETH3         1
 680
 681 #define CONFIG_IPADDR           192.168.1.100
 682
 683 #define CONFIG_HOSTNAME         unknown
 684 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 685 #define CONFIG_BOOTFILE         "uImage"
 686 #define CONFIG_UBOOTPATH        u-boot.bin      /* U-Boot image on TFTP server */
 687
 688 #define CONFIG_SERVERIP         192.168.1.1
 689 #define CONFIG_GATEWAYIP        192.168.1.1
 690 #define CONFIG_NETMASK          255.255.255.0
 691
 692 /* default location for tftp and bootm */
 693 #define CONFIG_LOADADDR         1000000
 694
 695 #define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
 696 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 697
 698 #define CONFIG_BAUDRATE 115200
 699
 700 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 701         "netdev=eth0\0"                                                 \
 702         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 703         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 704                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 705                         " +$filesize; " \
 706                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 707                         " +$filesize; " \
 708                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 709                         " $filesize; "  \
 710                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 711                         " +$filesize; " \
 712                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 713                         " $filesize\0"  \
 714         "consoledev=ttyS0\0"                                            \
 715         "ramdiskaddr=2000000\0"                                         \
 716         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 717         "fdtaddr=c00000\0"                                              \
 718         "fdtfile=mpc8641_hpcn.dtb\0"                                    \
 719         "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0"                        \
 720         "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
 721         "maxcpus=2"
 722
 723
 724 #define CONFIG_NFSBOOTCOMMAND                                           \
 725         "setenv bootargs root=/dev/nfs rw "                             \
 726               "nfsroot=$serverip:$rootpath "                            \
 727               "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 728               "console=$consoledev,$baudrate $othbootargs;"             \
 729         "tftp $loadaddr $bootfile;"                                     \
 730         "tftp $fdtaddr $fdtfile;"                                       \
 731         "bootm $loadaddr - $fdtaddr"
 732
 733 #define CONFIG_RAMBOOTCOMMAND                                           \
 734         "setenv bootargs root=/dev/ram rw "                             \
 735               "console=$consoledev,$baudrate $othbootargs;"             \
 736         "tftp $ramdiskaddr $ramdiskfile;"                               \
 737         "tftp $loadaddr $bootfile;"                                     \
 738         "tftp $fdtaddr $fdtfile;"                                       \
 739         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 740
 741 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 742
 743 #endif  /* __CONFIG_H */