include/configs/P2041RDB.h

   1 /*
   2  * Copyright 2011-2012 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * P2041 RDB board configuration file
   9  * Also supports P2040 RDB
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 #ifdef CONFIG_RAMBOOT_PBL
  15 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
  16 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
  17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg
  18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg
  19 #endif
  20
  21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  22 /* Set 1M boot space */
  23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  25                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  27 #define CONFIG_SYS_NO_FLASH
  28 #endif
  29
  30 /* High Level Configuration Options */
  31 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  32 #define CONFIG_MP                       /* support multiple processors */
  33
  34 #ifndef CONFIG_SYS_TEXT_BASE
  35 #define CONFIG_SYS_TEXT_BASE    0xeff40000
  36 #endif
  37
  38 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  39 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  40 #endif
  41
  42 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  43 #define CONFIG_SYS_NUM_CPC              CONFIG_NUM_DDR_CONTROLLERS
  44 #define CONFIG_FSL_ELBC                 /* Has Enhanced localbus controller */
  45 #define CONFIG_FSL_CAAM                 /* Enable SEC/CAAM */
  46 #define CONFIG_PCIE1                    /* PCIE controller 1 */
  47 #define CONFIG_PCIE2                    /* PCIE controller 2 */
  48 #define CONFIG_PCIE3                    /* PCIE controller 3 */
  49 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
  50 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  51
  52 #define CONFIG_SYS_SRIO
  53 #define CONFIG_SRIO1                    /* SRIO port 1 */
  54 #define CONFIG_SRIO2                    /* SRIO port 2 */
  55 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  56 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
  57
  58 #define CONFIG_ENV_OVERWRITE
  59
  60 #ifdef CONFIG_SYS_NO_FLASH
  61 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
  62 #define CONFIG_ENV_IS_NOWHERE
  63 #endif
  64 #else
  65 #define CONFIG_FLASH_CFI_DRIVER
  66 #define CONFIG_SYS_FLASH_CFI
  67 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
  68 #endif
  69
  70 #if defined(CONFIG_SPIFLASH)
  71         #define CONFIG_SYS_EXTRA_ENV_RELOC
  72         #define CONFIG_ENV_IS_IN_SPI_FLASH
  73         #define CONFIG_ENV_SPI_BUS              0
  74         #define CONFIG_ENV_SPI_CS               0
  75         #define CONFIG_ENV_SPI_MAX_HZ           10000000
  76         #define CONFIG_ENV_SPI_MODE             0
  77         #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
  78         #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
  79         #define CONFIG_ENV_SECT_SIZE            0x10000
  80 #elif defined(CONFIG_SDCARD)
  81         #define CONFIG_SYS_EXTRA_ENV_RELOC
  82         #define CONFIG_ENV_IS_IN_MMC
  83         #define CONFIG_FSL_FIXED_MMC_LOCATION
  84         #define CONFIG_SYS_MMC_ENV_DEV          0
  85         #define CONFIG_ENV_SIZE                 0x2000
  86         #define CONFIG_ENV_OFFSET               (512 * 1658)
  87 #elif defined(CONFIG_NAND)
  88 #define CONFIG_SYS_EXTRA_ENV_RELOC
  89 #define CONFIG_ENV_IS_IN_NAND
  90 #define CONFIG_ENV_SIZE                 CONFIG_SYS_NAND_BLOCK_SIZE
  91 #define CONFIG_ENV_OFFSET               (7 * CONFIG_SYS_NAND_BLOCK_SIZE)
  92 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
  93 #define CONFIG_ENV_IS_IN_REMOTE
  94 #define CONFIG_ENV_ADDR         0xffe20000
  95 #define CONFIG_ENV_SIZE         0x2000
  96 #elif defined(CONFIG_ENV_IS_NOWHERE)
  97 #define CONFIG_ENV_SIZE         0x2000
  98 #else
  99         #define CONFIG_ENV_IS_IN_FLASH
 100         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE \
 101                         - CONFIG_ENV_SECT_SIZE)
 102         #define CONFIG_ENV_SIZE         0x2000
 103         #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 104 #endif
 105
 106 #ifndef __ASSEMBLY__
 107 unsigned long get_board_sys_clk(unsigned long dummy);
 108 #endif
 109 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
 110
 111 /*
 112  * These can be toggled for performance analysis, otherwise use default.
 113  */
 114 #define CONFIG_SYS_CACHE_STASHING
 115 #define CONFIG_BACKSIDE_L2_CACHE
 116 #define CONFIG_SYS_INIT_L2CSR0          L2CSR0_L2E
 117 #define CONFIG_BTB                      /* toggle branch predition */
 118
 119 #define CONFIG_ENABLE_36BIT_PHYS
 120
 121 #ifdef CONFIG_PHYS_64BIT
 122 #define CONFIG_ADDR_MAP
 123 #define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
 124 #endif
 125
 126 #define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
 127 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 128 #define CONFIG_SYS_MEMTEST_END          0x00400000
 129 #define CONFIG_SYS_ALT_MEMTEST
 130 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
 131
 132 /*
 133  *  Config the L3 Cache as L3 SRAM
 134  */
 135 #define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
 136 #ifdef CONFIG_PHYS_64BIT
 137 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    (0xf00000000ull | \
 138                 CONFIG_RAMBOOT_TEXT_BASE)
 139 #else
 140 #define CONFIG_SYS_INIT_L3_ADDR_PHYS    CONFIG_SYS_INIT_L3_ADDR
 141 #endif
 142 #define CONFIG_SYS_L3_SIZE              (1024 << 10)
 143 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
 144
 145 #ifdef CONFIG_PHYS_64BIT
 146 #define CONFIG_SYS_DCSRBAR              0xf0000000
 147 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
 148 #endif
 149
 150 /* EEPROM */
 151 #define CONFIG_ID_EEPROM
 152 #define CONFIG_SYS_I2C_EEPROM_NXID
 153 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 154 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 155 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 156
 157 /*
 158  * DDR Setup
 159  */
 160 #define CONFIG_VERY_BIG_RAM
 161 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 162 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 163
 164 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 165 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 166
 167 #define CONFIG_DDR_SPD
 168 #define CONFIG_SYS_FSL_DDR3
 169
 170 #define CONFIG_SYS_SPD_BUS_NUM  0
 171 #define SPD_EEPROM_ADDRESS      0x52
 172 #define CONFIG_SYS_SDRAM_SIZE   4096    /* for fixed parameter use */
 173
 174 /*
 175  * Local Bus Definitions
 176  */
 177
 178 /* Set the local bus clock 1/8 of platform clock */
 179 #define CONFIG_SYS_LBC_LCRR             LCRR_CLKDIV_8
 180
 181 /*
 182  * This board doesn't have a promjet connector.
 183  * However, it uses commone corenet board LAW and TLB.
 184  * It is necessary to use the same start address with proper offset.
 185  */
 186 #define CONFIG_SYS_FLASH_BASE           0xe0000000
 187 #ifdef CONFIG_PHYS_64BIT
 188 #define CONFIG_SYS_FLASH_BASE_PHYS      0xfe0000000ull
 189 #else
 190 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 191 #endif
 192
 193 #define CONFIG_SYS_FLASH_BR_PRELIM \
 194                 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
 195                 BR_PS_16 | BR_V)
 196 #define CONFIG_SYS_FLASH_OR_PRELIM \
 197                 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
 198                  | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
 199
 200 #define CONFIG_FSL_CPLD
 201 #define CPLD_BASE               0xffdf0000      /* CPLD registers */
 202 #ifdef CONFIG_PHYS_64BIT
 203 #define CPLD_BASE_PHYS          0xfffdf0000ull
 204 #else
 205 #define CPLD_BASE_PHYS          CPLD_BASE
 206 #endif
 207
 208 #define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V)
 209 #define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32KB but only 4k mapped */
 210
 211 #define PIXIS_LBMAP_SWITCH      7
 212 #define PIXIS_LBMAP_MASK        0xf0
 213 #define PIXIS_LBMAP_SHIFT       4
 214 #define PIXIS_LBMAP_ALTBANK     0x40
 215
 216 #define CONFIG_SYS_FLASH_QUIET_TEST
 217 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 218
 219 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 220 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 221 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000           /* Erase Timeout (ms) */
 222 #define CONFIG_SYS_FLASH_WRITE_TOUT     500             /* Write Timeout (ms) */
 223
 224 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 225
 226 #if defined(CONFIG_RAMBOOT_PBL)
 227 #define CONFIG_SYS_RAMBOOT
 228 #endif
 229
 230 #define CONFIG_NAND_FSL_ELBC
 231 /* Nand Flash */
 232 #ifdef CONFIG_NAND_FSL_ELBC
 233 #define CONFIG_SYS_NAND_BASE            0xffa00000
 234 #ifdef CONFIG_PHYS_64BIT
 235 #define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
 236 #else
 237 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 238 #endif
 239
 240 #define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
 241 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 242 #define CONFIG_CMD_NAND
 243 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
 244
 245 /* NAND flash config */
 246 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 247                                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
 248                                | BR_PS_8               /* Port Size = 8 bit */ \
 249                                | BR_MS_FCM             /* MSEL = FCM */ \
 250                                | BR_V)                 /* valid */
 251 #define CONFIG_SYS_NAND_OR_PRELIM  (0xFFFC0000        /* length 256K */ \
 252                                | OR_FCM_PGS            /* Large Page*/ \
 253                                | OR_FCM_CSCT \
 254                                | OR_FCM_CST \
 255                                | OR_FCM_CHT \
 256                                | OR_FCM_SCY_1 \
 257                                | OR_FCM_TRLX \
 258                                | OR_FCM_EHTR)
 259
 260 #ifdef CONFIG_NAND
 261 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 262 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 263 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 264 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 265 #else
 266 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 267 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 268 #define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 269 #define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 270 #endif
 271 #else
 272 #define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */
 273 #define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */
 274 #endif /* CONFIG_NAND_FSL_ELBC */
 275
 276 #define CONFIG_SYS_FLASH_EMPTY_INFO
 277 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
 278 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000}
 279
 280 #define CONFIG_BOARD_EARLY_INIT_F
 281 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 282 #define CONFIG_MISC_INIT_R
 283
 284 #define CONFIG_HWCONFIG
 285
 286 /* define to use L1 as initial stack */
 287 #define CONFIG_L1_INIT_RAM
 288 #define CONFIG_SYS_INIT_RAM_LOCK
 289 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
 290 #ifdef CONFIG_PHYS_64BIT
 291 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
 292 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
 293 /* The assembler doesn't like typecast */
 294 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 295         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 296           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 297 #else
 298 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
 299 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 300 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 301 #endif
 302 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 303
 304 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 305                                         GENERATED_GBL_DATA_SIZE)
 306 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 307
 308 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 309 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)
 310
 311 /* Serial Port - controlled on board with jumper J8
 312  * open - index 2
 313  * shorted - index 1
 314  */
 315 #define CONFIG_CONS_INDEX       1
 316 #define CONFIG_SYS_NS16550_SERIAL
 317 #define CONFIG_SYS_NS16550_REG_SIZE     1
 318 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 319
 320 #define CONFIG_SYS_BAUDRATE_TABLE       \
 321         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 322
 323 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 324 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 325 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 326 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 327
 328 /* I2C */
 329 #define CONFIG_SYS_I2C
 330 #define CONFIG_SYS_I2C_FSL
 331 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 332 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 333 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
 334 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 335 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 336 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x118100
 337
 338 /*
 339  * RapidIO
 340  */
 341 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 342 #ifdef CONFIG_PHYS_64BIT
 343 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 344 #else
 345 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xa0000000
 346 #endif
 347 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000      /* 256M */
 348
 349 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 350 #ifdef CONFIG_PHYS_64BIT
 351 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 352 #else
 353 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xb0000000
 354 #endif
 355 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000      /* 256M */
 356
 357 /*
 358  * for slave u-boot IMAGE instored in master memory space,
 359  * PHYS must be aligned based on the SIZE
 360  */
 361 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 362 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 363 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000       /* 1M */
 364 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 365 /*
 366  * for slave UCODE and ENV instored in master memory space,
 367  * PHYS must be aligned based on the SIZE
 368  */
 369 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 370 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 371 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000    /* 256K */
 372
 373 /* slave core release by master*/
 374 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 375 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 376
 377 /*
 378  * SRIO_PCIE_BOOT - SLAVE
 379  */
 380 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 381 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 382 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 383                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 384 #endif
 385
 386 /*
 387  * eSPI - Enhanced SPI
 388  */
 389 #define CONFIG_SF_DEFAULT_SPEED         10000000
 390 #define CONFIG_SF_DEFAULT_MODE          0
 391
 392 /*
 393  * General PCI
 394  * Memory space is mapped 1-1, but I/O space must start from 0.
 395  */
 396
 397 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 398 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 399 #ifdef CONFIG_PHYS_64BIT
 400 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 401 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 402 #else
 403 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 404 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 405 #endif
 406 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 407 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 408 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 409 #ifdef CONFIG_PHYS_64BIT
 410 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 411 #else
 412 #define CONFIG_SYS_PCIE1_IO_PHYS        0xf8000000
 413 #endif
 414 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 415
 416 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 417 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 418 #ifdef CONFIG_PHYS_64BIT
 419 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 420 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 421 #else
 422 #define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
 423 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
 424 #endif
 425 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 426 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 427 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 428 #ifdef CONFIG_PHYS_64BIT
 429 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 430 #else
 431 #define CONFIG_SYS_PCIE2_IO_PHYS        0xf8010000
 432 #endif
 433 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 434
 435 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 436 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xc0000000
 437 #ifdef CONFIG_PHYS_64BIT
 438 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 439 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc40000000ull
 440 #else
 441 #define CONFIG_SYS_PCIE3_MEM_BUS        0xc0000000
 442 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc0000000
 443 #endif
 444 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
 445 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 446 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 447 #ifdef CONFIG_PHYS_64BIT
 448 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 449 #else
 450 #define CONFIG_SYS_PCIE3_IO_PHYS        0xf8020000
 451 #endif
 452 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 453
 454 /* Qman/Bman */
 455 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 456 #define CONFIG_SYS_BMAN_NUM_PORTALS     10
 457 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 458 #ifdef CONFIG_PHYS_64BIT
 459 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 460 #else
 461 #define CONFIG_SYS_BMAN_MEM_PHYS        CONFIG_SYS_BMAN_MEM_BASE
 462 #endif
 463 #define CONFIG_SYS_BMAN_MEM_SIZE        0x00200000
 464 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 465 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 466 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 467 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 468 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 469                                         CONFIG_SYS_BMAN_CENA_SIZE)
 470 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 471 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 472 #define CONFIG_SYS_QMAN_NUM_PORTALS     10
 473 #define CONFIG_SYS_QMAN_MEM_BASE        0xf4200000
 474 #ifdef CONFIG_PHYS_64BIT
 475 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff4200000ull
 476 #else
 477 #define CONFIG_SYS_QMAN_MEM_PHYS        CONFIG_SYS_QMAN_MEM_BASE
 478 #endif
 479 #define CONFIG_SYS_QMAN_MEM_SIZE        0x00200000
 480 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 481 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 482 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 483 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 484 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 485                                         CONFIG_SYS_QMAN_CENA_SIZE)
 486 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 487 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 488
 489 #define CONFIG_SYS_DPAA_FMAN
 490 #define CONFIG_SYS_DPAA_PME
 491 /* Default address of microcode for the Linux Fman driver */
 492 #if defined(CONFIG_SPIFLASH)
 493 /*
 494  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 495  * env, so we got 0x110000.
 496  */
 497 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 498 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 499 #elif defined(CONFIG_SDCARD)
 500 /*
 501  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 502  * about 825KB (1650 blocks), Env is stored after the image, and the env size is
 503  * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
 504  */
 505 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 506 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
 507 #elif defined(CONFIG_NAND)
 508 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 509 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE)
 510 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 511 /*
 512  * Slave has no ucode locally, it can fetch this from remote. When implementing
 513  * in two corenet boards, slave's ucode could be stored in master's memory
 514  * space, the address can be mapped from slave TLB->slave LAW->
 515  * slave SRIO or PCIE outbound window->master inbound window->
 516  * master LAW->the ucode address in master's memory space.
 517  */
 518 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 519 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
 520 #else
 521 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 522 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
 523 #endif
 524 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 525 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 526
 527 #ifdef CONFIG_SYS_DPAA_FMAN
 528 #define CONFIG_FMAN_ENET
 529 #define CONFIG_PHYLIB_10G
 530 #define CONFIG_PHY_VITESSE
 531 #define CONFIG_PHY_TERANETICS
 532 #endif
 533
 534 #ifdef CONFIG_PCI
 535 #define CONFIG_PCI_INDIRECT_BRIDGE
 536
 537 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 538 #define CONFIG_DOS_PARTITION
 539 #endif  /* CONFIG_PCI */
 540
 541 /* SATA */
 542 #define CONFIG_FSL_SATA_V2
 543
 544 #ifdef CONFIG_FSL_SATA_V2
 545 #define CONFIG_FSL_SATA
 546 #define CONFIG_LIBATA
 547
 548 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 549 #define CONFIG_SATA1
 550 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 551 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 552 #define CONFIG_SATA2
 553 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 554 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 555
 556 #define CONFIG_LBA48
 557 #define CONFIG_CMD_SATA
 558 #define CONFIG_DOS_PARTITION
 559 #endif
 560
 561 #ifdef CONFIG_FMAN_ENET
 562 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR  0x2
 563 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR  0x3
 564 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR  0x4
 565 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR  0x1
 566 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x0
 567
 568 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
 569 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
 570 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
 571 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
 572
 573 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR  0
 574
 575 #define CONFIG_SYS_TBIPA_VALUE  8
 576 #define CONFIG_MII              /* MII PHY management */
 577 #define CONFIG_ETHPRIME         "FM1@DTSEC1"
 578 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 579 #endif
 580
 581 /*
 582  * Environment
 583  */
 584 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 585 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 586
 587 /*
 588  * Command line configuration.
 589  */
 590 #define CONFIG_CMD_ERRATA
 591 #define CONFIG_CMD_IRQ
 592
 593 #ifdef CONFIG_PCI
 594 #define CONFIG_CMD_PCI
 595 #endif
 596
 597 /*
 598 * USB
 599 */
 600 #define CONFIG_HAS_FSL_DR_USB
 601 #define CONFIG_HAS_FSL_MPH_USB
 602
 603 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
 604 #define CONFIG_USB_EHCI
 605 #define CONFIG_USB_EHCI_FSL
 606 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 607 #endif
 608
 609 #ifdef CONFIG_MMC
 610 #define CONFIG_FSL_ESDHC
 611 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 612 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 613 #define CONFIG_GENERIC_MMC
 614 #define CONFIG_DOS_PARTITION
 615 #endif
 616
 617 /* Hash command with SHA acceleration supported in hardware */
 618 #ifdef CONFIG_FSL_CAAM
 619 #define CONFIG_CMD_HASH
 620 #define CONFIG_SHA_HW_ACCEL
 621 #endif
 622
 623 /*
 624  * Miscellaneous configurable options
 625  */
 626 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 627 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 628 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 629 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 630 #ifdef CONFIG_CMD_KGDB
 631 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 632 #else
 633 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 634 #endif
 635 /* Print Buffer Size */
 636 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 637                                 sizeof(CONFIG_SYS_PROMPT)+16)
 638 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 639 /* Boot Argument Buffer Size */
 640 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 641
 642 /*
 643  * For booting Linux, the board info and command line data
 644  * have to be in the first 64 MB of memory, since this is
 645  * the maximum mapped by the Linux kernel during initialization.
 646  */
 647 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux */
 648 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 649
 650 #ifdef CONFIG_CMD_KGDB
 651 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 652 #endif
 653
 654 /*
 655  * Environment Configuration
 656  */
 657 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 658 #define CONFIG_BOOTFILE         "uImage"
 659 #define CONFIG_UBOOTPATH        u-boot.bin
 660
 661 /* default location for tftp and bootm */
 662 #define CONFIG_LOADADDR         1000000
 663
 664
 665 #define CONFIG_BAUDRATE 115200
 666
 667 #define __USB_PHY_TYPE  utmi
 668
 669 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 670         "hwconfig=fsl_ddr:ctlr_intlv=cacheline,"                \
 671         "bank_intlv=cs0_cs1\0"                                  \
 672         "netdev=eth0\0"                                         \
 673         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 674         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"             \
 675         "tftpflash=tftpboot $loadaddr $uboot && "               \
 676         "protect off $ubootaddr +$filesize && "                 \
 677         "erase $ubootaddr +$filesize && "                       \
 678         "cp.b $loadaddr $ubootaddr $filesize && "               \
 679         "protect on $ubootaddr +$filesize && "                  \
 680         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 681         "consoledev=ttyS0\0"                                    \
 682         "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"                \
 683         "usb_dr_mode=host\0"                                    \
 684         "ramdiskaddr=2000000\0"                                 \
 685         "ramdiskfile=p2041rdb/ramdisk.uboot\0"                  \
 686         "fdtaddr=1e00000\0"                                     \
 687         "fdtfile=p2041rdb/p2041rdb.dtb\0"                       \
 688         "bdev=sda3\0"
 689
 690 #define CONFIG_HDBOOT                                   \
 691         "setenv bootargs root=/dev/$bdev rw "           \
 692         "console=$consoledev,$baudrate $othbootargs;"   \
 693         "tftp $loadaddr $bootfile;"                     \
 694         "tftp $fdtaddr $fdtfile;"                       \
 695         "bootm $loadaddr - $fdtaddr"
 696
 697 #define CONFIG_NFSBOOTCOMMAND                   \
 698         "setenv bootargs root=/dev/nfs rw "     \
 699         "nfsroot=$serverip:$rootpath "          \
 700         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 701         "console=$consoledev,$baudrate $othbootargs;"   \
 702         "tftp $loadaddr $bootfile;"             \
 703         "tftp $fdtaddr $fdtfile;"               \
 704         "bootm $loadaddr - $fdtaddr"
 705
 706 #define CONFIG_RAMBOOTCOMMAND                           \
 707         "setenv bootargs root=/dev/ram rw "             \
 708         "console=$consoledev,$baudrate $othbootargs;"   \
 709         "tftp $ramdiskaddr $ramdiskfile;"               \
 710         "tftp $loadaddr $bootfile;"                     \
 711         "tftp $fdtaddr $fdtfile;"                       \
 712         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 713
 714 #define CONFIG_BOOTCOMMAND              CONFIG_HDBOOT
 715
 716 #include <asm/fsl_secure_boot.h>
 717
 718 #endif  /* __CONFIG_H */