include/configs/PIP405.h

   1 /*
   2  * (C) Copyright 2001
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /***********************************************************
  16  * High Level Configuration Options
  17  * (easy to change)
  18  ***********************************************************/
  19 #define CONFIG_405GP            1       /* This is a PPC405 CPU         */
  20 #define CONFIG_PIP405           1       /* ...on a PIP405 board         */
  21
  22 #define CONFIG_SYS_TEXT_BASE    0xFFF80000
  23
  24 /***********************************************************
  25  * Clock
  26  ***********************************************************/
  27 #define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
  28
  29 /*
  30  * BOOTP options
  31  */
  32 #define CONFIG_BOOTP_BOOTFILESIZE
  33 #define CONFIG_BOOTP_BOOTPATH
  34 #define CONFIG_BOOTP_GATEWAY
  35 #define CONFIG_BOOTP_HOSTNAME
  36
  37 /*
  38  * Command line configuration.
  39  */
  40 #define CONFIG_CMD_IDE
  41 #define CONFIG_CMD_PCI
  42 #define CONFIG_CMD_IRQ
  43 #define CONFIG_CMD_EEPROM
  44 #define CONFIG_CMD_REGINFO
  45 #define CONFIG_CMD_FDC
  46 #define CONFIG_SCSI
  47 #define CONFIG_CMD_DATE
  48 #define CONFIG_CMD_SDRAM
  49 #define CONFIG_CMD_SAVES
  50 #define CONFIG_CMD_BSP
  51
  52 /**************************************************************
  53  * I2C Stuff:
  54  * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address
  55  * 0x53.
  56  * Caution: on the same bus is the SPD (Serial Presens Detect
  57  * EEPROM of the SDRAM
  58  * The Atmel EEPROM uses 16Bit addressing.
  59  ***************************************************************/
  60 #define CONFIG_SYS_I2C
  61 #define CONFIG_SYS_I2C_PPC4XX
  62 #define CONFIG_SYS_I2C_PPC4XX_CH0
  63 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0           50000
  64 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0           0x7F
  65
  66 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x53
  67 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
  68 #define CONFIG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
  69 #define CONFIG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
  70 #define CONFIG_ENV_SIZE            0x800   /* 2 kBytes may be used for env vars */
  71
  72 #undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
  73 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6     /* The Atmel 24C128/256 has     */
  74                                         /* 64 byte page write mode using*/
  75                                         /* last 6 bits of the address   */
  76 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
  77
  78 /***************************************************************
  79  * Definitions for Serial Presence Detect EEPROM address
  80  * (to get SDRAM settings)
  81  ***************************************************************/
  82 #define SPD_EEPROM_ADDRESS      0x50
  83
  84 #define CONFIG_BOARD_EARLY_INIT_F
  85 #define CONFIG_BOARD_EARLY_INIT_R
  86
  87 /**************************************************************
  88  * Environment definitions
  89  **************************************************************/
  90 #define CONFIG_BAUDRATE         9600    /* STD Baudrate */
  91
  92 #define CONFIG_BOOTDELAY        5
  93 /* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
  94 /* #define CONFIG_BOOT_RETRY_TIME       -10     /XXX* feature is available but not enabled */
  95 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check console even if bootdelay = 0 */
  96
  97 #define CONFIG_BOOTCOMMAND      "diskboot 400000 0:1; bootm" /* autoboot command                */
  98 #define CONFIG_BOOTARGS         "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
  99
 100 #define CONFIG_IPADDR           10.0.0.100
 101 #define CONFIG_SERVERIP         10.0.0.1
 102 #define CONFIG_PREBOOT
 103 /***************************************************************
 104  * defines if the console is stored in the environment
 105  ***************************************************************/
 106 #define CONFIG_SYS_CONSOLE_IS_IN_ENV    /* stdin, stdout and stderr are in evironment */
 107 /***************************************************************
 108  * defines if an overwrite_console function exists
 109  *************************************************************/
 110 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 111 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 112 /***************************************************************
 113  * defines if the overwrite_console should be stored in the
 114  * environment
 115  **************************************************************/
 116 #undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
 117
 118 /**************************************************************
 119  * loads config
 120  *************************************************************/
 121 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
 122 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
 123
 124 #define CONFIG_MISC_INIT_R
 125 /***********************************************************
 126  * Miscellaneous configurable options
 127  **********************************************************/
 128 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 129 #if defined(CONFIG_CMD_KGDB)
 130 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
 131 #else
 132 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
 133 #endif
 134 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 135 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 136 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 137
 138 #define CONFIG_SYS_MEMTEST_START        0x0100000       /* memtest works on     */
 139 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 1 ... 12 MB in DRAM  */
 140
 141 #define CONFIG_CONS_INDEX       1       /* Use UART0                    */
 142 #define CONFIG_SYS_NS16550_SERIAL
 143 #define CONFIG_SYS_NS16550_REG_SIZE     1
 144 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
 145
 146 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
 147 #define CONFIG_SYS_BASE_BAUD       691200
 148
 149 /* The following table includes the supported baudrates */
 150 #define CONFIG_SYS_BAUDRATE_TABLE       \
 151         { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 152          57600, 115200, 230400, 460800, 921600 }
 153
 154 #define CONFIG_SYS_LOAD_ADDR            0x400000        /* default load address */
 155 #define CONFIG_SYS_EXTBDINFO            1       /* To use extended board_into (bd_t) */
 156
 157 /*-----------------------------------------------------------------------
 158  * PCI stuff
 159  *-----------------------------------------------------------------------
 160  */
 161 #define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
 162 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 163 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 164
 165 #define CONFIG_PCI                      /* include pci support          */
 166 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
 167 #define CONFIG_PCI_HOST PCI_HOST_FORCE  /* configure as pci-host        */
 168 #define CONFIG_PCI_PNP                  /* pci plug-and-play            */
 169                                         /* resource configuration       */
 170 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000   /* PCI Vendor ID: to-do!!!      */
 171 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000   /* PCI Device ID: to-do!!!      */
 172 #define CONFIG_SYS_PCI_PTM1LA   0x00000000      /* point to sdram               */
 173 #define CONFIG_SYS_PCI_PTM1MS   0x80000001      /* 2GB, enable hard-wired to 1  */
 174 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 175 #define CONFIG_SYS_PCI_PTM2LA   0x00000000      /* disabled                     */
 176 #define CONFIG_SYS_PCI_PTM2MS   0x00000000      /* disabled                     */
 177 #define CONFIG_SYS_PCI_PTM2PCI 0x00000000      /* Host: use this pci address   */
 178
 179 /*-----------------------------------------------------------------------
 180  * Start addresses for the final memory configuration
 181  * (Set up by the startup code)
 182  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 183  */
 184 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 185 #define CONFIG_SYS_FLASH_BASE           0xFFF80000
 186 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 187 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 kB for Monitor   */
 188 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserve 1024 kB for malloc() */
 189
 190 /*
 191  * For booting Linux, the board info and command line data
 192  * have to be in the first 8 MB of memory, since this is
 193  * the maximum mapped by the Linux kernel during initialization.
 194  */
 195 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 196 /*-----------------------------------------------------------------------
 197  * FLASH organization
 198  */
 199 #define CONFIG_SYS_UPDATE_FLASH_SIZE
 200 #define CONFIG_SYS_FLASH_PROTECTION
 201 #define CONFIG_SYS_FLASH_EMPTY_INFO
 202
 203 #define CONFIG_SYS_FLASH_CFI
 204 #define CONFIG_FLASH_CFI_DRIVER
 205
 206 #define CONFIG_FLASH_SHOW_PROGRESS      45
 207
 208 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 209 #define CONFIG_SYS_MAX_FLASH_SECT       256
 210
 211 /*
 212  * Init Memory Controller:
 213  */
 214 #define FLASH_MAX_SIZE          0x00800000              /* 8MByte max */
 215 #define FLASH_BASE_PRELIM       0xFF800000  /* open the flash CS */
 216 /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
 217 #define FLASH_SIZE_PRELIM        3  /* maximal flash FLASH size bank #0 */
 218
 219 #define CONFIG_BOARD_EARLY_INIT_F
 220
 221 /* Configuration Port location */
 222 #define CONFIG_PORT_ADDR        0xF4000000
 223 #define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
 224
 225 /*-----------------------------------------------------------------------
 226  * Definitions for initial stack pointer and data area (in On Chip SRAM)
 227  */
 228 #define CONFIG_SYS_TEMP_STACK_OCM       1
 229 #define CONFIG_SYS_OCM_DATA_ADDR        0xF0000000
 230 #define CONFIG_SYS_OCM_DATA_SIZE        0x1000
 231 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_OCM_DATA_ADDR        /* inside of On Chip SRAM    */
 232 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_OCM_DATA_SIZE        /* Size of On Chip SRAM        */
 233 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 234 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 235
 236 /***********************************************************************
 237  * External peripheral base address
 238  ***********************************************************************/
 239 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
 240
 241 /***********************************************************************
 242  * Last Stage Init
 243  ***********************************************************************/
 244 #define CONFIG_LAST_STAGE_INIT
 245 /************************************************************
 246  * Ethernet Stuff
 247  ***********************************************************/
 248 #define CONFIG_PPC4xx_EMAC
 249 #define CONFIG_MII              1       /* MII PHY management           */
 250 #define CONFIG_PHY_ADDR         1       /* PHY address                  */
 251 /************************************************************
 252  * RTC
 253  ***********************************************************/
 254 #define CONFIG_RTC_MC146818
 255 #undef CONFIG_WATCHDOG                  /* watchdog disabled            */
 256
 257 /************************************************************
 258  * IDE/ATA stuff
 259  ************************************************************/
 260 #define CONFIG_SYS_IDE_MAXBUS           2   /* max. 2 IDE busses        */
 261 #define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
 262
 263 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */
 264 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x01F0  /* ide0 offste */
 265 #define CONFIG_SYS_ATA_IDE1_OFFSET      0x0170  /* ide1 offset */
 266 #define CONFIG_SYS_ATA_DATA_OFFSET      0       /* data reg offset      */
 267 #define CONFIG_SYS_ATA_REG_OFFSET       0       /* reg offset */
 268 #define CONFIG_SYS_ATA_ALT_OFFSET       0x200   /* alternate register offset */
 269
 270 #undef  CONFIG_IDE_8xx_DIRECT           /* no pcmcia interface required */
 271 #undef  CONFIG_IDE_LED                  /* no led for ide supported     */
 272 #define CONFIG_IDE_RESET                /* reset for ide supported...   */
 273 #define CONFIG_IDE_RESET_ROUTINE        /* with a special reset function */
 274 #define CONFIG_SUPPORT_VFAT
 275
 276 /************************************************************
 277  * ATAPI support (experimental)
 278  ************************************************************/
 279 #define CONFIG_ATAPI                    /* enable ATAPI Support */
 280
 281 /************************************************************
 282  * SCSI support (experimental) only SYM53C8xx supported
 283  ************************************************************/
 284 #define CONFIG_SCSI_SYM53C8XX
 285 #define CONFIG_SYS_SCSI_MAX_LUN 8       /* number of supported LUNs */
 286 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     7       /* maximum SCSI ID (0..6) */
 287 #define CONFIG_SYS_SCSI_MAX_DEVICE      CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */
 288 #define CONFIG_SYS_SCSI_SPIN_UP_TIME    2
 289
 290 /************************************************************
 291  * Disk-On-Chip configuration
 292  ************************************************************/
 293 #define CONFIG_SYS_MAX_DOC_DEVICE       1       /* Max number of DOC devices            */
 294 #define CONFIG_SYS_DOC_SHORT_TIMEOUT
 295 #define CONFIG_SYS_DOC_SUPPORT_2000
 296 #define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
 297
 298 /************************************************************
 299  * DISK Partition support
 300  ************************************************************/
 301 #define CONFIG_DOS_PARTITION
 302 #define CONFIG_MAC_PARTITION
 303 #define CONFIG_ISO_PARTITION /* Experimental */
 304
 305 /************************************************************
 306  * Video support
 307  ************************************************************/
 308 #define CONFIG_VIDEO                    /*To enable video controller support */
 309 #define CONFIG_VIDEO_CT69000
 310 #define CONFIG_CFB_CONSOLE
 311 #define CONFIG_VIDEO_LOGO
 312 #define CONFIG_CONSOLE_EXTRA_INFO
 313 #define CONFIG_VGA_AS_SINGLE_DEVICE
 314 #define CONFIG_VIDEO_SW_CURSOR
 315 #define CONFIG_VIDEO_ONBOARD            /* Video controller is on-board */
 316
 317 /************************************************************
 318  * USB support
 319  ************************************************************/
 320 #define CONFIG_USB_UHCI
 321 #define CONFIG_USB_KEYBOARD
 322 #define CONFIG_USB_STORAGE
 323
 324 /* Enable needed helper functions */
 325 #define CONFIG_SYS_STDIO_DEREGISTER             /* needs stdio_deregister */
 326
 327 /************************************************************
 328  * Debug support
 329  ************************************************************/
 330 #if defined(CONFIG_CMD_KGDB)
 331 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 332 #endif
 333
 334 /************************************************************
 335  * support BZIP2 compression
 336  ************************************************************/
 337 #define CONFIG_BZIP2            1
 338
 339 /************************************************************
 340  * Ident
 341  ************************************************************/
 342 #define VERSION_TAG "released"
 343 #define CONFIG_ISO_STRING "MEV-10066-001"
 344 #define CONFIG_IDENT_STRING "\n(c) 2002 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
 345
 346 #endif  /* __CONFIG_H */