include/configs/PLU405.h

   1 /*
   2  * (C) Copyright 2001-2003
   3  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
   4  *
   5  * See file CREDITS for list of people who contributed to this
   6  * project.
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License as
  10  * published by the Free Software Foundation; either version 2 of
  11  * the License, or (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  21  * MA 02111-1307 USA
  22  */
  23
  24 /*
  25  * board/config.h - configuration options, board specific
  26  */
  27
  28 #ifndef __CONFIG_H
  29 #define __CONFIG_H
  30
  31 /*
  32  * High Level Configuration Options
  33  * (easy to change)
  34  */
  35
  36 #define CONFIG_405EP            1       /* This is a PPC405 CPU         */
  37 #define CONFIG_4xx              1       /* ...member of PPC4xx family   */
  38 #define CONFIG_PLU405           1       /* ...on a PLU405 board         */
  39
  40 #define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()    */
  41 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
  42
  43 #define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */
  44
  45 #define CONFIG_BAUDRATE         9600
  46
  47 #undef  CONFIG_BOOTARGS
  48 #undef  CONFIG_BOOTCOMMAND
  49
  50 #define CONFIG_PREBOOT                  /* enable preboot variable      */
  51
  52 #define CFG_LOADS_BAUD_CHANGE   1       /* allow baudrate change        */
  53
  54 #define CONFIG_NET_MULTI        1
  55 #undef  CONFIG_HAS_ETH1
  56
  57 #define CONFIG_MII              1       /* MII PHY management           */
  58 #define CONFIG_PHY_ADDR         0       /* PHY address                  */
  59 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
  60 #define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
  61
  62 #define CONFIG_PHY_CLK_FREQ     EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
  63
  64 #define CONFIG_COMMANDS       ( CONFIG_CMD_DFL  | \
  65                                 CFG_CMD_DHCP    | \
  66                                 CFG_CMD_PCI     | \
  67                                 CFG_CMD_IRQ     | \
  68                                 CFG_CMD_IDE     | \
  69                                 CFG_CMD_FAT     | \
  70                                 CFG_CMD_ELF     | \
  71                                 CFG_CMD_NAND    | \
  72                                 CFG_CMD_DATE    | \
  73                                 CFG_CMD_I2C     | \
  74                                 CFG_CMD_MII     | \
  75                                 CFG_CMD_PING    | \
  76                                 CFG_CMD_EEPROM  )
  77
  78 #define CONFIG_MAC_PARTITION
  79 #define CONFIG_DOS_PARTITION
  80
  81 #define CONFIG_SUPPORT_VFAT
  82
  83 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
  84 #define CONFIG_AUTO_UPDATE_SHOW 1       /* use board show routine       */
  85
  86 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
  87 #include <cmd_confdefs.h>
  88
  89 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  90
  91 #define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
  92 #define CFG_RTC_REG_BASE_ADDR    0xF0000500 /* RTC Base Address         */
  93
  94 #define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */
  95
  96 /*
  97  * Miscellaneous configurable options
  98  */
  99 #define CFG_LONGHELP                    /* undef to save memory         */
 100 #define CFG_PROMPT      "=> "           /* Monitor Command Prompt       */
 101
 102 #undef  CFG_HUSH_PARSER                 /* use "hush" command parser    */
 103 #ifdef  CFG_HUSH_PARSER
 104 #define CFG_PROMPT_HUSH_PS2     "> "
 105 #endif
 106
 107 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 108 #define CFG_CBSIZE      1024            /* Console I/O Buffer Size      */
 109 #else
 110 #define CFG_CBSIZE      256             /* Console I/O Buffer Size      */
 111 #endif
 112 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 113 #define CFG_MAXARGS     16              /* max number of command args   */
 114 #define CFG_BARGSIZE    CFG_CBSIZE      /* Boot Argument Buffer Size    */
 115
 116 #define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
 117
 118 #define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
 119
 120 #define CONFIG_AUTO_COMPLETE    1       /* add autocompletion support   */
 121
 122 #define CFG_MEMTEST_START       0x0400000       /* memtest works on     */
 123 #define CFG_MEMTEST_END         0x0C00000       /* 4 ... 12 MB in DRAM  */
 124
 125 #undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
 126 #define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
 127 #define CFG_BASE_BAUD       691200
 128 #undef  CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
 129
 130 /* The following table includes the supported baudrates */
 131 #define CFG_BAUDRATE_TABLE      \
 132         { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 133          57600, 115200, 230400, 460800, 921600 }
 134
 135 #define CFG_LOAD_ADDR   0x100000        /* default load address */
 136 #define CFG_EXTBDINFO   1               /* To use extended board_into (bd_t) */
 137
 138 #define CFG_HZ          1000            /* decrementer freq: 1 ms ticks */
 139
 140 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 141 #define CONFIG_BOOTDELAY        3       /* autoboot after 3 seconds     */
 142
 143 /* Only interrupt boot if space is pressed */
 144 /* If a long serial cable is connected but */
 145 /* other end is dead, garbage will be read */
 146 #define CONFIG_AUTOBOOT_KEYED 1
 147 #define CONFIG_AUTOBOOT_PROMPT "Press SPACE to abort autoboot in %d seconds\n"
 148 #undef CONFIG_AUTOBOOT_DELAY_STR
 149 #define CONFIG_AUTOBOOT_STOP_STR " "
 150
 151 #define CONFIG_VERSION_VARIABLE 1       /* include version env variable */
 152
 153 #define CFG_RX_ETH_BUFFER       16      /* use 16 rx buffer on 405 emac */
 154
 155 /*-----------------------------------------------------------------------
 156  * NAND-FLASH stuff
 157  *-----------------------------------------------------------------------
 158  */
 159 #define CFG_NAND_LEGACY
 160
 161 #define CFG_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
 162 #define SECTORSIZE 512
 163
 164 #define ADDR_COLUMN 1
 165 #define ADDR_PAGE 2
 166 #define ADDR_COLUMN_PAGE 3
 167
 168 #define NAND_ChipID_UNKNOWN     0x00
 169 #define NAND_MAX_FLOORS 1
 170 #define NAND_MAX_CHIPS 1
 171
 172 #define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
 173 #define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
 174 #define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
 175 #define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
 176
 177 #define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
 178 #define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
 179 #define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
 180 #define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
 181 #define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
 182 #define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
 183 #define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
 184
 185 #define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
 186 #define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
 187 #define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
 188 #define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
 189
 190 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 191
 192 /*-----------------------------------------------------------------------
 193  * PCI stuff
 194  *-----------------------------------------------------------------------
 195  */
 196 #define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
 197 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 198 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 199
 200 #define CONFIG_PCI                      /* include pci support          */
 201 #define CONFIG_PCI_HOST PCI_HOST_HOST   /* select pci host function     */
 202 #define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
 203                                         /* resource configuration       */
 204
 205 #define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
 206
 207 #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
 208
 209 #define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
 210 #define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
 211 #define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
 212 #define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
 213 #define CFG_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
 214 #define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 215 #define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
 216 #define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
 217 #define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
 218
 219 /*-----------------------------------------------------------------------
 220  * IDE/ATA stuff
 221  *-----------------------------------------------------------------------
 222  */
 223 #undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
 224 #undef  CONFIG_IDE_LED                  /* no led for ide supported     */
 225 #define CONFIG_IDE_RESET        1       /* reset for ide supported      */
 226
 227 #define CFG_IDE_MAXBUS          1               /* max. 1 IDE busses    */
 228 #define CFG_IDE_MAXDEVICE       (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 229
 230 #define CFG_ATA_BASE_ADDR       0xF0100000
 231 #define CFG_ATA_IDE0_OFFSET     0x0000
 232
 233 #define CFG_ATA_DATA_OFFSET     0x0000  /* Offset for data I/O                  */
 234 #define CFG_ATA_REG_OFFSET      0x0000  /* Offset for normal register accesses  */
 235 #define CFG_ATA_ALT_OFFSET      0x0000  /* Offset for alternate registers       */
 236
 237 /*
 238  * For booting Linux, the board info and command line data
 239  * have to be in the first 8 MB of memory, since this is
 240  * the maximum mapped by the Linux kernel during initialization.
 241  */
 242 #define CFG_BOOTMAPSZ           (8 << 20)       /* Initial Memory map for Linux */
 243 /*-----------------------------------------------------------------------
 244  * FLASH organization
 245  */
 246 #define FLASH_BASE0_PRELIM      0xFFC00000      /* FLASH bank #0        */
 247
 248 #define CFG_MAX_FLASH_BANKS     1       /* max number of memory banks           */
 249 #define CFG_MAX_FLASH_SECT      256     /* max number of sectors on one chip    */
 250
 251 #define CFG_FLASH_ERASE_TOUT    120000  /* Timeout for Flash Erase (in ms)      */
 252 #define CFG_FLASH_WRITE_TOUT    1000    /* Timeout for Flash Write (in ms)      */
 253
 254 #define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
 255 #define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
 256 #define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
 257 /*
 258  * The following defines are added for buggy IOP480 byte interface.
 259  * All other boards should use the standard values (CPCI405 etc.)
 260  */
 261 #define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
 262 #define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
 263 #define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
 264
 265 #define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
 266
 267 #if 0 /* test-only */
 268 #define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
 269 #define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
 270 #endif
 271
 272 /*-----------------------------------------------------------------------
 273  * Start addresses for the final memory configuration
 274  * (Set up by the startup code)
 275  * Please note that CFG_SDRAM_BASE _must_ start at 0
 276  */
 277 #define CFG_SDRAM_BASE          0x00000000
 278 #define CFG_FLASH_BASE          0xFFFC0000
 279 #define CFG_MONITOR_BASE        TEXT_BASE
 280 #define CFG_MONITOR_LEN         (256 * 1024)    /* Reserve 256 kB for Monitor   */
 281 #define CFG_MALLOC_LEN          (256 * 1024)    /* Reserve 256 kB for malloc()  */
 282
 283 #if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
 284 # define CFG_RAMBOOT            1
 285 #else
 286 # undef CFG_RAMBOOT
 287 #endif
 288
 289 /*-----------------------------------------------------------------------
 290  * Environment Variable setup
 291  */
 292 #define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
 293 #define CFG_ENV_OFFSET          0x100   /* environment starts at the beginning of the EEPROM */
 294 #define CFG_ENV_SIZE            0x700   /* 2048 bytes may be used for env vars*/
 295                                    /* total size of a CAT24WC16 is 2048 bytes */
 296
 297 #define CFG_NVRAM_BASE_ADDR     0xF0000500              /* NVRAM base address   */
 298 #define CFG_NVRAM_SIZE          242                     /* NVRAM size           */
 299
 300 /*-----------------------------------------------------------------------
 301  * I2C EEPROM (CAT24WC16) for environment
 302  */
 303 #define CONFIG_HARD_I2C                 /* I2c with hardware support */
 304 #define CFG_I2C_SPEED           400000  /* I2C speed and slave address */
 305 #define CFG_I2C_SLAVE           0x7F
 306
 307 #define CFG_I2C_EEPROM_ADDR     0x50    /* EEPROM CAT24WC08             */
 308 #if 1 /* test-only */
 309 /* CAT24WC08/16... */
 310 #define CFG_I2C_EEPROM_ADDR_LEN 1       /* Bytes of address             */
 311 /* mask of address bits that overflow into the "EEPROM chip address"    */
 312 #define CFG_I2C_EEPROM_ADDR_OVERFLOW    0x07
 313 #define CFG_EEPROM_PAGE_WRITE_BITS 4    /* The Catalyst CAT24WC08 has   */
 314                                         /* 16 byte page write mode using*/
 315                                         /* last 4 bits of the address   */
 316 #else
 317 /* CAT24WC32/64... */
 318 #define CFG_I2C_EEPROM_ADDR_LEN 2       /* Bytes of address             */
 319 /* mask of address bits that overflow into the "EEPROM chip address"    */
 320 #define CFG_I2C_EEPROM_ADDR_OVERFLOW    0x01
 321 #define CFG_EEPROM_PAGE_WRITE_BITS 5    /* The Catalyst CAT24WC32 has   */
 322                                         /* 32 byte page write mode using*/
 323                                         /* last 5 bits of the address   */
 324 #endif
 325 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS  10   /* and takes up to 10 msec */
 326 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 327
 328 /*-----------------------------------------------------------------------
 329  * Cache Configuration
 330  */
 331 #define CFG_DCACHE_SIZE         16384   /* For AMCC 405 CPUs, older 405 ppc's   */
 332                                         /* have only 8kB, 16kB is save here     */
 333 #define CFG_CACHELINE_SIZE      32      /* ...                  */
 334 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 335 #define CFG_CACHELINE_SHIFT     5       /* log base 2 of the above value        */
 336 #endif
 337
 338 /*-----------------------------------------------------------------------
 339  * External Bus Controller (EBC) Setup
 340  */
 341
 342 #define CAN_BA          0xF0000000          /* CAN Base Address                 */
 343 #define DUART0_BA       0xF0000400          /* DUART Base Address               */
 344 #define DUART1_BA       0xF0000408          /* DUART Base Address               */
 345 #define RTC_BA          0xF0000500          /* RTC Base Address                 */
 346 #define VGA_BA          0xF1000000          /* Epson VGA Base Address           */
 347 #define CFG_NAND_BASE   0xF4000000          /* NAND FLASH Base Address          */
 348
 349 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
 350 #define CFG_EBC_PB0AP           0x92015480
 351 /*#define CFG_EBC_PB0AP           0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
 352 #define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 353
 354 /* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
 355 #define CFG_EBC_PB1AP           0x92015480
 356 #define CFG_EBC_PB1CR           0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
 357
 358 /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
 359 #define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 360 #define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
 361
 362 /* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization     */
 363 #define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 364 #define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 365
 366 /*-----------------------------------------------------------------------
 367  * FPGA stuff
 368  */
 369
 370 #define CFG_FPGA_BASE_ADDR 0xF0100100       /* FPGA internal Base Address       */
 371
 372 /* FPGA internal regs */
 373 #define CFG_FPGA_CTRL           0x000
 374
 375 /* FPGA Control Reg */
 376 #define CFG_FPGA_CTRL_CF_RESET  0x0001
 377 #define CFG_FPGA_CTRL_WDI       0x0002
 378 #define CFG_FPGA_CTRL_PS2_RESET 0x0020
 379
 380 #define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
 381 #define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S50E*/
 382
 383 /* FPGA program pin configuration */
 384 #define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
 385 #define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
 386 #define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
 387 #define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
 388 #define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
 389
 390 /*-----------------------------------------------------------------------
 391  * Definitions for initial stack pointer and data area (in data cache)
 392  */
 393 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
 394 #define CFG_TEMP_STACK_OCM        1
 395
 396 /* On Chip Memory location */
 397 #define CFG_OCM_DATA_ADDR       0xF8000000
 398 #define CFG_OCM_DATA_SIZE       0x1000
 399 #define CFG_INIT_RAM_ADDR       CFG_OCM_DATA_ADDR /* inside of SDRAM            */
 400 #define CFG_INIT_RAM_END        CFG_OCM_DATA_SIZE /* End of used area in RAM    */
 401
 402 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 403 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 404 #define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
 405
 406 /*-----------------------------------------------------------------------
 407  * Definitions for GPIO setup (PPC405EP specific)
 408  *
 409  * GPIO0[0]     - External Bus Controller BLAST output
 410  * GPIO0[1-9]   - Instruction trace outputs -> GPIO
 411  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 412  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 413  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 414  * GPIO0[24-27] - UART0 control signal inputs/outputs
 415  * GPIO0[28-29] - UART1 data signal input/output
 416  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 417  */
 418 #define CFG_GPIO0_OSRH          0x40000550
 419 #define CFG_GPIO0_OSRL          0x00000110
 420 #define CFG_GPIO0_ISR1H         0x00000000
 421 #define CFG_GPIO0_ISR1L         0x15555445
 422 #define CFG_GPIO0_TSRH          0x00000000
 423 #define CFG_GPIO0_TSRL          0x00000000
 424 #define CFG_GPIO0_TCR           0xF7FE0014
 425
 426 #define CFG_DUART_RST           (0x80000000 >> 14)
 427
 428 /*
 429  * Internal Definitions
 430  *
 431  * Boot Flags
 432  */
 433 #define BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH     */
 434 #define BOOTFLAG_WARM   0x02            /* Software reboot                      */
 435
 436 /*
 437  * Default speed selection (cpu_plb_opb_ebc) in mhz.
 438  * This value will be set if iic boot eprom is disabled.
 439  */
 440 #if 0
 441 #define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
 442 #define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
 443 #endif
 444 #if 0
 445 #define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
 446 #define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
 447 #endif
 448 #if 1
 449 #define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
 450 #define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
 451 #endif
 452
 453 #endif  /* __CONFIG_H */