include/configs/PLU405.h

   1 /*
   2  * (C) Copyright 2001-2003
   3  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /*
  16  * High Level Configuration Options
  17  * (easy to change)
  18  */
  19
  20 #define CONFIG_405EP            1       /* This is a PPC405 CPU         */
  21 #define CONFIG_PLU405           1       /* ...on a PLU405 board         */
  22
  23 #define CONFIG_SYS_TEXT_BASE    0xFFF80000
  24 #define CONFIG_SYS_GENERIC_BOARD
  25 #define CONFIG_DISPLAY_BOARDINFO
  26
  27 #define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()    */
  28 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
  29
  30 #define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */
  31
  32 #define CONFIG_BAUDRATE         9600
  33
  34 #undef  CONFIG_BOOTARGS
  35 #undef  CONFIG_BOOTCOMMAND
  36
  37 #define CONFIG_PREBOOT                  /* enable preboot variable      */
  38
  39 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
  40
  41 #undef  CONFIG_HAS_ETH1
  42
  43 #define CONFIG_PPC4xx_EMAC
  44 #define CONFIG_MII              1       /* MII PHY management           */
  45 #define CONFIG_PHY_ADDR         0       /* PHY address                  */
  46 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
  47 #define CONFIG_RESET_PHY_R      1       /* use reset_phy()              */
  48
  49 #define CONFIG_PHY_CLK_FREQ     EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
  50
  51
  52 /*
  53  * BOOTP options
  54  */
  55 #define CONFIG_BOOTP_BOOTFILESIZE
  56 #define CONFIG_BOOTP_BOOTPATH
  57 #define CONFIG_BOOTP_GATEWAY
  58 #define CONFIG_BOOTP_HOSTNAME
  59
  60
  61 /*
  62  * Command line configuration.
  63  */
  64 #include <config_cmd_default.h>
  65
  66 #define CONFIG_CMD_DHCP
  67 #define CONFIG_CMD_PCI
  68 #define CONFIG_CMD_IRQ
  69 #define CONFIG_CMD_IDE
  70 #define CONFIG_CMD_FAT
  71 #define CONFIG_CMD_ELF
  72 #define CONFIG_CMD_NAND
  73 #define CONFIG_CMD_DATE
  74 #define CONFIG_CMD_I2C
  75 #define CONFIG_CMD_MII
  76 #define CONFIG_CMD_PING
  77 #define CONFIG_CMD_EEPROM
  78 #define CONFIG_CMD_USB
  79
  80 #define CONFIG_OF_LIBFDT
  81 #define CONFIG_OF_BOARD_SETUP
  82
  83 #define CONFIG_MAC_PARTITION
  84 #define CONFIG_DOS_PARTITION
  85
  86 #define CONFIG_SUPPORT_VFAT
  87
  88 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  89
  90 #define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
  91 #define CONFIG_SYS_RTC_REG_BASE_ADDR     0xF0000500 /* RTC Base Address         */
  92
  93 #define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */
  94
  95 /*
  96  * Miscellaneous configurable options
  97  */
  98 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
  99
 100 #undef  CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser    */
 101
 102 #if defined(CONFIG_CMD_KGDB)
 103 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
 104 #else
 105 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
 106 #endif
 107 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 108 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 109 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 110
 111 #define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */
 112
 113 #define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup*/
 114
 115 #define CONFIG_AUTO_COMPLETE    1       /* add autocompletion support   */
 116
 117 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 118 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 119
 120 #define CONFIG_CONS_INDEX       1       /* Use UART0                    */
 121 #define CONFIG_SYS_NS16550
 122 #define CONFIG_SYS_NS16550_SERIAL
 123 #define CONFIG_SYS_NS16550_REG_SIZE     1
 124 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
 125
 126 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
 127 #define CONFIG_SYS_BASE_BAUD        691200
 128
 129 /* The following table includes the supported baudrates */
 130 #define CONFIG_SYS_BAUDRATE_TABLE       \
 131         { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 132          57600, 115200, 230400, 460800, 921600 }
 133
 134 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 135 #define CONFIG_SYS_EXTBDINFO    1               /* To use extended board_into (bd_t) */
 136
 137 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 138 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 139 #define CONFIG_BOOTDELAY        3       /* autoboot after 3 seconds     */
 140
 141 #define CONFIG_VERSION_VARIABLE 1       /* include version env variable */
 142
 143 #define CONFIG_SYS_RX_ETH_BUFFER        16      /* use 16 rx buffer on 405 emac */
 144
 145 /*
 146  * NAND-FLASH stuff
 147  */
 148 #define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE}
 149 #define CONFIG_SYS_MAX_NAND_DEVICE      1         /* Max number of NAND devices */
 150 #define NAND_BIG_DELAY_US       25
 151
 152 #define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
 153 #define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
 154 #define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
 155 #define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 156
 157 #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
 158 #define CONFIG_SYS_NAND_QUIET          1
 159
 160 /*
 161  * PCI stuff
 162  */
 163 #define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
 164 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 165 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 166
 167 #define CONFIG_PCI                      /* include pci support          */
 168 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
 169 #define CONFIG_PCI_HOST PCI_HOST_FORCE  /* select pci host function     */
 170 #define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
 171                                         /* resource configuration       */
 172
 173 #define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
 174
 175 #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
 176
 177 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
 178 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
 179 #define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
 180 #define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
 181 #define CONFIG_SYS_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
 182 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 183 #define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
 184 #define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
 185 #define CONFIG_SYS_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */
 186
 187 /*
 188  * IDE/ATA stuff
 189  */
 190 #undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
 191 #undef  CONFIG_IDE_LED                  /* no led for ide supported     */
 192 #define CONFIG_IDE_RESET        1       /* reset for ide supported      */
 193
 194 #define CONFIG_SYS_IDE_MAXBUS           1               /* max. 1 IDE busses    */
 195 /* max. 1 drives per IDE bus */
 196 #define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS*1)
 197
 198 #define CONFIG_SYS_ATA_BASE_ADDR        0xF0100000
 199 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 200
 201 #define CONFIG_SYS_ATA_DATA_OFFSET      0x0000  /* Offset for data I/O */
 202 #define CONFIG_SYS_ATA_REG_OFFSET       0x0000  /* Offset for normal register access */
 203 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0000  /* Offset for alternate registers */
 204
 205 /*
 206  * For booting Linux, the board info and command line data
 207  * have to be in the first 8 MB of memory, since this is
 208  * the maximum mapped by the Linux kernel during initialization.
 209  */
 210 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20) /* Initial Memory map for Linux */
 211
 212 /*
 213  * FLASH organization
 214  */
 215 #define FLASH_BASE0_PRELIM      0xFFC00000 /* FLASH bank #0 */
 216
 217 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
 218 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */
 219
 220 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms) */
 221 #define CONFIG_SYS_FLASH_WRITE_TOUT     1000    /* Timeout for Flash Write (in ms) */
 222
 223 #define CONFIG_SYS_FLASH_WORD_SIZE      unsigned short  /* flash word size (width) */
 224 #define CONFIG_SYS_FLASH_ADDR0          0x5555  /* 1st addr for flash config cycles */
 225 #define CONFIG_SYS_FLASH_ADDR1          0x2AAA  /* 2nd addr for flash config cycles */
 226 /*
 227  * The following defines are added for buggy IOP480 byte interface.
 228  * All other boards should use the standard values (CPCI405 etc.)
 229  */
 230 #define CONFIG_SYS_FLASH_READ0          0x0000  /* 0 is standard */
 231 #define CONFIG_SYS_FLASH_READ1          0x0001  /* 1 is standard */
 232 #define CONFIG_SYS_FLASH_READ2          0x0002  /* 2 is standard */
 233
 234 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* print 'E' for empty sector */
 235
 236 /*
 237  * Start addresses for the final memory configuration
 238  * (Set up by the startup code)
 239  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 240  */
 241 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 242 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_MONITOR_BASE
 243 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 244 #define CONFIG_SYS_MONITOR_LEN          (~(CONFIG_SYS_TEXT_BASE) + 1)
 245 #define CONFIG_SYS_MALLOC_LEN           (1024 << 10)
 246
 247 /*
 248  * Environment Variable setup
 249  */
 250 #define CONFIG_ENV_IS_IN_EEPROM 1       /* use EEPROM for environment vars */
 251 #define CONFIG_ENV_OFFSET               0x100   /* reseve 0x100 bytes for strapping */
 252 #define CONFIG_ENV_SIZE         0x700
 253
 254 /*
 255  * I2C EEPROM (24WC16) for environment
 256  */
 257 #define CONFIG_SYS_I2C
 258 #define CONFIG_SYS_I2C_PPC4XX
 259 #define CONFIG_SYS_I2C_PPC4XX_CH0
 260 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0           400000
 261 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0           0x7F
 262
 263 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM 24WC16 */
 264 #define CONFIG_SYS_EEPROM_WREN         1
 265
 266 /* 24WC16 */
 267 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1        /* Bytes of address             */
 268 /* mask of address bits that overflow into the "EEPROM chip address"    */
 269 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
 270 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4     /* The 24WC16 has   */
 271                                         /* 16 byte page write mode using */
 272                                         /* last 4 bits of the address   */
 273 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */
 274
 275 /*
 276  * External Bus Controller (EBC) Setup
 277  */
 278 #define CAN0_BA         0xF0000000          /* CAN0 Base Address        */
 279 #define CAN1_BA         0xF0000100          /* CAN1 Base Address        */
 280 #define DUART0_BA       0xF0000400          /* DUART Base Address       */
 281 #define DUART1_BA       0xF0000408          /* DUART Base Address       */
 282 #define RTC_BA          0xF0000500          /* RTC Base Address         */
 283 #define VGA_BA          0xF1000000          /* Epson VGA Base Address   */
 284 #define CONFIG_SYS_NAND_BASE    0xF4000000          /* NAND FLASH Base Address  */
 285
 286 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
 287 /* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
 288 #define CONFIG_SYS_EBC_PB0AP            0x92015480
 289 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 290 #define CONFIG_SYS_EBC_PB0CR            0xFFC5A000
 291
 292 /* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
 293 #define CONFIG_SYS_EBC_PB1AP            0x92015480
 294 /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
 295 #define CONFIG_SYS_EBC_PB1CR            0xF4018000
 296
 297 /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
 298 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 299 #define CONFIG_SYS_EBC_PB2AP            0x010053C0
 300 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
 301 #define CONFIG_SYS_EBC_PB2CR            0xF0018000
 302
 303 /* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
 304 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 305 #define CONFIG_SYS_EBC_PB3AP            0x010053C0
 306 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 307 #define CONFIG_SYS_EBC_PB3CR            0xF011A000
 308
 309 /*
 310  * FPGA stuff
 311  */
 312 #define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100        /* FPGA internal Base Address */
 313
 314 /* FPGA internal regs */
 315 #define CONFIG_SYS_FPGA_CTRL            0x000
 316
 317 /* FPGA Control Reg */
 318 #define CONFIG_SYS_FPGA_CTRL_CF_RESET   0x0001
 319 #define CONFIG_SYS_FPGA_CTRL_WDI        0x0002
 320 #define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020
 321
 322 #define CONFIG_SYS_FPGA_SPARTAN2        1           /* using Xilinx Spartan 2 now */
 323 #define CONFIG_SYS_FPGA_MAX_SIZE        128*1024    /* 128kByte is enough for XC2S50E*/
 324
 325 /* FPGA program pin configuration */
 326 #define CONFIG_SYS_FPGA_PRG             0x04000000  /* FPGA program pin (ppc output) */
 327 #define CONFIG_SYS_FPGA_CLK             0x02000000  /* FPGA clk pin (ppc output) */
 328 #define CONFIG_SYS_FPGA_DATA            0x01000000  /* FPGA data pin (ppc output) */
 329 #define CONFIG_SYS_FPGA_INIT            0x00010000  /* FPGA init pin (ppc input) */
 330 #define CONFIG_SYS_FPGA_DONE            0x00008000  /* FPGA done pin (ppc input) */
 331
 332 /*
 333  * Definitions for initial stack pointer and data area (in data cache)
 334  */
 335 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
 336 #define CONFIG_SYS_TEMP_STACK_OCM         1
 337
 338 /* On Chip Memory location */
 339 #define CONFIG_SYS_OCM_DATA_ADDR        0xF8000000
 340 #define CONFIG_SYS_OCM_DATA_SIZE        0x1000
 341 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
 342 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM  */
 343
 344 #define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 345 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 346
 347 /*
 348  * Definitions for GPIO setup (PPC405EP specific)
 349  *
 350  * GPIO0[0]     - External Bus Controller BLAST output
 351  * GPIO0[1-9]   - Instruction trace outputs -> GPIO
 352  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 353  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 354  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 355  * GPIO0[24-27] - UART0 control signal inputs/outputs
 356  * GPIO0[28-29] - UART1 data signal input/output
 357  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 358  */
 359 #define CONFIG_SYS_GPIO0_OSRL           0x00000550
 360 #define CONFIG_SYS_GPIO0_OSRH           0x00000110
 361 #define CONFIG_SYS_GPIO0_ISR1L          0x00000000
 362 #define CONFIG_SYS_GPIO0_ISR1H          0x15555445
 363 #define CONFIG_SYS_GPIO0_TSRL           0x00000000
 364 #define CONFIG_SYS_GPIO0_TSRH           0x00000000
 365 #define CONFIG_SYS_GPIO0_TCR            0x77FE0014
 366
 367 #define CONFIG_SYS_DUART_RST            (0x80000000 >> 14)
 368 #define CONFIG_SYS_EEPROM_WP            (0x80000000 >> 0)
 369
 370 /*
 371  * Default speed selection (cpu_plb_opb_ebc) in MHz.
 372  * This value will be set if iic boot eprom is disabled.
 373  */
 374 #if 1
 375 #define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
 376 #define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
 377 #endif
 378 #if 0
 379 #define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
 380 #define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
 381 #endif
 382 #if 0
 383 #define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
 384 #define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
 385 #endif
 386
 387 /*
 388  * PCI OHCI controller
 389  */
 390 #define CONFIG_USB_OHCI_NEW     1
 391 #define CONFIG_PCI_OHCI         1
 392 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 393 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
 394 #define CONFIG_SYS_USB_OHCI_SLOT_NAME   "ohci_pci"
 395 #define CONFIG_USB_STORAGE      1
 396
 397 /*
 398  * UBI
 399  */
 400 #define CONFIG_CMD_UBI
 401 #define CONFIG_RBTREE
 402 #define CONFIG_MTD_DEVICE
 403 #define CONFIG_MTD_PARTITIONS
 404 #define CONFIG_CMD_MTDPARTS
 405 #define CONFIG_LZO
 406
 407 #endif  /* __CONFIG_H */