include/configs/T208xRDB.h

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #define CONFIG_DISPLAY_BOARDINFO
  15 #define CONFIG_T2080RDB
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_MMC
  18 #define CONFIG_USB_EHCI
  19 #define CONFIG_FSL_SATA_V2
  20
  21 /* High Level Configuration Options */
  22 #define CONFIG_BOOKE
  23 #define CONFIG_E500             /* BOOKE e500 family */
  24 #define CONFIG_E500MC           /* BOOKE e500mc family */
  25 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  26 #define CONFIG_MP               /* support multiple processors */
  27 #define CONFIG_ENABLE_36BIT_PHYS
  28
  29 #ifdef CONFIG_PHYS_64BIT
  30 #define CONFIG_ADDR_MAP 1
  31 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  32 #endif
  33
  34 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  35 #define CONFIG_SYS_NUM_CPC      CONFIG_NUM_DDR_CONTROLLERS
  36 #define CONFIG_FSL_IFC          /* Enable IFC Support */
  37 #define CONFIG_FSL_CAAM         /* Enable SEC/CAAM */
  38 #define CONFIG_FSL_LAW          /* Use common FSL init code */
  39 #define CONFIG_ENV_OVERWRITE
  40
  41 #ifdef CONFIG_RAMBOOT_PBL
  42 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  43 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg
  44
  45 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
  46 #define CONFIG_SPL_SERIAL_SUPPORT
  47 #define CONFIG_SPL_FLUSH_IMAGE
  48 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  49 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  50 #define CONFIG_SYS_TEXT_BASE            0x00201000
  51 #define CONFIG_SPL_TEXT_BASE            0xFFFD8000
  52 #define CONFIG_SPL_PAD_TO               0x40000
  53 #define CONFIG_SPL_MAX_SIZE             0x28000
  54 #define RESET_VECTOR_OFFSET             0x27FFC
  55 #define BOOT_PAGE_OFFSET                0x27000
  56 #ifdef CONFIG_SPL_BUILD
  57 #define CONFIG_SPL_SKIP_RELOCATE
  58 #define CONFIG_SPL_COMMON_INIT_DDR
  59 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  60 #define CONFIG_SYS_NO_FLASH
  61 #endif
  62
  63 #ifdef CONFIG_NAND
  64 #define CONFIG_SPL_NAND_SUPPORT
  65 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  66 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  67 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  68 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  69 #define CONFIG_SYS_LDSCRIPT  "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  70 #define CONFIG_SPL_NAND_BOOT
  71 #endif
  72
  73 #ifdef CONFIG_SPIFLASH
  74 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  75 #define CONFIG_SPL_SPI_SUPPORT
  76 #define CONFIG_SPL_SPI_FLASH_SUPPORT
  77 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  78 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  79 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  80 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  81 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  82 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  83 #ifndef CONFIG_SPL_BUILD
  84 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  85 #endif
  86 #define CONFIG_SPL_SPI_BOOT
  87 #endif
  88
  89 #ifdef CONFIG_SDCARD
  90 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  91 #define CONFIG_SPL_MMC_SUPPORT
  92 #define CONFIG_SPL_MMC_MINIMAL
  93 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  94 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  95 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  96 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  97 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  98 #ifndef CONFIG_SPL_BUILD
  99 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
 100 #endif
 101 #define CONFIG_SPL_MMC_BOOT
 102 #endif
 103
 104 #endif /* CONFIG_RAMBOOT_PBL */
 105
 106 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 107 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 108 /* Set 1M boot space */
 109 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
 110 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
 111                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 112 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 113 #define CONFIG_SYS_NO_FLASH
 114 #endif
 115
 116 #ifndef CONFIG_SYS_TEXT_BASE
 117 #define CONFIG_SYS_TEXT_BASE    0xeff40000
 118 #endif
 119
 120 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 121 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 122 #endif
 123
 124 /*
 125  * These can be toggled for performance analysis, otherwise use default.
 126  */
 127 #define CONFIG_SYS_CACHE_STASHING
 128 #define CONFIG_BTB              /* toggle branch predition */
 129 #define CONFIG_DDR_ECC
 130 #ifdef CONFIG_DDR_ECC
 131 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 132 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 133 #endif
 134
 135 #define CONFIG_SYS_MEMTEST_START        0x00200000 /* memtest works on */
 136 #define CONFIG_SYS_MEMTEST_END          0x00400000
 137 #define CONFIG_SYS_ALT_MEMTEST
 138
 139 #ifndef CONFIG_SYS_NO_FLASH
 140 #define CONFIG_FLASH_CFI_DRIVER
 141 #define CONFIG_SYS_FLASH_CFI
 142 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 143 #endif
 144
 145 #if defined(CONFIG_SPIFLASH)
 146 #define CONFIG_SYS_EXTRA_ENV_RELOC
 147 #define CONFIG_ENV_IS_IN_SPI_FLASH
 148 #define CONFIG_ENV_SPI_BUS      0
 149 #define CONFIG_ENV_SPI_CS       0
 150 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 151 #define CONFIG_ENV_SPI_MODE     0
 152 #define CONFIG_ENV_SIZE         0x2000     /* 8KB */
 153 #define CONFIG_ENV_OFFSET       0x100000   /* 1MB */
 154 #define CONFIG_ENV_SECT_SIZE    0x10000
 155 #elif defined(CONFIG_SDCARD)
 156 #define CONFIG_SYS_EXTRA_ENV_RELOC
 157 #define CONFIG_ENV_IS_IN_MMC
 158 #define CONFIG_SYS_MMC_ENV_DEV  0
 159 #define CONFIG_ENV_SIZE         0x2000
 160 #define CONFIG_ENV_OFFSET       (512 * 0x800)
 161 #elif defined(CONFIG_NAND)
 162 #define CONFIG_SYS_EXTRA_ENV_RELOC
 163 #define CONFIG_ENV_IS_IN_NAND
 164 #define CONFIG_ENV_SIZE         0x2000
 165 #define CONFIG_ENV_OFFSET       (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 166 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 167 #define CONFIG_ENV_IS_IN_REMOTE
 168 #define CONFIG_ENV_ADDR         0xffe20000
 169 #define CONFIG_ENV_SIZE         0x2000
 170 #elif defined(CONFIG_ENV_IS_NOWHERE)
 171 #define CONFIG_ENV_SIZE         0x2000
 172 #else
 173 #define CONFIG_ENV_IS_IN_FLASH
 174 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 175 #define CONFIG_ENV_SIZE         0x2000
 176 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 177 #endif
 178
 179 #ifndef __ASSEMBLY__
 180 unsigned long get_board_sys_clk(void);
 181 unsigned long get_board_ddr_clk(void);
 182 #endif
 183
 184 #define CONFIG_SYS_CLK_FREQ     66660000
 185 #define CONFIG_DDR_CLK_FREQ     133330000
 186
 187 /*
 188  * Config the L3 Cache as L3 SRAM
 189  */
 190 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 191 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 192 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 193 #ifdef CONFIG_RAMBOOT_PBL
 194 #define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
 195 #endif
 196 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 197 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 198 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 199 #define CONFIG_SPL_RELOC_STACK_SIZE     (22 << 10)
 200
 201 #define CONFIG_SYS_DCSRBAR      0xf0000000
 202 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 203
 204 /* EEPROM */
 205 #define CONFIG_ID_EEPROM
 206 #define CONFIG_SYS_I2C_EEPROM_NXID
 207 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 208 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 209 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 210
 211 /*
 212  * DDR Setup
 213  */
 214 #define CONFIG_VERY_BIG_RAM
 215 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 216 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 217 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 218 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 219 #define CONFIG_DDR_SPD
 220 #define CONFIG_SYS_FSL_DDR3
 221 #undef CONFIG_FSL_DDR_INTERACTIVE
 222 #define CONFIG_SYS_SPD_BUS_NUM  0
 223 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 224 #define SPD_EEPROM_ADDRESS1     0x51
 225 #define SPD_EEPROM_ADDRESS2     0x52
 226 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 227 #define CTRL_INTLV_PREFERED     cacheline
 228
 229 /*
 230  * IFC Definitions
 231  */
 232 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 233 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 234 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 235 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 236                                 CSPR_PORT_SIZE_16 | \
 237                                 CSPR_MSEL_NOR | \
 238                                 CSPR_V)
 239 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 240
 241 /* NOR Flash Timing Params */
 242 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 243
 244 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 245                                 FTIM0_NOR_TEADC(0x5) | \
 246                                 FTIM0_NOR_TEAHC(0x5))
 247 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 248                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 249                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 250 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 251                                 FTIM2_NOR_TCH(0x4) | \
 252                                 FTIM2_NOR_TWPH(0x0E) | \
 253                                 FTIM2_NOR_TWP(0x1c))
 254 #define CONFIG_SYS_NOR_FTIM3    0x0
 255
 256 #define CONFIG_SYS_FLASH_QUIET_TEST
 257 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 258
 259 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 260 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 261 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 262 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 263 #define CONFIG_SYS_FLASH_EMPTY_INFO
 264 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 265
 266 /* CPLD on IFC */
 267 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 268 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 269 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 270 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 271                                 | CSPR_PORT_SIZE_8 \
 272                                 | CSPR_MSEL_GPCM \
 273                                 | CSPR_V)
 274 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 275 #define CONFIG_SYS_CSOR2        0x0
 276
 277 /* CPLD Timing parameters for IFC CS2 */
 278 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 279                                         FTIM0_GPCM_TEADC(0x0e) | \
 280                                         FTIM0_GPCM_TEAHC(0x0e))
 281 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 282                                         FTIM1_GPCM_TRAD(0x1f))
 283 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 284                                         FTIM2_GPCM_TCH(0x8) | \
 285                                         FTIM2_GPCM_TWP(0x1f))
 286 #define CONFIG_SYS_CS2_FTIM3            0x0
 287
 288 /* NAND Flash on IFC */
 289 #define CONFIG_NAND_FSL_IFC
 290 #define CONFIG_SYS_NAND_BASE            0xff800000
 291 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 292
 293 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 294 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 295                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 296                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 297                                 | CSPR_V)
 298 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 299
 300 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 301                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 302                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 303                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 304                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 305                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 306                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 307
 308 #define CONFIG_SYS_NAND_ONFI_DETECTION
 309
 310 /* ONFI NAND Flash mode0 Timing Params */
 311 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 312                                         FTIM0_NAND_TWP(0x18)    | \
 313                                         FTIM0_NAND_TWCHT(0x07)  | \
 314                                         FTIM0_NAND_TWH(0x0a))
 315 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 316                                         FTIM1_NAND_TWBE(0x39)   | \
 317                                         FTIM1_NAND_TRR(0x0e)    | \
 318                                         FTIM1_NAND_TRP(0x18))
 319 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 320                                         FTIM2_NAND_TREH(0x0a)   | \
 321                                         FTIM2_NAND_TWHRE(0x1e))
 322 #define CONFIG_SYS_NAND_FTIM3           0x0
 323
 324 #define CONFIG_SYS_NAND_DDR_LAW         11
 325 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 326 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 327 #define CONFIG_CMD_NAND
 328 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 329
 330 #if defined(CONFIG_NAND)
 331 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 332 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 333 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 334 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 335 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 336 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 337 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 338 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 339 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 340 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 341 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 342 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 343 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 344 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 345 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 346 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 347 #else
 348 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 349 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 350 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 351 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 352 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 353 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 354 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 355 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 356 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 357 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 358 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 359 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 360 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 361 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 362 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 363 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 364 #endif
 365
 366 #if defined(CONFIG_RAMBOOT_PBL)
 367 #define CONFIG_SYS_RAMBOOT
 368 #endif
 369
 370 #ifdef CONFIG_SPL_BUILD
 371 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 372 #else
 373 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 374 #endif
 375
 376 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 377 #define CONFIG_MISC_INIT_R
 378 #define CONFIG_HWCONFIG
 379
 380 /* define to use L1 as initial stack */
 381 #define CONFIG_L1_INIT_RAM
 382 #define CONFIG_SYS_INIT_RAM_LOCK
 383 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 384 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 385 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 386 /* The assembler doesn't like typecast */
 387 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 388                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 389                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 390 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 391 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 392                                                 GENERATED_GBL_DATA_SIZE)
 393 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 394 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 395 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 396
 397 /*
 398  * Serial Port
 399  */
 400 #define CONFIG_CONS_INDEX               1
 401 #define CONFIG_SYS_NS16550_SERIAL
 402 #define CONFIG_SYS_NS16550_REG_SIZE     1
 403 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 404 #define CONFIG_SYS_BAUDRATE_TABLE       \
 405         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 406 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 407 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 408 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 409 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 410
 411 /*
 412  * I2C
 413  */
 414 #define CONFIG_SYS_I2C
 415 #define CONFIG_SYS_I2C_FSL
 416 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 417 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 418 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 419 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 420 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 421 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 422 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 423 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 424 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 425 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 426 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 427 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 428 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 429 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 430 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 431 #define I2C_MUX_CH_DEFAULT      0x8
 432
 433 #define I2C_MUX_CH_VOL_MONITOR  0xa
 434
 435 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 436 #ifndef CONFIG_SPL_BUILD
 437 #define CONFIG_VID
 438 #endif
 439 #define CONFIG_VOL_MONITOR_IR36021_SET
 440 #define CONFIG_VOL_MONITOR_IR36021_READ
 441 /* The lowest and highest voltage allowed for T208xRDB */
 442 #define VDD_MV_MIN                      819
 443 #define VDD_MV_MAX                      1212
 444
 445 /*
 446  * RapidIO
 447  */
 448 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 449 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 450 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 451 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 452 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 453 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 454 /*
 455  * for slave u-boot IMAGE instored in master memory space,
 456  * PHYS must be aligned based on the SIZE
 457  */
 458 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 459 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 460 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 461 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 462 /*
 463  * for slave UCODE and ENV instored in master memory space,
 464  * PHYS must be aligned based on the SIZE
 465  */
 466 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 467 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 468 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 469
 470 /* slave core release by master*/
 471 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 472 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 473
 474 /*
 475  * SRIO_PCIE_BOOT - SLAVE
 476  */
 477 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 478 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 479 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 480                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 481 #endif
 482
 483 /*
 484  * eSPI - Enhanced SPI
 485  */
 486 #ifdef CONFIG_SPI_FLASH
 487 #define CONFIG_SPI_FLASH_BAR
 488 #define CONFIG_SF_DEFAULT_SPEED  10000000
 489 #define CONFIG_SF_DEFAULT_MODE    0
 490 #endif
 491
 492 /*
 493  * General PCI
 494  * Memory space is mapped 1-1, but I/O space must start from 0.
 495  */
 496 #define CONFIG_PCI              /* Enable PCI/PCIE */
 497 #define CONFIG_PCIE1            /* PCIE controller 1 */
 498 #define CONFIG_PCIE2            /* PCIE controller 2 */
 499 #define CONFIG_PCIE3            /* PCIE controller 3 */
 500 #define CONFIG_PCIE4            /* PCIE controller 4 */
 501 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 502 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 503 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 504 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 505 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 506 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 507 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 508 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 509 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 510 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 511 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 512
 513 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 514 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 515 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 516 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 517 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 518 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 519 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 520 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 521 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 522
 523 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 524 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 525 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 526 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 527 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 528 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 529 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 530 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 531 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 532
 533 /* controller 4, Base address 203000 */
 534 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 535 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 536 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 537 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 538 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 539 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 540 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 541
 542 #ifdef CONFIG_PCI
 543 #define CONFIG_PCI_INDIRECT_BRIDGE
 544 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
 545 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 546 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 547 #define CONFIG_DOS_PARTITION
 548 #endif
 549
 550 /* Qman/Bman */
 551 #ifndef CONFIG_NOBQFMAN
 552 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 553 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 554 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 555 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 556 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 557 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 558 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 559 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 560 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 561 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 562                                         CONFIG_SYS_BMAN_CENA_SIZE)
 563 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 564 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 565 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 566 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 567 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 568 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 569 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 570 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 571 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 572 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 573 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 574                                         CONFIG_SYS_QMAN_CENA_SIZE)
 575 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 576 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 577
 578 #define CONFIG_SYS_DPAA_FMAN
 579 #define CONFIG_SYS_DPAA_PME
 580 #define CONFIG_SYS_PMAN
 581 #define CONFIG_SYS_DPAA_DCE
 582 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 583 #define CONFIG_SYS_INTERLAKEN
 584
 585 /* Default address of microcode for the Linux Fman driver */
 586 #if defined(CONFIG_SPIFLASH)
 587 /*
 588  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 589  * env, so we got 0x110000.
 590  */
 591 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 592 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
 593 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 594 #define CONFIG_CORTINA_FW_ADDR          0x120000
 595
 596 #elif defined(CONFIG_SDCARD)
 597 /*
 598  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 599  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 600  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 601  */
 602 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 603 #define CONFIG_SYS_CORTINA_FW_IN_MMC
 604 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 605 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 606
 607 #elif defined(CONFIG_NAND)
 608 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 609 #define CONFIG_SYS_CORTINA_FW_IN_NAND
 610 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 611 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 612 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 613 /*
 614  * Slave has no ucode locally, it can fetch this from remote. When implementing
 615  * in two corenet boards, slave's ucode could be stored in master's memory
 616  * space, the address can be mapped from slave TLB->slave LAW->
 617  * slave SRIO or PCIE outbound window->master inbound window->
 618  * master LAW->the ucode address in master's memory space.
 619  */
 620 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 621 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE
 622 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 623 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 624 #else
 625 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 626 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 627 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 628 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 629 #endif
 630 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 631 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 632 #endif /* CONFIG_NOBQFMAN */
 633
 634 #ifdef CONFIG_SYS_DPAA_FMAN
 635 #define CONFIG_FMAN_ENET
 636 #define CONFIG_PHYLIB_10G
 637 #define CONFIG_PHY_AQUANTIA
 638 #define CONFIG_PHY_CORTINA
 639 #define CONFIG_PHY_REALTEK
 640 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 641 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 642 #define RGMII_PHY2_ADDR         0x02
 643 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 644 #define CORTINA_PHY_ADDR2       0x0d
 645 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 646 #define FM1_10GEC4_PHY_ADDR     0x01
 647 #endif
 648
 649 #ifdef CONFIG_FMAN_ENET
 650 #define CONFIG_MII              /* MII PHY management */
 651 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 652 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 653 #endif
 654
 655 /*
 656  * SATA
 657  */
 658 #ifdef CONFIG_FSL_SATA_V2
 659 #define CONFIG_LIBATA
 660 #define CONFIG_FSL_SATA
 661 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 662 #define CONFIG_SATA1
 663 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 664 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 665 #define CONFIG_SATA2
 666 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 667 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 668 #define CONFIG_LBA48
 669 #define CONFIG_CMD_SATA
 670 #define CONFIG_DOS_PARTITION
 671 #endif
 672
 673 /*
 674  * USB
 675  */
 676 #ifdef CONFIG_USB_EHCI
 677 #define CONFIG_USB_EHCI_FSL
 678 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 679 #define CONFIG_HAS_FSL_DR_USB
 680 #endif
 681
 682 /*
 683  * SDHC
 684  */
 685 #ifdef CONFIG_MMC
 686 #define CONFIG_FSL_ESDHC
 687 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 688 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 689 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 690 #define CONFIG_GENERIC_MMC
 691 #define CONFIG_DOS_PARTITION
 692 #endif
 693
 694 /*
 695  * Dynamic MTD Partition support with mtdparts
 696  */
 697 #ifndef CONFIG_SYS_NO_FLASH
 698 #define CONFIG_MTD_DEVICE
 699 #define CONFIG_MTD_PARTITIONS
 700 #define CONFIG_CMD_MTDPARTS
 701 #define CONFIG_FLASH_CFI_MTD
 702 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
 703                         "spi0=spife110000.1"
 704 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
 705                         "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
 706                         "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \
 707                         "1m(uboot),5m(kernel),128k(dtb),-(user)"
 708 #endif
 709
 710 /*
 711  * Environment
 712  */
 713
 714 /*
 715  * Command line configuration.
 716  */
 717 #define CONFIG_CMD_ERRATA
 718 #define CONFIG_CMD_REGINFO
 719
 720 #ifdef CONFIG_PCI
 721 #define CONFIG_CMD_PCI
 722 #endif
 723
 724 /* Hash command with SHA acceleration supported in hardware */
 725 #ifdef CONFIG_FSL_CAAM
 726 #define CONFIG_CMD_HASH
 727 #define CONFIG_SHA_HW_ACCEL
 728 #endif
 729
 730 /*
 731  * Miscellaneous configurable options
 732  */
 733 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 734 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 735 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 736 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 737 #ifdef CONFIG_CMD_KGDB
 738 #define CONFIG_SYS_CBSIZE       1024      /* Console I/O Buffer Size */
 739 #else
 740 #define CONFIG_SYS_CBSIZE       256       /* Console I/O Buffer Size */
 741 #endif
 742 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 743 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 744 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 745
 746 /*
 747  * For booting Linux, the board info and command line data
 748  * have to be in the first 64 MB of memory, since this is
 749  * the maximum mapped by the Linux kernel during initialization.
 750  */
 751 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 752 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 753
 754 #ifdef CONFIG_CMD_KGDB
 755 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 756 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 757 #endif
 758
 759 /*
 760  * Environment Configuration
 761  */
 762 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 763 #define CONFIG_BOOTFILE  "uImage"
 764 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 765
 766 /* default location for tftp and bootm */
 767 #define CONFIG_LOADADDR         1000000
 768 #define CONFIG_BAUDRATE         115200
 769 #define __USB_PHY_TYPE          utmi
 770
 771 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 772         "hwconfig=fsl_ddr:"                                     \
 773         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 774         "bank_intlv=auto;"                                      \
 775         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 776         "netdev=eth0\0"                                         \
 777         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 778         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 779         "tftpflash=tftpboot $loadaddr $uboot && "               \
 780         "protect off $ubootaddr +$filesize && "                 \
 781         "erase $ubootaddr +$filesize && "                       \
 782         "cp.b $loadaddr $ubootaddr $filesize && "               \
 783         "protect on $ubootaddr +$filesize && "                  \
 784         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 785         "consoledev=ttyS0\0"                                    \
 786         "ramdiskaddr=2000000\0"                                 \
 787         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 788         "fdtaddr=1e00000\0"                                     \
 789         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 790         "bdev=sda3\0"
 791
 792 /*
 793  * For emulation this causes u-boot to jump to the start of the
 794  * proof point app code automatically
 795  */
 796 #define CONFIG_PROOF_POINTS                             \
 797         "setenv bootargs root=/dev/$bdev rw "           \
 798         "console=$consoledev,$baudrate $othbootargs;"   \
 799         "cpu 1 release 0x29000000 - - -;"               \
 800         "cpu 2 release 0x29000000 - - -;"               \
 801         "cpu 3 release 0x29000000 - - -;"               \
 802         "cpu 4 release 0x29000000 - - -;"               \
 803         "cpu 5 release 0x29000000 - - -;"               \
 804         "cpu 6 release 0x29000000 - - -;"               \
 805         "cpu 7 release 0x29000000 - - -;"               \
 806         "go 0x29000000"
 807
 808 #define CONFIG_HVBOOT                           \
 809         "setenv bootargs config-addr=0x60000000; "      \
 810         "bootm 0x01000000 - 0x00f00000"
 811
 812 #define CONFIG_ALU                              \
 813         "setenv bootargs root=/dev/$bdev rw "           \
 814         "console=$consoledev,$baudrate $othbootargs;"   \
 815         "cpu 1 release 0x01000000 - - -;"               \
 816         "cpu 2 release 0x01000000 - - -;"               \
 817         "cpu 3 release 0x01000000 - - -;"               \
 818         "cpu 4 release 0x01000000 - - -;"               \
 819         "cpu 5 release 0x01000000 - - -;"               \
 820         "cpu 6 release 0x01000000 - - -;"               \
 821         "cpu 7 release 0x01000000 - - -;"               \
 822         "go 0x01000000"
 823
 824 #define CONFIG_LINUX                            \
 825         "setenv bootargs root=/dev/ram rw "             \
 826         "console=$consoledev,$baudrate $othbootargs;"   \
 827         "setenv ramdiskaddr 0x02000000;"                \
 828         "setenv fdtaddr 0x00c00000;"                    \
 829         "setenv loadaddr 0x1000000;"                    \
 830         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 831
 832 #define CONFIG_HDBOOT                                   \
 833         "setenv bootargs root=/dev/$bdev rw "           \
 834         "console=$consoledev,$baudrate $othbootargs;"   \
 835         "tftp $loadaddr $bootfile;"                     \
 836         "tftp $fdtaddr $fdtfile;"                       \
 837         "bootm $loadaddr - $fdtaddr"
 838
 839 #define CONFIG_NFSBOOTCOMMAND                   \
 840         "setenv bootargs root=/dev/nfs rw "     \
 841         "nfsroot=$serverip:$rootpath "          \
 842         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 843         "console=$consoledev,$baudrate $othbootargs;"   \
 844         "tftp $loadaddr $bootfile;"             \
 845         "tftp $fdtaddr $fdtfile;"               \
 846         "bootm $loadaddr - $fdtaddr"
 847
 848 #define CONFIG_RAMBOOTCOMMAND                           \
 849         "setenv bootargs root=/dev/ram rw "             \
 850         "console=$consoledev,$baudrate $othbootargs;"   \
 851         "tftp $ramdiskaddr $ramdiskfile;"               \
 852         "tftp $loadaddr $bootfile;"                     \
 853         "tftp $fdtaddr $fdtfile;"                       \
 854         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 855
 856 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 857
 858 #include <asm/fsl_secure_boot.h>
 859
 860 #endif  /* __T2080RDB_H */