include/configs/T208xRDB.h

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  15 #define CONFIG_FSL_SATA_V2
  16
  17 /* High Level Configuration Options */
  18 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  19 #define CONFIG_MP               /* support multiple processors */
  20 #define CONFIG_ENABLE_36BIT_PHYS
  21
  22 #ifdef CONFIG_PHYS_64BIT
  23 #define CONFIG_ADDR_MAP 1
  24 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  25 #endif
  26
  27 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  28 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  29 #define CONFIG_ENV_OVERWRITE
  30
  31 #ifdef CONFIG_RAMBOOT_PBL
  32 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  33
  34 #define CONFIG_SPL_FLUSH_IMAGE
  35 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  36 #define CONFIG_SPL_TEXT_BASE            0xFFFD8000
  37 #define CONFIG_SPL_PAD_TO               0x40000
  38 #define CONFIG_SPL_MAX_SIZE             0x28000
  39 #define RESET_VECTOR_OFFSET             0x27FFC
  40 #define BOOT_PAGE_OFFSET                0x27000
  41 #ifdef CONFIG_SPL_BUILD
  42 #define CONFIG_SPL_SKIP_RELOCATE
  43 #define CONFIG_SPL_COMMON_INIT_DDR
  44 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  45 #endif
  46
  47 #ifdef CONFIG_NAND
  48 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  49 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  50 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  51 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  52 #define CONFIG_SYS_LDSCRIPT  "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  53 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
  54 #define CONFIG_SPL_NAND_BOOT
  55 #endif
  56
  57 #ifdef CONFIG_SPIFLASH
  58 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  59 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  60 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  61 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  62 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  63 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  64 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  65 #ifndef CONFIG_SPL_BUILD
  66 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  67 #endif
  68 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
  69 #define CONFIG_SPL_SPI_BOOT
  70 #endif
  71
  72 #ifdef CONFIG_SDCARD
  73 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  74 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
  75 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
  76 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
  77 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
  78 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  79 #ifndef CONFIG_SPL_BUILD
  80 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  81 #endif
  82 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
  83 #define CONFIG_SPL_MMC_BOOT
  84 #endif
  85
  86 #endif /* CONFIG_RAMBOOT_PBL */
  87
  88 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  89 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  90 /* Set 1M boot space */
  91 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  92 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  93                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  94 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  95 #endif
  96
  97 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  98 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  99 #endif
 100
 101 /*
 102  * These can be toggled for performance analysis, otherwise use default.
 103  */
 104 #define CONFIG_SYS_CACHE_STASHING
 105 #define CONFIG_BTB              /* toggle branch predition */
 106 #define CONFIG_DDR_ECC
 107 #ifdef CONFIG_DDR_ECC
 108 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 109 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 110 #endif
 111
 112 #define CONFIG_SYS_MEMTEST_START        0x00200000 /* memtest works on */
 113 #define CONFIG_SYS_MEMTEST_END          0x00400000
 114 #define CONFIG_SYS_ALT_MEMTEST
 115
 116 #ifdef CONFIG_MTD_NOR_FLASH
 117 #define CONFIG_FLASH_CFI_DRIVER
 118 #define CONFIG_SYS_FLASH_CFI
 119 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 120 #endif
 121
 122 #if defined(CONFIG_SPIFLASH)
 123 #define CONFIG_SYS_EXTRA_ENV_RELOC
 124 #define CONFIG_ENV_SPI_BUS      0
 125 #define CONFIG_ENV_SPI_CS       0
 126 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 127 #define CONFIG_ENV_SPI_MODE     0
 128 #define CONFIG_ENV_SIZE         0x2000     /* 8KB */
 129 #define CONFIG_ENV_OFFSET       0x100000   /* 1MB */
 130 #define CONFIG_ENV_SECT_SIZE    0x10000
 131 #elif defined(CONFIG_SDCARD)
 132 #define CONFIG_SYS_EXTRA_ENV_RELOC
 133 #define CONFIG_SYS_MMC_ENV_DEV  0
 134 #define CONFIG_ENV_SIZE         0x2000
 135 #define CONFIG_ENV_OFFSET       (512 * 0x800)
 136 #elif defined(CONFIG_NAND)
 137 #define CONFIG_SYS_EXTRA_ENV_RELOC
 138 #define CONFIG_ENV_SIZE         0x2000
 139 #define CONFIG_ENV_OFFSET       (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 140 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 141 #define CONFIG_ENV_ADDR         0xffe20000
 142 #define CONFIG_ENV_SIZE         0x2000
 143 #elif defined(CONFIG_ENV_IS_NOWHERE)
 144 #define CONFIG_ENV_SIZE         0x2000
 145 #else
 146 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 147 #define CONFIG_ENV_SIZE         0x2000
 148 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 149 #endif
 150
 151 #ifndef __ASSEMBLY__
 152 unsigned long get_board_sys_clk(void);
 153 unsigned long get_board_ddr_clk(void);
 154 #endif
 155
 156 #define CONFIG_SYS_CLK_FREQ     66660000
 157 #define CONFIG_DDR_CLK_FREQ     133330000
 158
 159 /*
 160  * Config the L3 Cache as L3 SRAM
 161  */
 162 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 163 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 164 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 165 #ifdef CONFIG_RAMBOOT_PBL
 166 #define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
 167 #endif
 168 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 169 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 170 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 171 #define CONFIG_SPL_RELOC_STACK_SIZE     (22 << 10)
 172
 173 #define CONFIG_SYS_DCSRBAR      0xf0000000
 174 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 175
 176 /* EEPROM */
 177 #define CONFIG_ID_EEPROM
 178 #define CONFIG_SYS_I2C_EEPROM_NXID
 179 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 180 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 181 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 182
 183 /*
 184  * DDR Setup
 185  */
 186 #define CONFIG_VERY_BIG_RAM
 187 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 188 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 189 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 190 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 191 #define CONFIG_DDR_SPD
 192 #undef CONFIG_FSL_DDR_INTERACTIVE
 193 #define CONFIG_SYS_SPD_BUS_NUM  0
 194 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 195 #define SPD_EEPROM_ADDRESS1     0x51
 196 #define SPD_EEPROM_ADDRESS2     0x52
 197 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 198 #define CTRL_INTLV_PREFERED     cacheline
 199
 200 /*
 201  * IFC Definitions
 202  */
 203 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 204 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 205 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 206 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 207                                 CSPR_PORT_SIZE_16 | \
 208                                 CSPR_MSEL_NOR | \
 209                                 CSPR_V)
 210 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 211
 212 /* NOR Flash Timing Params */
 213 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 214
 215 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 216                                 FTIM0_NOR_TEADC(0x5) | \
 217                                 FTIM0_NOR_TEAHC(0x5))
 218 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 219                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 220                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 221 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 222                                 FTIM2_NOR_TCH(0x4) | \
 223                                 FTIM2_NOR_TWPH(0x0E) | \
 224                                 FTIM2_NOR_TWP(0x1c))
 225 #define CONFIG_SYS_NOR_FTIM3    0x0
 226
 227 #define CONFIG_SYS_FLASH_QUIET_TEST
 228 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 229
 230 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 231 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 232 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 233 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 234 #define CONFIG_SYS_FLASH_EMPTY_INFO
 235 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 236
 237 /* CPLD on IFC */
 238 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 239 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 240 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 241 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 242                                 | CSPR_PORT_SIZE_8 \
 243                                 | CSPR_MSEL_GPCM \
 244                                 | CSPR_V)
 245 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 246 #define CONFIG_SYS_CSOR2        0x0
 247
 248 /* CPLD Timing parameters for IFC CS2 */
 249 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 250                                         FTIM0_GPCM_TEADC(0x0e) | \
 251                                         FTIM0_GPCM_TEAHC(0x0e))
 252 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 253                                         FTIM1_GPCM_TRAD(0x1f))
 254 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 255                                         FTIM2_GPCM_TCH(0x8) | \
 256                                         FTIM2_GPCM_TWP(0x1f))
 257 #define CONFIG_SYS_CS2_FTIM3            0x0
 258
 259 /* NAND Flash on IFC */
 260 #define CONFIG_NAND_FSL_IFC
 261 #define CONFIG_SYS_NAND_BASE            0xff800000
 262 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 263
 264 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 265 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 266                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 267                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 268                                 | CSPR_V)
 269 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 270
 271 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 272                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 273                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 274                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 275                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 276                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 277                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 278
 279 #define CONFIG_SYS_NAND_ONFI_DETECTION
 280
 281 /* ONFI NAND Flash mode0 Timing Params */
 282 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 283                                         FTIM0_NAND_TWP(0x18)    | \
 284                                         FTIM0_NAND_TWCHT(0x07)  | \
 285                                         FTIM0_NAND_TWH(0x0a))
 286 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 287                                         FTIM1_NAND_TWBE(0x39)   | \
 288                                         FTIM1_NAND_TRR(0x0e)    | \
 289                                         FTIM1_NAND_TRP(0x18))
 290 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 291                                         FTIM2_NAND_TREH(0x0a)   | \
 292                                         FTIM2_NAND_TWHRE(0x1e))
 293 #define CONFIG_SYS_NAND_FTIM3           0x0
 294
 295 #define CONFIG_SYS_NAND_DDR_LAW         11
 296 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 297 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 298 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 299
 300 #if defined(CONFIG_NAND)
 301 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 302 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 303 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 304 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 305 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 306 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 307 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 308 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 309 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 310 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 311 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 312 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 313 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 314 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 315 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 316 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 317 #else
 318 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 319 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 320 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 321 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 322 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 323 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 324 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 325 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 326 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 327 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 328 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 329 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 330 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 331 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 332 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 333 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 334 #endif
 335
 336 #if defined(CONFIG_RAMBOOT_PBL)
 337 #define CONFIG_SYS_RAMBOOT
 338 #endif
 339
 340 #ifdef CONFIG_SPL_BUILD
 341 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 342 #else
 343 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 344 #endif
 345
 346 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 347 #define CONFIG_MISC_INIT_R
 348 #define CONFIG_HWCONFIG
 349
 350 /* define to use L1 as initial stack */
 351 #define CONFIG_L1_INIT_RAM
 352 #define CONFIG_SYS_INIT_RAM_LOCK
 353 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 354 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 355 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 356 /* The assembler doesn't like typecast */
 357 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 358                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 359                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 360 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 361 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 362                                                 GENERATED_GBL_DATA_SIZE)
 363 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 364 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 365 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 366
 367 /*
 368  * Serial Port
 369  */
 370 #define CONFIG_CONS_INDEX               1
 371 #define CONFIG_SYS_NS16550_SERIAL
 372 #define CONFIG_SYS_NS16550_REG_SIZE     1
 373 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 374 #define CONFIG_SYS_BAUDRATE_TABLE       \
 375         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 376 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 377 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 378 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 379 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 380
 381 /*
 382  * I2C
 383  */
 384 #define CONFIG_SYS_I2C
 385 #define CONFIG_SYS_I2C_FSL
 386 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 387 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 388 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 389 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 390 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 391 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 392 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 393 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 394 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 395 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 396 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 397 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 398 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 399 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 400 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 401 #define I2C_MUX_CH_DEFAULT      0x8
 402
 403 #define I2C_MUX_CH_VOL_MONITOR  0xa
 404
 405 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 406 #ifndef CONFIG_SPL_BUILD
 407 #define CONFIG_VID
 408 #endif
 409 #define CONFIG_VOL_MONITOR_IR36021_SET
 410 #define CONFIG_VOL_MONITOR_IR36021_READ
 411 /* The lowest and highest voltage allowed for T208xRDB */
 412 #define VDD_MV_MIN                      819
 413 #define VDD_MV_MAX                      1212
 414
 415 /*
 416  * RapidIO
 417  */
 418 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 419 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 420 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 421 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 422 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 423 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 424 /*
 425  * for slave u-boot IMAGE instored in master memory space,
 426  * PHYS must be aligned based on the SIZE
 427  */
 428 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 429 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 430 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 431 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 432 /*
 433  * for slave UCODE and ENV instored in master memory space,
 434  * PHYS must be aligned based on the SIZE
 435  */
 436 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 437 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 438 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 439
 440 /* slave core release by master*/
 441 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 442 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 443
 444 /*
 445  * SRIO_PCIE_BOOT - SLAVE
 446  */
 447 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 448 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 449 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 450                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 451 #endif
 452
 453 /*
 454  * eSPI - Enhanced SPI
 455  */
 456 #ifdef CONFIG_SPI_FLASH
 457 #define CONFIG_SPI_FLASH_BAR
 458 #define CONFIG_SF_DEFAULT_SPEED  10000000
 459 #define CONFIG_SF_DEFAULT_MODE    0
 460 #endif
 461
 462 /*
 463  * General PCI
 464  * Memory space is mapped 1-1, but I/O space must start from 0.
 465  */
 466 #define CONFIG_PCIE1            /* PCIE controller 1 */
 467 #define CONFIG_PCIE2            /* PCIE controller 2 */
 468 #define CONFIG_PCIE3            /* PCIE controller 3 */
 469 #define CONFIG_PCIE4            /* PCIE controller 4 */
 470 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 471 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 472 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 473 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 474 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 475 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 476 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 477 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 478 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 479 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 480 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 481
 482 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 483 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 484 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 485 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 486 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 487 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 488 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 489 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 490 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 491
 492 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 493 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 494 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 495 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 496 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 497 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 498 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 499 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 500 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 501
 502 /* controller 4, Base address 203000 */
 503 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 504 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 505 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 506 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 507 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 508 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 509 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 510
 511 #ifdef CONFIG_PCI
 512 #define CONFIG_PCI_INDIRECT_BRIDGE
 513 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
 514 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 515 #endif
 516
 517 /* Qman/Bman */
 518 #ifndef CONFIG_NOBQFMAN
 519 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 520 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 521 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 522 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 523 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 524 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 525 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 526 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 527 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 528                                         CONFIG_SYS_BMAN_CENA_SIZE)
 529 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 530 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 531 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 532 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 533 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 534 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 535 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 536 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 537 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 538 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 539 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 540                                         CONFIG_SYS_QMAN_CENA_SIZE)
 541 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 542 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 543
 544 #define CONFIG_SYS_DPAA_FMAN
 545 #define CONFIG_SYS_DPAA_PME
 546 #define CONFIG_SYS_PMAN
 547 #define CONFIG_SYS_DPAA_DCE
 548 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 549 #define CONFIG_SYS_INTERLAKEN
 550
 551 /* Default address of microcode for the Linux Fman driver */
 552 #if defined(CONFIG_SPIFLASH)
 553 /*
 554  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 555  * env, so we got 0x110000.
 556  */
 557 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 558 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
 559 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 560 #define CONFIG_CORTINA_FW_ADDR          0x120000
 561
 562 #elif defined(CONFIG_SDCARD)
 563 /*
 564  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 565  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 566  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 567  */
 568 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 569 #define CONFIG_SYS_CORTINA_FW_IN_MMC
 570 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 571 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 572
 573 #elif defined(CONFIG_NAND)
 574 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 575 #define CONFIG_SYS_CORTINA_FW_IN_NAND
 576 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 577 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 578 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 579 /*
 580  * Slave has no ucode locally, it can fetch this from remote. When implementing
 581  * in two corenet boards, slave's ucode could be stored in master's memory
 582  * space, the address can be mapped from slave TLB->slave LAW->
 583  * slave SRIO or PCIE outbound window->master inbound window->
 584  * master LAW->the ucode address in master's memory space.
 585  */
 586 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 587 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE
 588 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 589 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 590 #else
 591 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 592 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 593 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 594 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 595 #endif
 596 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 597 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 598 #endif /* CONFIG_NOBQFMAN */
 599
 600 #ifdef CONFIG_SYS_DPAA_FMAN
 601 #define CONFIG_FMAN_ENET
 602 #define CONFIG_PHYLIB_10G
 603 #define CONFIG_PHY_AQUANTIA
 604 #define CONFIG_PHY_CORTINA
 605 #define CONFIG_PHY_REALTEK
 606 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 607 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 608 #define RGMII_PHY2_ADDR         0x02
 609 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 610 #define CORTINA_PHY_ADDR2       0x0d
 611 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 612 #define FM1_10GEC4_PHY_ADDR     0x01
 613 #endif
 614
 615 #ifdef CONFIG_FMAN_ENET
 616 #define CONFIG_MII              /* MII PHY management */
 617 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 618 #endif
 619
 620 /*
 621  * SATA
 622  */
 623 #ifdef CONFIG_FSL_SATA_V2
 624 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 625 #define CONFIG_SATA1
 626 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 627 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 628 #define CONFIG_SATA2
 629 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 630 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 631 #define CONFIG_LBA48
 632 #endif
 633
 634 /*
 635  * USB
 636  */
 637 #ifdef CONFIG_USB_EHCI_HCD
 638 #define CONFIG_USB_EHCI_FSL
 639 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 640 #define CONFIG_HAS_FSL_DR_USB
 641 #endif
 642
 643 /*
 644  * SDHC
 645  */
 646 #ifdef CONFIG_MMC
 647 #define CONFIG_FSL_ESDHC
 648 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 649 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 650 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 651 #endif
 652
 653 /*
 654  * Dynamic MTD Partition support with mtdparts
 655  */
 656 #ifdef CONFIG_MTD_NOR_FLASH
 657 #define CONFIG_MTD_DEVICE
 658 #define CONFIG_MTD_PARTITIONS
 659 #define CONFIG_FLASH_CFI_MTD
 660 #endif
 661
 662 /*
 663  * Environment
 664  */
 665
 666 /*
 667  * Miscellaneous configurable options
 668  */
 669 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 670 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 671 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 672 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 673
 674 /*
 675  * For booting Linux, the board info and command line data
 676  * have to be in the first 64 MB of memory, since this is
 677  * the maximum mapped by the Linux kernel during initialization.
 678  */
 679 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 680 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 681
 682 #ifdef CONFIG_CMD_KGDB
 683 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 684 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 685 #endif
 686
 687 /*
 688  * Environment Configuration
 689  */
 690 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 691 #define CONFIG_BOOTFILE  "uImage"
 692 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 693
 694 /* default location for tftp and bootm */
 695 #define CONFIG_LOADADDR         1000000
 696 #define __USB_PHY_TYPE          utmi
 697
 698 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 699         "hwconfig=fsl_ddr:"                                     \
 700         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 701         "bank_intlv=auto;"                                      \
 702         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 703         "netdev=eth0\0"                                         \
 704         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 705         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 706         "tftpflash=tftpboot $loadaddr $uboot && "               \
 707         "protect off $ubootaddr +$filesize && "                 \
 708         "erase $ubootaddr +$filesize && "                       \
 709         "cp.b $loadaddr $ubootaddr $filesize && "               \
 710         "protect on $ubootaddr +$filesize && "                  \
 711         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 712         "consoledev=ttyS0\0"                                    \
 713         "ramdiskaddr=2000000\0"                                 \
 714         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 715         "fdtaddr=1e00000\0"                                     \
 716         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 717         "bdev=sda3\0"
 718
 719 /*
 720  * For emulation this causes u-boot to jump to the start of the
 721  * proof point app code automatically
 722  */
 723 #define CONFIG_PROOF_POINTS                             \
 724         "setenv bootargs root=/dev/$bdev rw "           \
 725         "console=$consoledev,$baudrate $othbootargs;"   \
 726         "cpu 1 release 0x29000000 - - -;"               \
 727         "cpu 2 release 0x29000000 - - -;"               \
 728         "cpu 3 release 0x29000000 - - -;"               \
 729         "cpu 4 release 0x29000000 - - -;"               \
 730         "cpu 5 release 0x29000000 - - -;"               \
 731         "cpu 6 release 0x29000000 - - -;"               \
 732         "cpu 7 release 0x29000000 - - -;"               \
 733         "go 0x29000000"
 734
 735 #define CONFIG_HVBOOT                           \
 736         "setenv bootargs config-addr=0x60000000; "      \
 737         "bootm 0x01000000 - 0x00f00000"
 738
 739 #define CONFIG_ALU                              \
 740         "setenv bootargs root=/dev/$bdev rw "           \
 741         "console=$consoledev,$baudrate $othbootargs;"   \
 742         "cpu 1 release 0x01000000 - - -;"               \
 743         "cpu 2 release 0x01000000 - - -;"               \
 744         "cpu 3 release 0x01000000 - - -;"               \
 745         "cpu 4 release 0x01000000 - - -;"               \
 746         "cpu 5 release 0x01000000 - - -;"               \
 747         "cpu 6 release 0x01000000 - - -;"               \
 748         "cpu 7 release 0x01000000 - - -;"               \
 749         "go 0x01000000"
 750
 751 #define CONFIG_LINUX                            \
 752         "setenv bootargs root=/dev/ram rw "             \
 753         "console=$consoledev,$baudrate $othbootargs;"   \
 754         "setenv ramdiskaddr 0x02000000;"                \
 755         "setenv fdtaddr 0x00c00000;"                    \
 756         "setenv loadaddr 0x1000000;"                    \
 757         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 758
 759 #define CONFIG_HDBOOT                                   \
 760         "setenv bootargs root=/dev/$bdev rw "           \
 761         "console=$consoledev,$baudrate $othbootargs;"   \
 762         "tftp $loadaddr $bootfile;"                     \
 763         "tftp $fdtaddr $fdtfile;"                       \
 764         "bootm $loadaddr - $fdtaddr"
 765
 766 #define CONFIG_NFSBOOTCOMMAND                   \
 767         "setenv bootargs root=/dev/nfs rw "     \
 768         "nfsroot=$serverip:$rootpath "          \
 769         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 770         "console=$consoledev,$baudrate $othbootargs;"   \
 771         "tftp $loadaddr $bootfile;"             \
 772         "tftp $fdtaddr $fdtfile;"               \
 773         "bootm $loadaddr - $fdtaddr"
 774
 775 #define CONFIG_RAMBOOTCOMMAND                           \
 776         "setenv bootargs root=/dev/ram rw "             \
 777         "console=$consoledev,$baudrate $othbootargs;"   \
 778         "tftp $ramdiskaddr $ramdiskfile;"               \
 779         "tftp $loadaddr $bootfile;"                     \
 780         "tftp $fdtaddr $fdtfile;"                       \
 781         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 782
 783 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 784
 785 #include <asm/fsl_secure_boot.h>
 786
 787 #endif  /* __T2080RDB_H */