include/configs/T208xRDB.h

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * T2080 RDB/PCIe board configuration file
   9  */
  10
  11 #ifndef __T2080RDB_H
  12 #define __T2080RDB_H
  13
  14 #define CONFIG_DISPLAY_BOARDINFO
  15 #define CONFIG_T2080RDB
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #define CONFIG_MMC
  18 #define CONFIG_USB_EHCI
  19 #define CONFIG_FSL_SATA_V2
  20
  21 /* High Level Configuration Options */
  22 #define CONFIG_PHYS_64BIT
  23 #define CONFIG_BOOKE
  24 #define CONFIG_E500             /* BOOKE e500 family */
  25 #define CONFIG_E500MC           /* BOOKE e500mc family */
  26 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  27 #define CONFIG_MP               /* support multiple processors */
  28 #define CONFIG_ENABLE_36BIT_PHYS
  29
  30 #ifdef CONFIG_PHYS_64BIT
  31 #define CONFIG_ADDR_MAP 1
  32 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  33 #endif
  34
  35 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  36 #define CONFIG_SYS_NUM_CPC      CONFIG_NUM_DDR_CONTROLLERS
  37 #define CONFIG_FSL_IFC          /* Enable IFC Support */
  38 #define CONFIG_FSL_CAAM         /* Enable SEC/CAAM */
  39 #define CONFIG_FSL_LAW          /* Use common FSL init code */
  40 #define CONFIG_ENV_OVERWRITE
  41
  42 #ifdef CONFIG_RAMBOOT_PBL
  43 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg
  44 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_rcw.cfg
  45
  46 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
  47 #define CONFIG_SPL_ENV_SUPPORT
  48 #define CONFIG_SPL_SERIAL_SUPPORT
  49 #define CONFIG_SPL_FLUSH_IMAGE
  50 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  51 #define CONFIG_SPL_LIBGENERIC_SUPPORT
  52 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  53 #define CONFIG_SPL_I2C_SUPPORT
  54 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  55 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  56 #define CONFIG_SYS_TEXT_BASE            0x00201000
  57 #define CONFIG_SPL_TEXT_BASE            0xFFFD8000
  58 #define CONFIG_SPL_PAD_TO               0x40000
  59 #define CONFIG_SPL_MAX_SIZE             0x28000
  60 #define RESET_VECTOR_OFFSET             0x27FFC
  61 #define BOOT_PAGE_OFFSET                0x27000
  62 #ifdef CONFIG_SPL_BUILD
  63 #define CONFIG_SPL_SKIP_RELOCATE
  64 #define CONFIG_SPL_COMMON_INIT_DDR
  65 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  66 #define CONFIG_SYS_NO_FLASH
  67 #endif
  68
  69 #ifdef CONFIG_NAND
  70 #define CONFIG_SPL_NAND_SUPPORT
  71 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  72 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  73 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  74 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  75 #define CONFIG_SYS_LDSCRIPT  "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
  76 #define CONFIG_SPL_NAND_BOOT
  77 #endif
  78
  79 #ifdef CONFIG_SPIFLASH
  80 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  81 #define CONFIG_SPL_SPI_SUPPORT
  82 #define CONFIG_SPL_SPI_FLASH_SUPPORT
  83 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  84 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
  85 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
  86 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
  87 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
  88 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
  89 #ifndef CONFIG_SPL_BUILD
  90 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  91 #endif
  92 #define CONFIG_SPL_SPI_BOOT
  93 #endif
  94
  95 #ifdef CONFIG_SDCARD
  96 #define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  97 #define CONFIG_SPL_MMC_SUPPORT
  98 #define CONFIG_SPL_MMC_MINIMAL
  99 #define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
 100 #define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
 101 #define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
 102 #define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
 103 #define CONFIG_SYS_LDSCRIPT    "arch/powerpc/cpu/mpc85xx/u-boot.lds"
 104 #ifndef CONFIG_SPL_BUILD
 105 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
 106 #endif
 107 #define CONFIG_SPL_MMC_BOOT
 108 #endif
 109
 110 #endif /* CONFIG_RAMBOOT_PBL */
 111
 112 #define CONFIG_SRIO_PCIE_BOOT_MASTER
 113 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 114 /* Set 1M boot space */
 115 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
 116 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
 117                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 118 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 119 #define CONFIG_SYS_NO_FLASH
 120 #endif
 121
 122 #ifndef CONFIG_SYS_TEXT_BASE
 123 #define CONFIG_SYS_TEXT_BASE    0xeff40000
 124 #endif
 125
 126 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 127 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 128 #endif
 129
 130 /*
 131  * These can be toggled for performance analysis, otherwise use default.
 132  */
 133 #define CONFIG_SYS_CACHE_STASHING
 134 #define CONFIG_BTB              /* toggle branch predition */
 135 #define CONFIG_DDR_ECC
 136 #ifdef CONFIG_DDR_ECC
 137 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 138 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 139 #endif
 140
 141 #define CONFIG_CMD_MEMTEST
 142 #define CONFIG_SYS_MEMTEST_START        0x00200000 /* memtest works on */
 143 #define CONFIG_SYS_MEMTEST_END          0x00400000
 144 #define CONFIG_SYS_ALT_MEMTEST
 145
 146 #ifndef CONFIG_SYS_NO_FLASH
 147 #define CONFIG_FLASH_CFI_DRIVER
 148 #define CONFIG_SYS_FLASH_CFI
 149 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 150 #endif
 151
 152 #if defined(CONFIG_SPIFLASH)
 153 #define CONFIG_SYS_EXTRA_ENV_RELOC
 154 #define CONFIG_ENV_IS_IN_SPI_FLASH
 155 #define CONFIG_ENV_SPI_BUS      0
 156 #define CONFIG_ENV_SPI_CS       0
 157 #define CONFIG_ENV_SPI_MAX_HZ   10000000
 158 #define CONFIG_ENV_SPI_MODE     0
 159 #define CONFIG_ENV_SIZE         0x2000     /* 8KB */
 160 #define CONFIG_ENV_OFFSET       0x100000   /* 1MB */
 161 #define CONFIG_ENV_SECT_SIZE    0x10000
 162 #elif defined(CONFIG_SDCARD)
 163 #define CONFIG_SYS_EXTRA_ENV_RELOC
 164 #define CONFIG_ENV_IS_IN_MMC
 165 #define CONFIG_SYS_MMC_ENV_DEV  0
 166 #define CONFIG_ENV_SIZE         0x2000
 167 #define CONFIG_ENV_OFFSET       (512 * 0x800)
 168 #elif defined(CONFIG_NAND)
 169 #define CONFIG_SYS_EXTRA_ENV_RELOC
 170 #define CONFIG_ENV_IS_IN_NAND
 171 #define CONFIG_ENV_SIZE         0x2000
 172 #define CONFIG_ENV_OFFSET       (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
 173 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 174 #define CONFIG_ENV_IS_IN_REMOTE
 175 #define CONFIG_ENV_ADDR         0xffe20000
 176 #define CONFIG_ENV_SIZE         0x2000
 177 #elif defined(CONFIG_ENV_IS_NOWHERE)
 178 #define CONFIG_ENV_SIZE         0x2000
 179 #else
 180 #define CONFIG_ENV_IS_IN_FLASH
 181 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 182 #define CONFIG_ENV_SIZE         0x2000
 183 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 184 #endif
 185
 186 #ifndef __ASSEMBLY__
 187 unsigned long get_board_sys_clk(void);
 188 unsigned long get_board_ddr_clk(void);
 189 #endif
 190
 191 #define CONFIG_SYS_CLK_FREQ     66660000
 192 #define CONFIG_DDR_CLK_FREQ     133330000
 193
 194 /*
 195  * Config the L3 Cache as L3 SRAM
 196  */
 197 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 198 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 199 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 200 #ifdef CONFIG_RAMBOOT_PBL
 201 #define CONFIG_ENV_ADDR                 (CONFIG_SPL_GD_ADDR + 4 * 1024)
 202 #endif
 203 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 204 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 205 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 206 #define CONFIG_SPL_RELOC_STACK_SIZE     (22 << 10)
 207
 208 #define CONFIG_SYS_DCSRBAR      0xf0000000
 209 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 210
 211 /* EEPROM */
 212 #define CONFIG_ID_EEPROM
 213 #define CONFIG_SYS_I2C_EEPROM_NXID
 214 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 215 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
 216 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
 217
 218 /*
 219  * DDR Setup
 220  */
 221 #define CONFIG_VERY_BIG_RAM
 222 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 223 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 224 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 225 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 226 #define CONFIG_DDR_SPD
 227 #define CONFIG_SYS_FSL_DDR3
 228 #undef CONFIG_FSL_DDR_INTERACTIVE
 229 #define CONFIG_SYS_SPD_BUS_NUM  0
 230 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 231 #define SPD_EEPROM_ADDRESS1     0x51
 232 #define SPD_EEPROM_ADDRESS2     0x52
 233 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 234 #define CTRL_INTLV_PREFERED     cacheline
 235
 236 /*
 237  * IFC Definitions
 238  */
 239 #define CONFIG_SYS_FLASH_BASE           0xe8000000
 240 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 241 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 242 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 243                                 CSPR_PORT_SIZE_16 | \
 244                                 CSPR_MSEL_NOR | \
 245                                 CSPR_V)
 246 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 247
 248 /* NOR Flash Timing Params */
 249 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 250
 251 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 252                                 FTIM0_NOR_TEADC(0x5) | \
 253                                 FTIM0_NOR_TEAHC(0x5))
 254 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 255                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 256                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 257 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 258                                 FTIM2_NOR_TCH(0x4) | \
 259                                 FTIM2_NOR_TWPH(0x0E) | \
 260                                 FTIM2_NOR_TWP(0x1c))
 261 #define CONFIG_SYS_NOR_FTIM3    0x0
 262
 263 #define CONFIG_SYS_FLASH_QUIET_TEST
 264 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 265
 266 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 267 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 268 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 269 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 270 #define CONFIG_SYS_FLASH_EMPTY_INFO
 271 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }
 272
 273 /* CPLD on IFC */
 274 #define CONFIG_SYS_CPLD_BASE    0xffdf0000
 275 #define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
 276 #define CONFIG_SYS_CSPR2_EXT    (0xf)
 277 #define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
 278                                 | CSPR_PORT_SIZE_8 \
 279                                 | CSPR_MSEL_GPCM \
 280                                 | CSPR_V)
 281 #define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
 282 #define CONFIG_SYS_CSOR2        0x0
 283
 284 /* CPLD Timing parameters for IFC CS2 */
 285 #define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 286                                         FTIM0_GPCM_TEADC(0x0e) | \
 287                                         FTIM0_GPCM_TEAHC(0x0e))
 288 #define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 289                                         FTIM1_GPCM_TRAD(0x1f))
 290 #define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 291                                         FTIM2_GPCM_TCH(0x8) | \
 292                                         FTIM2_GPCM_TWP(0x1f))
 293 #define CONFIG_SYS_CS2_FTIM3            0x0
 294
 295 /* NAND Flash on IFC */
 296 #define CONFIG_NAND_FSL_IFC
 297 #define CONFIG_SYS_NAND_BASE            0xff800000
 298 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 299
 300 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 301 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 302                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 303                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 304                                 | CSPR_V)
 305 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 306
 307 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 308                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 309                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 310                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 311                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 312                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 313                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 314
 315 #define CONFIG_SYS_NAND_ONFI_DETECTION
 316
 317 /* ONFI NAND Flash mode0 Timing Params */
 318 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 319                                         FTIM0_NAND_TWP(0x18)    | \
 320                                         FTIM0_NAND_TWCHT(0x07)  | \
 321                                         FTIM0_NAND_TWH(0x0a))
 322 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 323                                         FTIM1_NAND_TWBE(0x39)   | \
 324                                         FTIM1_NAND_TRR(0x0e)    | \
 325                                         FTIM1_NAND_TRP(0x18))
 326 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 327                                         FTIM2_NAND_TREH(0x0a)   | \
 328                                         FTIM2_NAND_TWHRE(0x1e))
 329 #define CONFIG_SYS_NAND_FTIM3           0x0
 330
 331 #define CONFIG_SYS_NAND_DDR_LAW         11
 332 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 333 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 334 #define CONFIG_CMD_NAND
 335 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 336
 337 #if defined(CONFIG_NAND)
 338 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 339 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 340 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 341 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 342 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 343 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 344 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 345 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 346 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 347 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 348 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 349 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 350 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 351 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 352 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 353 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 354 #else
 355 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 356 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 357 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 358 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 359 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 360 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 361 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 362 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 363 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
 364 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
 365 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
 366 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
 367 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
 368 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
 369 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
 370 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
 371 #endif
 372
 373 #if defined(CONFIG_RAMBOOT_PBL)
 374 #define CONFIG_SYS_RAMBOOT
 375 #endif
 376
 377 #ifdef CONFIG_SPL_BUILD
 378 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
 379 #else
 380 #define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
 381 #endif
 382
 383 #define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */
 384 #define CONFIG_MISC_INIT_R
 385 #define CONFIG_HWCONFIG
 386
 387 /* define to use L1 as initial stack */
 388 #define CONFIG_L1_INIT_RAM
 389 #define CONFIG_SYS_INIT_RAM_LOCK
 390 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 391 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 392 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 393 /* The assembler doesn't like typecast */
 394 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 395                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 396                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 397 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 398 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 399                                                 GENERATED_GBL_DATA_SIZE)
 400 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 401 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 402 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 403
 404 /*
 405  * Serial Port
 406  */
 407 #define CONFIG_CONS_INDEX               1
 408 #define CONFIG_SYS_NS16550_SERIAL
 409 #define CONFIG_SYS_NS16550_REG_SIZE     1
 410 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 411 #define CONFIG_SYS_BAUDRATE_TABLE       \
 412         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 413 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 414 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 415 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 416 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 417
 418 /* Use the HUSH parser */
 419 #define CONFIG_SYS_HUSH_PARSER
 420 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 421
 422 /*
 423  * I2C
 424  */
 425 #define CONFIG_SYS_I2C
 426 #define CONFIG_SYS_I2C_FSL
 427 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 428 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 429 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 430 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 431 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 432 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 433 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 434 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 435 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 436 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 437 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 438 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 439 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 440 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 441 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 442 #define I2C_MUX_CH_DEFAULT      0x8
 443
 444 #define I2C_MUX_CH_VOL_MONITOR  0xa
 445
 446 #define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
 447 #ifndef CONFIG_SPL_BUILD
 448 #define CONFIG_VID
 449 #endif
 450 #define CONFIG_VOL_MONITOR_IR36021_SET
 451 #define CONFIG_VOL_MONITOR_IR36021_READ
 452 /* The lowest and highest voltage allowed for T208xRDB */
 453 #define VDD_MV_MIN                      819
 454 #define VDD_MV_MAX                      1212
 455
 456 /*
 457  * RapidIO
 458  */
 459 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 460 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 461 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 462 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 463 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 464 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 465 /*
 466  * for slave u-boot IMAGE instored in master memory space,
 467  * PHYS must be aligned based on the SIZE
 468  */
 469 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 470 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 471 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 472 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 473 /*
 474  * for slave UCODE and ENV instored in master memory space,
 475  * PHYS must be aligned based on the SIZE
 476  */
 477 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 478 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 479 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 480
 481 /* slave core release by master*/
 482 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 483 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 484
 485 /*
 486  * SRIO_PCIE_BOOT - SLAVE
 487  */
 488 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 489 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 490 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 491                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 492 #endif
 493
 494 /*
 495  * eSPI - Enhanced SPI
 496  */
 497 #ifdef CONFIG_SPI_FLASH
 498 #define CONFIG_SPI_FLASH_BAR
 499 #define CONFIG_CMD_SF
 500 #define CONFIG_SF_DEFAULT_SPEED  10000000
 501 #define CONFIG_SF_DEFAULT_MODE    0
 502 #endif
 503
 504 /*
 505  * General PCI
 506  * Memory space is mapped 1-1, but I/O space must start from 0.
 507  */
 508 #define CONFIG_PCI              /* Enable PCI/PCIE */
 509 #define CONFIG_PCIE1            /* PCIE controler 1 */
 510 #define CONFIG_PCIE2            /* PCIE controler 2 */
 511 #define CONFIG_PCIE3            /* PCIE controler 3 */
 512 #define CONFIG_PCIE4            /* PCIE controler 4 */
 513 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 514 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 515 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 516 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 517 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 518 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 519 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 520 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 521 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 522 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 523 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 524
 525 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 526 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 527 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 528 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 529 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 530 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 531 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 532 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 533 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 534
 535 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 536 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 537 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 538 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 539 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 540 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 541 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 542 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 543 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 544
 545 /* controller 4, Base address 203000 */
 546 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 547 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 548 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 549 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 550 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 551 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 552 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 553
 554 #ifdef CONFIG_PCI
 555 #define CONFIG_PCI_INDIRECT_BRIDGE
 556 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
 557 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 558 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 559 #define CONFIG_DOS_PARTITION
 560 #endif
 561
 562 /* Qman/Bman */
 563 #ifndef CONFIG_NOBQFMAN
 564 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 565 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 566 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 567 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 568 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 569 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 570 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 571 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 572 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 573 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 574                                         CONFIG_SYS_BMAN_CENA_SIZE)
 575 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 576 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 577 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 578 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 579 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 580 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 581 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 582 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 583 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 584 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 585 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 586                                         CONFIG_SYS_QMAN_CENA_SIZE)
 587 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 588 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 589
 590 #define CONFIG_SYS_DPAA_FMAN
 591 #define CONFIG_SYS_DPAA_PME
 592 #define CONFIG_SYS_PMAN
 593 #define CONFIG_SYS_DPAA_DCE
 594 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 595 #define CONFIG_SYS_INTERLAKEN
 596
 597 /* Default address of microcode for the Linux Fman driver */
 598 #if defined(CONFIG_SPIFLASH)
 599 /*
 600  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 601  * env, so we got 0x110000.
 602  */
 603 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 604 #define CONFIG_SYS_CORTINA_FW_IN_SPIFLASH
 605 #define CONFIG_SYS_FMAN_FW_ADDR         0x110000
 606 #define CONFIG_CORTINA_FW_ADDR          0x120000
 607
 608 #elif defined(CONFIG_SDCARD)
 609 /*
 610  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 611  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 612  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 613  */
 614 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 615 #define CONFIG_SYS_CORTINA_FW_IN_MMC
 616 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
 617 #define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)
 618
 619 #elif defined(CONFIG_NAND)
 620 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 621 #define CONFIG_SYS_CORTINA_FW_IN_NAND
 622 #define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
 623 #define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
 624 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 625 /*
 626  * Slave has no ucode locally, it can fetch this from remote. When implementing
 627  * in two corenet boards, slave's ucode could be stored in master's memory
 628  * space, the address can be mapped from slave TLB->slave LAW->
 629  * slave SRIO or PCIE outbound window->master inbound window->
 630  * master LAW->the ucode address in master's memory space.
 631  */
 632 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 633 #define CONFIG_SYS_CORTINA_FW_IN_REMOTE
 634 #define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
 635 #define CONFIG_CORTINA_FW_ADDR          0xFFE10000
 636 #else
 637 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 638 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 639 #define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
 640 #define CONFIG_CORTINA_FW_ADDR          0xEFE00000
 641 #endif
 642 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 643 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 644 #endif /* CONFIG_NOBQFMAN */
 645
 646 #ifdef CONFIG_SYS_DPAA_FMAN
 647 #define CONFIG_FMAN_ENET
 648 #define CONFIG_PHYLIB_10G
 649 #define CONFIG_PHY_AQUANTIA
 650 #define CONFIG_PHY_CORTINA
 651 #define CONFIG_PHY_REALTEK
 652 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 653 #define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
 654 #define RGMII_PHY2_ADDR         0x02
 655 #define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
 656 #define CORTINA_PHY_ADDR2       0x0d
 657 #define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
 658 #define FM1_10GEC4_PHY_ADDR     0x01
 659 #endif
 660
 661
 662 #ifdef CONFIG_FMAN_ENET
 663 #define CONFIG_MII              /* MII PHY management */
 664 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 665 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 666 #endif
 667
 668 /*
 669  * SATA
 670  */
 671 #ifdef CONFIG_FSL_SATA_V2
 672 #define CONFIG_LIBATA
 673 #define CONFIG_FSL_SATA
 674 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 675 #define CONFIG_SATA1
 676 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 677 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 678 #define CONFIG_SATA2
 679 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 680 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 681 #define CONFIG_LBA48
 682 #define CONFIG_CMD_SATA
 683 #define CONFIG_DOS_PARTITION
 684 #define CONFIG_CMD_EXT2
 685 #endif
 686
 687 /*
 688  * USB
 689  */
 690 #ifdef CONFIG_USB_EHCI
 691 #define CONFIG_CMD_USB
 692 #define CONFIG_USB_STORAGE
 693 #define CONFIG_USB_EHCI_FSL
 694 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 695 #define CONFIG_CMD_EXT2
 696 #define CONFIG_HAS_FSL_DR_USB
 697 #endif
 698
 699 /*
 700  * SDHC
 701  */
 702 #ifdef CONFIG_MMC
 703 #define CONFIG_CMD_MMC
 704 #define CONFIG_FSL_ESDHC
 705 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 706 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 707 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 708 #define CONFIG_GENERIC_MMC
 709 #define CONFIG_CMD_EXT2
 710 #define CONFIG_CMD_FAT
 711 #define CONFIG_DOS_PARTITION
 712 #endif
 713
 714 /*
 715  * Dynamic MTD Partition support with mtdparts
 716  */
 717 #ifndef CONFIG_SYS_NO_FLASH
 718 #define CONFIG_MTD_DEVICE
 719 #define CONFIG_MTD_PARTITIONS
 720 #define CONFIG_CMD_MTDPARTS
 721 #define CONFIG_FLASH_CFI_MTD
 722 #define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
 723                         "spi0=spife110000.1"
 724 #define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
 725                         "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
 726                         "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.1:" \
 727                         "1m(uboot),5m(kernel),128k(dtb),-(user)"
 728 #endif
 729
 730 /*
 731  * Environment
 732  */
 733
 734 /*
 735  * Command line configuration.
 736  */
 737 #define CONFIG_CMD_DHCP
 738 #define CONFIG_CMD_ERRATA
 739 #define CONFIG_CMD_MII
 740 #define CONFIG_CMD_I2C
 741 #define CONFIG_CMD_PING
 742 #define CONFIG_CMD_REGINFO
 743
 744 #ifdef CONFIG_PCI
 745 #define CONFIG_CMD_PCI
 746 #endif
 747
 748 /* Hash command with SHA acceleration supported in hardware */
 749 #ifdef CONFIG_FSL_CAAM
 750 #define CONFIG_CMD_HASH
 751 #define CONFIG_SHA_HW_ACCEL
 752 #endif
 753
 754 /*
 755  * Miscellaneous configurable options
 756  */
 757 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 758 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 759 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 760 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 761 #ifdef CONFIG_CMD_KGDB
 762 #define CONFIG_SYS_CBSIZE       1024      /* Console I/O Buffer Size */
 763 #else
 764 #define CONFIG_SYS_CBSIZE       256       /* Console I/O Buffer Size */
 765 #endif
 766 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 767 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 768 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 769
 770 /*
 771  * For booting Linux, the board info and command line data
 772  * have to be in the first 64 MB of memory, since this is
 773  * the maximum mapped by the Linux kernel during initialization.
 774  */
 775 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 776 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 777
 778 #ifdef CONFIG_CMD_KGDB
 779 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 780 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 781 #endif
 782
 783 /*
 784  * Environment Configuration
 785  */
 786 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 787 #define CONFIG_BOOTFILE  "uImage"
 788 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 789
 790 /* default location for tftp and bootm */
 791 #define CONFIG_LOADADDR         1000000
 792 #define CONFIG_BAUDRATE         115200
 793 #define CONFIG_BOOTDELAY        10      /* -1 disables auto-boot */
 794 #define __USB_PHY_TYPE          utmi
 795
 796 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 797         "hwconfig=fsl_ddr:"                                     \
 798         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 799         "bank_intlv=auto;"                                      \
 800         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 801         "netdev=eth0\0"                                         \
 802         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 803         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 804         "tftpflash=tftpboot $loadaddr $uboot && "               \
 805         "protect off $ubootaddr +$filesize && "                 \
 806         "erase $ubootaddr +$filesize && "                       \
 807         "cp.b $loadaddr $ubootaddr $filesize && "               \
 808         "protect on $ubootaddr +$filesize && "                  \
 809         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 810         "consoledev=ttyS0\0"                                    \
 811         "ramdiskaddr=2000000\0"                                 \
 812         "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
 813         "fdtaddr=c00000\0"                                      \
 814         "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
 815         "bdev=sda3\0"
 816
 817 /*
 818  * For emulation this causes u-boot to jump to the start of the
 819  * proof point app code automatically
 820  */
 821 #define CONFIG_PROOF_POINTS                             \
 822         "setenv bootargs root=/dev/$bdev rw "           \
 823         "console=$consoledev,$baudrate $othbootargs;"   \
 824         "cpu 1 release 0x29000000 - - -;"               \
 825         "cpu 2 release 0x29000000 - - -;"               \
 826         "cpu 3 release 0x29000000 - - -;"               \
 827         "cpu 4 release 0x29000000 - - -;"               \
 828         "cpu 5 release 0x29000000 - - -;"               \
 829         "cpu 6 release 0x29000000 - - -;"               \
 830         "cpu 7 release 0x29000000 - - -;"               \
 831         "go 0x29000000"
 832
 833 #define CONFIG_HVBOOT                           \
 834         "setenv bootargs config-addr=0x60000000; "      \
 835         "bootm 0x01000000 - 0x00f00000"
 836
 837 #define CONFIG_ALU                              \
 838         "setenv bootargs root=/dev/$bdev rw "           \
 839         "console=$consoledev,$baudrate $othbootargs;"   \
 840         "cpu 1 release 0x01000000 - - -;"               \
 841         "cpu 2 release 0x01000000 - - -;"               \
 842         "cpu 3 release 0x01000000 - - -;"               \
 843         "cpu 4 release 0x01000000 - - -;"               \
 844         "cpu 5 release 0x01000000 - - -;"               \
 845         "cpu 6 release 0x01000000 - - -;"               \
 846         "cpu 7 release 0x01000000 - - -;"               \
 847         "go 0x01000000"
 848
 849 #define CONFIG_LINUX                            \
 850         "setenv bootargs root=/dev/ram rw "             \
 851         "console=$consoledev,$baudrate $othbootargs;"   \
 852         "setenv ramdiskaddr 0x02000000;"                \
 853         "setenv fdtaddr 0x00c00000;"                    \
 854         "setenv loadaddr 0x1000000;"                    \
 855         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 856
 857 #define CONFIG_HDBOOT                                   \
 858         "setenv bootargs root=/dev/$bdev rw "           \
 859         "console=$consoledev,$baudrate $othbootargs;"   \
 860         "tftp $loadaddr $bootfile;"                     \
 861         "tftp $fdtaddr $fdtfile;"                       \
 862         "bootm $loadaddr - $fdtaddr"
 863
 864 #define CONFIG_NFSBOOTCOMMAND                   \
 865         "setenv bootargs root=/dev/nfs rw "     \
 866         "nfsroot=$serverip:$rootpath "          \
 867         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 868         "console=$consoledev,$baudrate $othbootargs;"   \
 869         "tftp $loadaddr $bootfile;"             \
 870         "tftp $fdtaddr $fdtfile;"               \
 871         "bootm $loadaddr - $fdtaddr"
 872
 873 #define CONFIG_RAMBOOTCOMMAND                           \
 874         "setenv bootargs root=/dev/ram rw "             \
 875         "console=$consoledev,$baudrate $othbootargs;"   \
 876         "tftp $ramdiskaddr $ramdiskfile;"               \
 877         "tftp $loadaddr $bootfile;"                     \
 878         "tftp $fdtaddr $fdtfile;"                       \
 879         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 880
 881 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 882
 883 #include <asm/fsl_secure_boot.h>
 884
 885 #endif  /* __T2080RDB_H */