include/configs/TQM855M.h

   1 /*
   2  * (C) Copyright 2000-2014
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /*
  16  * High Level Configuration Options
  17  * (easy to change)
  18  */
  19
  20 #define CONFIG_MPC855           1       /* This is a MPC855 CPU         */
  21 #define CONFIG_TQM855M          1       /* ...on a TQM8xxM module       */
  22
  23 #define CONFIG_SYS_TEXT_BASE    0x40000000
  24
  25 #define CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
  26 #define CONFIG_SYS_SMC_RXBUFLEN 128
  27 #define CONFIG_SYS_MAXIDLE      10
  28
  29 #define CONFIG_BOOTCOUNT_LIMIT
  30
  31
  32 #define CONFIG_BOARD_TYPES      1       /* support board types          */
  33
  34 #define CONFIG_PREBOOT  "echo;" \
  35         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
  36         "echo"
  37
  38 #undef  CONFIG_BOOTARGS
  39
  40 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  41         "netdev=eth0\0"                                                 \
  42         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
  43                 "nfsroot=${serverip}:${rootpath}\0"                     \
  44         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
  45         "addip=setenv bootargs ${bootargs} "                            \
  46                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  47                 ":${hostname}:${netdev}:off panic=1\0"                  \
  48         "flash_nfs=run nfsargs addip;"                                  \
  49                 "bootm ${kernel_addr}\0"                                \
  50         "flash_self=run ramargs addip;"                                 \
  51                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  52         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
  53         "rootpath=/opt/eldk/ppc_8xx\0"                                  \
  54         "hostname=TQM855M\0"                                            \
  55         "bootfile=TQM855M/uImage\0"                                     \
  56         "fdt_addr=40080000\0"                                           \
  57         "kernel_addr=400A0000\0"                                        \
  58         "ramdisk_addr=40280000\0"                                       \
  59         "u-boot=TQM855M/u-image.bin\0"                                  \
  60         "load=tftp 200000 ${u-boot}\0"                                  \
  61         "update=prot off 40000000 +${filesize};"                        \
  62                 "era 40000000 +${filesize};"                            \
  63                 "cp.b 200000 40000000 ${filesize};"                     \
  64                 "sete filesize;save\0"                                  \
  65         ""
  66 #define CONFIG_BOOTCOMMAND      "run flash_self"
  67
  68 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
  69 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
  70
  71 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  72
  73 #undef  CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
  74
  75 /* enable I2C and select the hardware/software driver */
  76 #define CONFIG_SYS_I2C
  77 #define CONFIG_SYS_I2C_SOFT             /* I2C bit-banged */
  78 #define CONFIG_SYS_I2C_SOFT_SPEED       93000   /* 93 kHz is supposed to work */
  79 #define CONFIG_SYS_I2C_SOFT_SLAVE       0xFE
  80 /*
  81  * Software (bit-bang) I2C driver configuration
  82  */
  83 #define PB_SCL          0x00000020      /* PB 26 */
  84 #define PB_SDA          0x00000010      /* PB 27 */
  85
  86 #define I2C_INIT        (immr->im_cpm.cp_pbdir |=  PB_SCL)
  87 #define I2C_ACTIVE      (immr->im_cpm.cp_pbdir |=  PB_SDA)
  88 #define I2C_TRISTATE    (immr->im_cpm.cp_pbdir &= ~PB_SDA)
  89 #define I2C_READ        ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
  90 #define I2C_SDA(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
  91                         else    immr->im_cpm.cp_pbdat &= ~PB_SDA
  92 #define I2C_SCL(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
  93                         else    immr->im_cpm.cp_pbdat &= ~PB_SCL
  94 #define I2C_DELAY       udelay(2)       /* 1/4 I2C clock duration */
  95
  96 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* EEPROM AT24C64       */
  97 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2               /* two byte address     */
  98 #if 0
  99 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* takes up to 10 msec  */
 100 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
 101 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       5
 102 #endif
 103
 104 /*
 105  * BOOTP options
 106  */
 107 #define CONFIG_BOOTP_SUBNETMASK
 108 #define CONFIG_BOOTP_GATEWAY
 109 #define CONFIG_BOOTP_HOSTNAME
 110 #define CONFIG_BOOTP_BOOTPATH
 111 #define CONFIG_BOOTP_BOOTFILESIZE
 112
 113 #define CONFIG_RTC_MPC8xx               /* use internal RTC of MPC8xx   */
 114
 115 /*
 116  * Command line configuration.
 117  */
 118 #define CONFIG_CMD_EEPROM
 119 #define CONFIG_CMD_IDE
 120 #define CONFIG_CMD_JFFS2
 121
 122 #define CONFIG_NETCONSOLE
 123
 124 /*
 125  * Miscellaneous configurable options
 126  */
 127 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 128
 129 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 130
 131 #if defined(CONFIG_CMD_KGDB)
 132 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
 133 #else
 134 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
 135 #endif
 136 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 137 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 138 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 139
 140 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 141 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 142
 143 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 144
 145 /*
 146  * Low Level Configuration Settings
 147  * (address mappings, register initial values, etc.)
 148  * You should know what you are doing if you make changes here.
 149  */
 150 /*-----------------------------------------------------------------------
 151  * Internal Memory Mapped Register
 152  */
 153 #define CONFIG_SYS_IMMR         0xFFF00000
 154
 155 /*-----------------------------------------------------------------------
 156  * Definitions for initial stack pointer and data area (in DPRAM)
 157  */
 158 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 159 #define CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
 160 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 161 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 162
 163 /*-----------------------------------------------------------------------
 164  * Start addresses for the final memory configuration
 165  * (Set up by the startup code)
 166  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 167  */
 168 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 169 #define CONFIG_SYS_FLASH_BASE           0x40000000
 170 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 171 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 172 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 173
 174 /*
 175  * For booting Linux, the board info and command line data
 176  * have to be in the first 8 MB of memory, since this is
 177  * the maximum mapped by the Linux kernel during initialization.
 178  */
 179 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 180
 181 /*-----------------------------------------------------------------------
 182  * FLASH organization
 183  */
 184
 185 /* use CFI flash driver */
 186 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 187 #define CONFIG_FLASH_CFI_DRIVER 1       /* Use the common driver */
 188 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 189 #define CONFIG_SYS_FLASH_EMPTY_INFO
 190 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 191 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
 192 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */
 193
 194 #define CONFIG_ENV_IS_IN_FLASH  1
 195 #define CONFIG_ENV_OFFSET               0x40000 /*   Offset   of Environment Sector     */
 196 #define CONFIG_ENV_SIZE         0x08000 /* Total Size of Environment            */
 197 #define CONFIG_ENV_SECT_SIZE    0x20000 /* Total Size of Environment Sector     */
 198
 199 /* Address and size of Redundant Environment Sector     */
 200 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 201 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 202
 203 #define CONFIG_SYS_USE_PPCENV                   /* Environment embedded in sect .ppcenv */
 204
 205 #define CONFIG_MISC_INIT_R              /* Make sure to remap flashes correctly */
 206
 207 /*-----------------------------------------------------------------------
 208  * Dynamic MTD partition support
 209  */
 210 #define CONFIG_CMD_MTDPARTS
 211 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 212 #define CONFIG_FLASH_CFI_MTD
 213 #define MTDIDS_DEFAULT          "nor0=TQM8xxM-0"
 214
 215 #define MTDPARTS_DEFAULT        "mtdparts=TQM8xxM-0:512k(u-boot),"      \
 216                                                 "128k(dtb),"            \
 217                                                 "1920k(kernel),"        \
 218                                                 "5632(rootfs),"         \
 219                                                 "4m(data)"
 220
 221 /*-----------------------------------------------------------------------
 222  * Hardware Information Block
 223  */
 224 #define CONFIG_SYS_HWINFO_OFFSET        0x0003FFC0      /* offset of HW Info block */
 225 #define CONFIG_SYS_HWINFO_SIZE          0x00000040      /* size   of HW Info block */
 226 #define CONFIG_SYS_HWINFO_MAGIC 0x54514D38      /* 'TQM8' */
 227
 228 /*-----------------------------------------------------------------------
 229  * Cache Configuration
 230  */
 231 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 232 #if defined(CONFIG_CMD_KGDB)
 233 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 234 #endif
 235
 236 /*-----------------------------------------------------------------------
 237  * SYPCR - System Protection Control                            11-9
 238  * SYPCR can only be written once after reset!
 239  *-----------------------------------------------------------------------
 240  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 241  */
 242 #if defined(CONFIG_WATCHDOG)
 243 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 244                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 245 #else
 246 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 247 #endif
 248
 249 /*-----------------------------------------------------------------------
 250  * SIUMCR - SIU Module Configuration                            11-6
 251  *-----------------------------------------------------------------------
 252  * PCMCIA config., multi-function pin tri-state
 253  */
 254 #ifndef CONFIG_CAN_DRIVER
 255 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 256 #else   /* we must activate GPL5 in the SIUMCR for CAN */
 257 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 258 #endif  /* CONFIG_CAN_DRIVER */
 259
 260 /*-----------------------------------------------------------------------
 261  * TBSCR - Time Base Status and Control                         11-26
 262  *-----------------------------------------------------------------------
 263  * Clear Reference Interrupt Status, Timebase freezing enabled
 264  */
 265 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 266
 267 /*-----------------------------------------------------------------------
 268  * RTCSC - Real-Time Clock Status and Control Register          11-27
 269  *-----------------------------------------------------------------------
 270  */
 271 #define CONFIG_SYS_RTCSC        (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
 272
 273 /*-----------------------------------------------------------------------
 274  * PISCR - Periodic Interrupt Status and Control                11-31
 275  *-----------------------------------------------------------------------
 276  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 277  */
 278 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF)
 279
 280 /*-----------------------------------------------------------------------
 281  * PLPRCR - PLL, Low-Power, and Reset Control Register          15-30
 282  *-----------------------------------------------------------------------
 283  * Reset PLL lock status sticky bit, timer expired status bit and timer
 284  * interrupt status bit
 285  */
 286 #define CONFIG_SYS_PLPRCR       (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
 287
 288 /*-----------------------------------------------------------------------
 289  * SCCR - System Clock and reset Control Register               15-27
 290  *-----------------------------------------------------------------------
 291  * Set clock output, timebase and RTC source and divider,
 292  * power management and some other internal clocks
 293  */
 294 #define SCCR_MASK       SCCR_EBDF11
 295 #define CONFIG_SYS_SCCR (SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 296                          SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 297                          SCCR_DFALCD00)
 298
 299 /*-----------------------------------------------------------------------
 300  * PCMCIA stuff
 301  *-----------------------------------------------------------------------
 302  *
 303  */
 304 #define CONFIG_SYS_PCMCIA_MEM_ADDR      (0xE0000000)
 305 #define CONFIG_SYS_PCMCIA_MEM_SIZE      ( 64 << 20 )
 306 #define CONFIG_SYS_PCMCIA_DMA_ADDR      (0xE4000000)
 307 #define CONFIG_SYS_PCMCIA_DMA_SIZE      ( 64 << 20 )
 308 #define CONFIG_SYS_PCMCIA_ATTRB_ADDR    (0xE8000000)
 309 #define CONFIG_SYS_PCMCIA_ATTRB_SIZE    ( 64 << 20 )
 310 #define CONFIG_SYS_PCMCIA_IO_ADDR       (0xEC000000)
 311 #define CONFIG_SYS_PCMCIA_IO_SIZE       ( 64 << 20 )
 312
 313 /*-----------------------------------------------------------------------
 314  * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 315  *-----------------------------------------------------------------------
 316  */
 317
 318 #define CONFIG_IDE_PREINIT      1       /* Use preinit IDE hook */
 319 #define CONFIG_IDE_8xx_PCCARD   1       /* Use IDE with PC Card Adapter */
 320
 321 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 322 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 323 #undef  CONFIG_IDE_RESET                /* reset for ide not supported  */
 324
 325 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 326 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 1 drive per IDE bus     */
 327
 328 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 329
 330 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_PCMCIA_MEM_ADDR
 331
 332 /* Offset for data I/O                  */
 333 #define CONFIG_SYS_ATA_DATA_OFFSET      (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 334
 335 /* Offset for normal register accesses  */
 336 #define CONFIG_SYS_ATA_REG_OFFSET       (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 337
 338 /* Offset for alternate registers       */
 339 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0100
 340
 341 /*-----------------------------------------------------------------------
 342  *
 343  *-----------------------------------------------------------------------
 344  *
 345  */
 346 #define CONFIG_SYS_DER  0
 347
 348 /*
 349  * Init Memory Controller:
 350  *
 351  * BR0/1 and OR0/1 (FLASH)
 352  */
 353
 354 #define FLASH_BASE0_PRELIM      0x40000000      /* FLASH bank #0        */
 355 #define FLASH_BASE1_PRELIM      0x60000000      /* FLASH bank #0        */
 356
 357 /* used to re-map FLASH both when starting from SRAM or FLASH:
 358  * restrict access enough to keep SRAM working (if any)
 359  * but not too much to meddle with FLASH accesses
 360  */
 361 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 362 #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000      /* OR addr mask */
 363
 364 /*
 365  * FLASH timing:
 366  */
 367 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 368                                  OR_SCY_3_CLK | OR_EHTR | OR_BI)
 369
 370 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 371 #define CONFIG_SYS_OR0_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 372 #define CONFIG_SYS_BR0_PRELIM   ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
 373
 374 #define CONFIG_SYS_OR1_REMAP    CONFIG_SYS_OR0_REMAP
 375 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 376 #define CONFIG_SYS_BR1_PRELIM   ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
 377
 378 /*
 379  * BR2/3 and OR2/3 (SDRAM)
 380  *
 381  */
 382 #define SDRAM_BASE2_PRELIM      0x00000000      /* SDRAM bank #0        */
 383 #define SDRAM_BASE3_PRELIM      0x20000000      /* SDRAM bank #1        */
 384 #define SDRAM_MAX_SIZE          0x04000000      /* max 64 MB per bank   */
 385
 386 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)      */
 387 #define CONFIG_SYS_OR_TIMING_SDRAM      0x00000A00
 388
 389 #define CONFIG_SYS_OR2_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
 390 #define CONFIG_SYS_BR2_PRELIM   ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 391
 392 #ifndef CONFIG_CAN_DRIVER
 393 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 394 #define CONFIG_SYS_BR3_PRELIM   ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 395 #else   /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
 396 #define CONFIG_SYS_CAN_BASE             0xC0000000      /* CAN mapped at 0xC0000000     */
 397 #define CONFIG_SYS_CAN_OR_AM            0xFFFF8000      /* 32 kB address mask           */
 398 #define CONFIG_SYS_OR3_CAN              (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
 399 #define CONFIG_SYS_BR3_CAN              ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
 400                                         BR_PS_8 | BR_MS_UPMB | BR_V )
 401 #endif  /* CONFIG_CAN_DRIVER */
 402
 403 /*
 404  * Memory Periodic Timer Prescaler
 405  *
 406  * The Divider for PTA (refresh timer) configuration is based on an
 407  * example SDRAM configuration (64 MBit, one bank). The adjustment to
 408  * the number of chip selects (NCS) and the actually needed refresh
 409  * rate is done by setting MPTPR.
 410  *
 411  * PTA is calculated from
 412  *      PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
 413  *
 414  *      gclk      CPU clock (not bus clock!)
 415  *      Trefresh  Refresh cycle * 4 (four word bursts used)
 416  *
 417  * 4096  Rows from SDRAM example configuration
 418  * 1000  factor s -> ms
 419  *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
 420  *    4  Number of refresh cycles per period
 421  *   64  Refresh cycle in ms per number of rows
 422  * --------------------------------------------
 423  * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
 424  *
 425  * 50 MHz => 50.000.000 / Divider =  98
 426  * 66 Mhz => 66.000.000 / Divider = 129
 427  * 80 Mhz => 80.000.000 / Divider = 156
 428  */
 429
 430 #define CONFIG_SYS_PTA_PER_CLK  ((4096 * 32 * 1000) / (4 * 64))
 431 #define CONFIG_SYS_MAMR_PTA     98
 432
 433 /*
 434  * For 16 MBit, refresh rates could be 31.3 us
 435  * (= 64 ms / 2K = 125 / quad bursts).
 436  * For a simpler initialization, 15.6 us is used instead.
 437  *
 438  * #define CONFIG_SYS_MPTPR_2BK_2K      MPTPR_PTP_DIV32         for 2 banks
 439  * #define CONFIG_SYS_MPTPR_1BK_2K      MPTPR_PTP_DIV64         for 1 bank
 440  */
 441 #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16         /* setting for 2 banks  */
 442 #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32         /* setting for 1 bank   */
 443
 444 /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit         */
 445 #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8          /* setting for 2 banks  */
 446 #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16         /* setting for 1 bank   */
 447
 448 /*
 449  * MAMR settings for SDRAM
 450  */
 451
 452 /* 8 column SDRAM */
 453 #define CONFIG_SYS_MAMR_8COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 454                          MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
 455                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 456 /* 9 column SDRAM */
 457 #define CONFIG_SYS_MAMR_9COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 458                          MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
 459                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 460
 461 #define CONFIG_SCC1_ENET
 462 #define CONFIG_FEC_ENET
 463 #define CONFIG_ETHPRIME         "SCC"
 464
 465 #define CONFIG_HWCONFIG         1
 466
 467 #endif  /* __CONFIG_H */