include/configs/TQM866M.h

   1 /*
   2  * (C) Copyright 2000-2014
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /*
  16  * High Level Configuration Options
  17  * (easy to change)
  18  */
  19
  20 #define CONFIG_MPC866           1       /* This is a MPC866 CPU         */
  21 #define CONFIG_TQM866M          1       /* ...on a TQM8xxM module       */
  22
  23 #define CONFIG_SYS_TEXT_BASE    0x40000000
  24
  25 #define CONFIG_8xx_OSCLK                10000000        /*  10 MHz - PLL input clock    */
  26 #define CONFIG_SYS_8xx_CPUCLK_MIN               15000000        /*  15 MHz - CPU minimum clock  */
  27 #define CONFIG_SYS_8xx_CPUCLK_MAX               133000000       /* 133 MHz - CPU maximum clock  */
  28 #define CONFIG_8xx_CPUCLK_DEFAULT       50000000        /*  50 MHz - CPU default clock  */
  29                                                 /* (it will be used if there is no      */
  30                                                 /* 'cpuclk' variable with valid value)  */
  31
  32 #undef CONFIG_SYS_MEASURE_CPUCLK                        /* Measure real cpu clock       */
  33                                                 /* (function measure_gclk()     */
  34                                                 /* will be called)              */
  35 #ifdef CONFIG_SYS_MEASURE_CPUCLK
  36 #define CONFIG_SYS_8XX_XIN              10000000        /* measure_gclk() needs this    */
  37 #endif
  38
  39 #define CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
  40 #define CONFIG_SYS_SMC_RXBUFLEN 128
  41 #define CONFIG_SYS_MAXIDLE      10
  42
  43 #define CONFIG_BOOTCOUNT_LIMIT
  44
  45
  46 #define CONFIG_BOARD_TYPES      1       /* support board types          */
  47
  48 #define CONFIG_PREBOOT  "echo;" \
  49         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
  50         "echo"
  51
  52 #undef  CONFIG_BOOTARGS
  53
  54 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  55         "netdev=eth0\0"                                                 \
  56         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
  57                 "nfsroot=${serverip}:${rootpath}\0"                     \
  58         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
  59         "addip=setenv bootargs ${bootargs} "                            \
  60                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  61                 ":${hostname}:${netdev}:off panic=1\0"                  \
  62         "flash_nfs=run nfsargs addip;"                                  \
  63                 "bootm ${kernel_addr}\0"                                \
  64         "flash_self=run ramargs addip;"                                 \
  65                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  66         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
  67         "rootpath=/opt/eldk/ppc_8xx\0"                                  \
  68         "hostname=TQM866M\0"                                            \
  69         "bootfile=TQM866M/uImage\0"                                     \
  70         "fdt_addr=400C0000\0"                                           \
  71         "kernel_addr=40100000\0"                                        \
  72         "ramdisk_addr=40280000\0"                                       \
  73         "u-boot=TQM866M/u-image.bin\0"                                  \
  74         "load=tftp 200000 ${u-boot}\0"                                  \
  75         "update=prot off 40000000 +${filesize};"                        \
  76                 "era 40000000 +${filesize};"                            \
  77                 "cp.b 200000 40000000 ${filesize};"                     \
  78                 "sete filesize;save\0"                                  \
  79         ""
  80 #define CONFIG_BOOTCOMMAND      "run flash_self"
  81
  82 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
  83 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
  84
  85 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  86
  87 #undef  CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
  88
  89 /* enable I2C and select the hardware/software driver */
  90 #define CONFIG_SYS_I2C
  91 #define CONFIG_SYS_I2C_SOFT                     /* I2C bit-banged */
  92 #define CONFIG_SYS_I2C_SOFT_SPEED       93000   /* 93 kHz is supposed to work */
  93 #define CONFIG_SYS_I2C_SOFT_SLAVE       0xFE
  94
  95 /*
  96  * Software (bit-bang) I2C driver configuration
  97  */
  98 #define PB_SCL          0x00000020      /* PB 26 */
  99 #define PB_SDA          0x00000010      /* PB 27 */
 100
 101 #define I2C_INIT        (immr->im_cpm.cp_pbdir |=  PB_SCL)
 102 #define I2C_ACTIVE      (immr->im_cpm.cp_pbdir |=  PB_SDA)
 103 #define I2C_TRISTATE    (immr->im_cpm.cp_pbdir &= ~PB_SDA)
 104 #define I2C_READ        ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 105 #define I2C_SDA(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
 106                         else    immr->im_cpm.cp_pbdat &= ~PB_SDA
 107 #define I2C_SCL(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 108                         else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 109 #define I2C_DELAY       udelay(2)       /* 1/4 I2C clock duration */
 110
 111 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* EEPROM AT24C256      */
 112 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2                /* two byte address     */
 113 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 114 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
 115
 116 /*
 117  * BOOTP options
 118  */
 119 #define CONFIG_BOOTP_SUBNETMASK
 120 #define CONFIG_BOOTP_GATEWAY
 121 #define CONFIG_BOOTP_HOSTNAME
 122 #define CONFIG_BOOTP_BOOTPATH
 123 #define CONFIG_BOOTP_BOOTFILESIZE
 124
 125 #undef CONFIG_RTC_MPC8xx                /* MPC866 does not support RTC  */
 126
 127 #define CONFIG_TIMESTAMP                /* but print image timestmps    */
 128
 129 /*
 130  * Command line configuration.
 131  */
 132 #define CONFIG_CMD_JFFS2
 133
 134 #define CONFIG_NETCONSOLE
 135
 136 /*
 137  * Miscellaneous configurable options
 138  */
 139 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 140
 141 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 142
 143 #if defined(CONFIG_CMD_KGDB)
 144 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
 145 #else
 146 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
 147 #endif
 148 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 149 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 150 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 151
 152 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 153 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 154
 155 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 156
 157 /*
 158  * Low Level Configuration Settings
 159  * (address mappings, register initial values, etc.)
 160  * You should know what you are doing if you make changes here.
 161  */
 162 /*-----------------------------------------------------------------------
 163  * Internal Memory Mapped Register
 164  */
 165 #define CONFIG_SYS_IMMR         0xFFF00000
 166
 167 /*-----------------------------------------------------------------------
 168  * Definitions for initial stack pointer and data area (in DPRAM)
 169  */
 170 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 171 #define CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
 172 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 173 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 174
 175 /*-----------------------------------------------------------------------
 176  * Start addresses for the final memory configuration
 177  * (Set up by the startup code)
 178  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 179  */
 180 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 181 #define CONFIG_SYS_FLASH_BASE           0x40000000
 182 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 183 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 184 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* Reserve 256 kB for malloc()  */
 185
 186 /*
 187  * For booting Linux, the board info and command line data
 188  * have to be in the first 8 MB of memory, since this is
 189  * the maximum mapped by the Linux kernel during initialization.
 190  */
 191 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 192
 193 /*-----------------------------------------------------------------------
 194  * FLASH organization
 195  */
 196 /* use CFI flash driver */
 197 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 198 #define CONFIG_FLASH_CFI_DRIVER 1       /* Use the common driver */
 199 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 200 #define CONFIG_SYS_FLASH_EMPTY_INFO
 201 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 202 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
 203 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */
 204
 205 #define CONFIG_ENV_IS_IN_FLASH  1
 206 #define CONFIG_ENV_OFFSET               0x40000 /*   Offset   of Environment Sector     */
 207 #define CONFIG_ENV_SIZE         0x08000 /* Total Size of Environment Sector     */
 208 #define CONFIG_ENV_SECT_SIZE    0x40000 /* Total Size of Environment Sector     */
 209
 210 /* Address and size of Redundant Environment Sector     */
 211 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 212 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 213
 214 #define CONFIG_SYS_USE_PPCENV                   /* Environment embedded in sect .ppcenv */
 215
 216 #define CONFIG_MISC_INIT_R              /* Make sure to remap flashes correctly */
 217
 218 /*-----------------------------------------------------------------------
 219  * Dynamic MTD partition support
 220  */
 221 #define CONFIG_CMD_MTDPARTS
 222 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 223 #define CONFIG_FLASH_CFI_MTD
 224 #define MTDIDS_DEFAULT          "nor0=TQM8xxM-0"
 225
 226 #define MTDPARTS_DEFAULT        "mtdparts=TQM8xxM-0:512k(u-boot),"      \
 227                                                 "128k(dtb),"            \
 228                                                 "1920k(kernel),"        \
 229                                                 "5632(rootfs),"         \
 230                                                 "4m(data)"
 231
 232 /*-----------------------------------------------------------------------
 233  * Hardware Information Block
 234  */
 235 #define CONFIG_SYS_HWINFO_OFFSET        0x0003FFC0      /* offset of HW Info block */
 236 #define CONFIG_SYS_HWINFO_SIZE          0x00000040      /* size   of HW Info block */
 237 #define CONFIG_SYS_HWINFO_MAGIC 0x54514D38      /* 'TQM8' */
 238
 239 /*-----------------------------------------------------------------------
 240  * Cache Configuration
 241  */
 242 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 243 #if defined(CONFIG_CMD_KGDB)
 244 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 245 #endif
 246
 247 /*-----------------------------------------------------------------------
 248  * SYPCR - System Protection Control                            11-9
 249  * SYPCR can only be written once after reset!
 250  *-----------------------------------------------------------------------
 251  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 252  */
 253 #if defined(CONFIG_WATCHDOG)
 254 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 255                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 256 #else
 257 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 258 #endif
 259
 260 /*-----------------------------------------------------------------------
 261  * SIUMCR - SIU Module Configuration                            11-6
 262  *-----------------------------------------------------------------------
 263  * PCMCIA config., multi-function pin tri-state
 264  */
 265 #ifndef CONFIG_CAN_DRIVER
 266 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 267 #else   /* we must activate GPL5 in the SIUMCR for CAN */
 268 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 269 #endif  /* CONFIG_CAN_DRIVER */
 270
 271 /*-----------------------------------------------------------------------
 272  * TBSCR - Time Base Status and Control                         11-26
 273  *-----------------------------------------------------------------------
 274  * Clear Reference Interrupt Status, Timebase freezing enabled
 275  */
 276 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 277
 278 /*-----------------------------------------------------------------------
 279  * PISCR - Periodic Interrupt Status and Control                11-31
 280  *-----------------------------------------------------------------------
 281  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 282  */
 283 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF)
 284
 285 /*-----------------------------------------------------------------------
 286  * SCCR - System Clock and reset Control Register               15-27
 287  *-----------------------------------------------------------------------
 288  * Set clock output, timebase and RTC source and divider,
 289  * power management and some other internal clocks
 290  */
 291 #define SCCR_MASK       SCCR_EBDF11
 292 #define CONFIG_SYS_SCCR (SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 293                          SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 294                          SCCR_DFALCD00)
 295
 296 /*-----------------------------------------------------------------------
 297  * PCMCIA stuff
 298  *-----------------------------------------------------------------------
 299  *
 300  */
 301 #define CONFIG_SYS_PCMCIA_MEM_ADDR      (0xE0000000)
 302 #define CONFIG_SYS_PCMCIA_MEM_SIZE      ( 64 << 20 )
 303 #define CONFIG_SYS_PCMCIA_DMA_ADDR      (0xE4000000)
 304 #define CONFIG_SYS_PCMCIA_DMA_SIZE      ( 64 << 20 )
 305 #define CONFIG_SYS_PCMCIA_ATTRB_ADDR    (0xE8000000)
 306 #define CONFIG_SYS_PCMCIA_ATTRB_SIZE    ( 64 << 20 )
 307 #define CONFIG_SYS_PCMCIA_IO_ADDR       (0xEC000000)
 308 #define CONFIG_SYS_PCMCIA_IO_SIZE       ( 64 << 20 )
 309
 310 /*-----------------------------------------------------------------------
 311  * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 312  *-----------------------------------------------------------------------
 313  */
 314
 315 #define CONFIG_IDE_PREINIT      1       /* Use preinit IDE hook */
 316 #define CONFIG_IDE_8xx_PCCARD   1       /* Use IDE with PC Card Adapter */
 317
 318 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 319 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 320 #undef  CONFIG_IDE_RESET                /* reset for ide not supported  */
 321
 322 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 323 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 1 drive per IDE bus     */
 324
 325 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 326
 327 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_PCMCIA_MEM_ADDR
 328
 329 /* Offset for data I/O                  */
 330 #define CONFIG_SYS_ATA_DATA_OFFSET      (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 331
 332 /* Offset for normal register accesses  */
 333 #define CONFIG_SYS_ATA_REG_OFFSET       (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 334
 335 /* Offset for alternate registers       */
 336 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0100
 337
 338 /*-----------------------------------------------------------------------
 339  *
 340  *-----------------------------------------------------------------------
 341  *
 342  */
 343 #define CONFIG_SYS_DER 0
 344
 345 /*
 346  * Init Memory Controller:
 347  *
 348  * BR0/1 and OR0/1 (FLASH)
 349  */
 350
 351 #define FLASH_BASE0_PRELIM      0x40000000      /* FLASH bank #0        */
 352 #define FLASH_BASE1_PRELIM      0x60000000      /* FLASH bank #0        */
 353
 354 /* used to re-map FLASH both when starting from SRAM or FLASH:
 355  * restrict access enough to keep SRAM working (if any)
 356  * but not too much to meddle with FLASH accesses
 357  */
 358 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 359 #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000      /* OR addr mask */
 360
 361 /*
 362  * FLASH timing: Default value of OR0 after reset
 363  */
 364 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
 365                                  OR_SCY_15_CLK | OR_TRLX)
 366
 367 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 368 #define CONFIG_SYS_OR0_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 369 #define CONFIG_SYS_BR0_PRELIM   ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
 370
 371 #define CONFIG_SYS_OR1_REMAP    CONFIG_SYS_OR0_REMAP
 372 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 373 #define CONFIG_SYS_BR1_PRELIM   ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
 374
 375 /*
 376  * BR2/3 and OR2/3 (SDRAM)
 377  *
 378  */
 379 #define SDRAM_BASE2_PRELIM      0x00000000      /* SDRAM bank #0        */
 380 #define SDRAM_BASE3_PRELIM      0x20000000      /* SDRAM bank #1        */
 381 #define SDRAM_MAX_SIZE          (256 << 20)     /* max 256 MB per bank  */
 382
 383 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)      */
 384 #define CONFIG_SYS_OR_TIMING_SDRAM      0x00000A00
 385
 386 #define CONFIG_SYS_OR2_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
 387 #define CONFIG_SYS_BR2_PRELIM   ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 388
 389 #ifndef CONFIG_CAN_DRIVER
 390 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 391 #define CONFIG_SYS_BR3_PRELIM   ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 392 #else   /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
 393 #define CONFIG_SYS_CAN_BASE             0xC0000000      /* CAN mapped at 0xC0000000     */
 394 #define CONFIG_SYS_CAN_OR_AM            0xFFFF8000      /* 32 kB address mask           */
 395 #define CONFIG_SYS_OR3_CAN              (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
 396 #define CONFIG_SYS_BR3_CAN              ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
 397                                         BR_PS_8 | BR_MS_UPMB | BR_V )
 398 #endif  /* CONFIG_CAN_DRIVER */
 399
 400 /*
 401  * 4096 Rows from SDRAM example configuration
 402  * 1000 factor s -> ms
 403  * 64   PTP (pre-divider from MPTPR) from SDRAM example configuration
 404  * 4    Number of refresh cycles per period
 405  * 64   Refresh cycle in ms per number of rows
 406  */
 407 #define CONFIG_SYS_PTA_PER_CLK  ((4096 * 64 * 1000) / (4 * 64))
 408
 409 /*
 410  * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
 411  *
 412  *                        CPUclock(MHz) * 31.2
 413  * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
 414  *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
 415  *
 416  * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
 417  * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
 418  * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
 419  * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
 420  *
 421  * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
 422  * be met also in the default configuration, i.e. if environment variable
 423  * 'cpuclk' is not set.
 424  */
 425 #define CONFIG_SYS_MAMR_PTA             97
 426
 427 /*
 428  * Memory Periodic Timer Prescaler Register (MPTPR) values.
 429  */
 430 /* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
 431 #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16
 432 /* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
 433 #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8
 434
 435 /*
 436  * MAMR settings for SDRAM
 437  */
 438
 439 /* 8 column SDRAM */
 440 #define CONFIG_SYS_MAMR_8COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 441                          MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
 442                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 443 /* 9 column SDRAM */
 444 #define CONFIG_SYS_MAMR_9COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 445                          MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
 446                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 447 /* 10 column SDRAM */
 448 #define CONFIG_SYS_MAMR_10COL   ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 449                          MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |   \
 450                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 451
 452 #define CONFIG_SCC1_ENET
 453 #define CONFIG_FEC_ENET
 454 #define CONFIG_ETHPRIME         "SCC"
 455
 456 #define CONFIG_HWCONFIG         1
 457
 458 #endif  /* __CONFIG_H */