include/configs/TQM885D.h

   1 /*
   2  * (C) Copyright 2000-2014
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * (C) Copyright 2006
   6  * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * board/config.h - configuration options, board specific
  13  */
  14
  15 #ifndef __CONFIG_H
  16 #define __CONFIG_H
  17
  18 /*
  19  * High Level Configuration Options
  20  * (easy to change)
  21  */
  22
  23 #define CONFIG_MPC885           1       /* This is a MPC885 CPU         */
  24 #define CONFIG_TQM885D          1       /* ...on a TQM88D module        */
  25
  26 #define CONFIG_SYS_TEXT_BASE    0x40000000
  27
  28 #define CONFIG_8xx_OSCLK                10000000        /*  10 MHz - PLL input clock    */
  29 #define CONFIG_SYS_8xx_CPUCLK_MIN               15000000        /*  15 MHz - CPU minimum clock  */
  30 #define CONFIG_SYS_8xx_CPUCLK_MAX               133000000       /* 133 MHz - CPU maximum clock  */
  31 #define CONFIG_8xx_CPUCLK_DEFAULT       66000000        /*  66 MHz - CPU default clock  */
  32                                                 /* (it will be used if there is no      */
  33                                                 /* 'cpuclk' variable with valid value)  */
  34
  35 #define CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
  36 #define CONFIG_SYS_SMC_RXBUFLEN 128
  37 #define CONFIG_SYS_MAXIDLE      10
  38
  39 #define CONFIG_BOOTCOUNT_LIMIT
  40
  41
  42 #define CONFIG_BOARD_TYPES      1       /* support board types          */
  43
  44 #define CONFIG_PREBOOT  "echo;" \
  45         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
  46         "echo"
  47
  48 #undef  CONFIG_BOOTARGS
  49
  50 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  51         "netdev=eth0\0"                                                 \
  52         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
  53                 "nfsroot=${serverip}:${rootpath}\0"                     \
  54         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
  55         "addip=setenv bootargs ${bootargs} "                            \
  56                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  57                 ":${hostname}:${netdev}:off panic=1\0"                  \
  58         "flash_nfs=run nfsargs addip;"                                  \
  59                 "bootm ${kernel_addr}\0"                                \
  60         "flash_self=run ramargs addip;"                                 \
  61                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  62         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
  63         "rootpath=/opt/eldk/ppc_8xx\0"                                  \
  64         "bootfile=/tftpboot/TQM885D/uImage\0"                           \
  65         "fdt_addr=400C0000\0"                                           \
  66         "kernel_addr=40100000\0"                                        \
  67         "ramdisk_addr=40280000\0"                                       \
  68         "load=tftp 200000 ${u-boot}\0"                                  \
  69         "update=protect off 40000000 +${filesize};"                     \
  70                 "erase 40000000 +${filesize};"                          \
  71                 "cp.b 200000 40000000 ${filesize};"                     \
  72                 "protect on 40000000 +${filesize}\0"                    \
  73         ""
  74 #define CONFIG_BOOTCOMMAND      "run flash_self"
  75
  76 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
  77 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
  78
  79 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  80
  81 #undef  CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
  82
  83 /* enable I2C and select the hardware/software driver */
  84 #define CONFIG_SYS_I2C
  85 #define CONFIG_SYS_I2C_SOFT                     /* I2C bit-banged */
  86 #define CONFIG_SYS_I2C_SOFT_SPEED       93000   /* 93 kHz is supposed to work */
  87 #define CONFIG_SYS_I2C_SOFT_SLAVE       0xFE
  88 /*
  89  * Software (bit-bang) I2C driver configuration
  90  */
  91 #define PB_SCL          0x00000020      /* PB 26 */
  92 #define PB_SDA          0x00000010      /* PB 27 */
  93
  94 #define I2C_INIT        (immr->im_cpm.cp_pbdir |=  PB_SCL)
  95 #define I2C_ACTIVE      (immr->im_cpm.cp_pbdir |=  PB_SDA)
  96 #define I2C_TRISTATE    (immr->im_cpm.cp_pbdir &= ~PB_SDA)
  97 #define I2C_READ        ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
  98 #define I2C_SDA(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
  99                         else    immr->im_cpm.cp_pbdat &= ~PB_SDA
 100 #define I2C_SCL(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 101                         else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 102 #define I2C_DELAY       udelay(2)       /* 1/4 I2C clock duration */
 103
 104 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* EEPROM AT24C??       */
 105 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2                /* two byte address     */
 106 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 107 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
 108
 109 # define CONFIG_RTC_DS1337 1
 110 # define CONFIG_SYS_I2C_RTC_ADDR 0x68
 111
 112 /*
 113  * BOOTP options
 114  */
 115 #define CONFIG_BOOTP_SUBNETMASK
 116 #define CONFIG_BOOTP_GATEWAY
 117 #define CONFIG_BOOTP_HOSTNAME
 118 #define CONFIG_BOOTP_BOOTPATH
 119 #define CONFIG_BOOTP_BOOTFILESIZE
 120
 121 #undef CONFIG_RTC_MPC8xx                /* MPC885 does not support RTC  */
 122
 123 #define CONFIG_TIMESTAMP                /* but print image timestmps    */
 124
 125 /*
 126  * Command line configuration.
 127  */
 128 #define CONFIG_CMD_EEPROM
 129 #define CONFIG_CMD_IDE
 130
 131 /*
 132  * Miscellaneous configurable options
 133  */
 134 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 135
 136 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 137
 138 #if defined(CONFIG_CMD_KGDB)
 139 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
 140 #else
 141 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
 142 #endif
 143 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 144 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 145 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 146
 147 #define CONFIG_SYS_MEMTEST_START        0x0100000       /* memtest works on     */
 148 #define CONFIG_SYS_MEMTEST_END          0x0300000       /* 1 ... 3 MB in DRAM   */
 149 #define CONFIG_SYS_ALT_MEMTEST                          /* alternate, more extensive
 150                                                    memory test.*/
 151
 152 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 153
 154 /*
 155  * Low Level Configuration Settings
 156  * (address mappings, register initial values, etc.)
 157  * You should know what you are doing if you make changes here.
 158  */
 159 /*-----------------------------------------------------------------------
 160  * Internal Memory Mapped Register
 161  */
 162 #define CONFIG_SYS_IMMR         0xFFF00000
 163
 164 /*-----------------------------------------------------------------------
 165  * Definitions for initial stack pointer and data area (in DPRAM)
 166  */
 167 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 168 #define CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
 169 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 170 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 171
 172 /*-----------------------------------------------------------------------
 173  * Start addresses for the final memory configuration
 174  * (Set up by the startup code)
 175  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 176  */
 177 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 178 #define CONFIG_SYS_FLASH_BASE           0x40000000
 179 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 180 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 181 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* Reserve 128 kB for malloc()  */
 182
 183 /*
 184  * For booting Linux, the board info and command line data
 185  * have to be in the first 8 MB of memory, since this is
 186  * the maximum mapped by the Linux kernel during initialization.
 187  */
 188 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 189
 190 /*-----------------------------------------------------------------------
 191  * FLASH organization
 192  */
 193
 194 /* use CFI flash driver */
 195 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 196 #define CONFIG_FLASH_CFI_DRIVER 1       /* Use the common driver */
 197 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 198 #define CONFIG_SYS_FLASH_EMPTY_INFO
 199 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 200 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
 201 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */
 202
 203 #define CONFIG_ENV_IS_IN_FLASH  1
 204 #define CONFIG_ENV_OFFSET               0x40000 /*   Offset   of Environment Sector     */
 205 #define CONFIG_ENV_SIZE         0x08000 /* Total Size of Environment            */
 206 #define CONFIG_ENV_SECT_SIZE    0x40000 /* Total Size of Environment Sector     */
 207
 208 /* Address and size of Redundant Environment Sector     */
 209 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 210 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 211
 212 /*-----------------------------------------------------------------------
 213  * Hardware Information Block
 214  */
 215 #define CONFIG_SYS_HWINFO_OFFSET        0x0003FFC0      /* offset of HW Info block */
 216 #define CONFIG_SYS_HWINFO_SIZE          0x00000040      /* size   of HW Info block */
 217 #define CONFIG_SYS_HWINFO_MAGIC 0x54514D38      /* 'TQM8' */
 218
 219 /*-----------------------------------------------------------------------
 220  * Cache Configuration
 221  */
 222 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 223 #if defined(CONFIG_CMD_KGDB)
 224 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 225 #endif
 226
 227 /*-----------------------------------------------------------------------
 228  * SYPCR - System Protection Control                            11-9
 229  * SYPCR can only be written once after reset!
 230  *-----------------------------------------------------------------------
 231  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 232  */
 233 #if defined(CONFIG_WATCHDOG)
 234 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 235                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 236 #else
 237 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 238 #endif
 239
 240 /*-----------------------------------------------------------------------
 241  * SIUMCR - SIU Module Configuration                            11-6
 242  *-----------------------------------------------------------------------
 243  * PCMCIA config., multi-function pin tri-state
 244  */
 245 #ifndef CONFIG_CAN_DRIVER
 246 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 247 #else   /* we must activate GPL5 in the SIUMCR for CAN */
 248 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 249 #endif  /* CONFIG_CAN_DRIVER */
 250
 251 /*-----------------------------------------------------------------------
 252  * TBSCR - Time Base Status and Control                         11-26
 253  *-----------------------------------------------------------------------
 254  * Clear Reference Interrupt Status, Timebase freezing enabled
 255  */
 256 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 257
 258 /*-----------------------------------------------------------------------
 259  * PISCR - Periodic Interrupt Status and Control                11-31
 260  *-----------------------------------------------------------------------
 261  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 262  */
 263 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF)
 264
 265 /*-----------------------------------------------------------------------
 266  * SCCR - System Clock and reset Control Register               15-27
 267  *-----------------------------------------------------------------------
 268  * Set clock output, timebase and RTC source and divider,
 269  * power management and some other internal clocks
 270  */
 271 #define SCCR_MASK       SCCR_EBDF11
 272 #define CONFIG_SYS_SCCR (SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 273                          SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 274                          SCCR_DFALCD00)
 275
 276 /*-----------------------------------------------------------------------
 277  * PCMCIA stuff
 278  *-----------------------------------------------------------------------
 279  *
 280  */
 281 #define CONFIG_SYS_PCMCIA_MEM_ADDR      (0xE0000000)
 282 #define CONFIG_SYS_PCMCIA_MEM_SIZE      ( 64 << 20 )
 283 #define CONFIG_SYS_PCMCIA_DMA_ADDR      (0xE4000000)
 284 #define CONFIG_SYS_PCMCIA_DMA_SIZE      ( 64 << 20 )
 285 #define CONFIG_SYS_PCMCIA_ATTRB_ADDR    (0xE8000000)
 286 #define CONFIG_SYS_PCMCIA_ATTRB_SIZE    ( 64 << 20 )
 287 #define CONFIG_SYS_PCMCIA_IO_ADDR       (0xEC000000)
 288 #define CONFIG_SYS_PCMCIA_IO_SIZE       ( 64 << 20 )
 289
 290 /*-----------------------------------------------------------------------
 291  * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 292  *-----------------------------------------------------------------------
 293  */
 294
 295 #define CONFIG_IDE_PREINIT      1       /* Use preinit IDE hook */
 296 #define CONFIG_IDE_8xx_PCCARD   1       /* Use IDE with PC Card Adapter */
 297
 298 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 299 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 300 #undef  CONFIG_IDE_RESET                /* reset for ide not supported  */
 301
 302 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 303 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 1 drive per IDE bus     */
 304
 305 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 306
 307 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_PCMCIA_MEM_ADDR
 308
 309 /* Offset for data I/O                  */
 310 #define CONFIG_SYS_ATA_DATA_OFFSET      (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 311
 312 /* Offset for normal register accesses  */
 313 #define CONFIG_SYS_ATA_REG_OFFSET       (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 314
 315 /* Offset for alternate registers       */
 316 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0100
 317
 318 /*-----------------------------------------------------------------------
 319  *
 320  *-----------------------------------------------------------------------
 321  *
 322  */
 323 #define CONFIG_SYS_DER 0
 324
 325 /*
 326  * Init Memory Controller:
 327  *
 328  * BR0/1 and OR0/1 (FLASH)
 329  */
 330
 331 #define FLASH_BASE0_PRELIM      0x40000000      /* FLASH bank #0        */
 332 #define FLASH_BASE1_PRELIM      0x60000000      /* FLASH bank #0        */
 333
 334 /* used to re-map FLASH both when starting from SRAM or FLASH:
 335  * restrict access enough to keep SRAM working (if any)
 336  * but not too much to meddle with FLASH accesses
 337  */
 338 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 339 #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000      /* OR addr mask */
 340
 341 /*
 342  * FLASH timing: Default value of OR0 after reset
 343  */
 344 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
 345                                  OR_SCY_6_CLK | OR_TRLX)
 346
 347 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 348 #define CONFIG_SYS_OR0_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 349 #define CONFIG_SYS_BR0_PRELIM   ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
 350
 351 #define CONFIG_SYS_OR1_REMAP    CONFIG_SYS_OR0_REMAP
 352 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 353 #define CONFIG_SYS_BR1_PRELIM   ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
 354
 355 /*
 356  * BR2/3 and OR2/3 (SDRAM)
 357  *
 358  */
 359 #define SDRAM_BASE2_PRELIM      0x00000000      /* SDRAM bank #0        */
 360 #define SDRAM_BASE3_PRELIM      0x20000000      /* SDRAM bank #1        */
 361 #define SDRAM_MAX_SIZE          (256 << 20)     /* max 256 MB per bank  */
 362
 363 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)      */
 364 #define CONFIG_SYS_OR_TIMING_SDRAM      0x00000A00
 365
 366 #define CONFIG_SYS_OR2_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
 367 #define CONFIG_SYS_BR2_PRELIM   ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 368
 369 #ifndef CONFIG_CAN_DRIVER
 370 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 371 #define CONFIG_SYS_BR3_PRELIM   ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 372 #else   /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
 373 #define CONFIG_SYS_CAN_BASE             0xC0000000      /* CAN mapped at 0xC0000000     */
 374 #define CONFIG_SYS_CAN_OR_AM            0xFFFF8000      /* 32 kB address mask           */
 375 #define CONFIG_SYS_OR3_CAN              (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
 376 #define CONFIG_SYS_BR3_CAN              ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
 377                                         BR_PS_8 | BR_MS_UPMB | BR_V )
 378 #endif  /* CONFIG_CAN_DRIVER */
 379
 380 /*
 381  * 4096 Rows from SDRAM example configuration
 382  * 1000 factor s -> ms
 383  * 64   PTP (pre-divider from MPTPR) from SDRAM example configuration
 384  * 4    Number of refresh cycles per period
 385  * 64   Refresh cycle in ms per number of rows
 386  */
 387 #define CONFIG_SYS_PTA_PER_CLK  ((4096 * 64 * 1000) / (4 * 64))
 388
 389 /*
 390  * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
 391  *
 392  *                        CPUclock(MHz) * 31.2
 393  * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
 394  *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
 395  *
 396  * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
 397  * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
 398  * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
 399  * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
 400  *
 401  * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
 402  * be met also in the default configuration, i.e. if environment variable
 403  * 'cpuclk' is not set.
 404  */
 405 #define CONFIG_SYS_MAMR_PTA             128
 406
 407 /*
 408  * Memory Periodic Timer Prescaler Register (MPTPR) values.
 409  */
 410 /* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
 411 #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16
 412 /* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
 413 #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8
 414
 415 /*
 416  * MAMR settings for SDRAM
 417  */
 418
 419 /* 8 column SDRAM */
 420 #define CONFIG_SYS_MAMR_8COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 421                          MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
 422                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 423 /* 9 column SDRAM */
 424 #define CONFIG_SYS_MAMR_9COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 425                          MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
 426                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 427 /* 10 column SDRAM */
 428 #define CONFIG_SYS_MAMR_10COL   ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 429                          MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |   \
 430                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 431
 432 /*
 433  * Network configuration
 434  */
 435 #define CONFIG_SCC2_ENET                /* enable ethernet on SCC2 */
 436 #define CONFIG_FEC_ENET                 /* enable ethernet on FEC */
 437 #define CONFIG_ETHER_ON_FEC1            /* ... for FEC1 */
 438 #define CONFIG_ETHER_ON_FEC2            /* ... for FEC2 */
 439
 440 #if defined(CONFIG_CMD_MII)
 441 #define CONFIG_SYS_DISCOVER_PHY
 442 #define CONFIG_MII_INIT 1
 443 #endif
 444
 445 #define CONFIG_NET_RETRY_COUNT 1        /* reduce max. timeout before
 446                                            switching to another netwok (if the
 447                                            tried network is unreachable) */
 448
 449 #define CONFIG_ETHPRIME         "SCC"
 450
 451 #define CONFIG_HWCONFIG         1
 452
 453 #endif  /* __CONFIG_H */