include/configs/Total5200.h

   1 /*
   2  * (C) Copyright 2003-2004
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * (C) Copyright 2004
   6  * Mark Jonas, Freescale Semiconductor, mark.jonas@freescale.com.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * Check valid setting of revision define.
  16  * Total5100 and Total5200 Rev.1 are identical except for the processor.
  17  */
  18 #if (CONFIG_TOTAL5200_REV!=1 && CONFIG_TOTAL5200_REV!=2)
  19 #error CONFIG_TOTAL5200_REV must be 1 or 2
  20 #endif
  21
  22 /*
  23  * High Level Configuration Options
  24  * (easy to change)
  25  */
  26
  27 #define CONFIG_MPC5200          1       /* This is a MPC5200 CPU */
  28 #define CONFIG_TOTAL5200        1       /* ... on Total5200 board */
  29
  30 /*
  31  * Valid values for CONFIG_SYS_TEXT_BASE are:
  32  * 0xFFF00000   boot high (standard configuration)
  33  * 0xFE000000   boot low
  34  * 0x00100000   boot from RAM (for testing only)
  35  */
  36 #ifndef CONFIG_SYS_TEXT_BASE
  37 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  38 #endif
  39
  40 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000 /* ... running at 33.000000MHz */
  41
  42 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  43
  44 /*
  45  * Serial console configuration
  46  */
  47 #define CONFIG_PSC_CONSOLE      3       /* console is on PSC3 */
  48 #define CONFIG_BAUDRATE         115200  /* ... at 115200 bps */
  49 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  50
  51 /*
  52  * Video console
  53  */
  54 #define CONFIG_VIDEO
  55 #define CONFIG_VIDEO_SED13806
  56 #define CONFIG_VIDEO_SED13806_16BPP
  57
  58 #define CONFIG_CFB_CONSOLE
  59 #define CONFIG_VIDEO_LOGO
  60 /* #define CONFIG_VIDEO_BMP_LOGO */
  61 #define CONFIG_CONSOLE_EXTRA_INFO
  62 #define CONFIG_VGA_AS_SINGLE_DEVICE
  63 #define CONFIG_VIDEO_SW_CURSOR
  64 #define CONFIG_SPLASH_SCREEN
  65
  66
  67 /*
  68  * PCI Mapping:
  69  * 0x40000000 - 0x4fffffff - PCI Memory
  70  * 0x50000000 - 0x50ffffff - PCI IO Space
  71  */
  72 #define CONFIG_PCI              1
  73 #define CONFIG_PCI_PNP          1
  74 #define CONFIG_PCI_SCAN_SHOW    1
  75 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
  76
  77 #define CONFIG_PCI_MEM_BUS      0x40000000
  78 #define CONFIG_PCI_MEM_PHYS     CONFIG_PCI_MEM_BUS
  79 #define CONFIG_PCI_MEM_SIZE     0x10000000
  80
  81 #define CONFIG_PCI_IO_BUS       0x50000000
  82 #define CONFIG_PCI_IO_PHYS      CONFIG_PCI_IO_BUS
  83 #define CONFIG_PCI_IO_SIZE      0x01000000
  84
  85 #define CONFIG_MII              1
  86 #define CONFIG_EEPRO100         1
  87 #define CONFIG_SYS_RX_ETH_BUFFER        8  /* use 8 rx buffer on eepro100  */
  88 #define CONFIG_NS8382X          1
  89
  90 /* Partitions */
  91 #define CONFIG_MAC_PARTITION
  92 #define CONFIG_DOS_PARTITION
  93
  94 /* USB */
  95 #define CONFIG_USB_OHCI
  96 #define CONFIG_USB_STORAGE
  97
  98
  99 /*
 100  * BOOTP options
 101  */
 102 #define CONFIG_BOOTP_BOOTFILESIZE
 103 #define CONFIG_BOOTP_BOOTPATH
 104 #define CONFIG_BOOTP_GATEWAY
 105 #define CONFIG_BOOTP_HOSTNAME
 106
 107
 108 /*
 109  * Command line configuration.
 110  */
 111 #include <config_cmd_default.h>
 112
 113 #define CONFIG_CMD_PCI
 114
 115 #define CONFIG_CMD_BMP
 116 #define CONFIG_CMD_EEPROM
 117 #define CONFIG_CMD_FAT
 118 #define CONFIG_CMD_I2C
 119 #define CONFIG_CMD_IDE
 120 #define CONFIG_CMD_PING
 121 #define CONFIG_CMD_USB
 122
 123
 124 #if (CONFIG_SYS_TEXT_BASE == 0xFE000000)                /* Boot low */
 125 #   define CONFIG_SYS_LOWBOOT           1
 126 #endif
 127
 128 /*
 129  * Autobooting
 130  */
 131 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
 132
 133 #define CONFIG_PREBOOT  \
 134         "setenv stdout serial;setenv stderr serial;" \
 135         "echo;" \
 136         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 137         "echo"
 138
 139 #undef  CONFIG_BOOTARGS
 140
 141 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 142         "netdev=eth0\0"                                                 \
 143         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 144                 "nfsroot=${serverip}:${rootpath}\0"                     \
 145         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 146         "addip=setenv bootargs ${bootargs} "                            \
 147                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 148                 ":${hostname}:${netdev}:off panic=1\0"                  \
 149         "flash_nfs=run nfsargs addip;"                                  \
 150                 "bootm ${kernel_addr}\0"                                \
 151         "flash_self=run ramargs addip;"                                 \
 152                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 153         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
 154         "rootpath=/opt/eldk/ppc_82xx\0"                                 \
 155         "bootfile=/tftpboot/MPC5200/uImage\0"                           \
 156         ""
 157
 158 #define CONFIG_BOOTCOMMAND      "run flash_self"
 159
 160 /*
 161  * IPB Bus clocking configuration.
 162  */
 163 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK          /* define for 133MHz speed */
 164
 165 /*
 166  * I2C configuration
 167  */
 168 #define CONFIG_HARD_I2C         1       /* I2C with hardware support */
 169 #define CONFIG_SYS_I2C_MODULE           1       /* Select I2C module #1 or #2 */
 170
 171 #define CONFIG_SYS_I2C_SPEED            100000 /* 100 kHz */
 172 #define CONFIG_SYS_I2C_SLAVE            0x7F
 173
 174 /*
 175  * EEPROM configuration
 176  */
 177 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50    /* 1010000x */
 178 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 179 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 180 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   70
 181
 182 /*
 183  * Flash configuration
 184  */
 185 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 186 #define CONFIG_FLASH_CFI_DRIVER 1       /* Use the common driver */
 187 #if CONFIG_TOTAL5200_REV==2
 188 #   define CONFIG_SYS_MAX_FLASH_BANKS   3       /* max num of flash banks */
 189 #   define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START }
 190 #else
 191 #   define CONFIG_SYS_MAX_FLASH_BANKS   1       /* max num of flash banks  */
 192 #   define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START }
 193 #endif
 194 #define CONFIG_SYS_FLASH_EMPTY_INFO
 195 #define CONFIG_SYS_MAX_FLASH_SECT       128     /* max num of sects on one chip */
 196
 197 #if CONFIG_TOTAL5200_REV==1
 198 #   define CONFIG_SYS_FLASH_BASE        0xFE000000
 199 #   define CONFIG_SYS_FLASH_SIZE        0x02000000
 200 #elif CONFIG_TOTAL5200_REV==2
 201 #   define CONFIG_SYS_FLASH_BASE        0xFA000000
 202 #   define CONFIG_SYS_FLASH_SIZE        0x06000000
 203 #endif /* CONFIG_TOTAL5200_REV */
 204
 205 #if defined(CONFIG_SYS_LOWBOOT)
 206 #   define CONFIG_ENV_ADDR              0xFE040000
 207 #else   /* CONFIG_SYS_LOWBOOT */
 208 #   define CONFIG_ENV_ADDR              0xFFF40000
 209 #endif  /* CONFIG_SYS_LOWBOOT */
 210
 211 /*
 212  * Environment settings
 213  */
 214 #define CONFIG_ENV_IS_IN_FLASH  1
 215 #define CONFIG_ENV_SIZE         0x40000
 216 #define CONFIG_ENV_SECT_SIZE    0x40000
 217 #define CONFIG_ENV_OVERWRITE    1
 218
 219 /*
 220  * Memory map
 221  */
 222 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 223 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 224 #define CONFIG_SYS_MBAR         0xF0000000      /*   64 kB */
 225 #define CONFIG_SYS_FPGA_BASE            0xF0010000      /*   64 kB */
 226 #define CONFIG_SYS_CPLD_BASE            0xF0020000      /*   64 kB */
 227 #define CONFIG_SYS_LCD_BASE             0xF1000000      /* 4096 kB */
 228
 229 /* Use SRAM until RAM will be available */
 230 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 231 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 232
 233 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 234 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 235
 236 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 237 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 238 #   define CONFIG_SYS_RAMBOOT           1
 239 #endif
 240
 241 #define CONFIG_SYS_MONITOR_LEN          (192 << 10)     /* Reserve 192 kB for Monitor   */
 242 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 243 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 244
 245 /*
 246  * Ethernet configuration
 247  */
 248 #define CONFIG_MPC5xxx_FEC      1
 249 #define CONFIG_MPC5xxx_FEC_SEVENWIRE
 250 /* dummy, 7-wire FEC does not have phy address */
 251 #define CONFIG_PHY_ADDR         0x00
 252
 253 /*
 254  * GPIO configuration
 255  *
 256  * CS1:   SDRAM CS1 disabled, gpio_wkup_6 enabled                0
 257  * Reserved                                                      0
 258  * ALTs:  CAN1/2 on PSC2, SPI on PSC3                            00
 259  * CS7:   Interrupt GPIO on PSC3_5                               0
 260  * CS8:   Interrupt GPIO on PSC3_4                               0
 261  * ATA:   reset default, changed in ATA driver                   00
 262  * IR_USB_CLK: IrDA/USB 48MHz clock gen. int., pin is GPIO       0
 263  * IRDA:  reset default, changed in IrDA driver                  000
 264  * ETHER: reset default, changed in Ethernet driver              0000
 265  * PCI_DIS: reset default, changed in PCI driver                 0
 266  * USB_SE: reset default, changed in USB driver                  0
 267  * USB:   reset default, changed in USB driver                   00
 268  * PSC3:  SPI and UART functionality without CD                  1100
 269  * Reserved                                                      0
 270  * PSC2:  CAN1/2                                                 001
 271  * Reserved                                                      0
 272  * PSC1:  reset default, changed in AC'97 driver                 000
 273  *
 274  */
 275 #define CONFIG_SYS_GPS_PORT_CONFIG      0x00000C10
 276
 277 /*
 278  * Miscellaneous configurable options
 279  */
 280 #define CONFIG_SYS_LONGHELP                     /* undef to save memory     */
 281 #if defined(CONFIG_CMD_KGDB)
 282 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 283 #else
 284 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 285 #endif
 286 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 287 #define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
 288 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 289
 290 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 291 #define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 292
 293 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 294
 295 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 296 #if defined(CONFIG_CMD_KGDB)
 297 #  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
 298 #endif
 299
 300
 301 /*
 302  * Various low-level settings
 303  */
 304 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 305 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 306
 307 #if CONFIG_TOTAL5200_REV==1
 308 #   define CONFIG_SYS_BOOTCS_START      CONFIG_SYS_FLASH_BASE
 309 #   define CONFIG_SYS_BOOTCS_SIZE       0x02000000      /* 32 MB */
 310 #   define CONFIG_SYS_BOOTCS_CFG        0x0004DF00      /* 4WS, MX, AL, CE, AS_25, DS_32 */
 311 #   define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
 312 #   define CONFIG_SYS_CS0_SIZE          0x02000000      /* 32 MB */
 313 #else
 314 #   define CONFIG_SYS_BOOTCS_START      (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE)
 315 #   define CONFIG_SYS_BOOTCS_SIZE       0x02000000      /* 32 MB */
 316 #   define CONFIG_SYS_BOOTCS_CFG        0x0004DF00      /* 4WS, MX, AL, CE, AS_25, DS_32 */
 317 #   define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE)
 318 #   define CONFIG_SYS_CS4_SIZE          0x02000000      /* 32 MB */
 319 #   define CONFIG_SYS_CS4_CFG           0x0004DF00      /* 4WS, MX, AL, CE, AS_25, DS_32 */
 320 #   define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE
 321 #   define CONFIG_SYS_CS5_SIZE          0x02000000      /* 32 MB */
 322 #   define CONFIG_SYS_CS5_CFG           0x0004DF00      /* 4WS, MX, AL, CE, AS_25, DS_32 */
 323 #endif
 324
 325 #define CONFIG_SYS_CS1_START            CONFIG_SYS_FPGA_BASE
 326 #define CONFIG_SYS_CS1_SIZE             0x00010000      /* 64 kB */
 327 #define CONFIG_SYS_CS1_CFG              0x0019FF00      /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */
 328
 329 #define CONFIG_SYS_CS2_START            CONFIG_SYS_LCD_BASE
 330 #define CONFIG_SYS_CS2_SIZE             0x00400000      /* 4096 kB */
 331 #define CONFIG_SYS_CS2_CFG              0x0032FD0C      /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */
 332
 333 #if CONFIG_TOTAL5200_REV==1
 334 #   define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE
 335 #   define CONFIG_SYS_CS3_SIZE          0x00010000      /* 64 kB */
 336 #   define CONFIG_SYS_CS3_CFG           0x000ADF00      /* 10WS, MX, AL, CE, AS_25, DS_32 */
 337 #else
 338 #   define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE
 339 #   define CONFIG_SYS_CS3_SIZE          0x00010000      /* 64 kB */
 340 #   define CONFIG_SYS_CS3_CFG           0x000AD800      /* 10WS, MX, AL, CE, AS_24, DS_8 */
 341 #endif
 342
 343 #define CONFIG_SYS_CS_BURST             0x00000000
 344 #define CONFIG_SYS_CS_DEADCYCLE 0x33333333
 345
 346 /*-----------------------------------------------------------------------
 347  * USB stuff
 348  *-----------------------------------------------------------------------
 349  */
 350 #define CONFIG_USB_CLOCK        0x0001BBBB
 351 #define CONFIG_USB_CONFIG       0x00001000
 352
 353 /*-----------------------------------------------------------------------
 354  * IDE/ATA stuff Supports IDE harddisk
 355  *-----------------------------------------------------------------------
 356  */
 357
 358 #undef  CONFIG_IDE_8xx_PCCARD           /* Use IDE with PC Card Adapter */
 359
 360 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 361 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 362
 363 #define CONFIG_IDE_RESET                /* reset for ide supported      */
 364 #define CONFIG_IDE_PREINIT
 365
 366 #define CONFIG_SYS_ATA_CS_ON_I2C2
 367 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 368 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 1 drive per IDE bus     */
 369
 370 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 371
 372 #define CONFIG_SYS_ATA_BASE_ADDR        MPC5XXX_ATA
 373
 374 /* Offset for data I/O                  */
 375 #define CONFIG_SYS_ATA_DATA_OFFSET      (0x0060)
 376
 377 /* Offset for normal register accesses  */
 378 #define CONFIG_SYS_ATA_REG_OFFSET       (CONFIG_SYS_ATA_DATA_OFFSET)
 379
 380 /* Offset for alternate registers       */
 381 #define CONFIG_SYS_ATA_ALT_OFFSET       (0x005C)
 382
 383 /* Interval between registers                                                */
 384 #define CONFIG_SYS_ATA_STRIDE          4
 385
 386 #endif /* __CONFIG_H */