Merge branch 'master' of git://www.denx.de/git/u-boot-imx

[people/ms/u-boot.git] / include / configs / UCP1020.h

/*
 * Copyright 2013-2015 Arcturus Networks, Inc.
 *           http://www.arcturusnetworks.com/products/ucp1020/
 * based on include/configs/p1_p2_rdb_pc.h
 * original copyright follows:
 * Copyright 2009-2011 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

/*
 * QorIQ uCP1020-xx boards configuration file
 */
#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO

#define CONFIG_FSL_ELBC
#define CONFIG_PCI
#define CONFIG_PCIE1    /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2    /* PCIE controller 2 (slot 2) */
#define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
#define CONFIG_FSL_PCIE_RESET   /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */

#if defined(CONFIG_TARTGET_UCP1020T1)

#define CONFIG_UCP1020_REV_1_3

#define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1"
#define CONFIG_P1020

#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#define CONFIG_TSEC3
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_ETHADDR          00:19:D3:FF:FF:FF
#define CONFIG_ETH1ADDR         00:19:D3:FF:FF:FE
#define CONFIG_ETH2ADDR         00:19:D3:FF:FF:FD
#define CONFIG_IPADDR           10.80.41.229
#define CONFIG_SERVERIP         10.80.41.227
#define CONFIG_NETMASK          255.255.252.0
#define CONFIG_ETHPRIME         "eTSEC3"

#ifndef CONFIG_SPI_FLASH
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT

#define CONFIG_MMC
#define CONFIG_SYS_L2_SIZE      (256 << 10)

#define CONFIG_LAST_STAGE_INIT

#if !defined(CONFIG_DONGLE)
#define CONFIG_SILENT_CONSOLE
#endif

#endif

#if defined(CONFIG_TARGET_UCP1020)

#define CONFIG_UCP1020
#define CONFIG_UCP1020_REV_1_3

#define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR"
#define CONFIG_P1020

#define CONFIG_TSEC_ENET
#define CONFIG_TSEC1
#define CONFIG_TSEC2
#define CONFIG_TSEC3
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_ETHADDR          00:06:3B:FF:FF:FF
#define CONFIG_ETH1ADDR         00:06:3B:FF:FF:FE
#define CONFIG_ETH2ADDR         00:06:3B:FF:FF:FD
#define CONFIG_IPADDR           192.168.1.81
#define CONFIG_IPADDR1          192.168.1.82
#define CONFIG_IPADDR2          192.168.1.83
#define CONFIG_SERVERIP         192.168.1.80
#define CONFIG_GATEWAYIP        102.168.1.1
#define CONFIG_NETMASK          255.255.255.0
#define CONFIG_ETHPRIME         "eTSEC1"

#ifndef CONFIG_SPI_FLASH
#endif
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT

#define CONFIG_MMC
#define CONFIG_SYS_L2_SIZE      (256 << 10)

#define CONFIG_LAST_STAGE_INIT

#endif

#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE            0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
#endif

#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_SYS_TEXT_BASE            0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS     0x1107fffc
#endif

#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE            0xeff80000
#endif
#define CONFIG_SYS_TEXT_BASE_NOR        0xeff80000

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
#endif

#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
#endif

/* High Level Configuration Options */
#define CONFIG_BOOKE
#define CONFIG_E500
/* #define CONFIG_MPC85xx */

#define CONFIG_MP

#define CONFIG_FSL_LAW

#define CONFIG_ENV_OVERWRITE

#define CONFIG_CMD_SATA
#define CONFIG_SATA_SIL
#define CONFIG_SYS_SATA_MAX_DEVICE      2
#define CONFIG_LIBATA
#define CONFIG_LBA48

#define CONFIG_SYS_CLK_FREQ     66666666
#define CONFIG_DDR_CLK_FREQ     66666666

#define CONFIG_HWCONFIG

#define CONFIG_DTT_ADM1021      1       /* ADM1021 temp sensor support  */
#define CONFIG_SYS_DTT_BUS_NUM  1       /* The I2C bus for DTT          */
#define CONFIG_DTT_SENSORS      { 0, 1 }        /* Sensor index */
/*
 * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details).
 * there will be one entry in this array for each two (dummy) sensors in
 * CONFIG_DTT_SENSORS.
 *
 * For uCP1020 module:
 * - only one ADM1021/NCT72
 * - i2c addr 0x41
 * - conversion rate 0x02 = 0.25 conversions/second
 * - ALERT output disabled
 * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
 * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
 */
#define CONFIG_SYS_DTT_ADM1021  { { CONFIG_SYS_I2C_NCT72_ADDR, \
                                         0x02, 0, 1, 0, 85, 1, 0, 85} }

#define CONFIG_CMD_DTT

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE
#define CONFIG_BTB

#define CONFIG_BOARD_EARLY_INIT_F       /* Call board_pre_init */

#define CONFIG_ENABLE_36BIT_PHYS

#define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
#define CONFIG_SYS_MEMTEST_END          0x1fffffff
#define CONFIG_PANIC_HANG       /* do not reset board on panic */

#define CONFIG_SYS_CCSRBAR              0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR

/* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k
       SPL code*/
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif

/* DDR Setup */
#define CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_FSL_DDR3
#ifndef CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_DDR_RAW_TIMING
#define CONFIG_DDR_SPD
#endif
#define CONFIG_SYS_SPD_BUS_NUM 1
#undef CONFIG_FSL_DDR_INTERACTIVE

#define CONFIG_SYS_SDRAM_SIZE_LAW       LAW_SIZE_512M
#define CONFIG_CHIP_SELECTS_PER_CTRL    1
#define CONFIG_SYS_SDRAM_SIZE           (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_NUM_DDR_CONTROLLERS      1
#define CONFIG_DIMM_SLOTS_PER_CTLR      1

/* Default settings for DDR3 */
#define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f
#define CONFIG_SYS_DDR_CS0_CONFIG       0x80014302
#define CONFIG_SYS_DDR_CS0_CONFIG_2     0x00000000
#define CONFIG_SYS_DDR_CS1_BNDS         0x0040007f
#define CONFIG_SYS_DDR_CS1_CONFIG       0x80014302
#define CONFIG_SYS_DDR_CS1_CONFIG_2     0x00000000

#define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
#define CONFIG_SYS_DDR_INIT_ADDR        0x00000000
#define CONFIG_SYS_DDR_INIT_EXT_ADDR    0x00000000
#define CONFIG_SYS_DDR_MODE_CONTROL     0x00000000

#define CONFIG_SYS_DDR_ZQ_CONTROL       0x89080600
#define CONFIG_SYS_DDR_WRLVL_CONTROL    0x8655A608
#define CONFIG_SYS_DDR_SR_CNTR          0x00000000
#define CONFIG_SYS_DDR_RCW_1            0x00000000
#define CONFIG_SYS_DDR_RCW_2            0x00000000
#ifdef CONFIG_DDR_ECC_ENABLE
#define CONFIG_SYS_DDR_CONTROL          0xE70C0000      /* Type = DDR3 & ECC */
#else
#define CONFIG_SYS_DDR_CONTROL          0xC70C0000      /* Type = DDR3 */
#endif
#define CONFIG_SYS_DDR_CONTROL_2        0x04401050
#define CONFIG_SYS_DDR_TIMING_4         0x00220001
#define CONFIG_SYS_DDR_TIMING_5         0x03402400

#define CONFIG_SYS_DDR_TIMING_3         0x00020000
#define CONFIG_SYS_DDR_TIMING_0         0x00330004
#define CONFIG_SYS_DDR_TIMING_1         0x6f6B4846
#define CONFIG_SYS_DDR_TIMING_2         0x0FA8C8CF
#define CONFIG_SYS_DDR_CLK_CTRL         0x03000000
#define CONFIG_SYS_DDR_MODE_1           0x40461520
#define CONFIG_SYS_DDR_MODE_2           0x8000c000
#define CONFIG_SYS_DDR_INTERVAL         0x0C300000

#undef CONFIG_CLOCKS_IN_MHZ

/*
 * Memory map
 *
 * 0x0000_0000 0x7fff_ffff      DDR             Up to 2GB cacheable
 * 0x8000_0000 0xdfff_ffff      PCI Express Mem 1G non-cacheable(PCIe * 2)
 * 0xec00_0000 0xefff_ffff      NOR flash       Up to 64M non-cacheable CS0/1
 * 0xf8f8_0000 0xf8ff_ffff      L2 SRAM         Up to 256K cacheable
 *   (early boot only)
 * 0xffc0_0000 0xffc3_ffff      PCI IO range    256k non-cacheable
 * 0xffd0_0000 0xffd0_3fff      L1 for stack    16K cacheable
 * 0xffe0_0000 0xffef_ffff      CCSR            1M non-cacheable
 */

/*
 * Local Bus Definitions
 */
#define CONFIG_SYS_MAX_FLASH_SECT       512     /* 64M */
#define CONFIG_SYS_FLASH_BASE           0xec000000

#define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE

#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
        | BR_PS_16 | BR_V)

#define CONFIG_FLASH_OR_PRELIM          0xfc000ff7

#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */

#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */

#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

#define CONFIG_BOARD_EARLY_INIT_R       /* call board_early_init_r function */

#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* stack in RAM */
/* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS   CONFIG_SYS_INIT_RAM_ADDR
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
/* Size of used area in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE        0x00004000

#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
                                        GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN  (256 * 1024)/* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)/* Reserved for malloc */

#define CONFIG_SYS_PMC_BASE     0xff980000
#define CONFIG_SYS_PMC_BASE_PHYS        CONFIG_SYS_PMC_BASE
#define CONFIG_PMC_BR_PRELIM    (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \
                                        BR_PS_8 | BR_V)
#define CONFIG_PMC_OR_PRELIM    (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
                                 OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \
                                 OR_GPCM_EAD)

#define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
#ifdef CONFIG_NAND_FSL_ELBC
#define CONFIG_SYS_BR1_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */
#define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
#endif

/* Serial Port - controlled on board with jumper J8
 * open - index 2
 * shorted - index 1
 */
#define CONFIG_CONS_INDEX               1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif

#define CONFIG_SYS_BAUDRATE_TABLE       \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)

/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER

/*
 * Pass open firmware flat tree
 */
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_OF_STDOUT_VIA_ALIAS

/* new uImage format support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED       400000
#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
#define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }
#define CONFIG_SYS_SPD_BUS_NUM          1 /* For rom_loc and flash bank */

#define CONFIG_RTC_DS1337
#define CONFIG_SYS_RTC_DS1337_NOOSC
#define CONFIG_SYS_I2C_RTC_ADDR         0x68
#define CONFIG_SYS_I2C_PCA9557_ADDR     0x18
#define CONFIG_SYS_I2C_NCT72_ADDR       0x4C
#define CONFIG_SYS_I2C_IDT6V49205B      0x69

/*
 * eSPI - Enhanced SPI
 */
#define CONFIG_HARD_SPI
#define CONFIG_FSL_ESPI

#define CONFIG_SPI_FLASH_SST            1
#define CONFIG_SPI_FLASH_STMICRO        1
#define CONFIG_SPI_FLASH_WINBOND        1
#define CONFIG_CMD_SF                   1
#define CONFIG_CMD_SPI                  1
#define CONFIG_SF_DEFAULT_SPEED         10000000
#define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0

#if defined(CONFIG_PCI)
/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

/* controller 2, direct to uli, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_NAME           "PCIe SLOT CON9"
#define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
#define CONFIG_SYS_PCIE2_MEM_BUS        0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       0xa0000000
#define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
#define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS        0xffc10000
#define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */

/* controller 1, Slot 2, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_NAME           "PCIe SLOT CON10"
#define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
#define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT        0xffc00000
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS        0xffc00000
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */

#define CONFIG_PCI_PNP  /* do pci plug-and-play */
#define CONFIG_E1000    /* Defind e1000 pci Ethernet card*/
#define CONFIG_CMD_PCI

#define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#endif /* CONFIG_PCI */

/*
 * Environment
 */
#ifdef CONFIG_ENV_FIT_UCBOOT

#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x20000)
#define CONFIG_ENV_SIZE         0x20000
#define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */

#else

#define CONFIG_ENV_SPI_BUS      0
#define CONFIG_ENV_SPI_CS       0
#define CONFIG_ENV_SPI_MAX_HZ   10000000
#define CONFIG_ENV_SPI_MODE     0

#ifdef CONFIG_RAMBOOT_SPIFLASH

#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE         0x3000          /* 12KB */
#define CONFIG_ENV_OFFSET       0x2000          /* 8KB */
#define CONFIG_ENV_SECT_SIZE    0x1000

#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
/* Address and size of Redundant Environment Sector     */
#define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
#endif

#elif defined(CONFIG_RAMBOOT_SDCARD)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_ENV_SIZE         0x2000
#define CONFIG_SYS_MMC_ENV_DEV  0

#elif defined(CONFIG_SYS_RAMBOOT)
#define CONFIG_ENV_IS_NOWHERE   /* Store ENV in memory only */
#define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE         0x2000

#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_BASE         (CONFIG_SYS_FLASH_BASE)
#define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
#define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
#define CONFIG_ENV_ADDR         (CONFIG_ENV_BASE + 0xC0000)
#if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT)
/* Address and size of Redundant Environment Sector     */
#define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
#endif

#endif

#endif  /* CONFIG_ENV_FIT_UCBOOT */

#define CONFIG_LOADS_ECHO               /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */

/*
 * Command line configuration.
 */
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_ERRATA
#define CONFIG_CMD_CRAMFS
#define CONFIG_CRAMFS_CMDLINE

/*
 * USB
 */
#define CONFIG_HAS_FSL_DR_USB

#if defined(CONFIG_HAS_FSL_DR_USB)
#define CONFIG_USB_EHCI

#define CONFIG_USB_MAX_CONTROLLER_COUNT 1

#ifdef CONFIG_USB_EHCI
#define CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_STORAGE
#endif
#endif

#undef CONFIG_WATCHDOG                  /* watchdog disabled */

#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_CMD_MMC
#define CONFIG_MMC_SPI
#define CONFIG_CMD_MMC_SPI
#define CONFIG_GENERIC_MMC
#endif

#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) || defined(CONFIG_FSL_SATA)
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif

/* Misc Extra Settings */
#define CONFIG_CMD_GPIO                 1
#undef CONFIG_WATCHDOG  /* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory */
#define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
#define CONFIG_SYS_PROMPT       "B$ "           /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
        /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS      16      /* max number of command args */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
#define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms tick */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial Memory for Linux*/
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
#endif

/*
 * Environment Configuration
 */

#if defined(CONFIG_TSEC_ENET)

#if defined(CONFIG_UCP1020_REV_1_2)
#define CONFIG_PHY_MICREL_KSZ9021
#elif defined(CONFIG_UCP1020_REV_1_3)
#define CONFIG_PHY_MICREL_KSZ9031
#else
#error "UCP1020 module revision is not defined !!!"
#endif

#define CONFIG_CMD_DHCP
#define CONFIG_BOOTP_SERVERIP

#define CONFIG_MII              /* MII PHY management */
#define CONFIG_TSEC1_NAME       "eTSEC1"
#define CONFIG_TSEC2_NAME       "eTSEC2"
#define CONFIG_TSEC3_NAME       "eTSEC3"

#define TSEC1_PHY_ADDR  4
#define TSEC2_PHY_ADDR  0
#define TSEC2_PHY_ADDR_SGMII    0x00
#define TSEC3_PHY_ADDR  6

#define TSEC1_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC2_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS     (TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX    0
#define TSEC2_PHYIDX    0
#define TSEC3_PHYIDX    0

#define CONFIG_PHY_GIGE 1       /* Include GbE speed/duplex detection */

#endif

#define CONFIG_HOSTNAME         UCP1020
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"
#define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */

/* default location for tftp and bootm */
#define CONFIG_LOADADDR         1000000

#define CONFIG_BOOTARGS /* the boot command will set bootargs */

#define CONFIG_BAUDRATE 115200

#if defined(CONFIG_DONGLE)

#define CONFIG_BOOTDELAY 1      /* autoboot after 1 seconds */
#define CONFIG_EXTRA_ENV_SETTINGS                                       \
"bootcmd=run prog_spi_mbrbootcramfs\0"                                  \
"bootfile=uImage\0"                                                     \
"consoledev=ttyS0\0"                                                    \
"cramfsfile=image.cramfs\0"                                             \
"dtbaddr=0x00c00000\0"                                                  \
"dtbfile=image.dtb\0"                                                   \
"ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
"fileaddr=0x01000000\0"                                                 \
"filesize=0x00080000\0"                                                 \
"flashmbr=sf probe 0; "                                                 \
        "tftp $loadaddr $mbr; "                                         \
        "sf erase $mbr_offset +$filesize; "                             \
        "sf write $loadaddr $mbr_offset $filesize\0"                    \
"flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
        "protect off $nor_recoveryaddr +$filesize; "                    \
        "erase $nor_recoveryaddr +$filesize; "                          \
        "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
        "protect on $nor_recoveryaddr +$filesize\0 "                    \
"flashuboot=tftp $ubootaddr $ubootfile; "                               \
        "protect off $nor_ubootaddr +$filesize; "                       \
        "erase $nor_ubootaddr +$filesize; "                             \
        "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
        "protect on $nor_ubootaddr +$filesize\0 "                       \
"flashworking=tftp $workingaddr $cramfsfile; "                          \
        "protect off $nor_workingaddr +$filesize; "                     \
        "erase $nor_workingaddr +$filesize; "                           \
        "cp.b $workingaddr $nor_workingaddr $filesize; "                \
        "protect on $nor_workingaddr +$filesize\0 "                     \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
"kerneladdr=0x01100000\0"                                               \
"kernelfile=uImage\0"                                                   \
"loadaddr=0x01000000\0"                                                 \
"mbr=uCP1020d.mbr\0"                                                    \
"mbr_offset=0x00000000\0"                                               \
"mmbr=uCP1020Quiet.mbr\0"                                               \
"mmcpart=0:2\0"                                                         \
"mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
        "mmc erase 1 1; "                                               \
        "mmc write $loadaddr 1 1\0"                                     \
"mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; "                \
        "mmc erase 0x40 0x400; "                                        \
        "mmc write $loadaddr 0x40 0x400\0"                              \
"netdev=eth0\0"                                                         \
"nor_recoveryaddr=0xEC0A0000\0"                                         \
"nor_ubootaddr=0xEFF80000\0"                                            \
"nor_workingaddr=0xECFA0000\0"                                          \
"norbootrecovery=setenv bootargs $recoverybootargs"                     \
        " console=$consoledev,$baudrate $othbootargs; "                 \
        "run norloadrecovery; "                                         \
        "bootm $kerneladdr - $dtbaddr\0"                                \
"norbootworking=setenv bootargs $workingbootargs"                       \
        " console=$consoledev,$baudrate $othbootargs; "                 \
        "run norloadworking; "                                          \
        "bootm $kerneladdr - $dtbaddr\0"                                \
"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
        "setenv cramfsaddr $nor_recoveryaddr; "                         \
        "cramfsload $dtbaddr $dtbfile; "                                \
        "cramfsload $kerneladdr $kernelfile\0"                          \
"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
        "setenv cramfsaddr $nor_workingaddr; "                          \
        "cramfsload $dtbaddr $dtbfile; "                                \
        "cramfsload $kerneladdr $kernelfile\0"                          \
"prog_spi_mbr=run spi__mbr\0"                                           \
"prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0"       \
"prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \
        "run spi__cramfs\0"                                             \
"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
        " console=$consoledev,$baudrate $othbootargs; "                 \
        "tftp $rootfsaddr $rootfsfile; "                                \
        "tftp $loadaddr $kernelfile; "                                  \
        "tftp $dtbaddr $dtbfile; "                                      \
        "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
"ramdisk_size=120000\0"                                                 \
"ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
"recoveryaddr=0x02F00000\0"                                             \
"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
        "mw.l 0xffe0f008 0x00400000\0"                                  \
"rootfsaddr=0x02F00000\0"                                               \
"rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
"rootpath=/opt/nfsroot\0"                                               \
"spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
        "protect off 0xeC000000 +$filesize; "                           \
        "erase 0xEC000000 +$filesize; "                                 \
        "cp.b $loadaddr 0xEC000000 $filesize; "                         \
        "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
        "protect on 0xeC000000 +$filesize\0"                            \
"spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; "                \
        "protect off 0xeFF80000 +$filesize; "                           \
        "erase 0xEFF80000 +$filesize; "                                 \
        "cp.b $loadaddr 0xEFF80000 $filesize; "                         \
        "cmp.b $loadaddr 0xEFF80000 $filesize; "                        \
        "protect on 0xeFF80000 +$filesize\0"                            \
"spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; "                   \
        "sf probe 0; sf erase 0x8000 +$filesize; "                      \
        "sf write $loadaddr 0x8000 $filesize\0"                         \
"spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; "             \
        "protect off 0xec0a0000 +$filesize; "                           \
        "erase 0xeC0A0000 +$filesize; "                                 \
        "cp.b $loadaddr 0xeC0A0000 $filesize; "                         \
        "protect on 0xec0a0000 +$filesize\0"                            \
"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
        "sf probe 1; sf erase 0 +$filesize; "                           \
        "sf write $loadaddr 0 $filesize\0"                              \
"spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; "                       \
        "sf probe 0; sf erase 0 +$filesize; "                           \
        "sf write $loadaddr 0 $filesize\0"                              \
"tftpflash=tftpboot $loadaddr $uboot; "                                 \
        "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
        "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
        "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
        "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
        "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
"uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
"ubootaddr=0x01000000\0"                                                \
"ubootfile=u-boot.bin\0"                                                \
"ubootd=u-boot4dongle.bin\0"                                            \
"upgrade=run flashworking\0"                                            \
"usb_phy_type=ulpi\0 "                                                  \
"workingaddr=0x02F00000\0"                                              \
"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"

#else

#if defined(CONFIG_UCP1020T1)

#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
#define CONFIG_EXTRA_ENV_SETTINGS                                       \
"bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0"  \
"bootfile=uImage\0"                                                     \
"consoledev=ttyS0\0"                                                    \
"cramfsfile=image.cramfs\0"                                             \
"dtbaddr=0x00c00000\0"                                                  \
"dtbfile=image.dtb\0"                                                   \
"ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
"fileaddr=0x01000000\0"                                                 \
"filesize=0x00080000\0"                                                 \
"flashmbr=sf probe 0; "                                                 \
        "tftp $loadaddr $mbr; "                                         \
        "sf erase $mbr_offset +$filesize; "                             \
        "sf write $loadaddr $mbr_offset $filesize\0"                    \
"flashrecovery=tftp $recoveryaddr $cramfsfile; "                        \
        "protect off $nor_recoveryaddr +$filesize; "                    \
        "erase $nor_recoveryaddr +$filesize; "                          \
        "cp.b $recoveryaddr $nor_recoveryaddr $filesize; "              \
        "protect on $nor_recoveryaddr +$filesize\0 "                    \
"flashuboot=tftp $ubootaddr $ubootfile; "                               \
        "protect off $nor_ubootaddr +$filesize; "                       \
        "erase $nor_ubootaddr +$filesize; "                             \
        "cp.b $ubootaddr $nor_ubootaddr $filesize; "                    \
        "protect on $nor_ubootaddr +$filesize\0 "                       \
"flashworking=tftp $workingaddr $cramfsfile; "                          \
        "protect off $nor_workingaddr +$filesize; "                     \
        "erase $nor_workingaddr +$filesize; "                           \
        "cp.b $workingaddr $nor_workingaddr $filesize; "                \
        "protect on $nor_workingaddr +$filesize\0 "                     \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
"kerneladdr=0x01100000\0"                                               \
"kernelfile=uImage\0"                                                   \
"loadaddr=0x01000000\0"                                                 \
"mbr=uCP1020.mbr\0"                                                     \
"mbr_offset=0x00000000\0"                                               \
"netdev=eth0\0"                                                         \
"nor_recoveryaddr=0xEC0A0000\0"                                         \
"nor_ubootaddr=0xEFF80000\0"                                            \
"nor_workingaddr=0xECFA0000\0"                                          \
"norbootrecovery=setenv bootargs $recoverybootargs"                     \
        " console=$consoledev,$baudrate $othbootargs; "                 \
        "run norloadrecovery; "                                         \
        "bootm $kerneladdr - $dtbaddr\0"                                \
"norbootworking=setenv bootargs $workingbootargs"                       \
        " console=$consoledev,$baudrate $othbootargs; "                 \
        "run norloadworking; "                                          \
        "bootm $kerneladdr - $dtbaddr\0"                                \
"norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; "                     \
        "setenv cramfsaddr $nor_recoveryaddr; "                         \
        "cramfsload $dtbaddr $dtbfile; "                                \
        "cramfsload $kerneladdr $kernelfile\0"                          \
"norloadworking=mw.l $kerneladdr 0x0 0x00a00000; "                      \
        "setenv cramfsaddr $nor_workingaddr; "                          \
        "cramfsload $dtbaddr $dtbfile; "                                \
        "cramfsload $kerneladdr $kernelfile\0"                          \
"othbootargs=quiet\0"                                                   \
"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
        " console=$consoledev,$baudrate $othbootargs; "                 \
        "tftp $rootfsaddr $rootfsfile; "                                \
        "tftp $loadaddr $kernelfile; "                                  \
        "tftp $dtbaddr $dtbfile; "                                      \
        "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
"ramdisk_size=120000\0"                                                 \
"ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
"recoveryaddr=0x02F00000\0"                                             \
"recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0"           \
"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
        "mw.l 0xffe0f008 0x00400000\0"                                  \
"rootfsaddr=0x02F00000\0"                                               \
"rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
"rootpath=/opt/nfsroot\0"                                               \
"silent=1\0"                                                            \
"tftpflash=tftpboot $loadaddr $uboot; "                                 \
        "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
        "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
        "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
        "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
        "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
"uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
"ubootaddr=0x01000000\0"                                                \
"ubootfile=u-boot.bin\0"                                                \
"upgrade=run flashworking\0"                                            \
"workingaddr=0x02F00000\0"                                              \
"workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"

#else /* For Arcturus Modules */

#define CONFIG_BOOTDELAY 2 /* autoboot after 2 sec, -1 disables auto-boot */
#define CONFIG_EXTRA_ENV_SETTINGS                                       \
"bootcmd=run norkernel\0"                                               \
"bootfile=uImage\0"                                                     \
"consoledev=ttyS0\0"                                                    \
"dtbaddr=0x00c00000\0"                                                  \
"dtbfile=image.dtb\0"                                                   \
"ethaddr=" __stringify(CONFIG_ETHADDR) "\0"                             \
"eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0"                           \
"eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0"                           \
"fileaddr=0x01000000\0"                                                 \
"filesize=0x00080000\0"                                                 \
"flashmbr=sf probe 0; "                                                 \
        "tftp $loadaddr $mbr; "                                         \
        "sf erase $mbr_offset +$filesize; "                             \
        "sf write $loadaddr $mbr_offset $filesize\0"                    \
"flashuboot=tftp $loadaddr $ubootfile; "                                \
        "protect off $nor_ubootaddr0 +$filesize; "                      \
        "erase $nor_ubootaddr0 +$filesize; "                            \
        "cp.b $loadaddr $nor_ubootaddr0 $filesize; "                    \
        "protect on $nor_ubootaddr0 +$filesize; "                       \
        "protect off $nor_ubootaddr1 +$filesize; "                      \
        "erase $nor_ubootaddr1 +$filesize; "                            \
        "cp.b $loadaddr $nor_ubootaddr1 $filesize; "                    \
        "protect on $nor_ubootaddr1 +$filesize\0 "                      \
"format0=protect off $part0base +$part0size; "                          \
        "erase $part0base +$part0size\0"                                \
"format1=protect off $part1base +$part1size; "                          \
        "erase $part1base +$part1size\0"                                \
"format2=protect off $part2base +$part2size; "                          \
        "erase $part2base +$part2size\0"                                \
"format3=protect off $part3base +$part3size; "                          \
        "erase $part3base +$part3size\0"                                \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 "                           \
"kerneladdr=0x01100000\0"                                               \
"kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0"                 \
"kernelfile=uImage\0"                                                   \
"loadaddr=0x01000000\0"                                                 \
"mbr=uCP1020.mbr\0"                                                     \
"mbr_offset=0x00000000\0"                                               \
"netdev=eth0\0"                                                         \
"nor_ubootaddr0=0xEC000000\0"                                           \
"nor_ubootaddr1=0xEFF80000\0"                                           \
"norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \
        "run norkernelload; "                                           \
        "bootm $kerneladdr - $dtbaddr\0"                                \
"norkernelload=mw.l $kerneladdr 0x0 0x00a00000; "                       \
        "setenv cramfsaddr $part0base; "                                \
        "cramfsload $dtbaddr $dtbfile; "                                \
        "cramfsload $kerneladdr $kernelfile\0"                          \
"part0base=0xEC100000\0"                                                \
"part0size=0x00700000\0"                                                \
"part1base=0xEC800000\0"                                                \
"part1size=0x02000000\0"                                                \
"part2base=0xEE800000\0"                                                \
"part2size=0x00800000\0"                                                \
"part3base=0xEF000000\0"                                                \
"part3size=0x00F80000\0"                                                \
"partENVbase=0xEC080000\0"                                              \
"partENVsize=0x00080000\0"                                              \
"program0=tftp part0-000000.bin; "                                      \
        "protect off $part0base +$filesize; "                           \
        "erase $part0base +$filesize; "                                 \
        "cp.b $loadaddr $part0base $filesize; "                         \
        "echo Verifying...; "                                           \
        "cmp.b $loadaddr $part0base $filesize\0"                        \
"program1=tftp part1-000000.bin; "                                      \
        "protect off $part1base +$filesize; "                           \
        "erase $part1base +$filesize; "                                 \
        "cp.b $loadaddr $part1base $filesize; "                         \
        "echo Verifying...; "                                           \
        "cmp.b $loadaddr $part1base $filesize\0"                        \
"program2=tftp part2-000000.bin; "                                      \
        "protect off $part2base +$filesize; "                           \
        "erase $part2base +$filesize; "                                 \
        "cp.b $loadaddr $part2base $filesize; "                         \
        "echo Verifying...; "                                           \
        "cmp.b $loadaddr $part2base $filesize\0"                        \
"ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro"   \
        "  console=$consoledev,$baudrate $othbootargs; "                \
        "tftp $rootfsaddr $rootfsfile; "                                \
        "tftp $loadaddr $kernelfile; "                                  \
        "tftp $dtbaddr $dtbfile; "                                      \
        "bootm $loadaddr $rootfsaddr $dtbaddr\0"                        \
"ramdisk_size=120000\0"                                                 \
"ramdiskfile=rootfs.ext2.gz.uboot\0"                                    \
"releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; "  \
        "mw.l 0xffe0f008 0x00400000\0"                                  \
"rootfsaddr=0x02F00000\0"                                               \
"rootfsfile=rootfs.ext2.gz.uboot\0"                                     \
"rootpath=/opt/nfsroot\0"                                               \
"spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; "                       \
        "sf probe 0; sf erase 0 +$filesize; "                           \
        "sf write $loadaddr 0 $filesize\0"                              \
"spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; "                 \
        "protect off 0xeC000000 +$filesize; "                           \
        "erase 0xEC000000 +$filesize; "                                 \
        "cp.b $loadaddr 0xEC000000 $filesize; "                         \
        "cmp.b $loadaddr 0xEC000000 $filesize; "                        \
        "protect on 0xeC000000 +$filesize\0"                            \
"tftpflash=tftpboot $loadaddr $uboot; "                                 \
        "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
        "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; "  \
        "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \
        "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \
        "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\
"uboot= " __stringify(CONFIG_UBOOTPATH) "\0"                            \
"ubootfile=u-boot.bin\0"                                                \
"upgrade=run flashuboot\0"                                              \
"usb_phy_type=ulpi\0 "                                                  \
"boot_nfs= "                                                            \
        "setenv bootargs root=/dev/nfs rw "                             \
        "nfsroot=$serverip:$rootpath "                                  \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;"                   \
        "tftp $loadaddr $bootfile;"                                     \
        "tftp $fdtaddr $fdtfile;"                                       \
        "bootm $loadaddr - $fdtaddr\0"                                  \
"boot_hd = "                                                            \
        "setenv bootargs root=/dev/$bdev rw rootdelay=30 "              \
        "console=$consoledev,$baudrate $othbootargs;"                   \
        "usb start;"                                                    \
        "ext2load usb 0:1 $loadaddr /boot/$bootfile;"                   \
        "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"                     \
        "bootm $loadaddr - $fdtaddr\0"                                  \
"boot_usb_fat = "                                                       \
        "setenv bootargs root=/dev/ram rw "                             \
        "console=$consoledev,$baudrate $othbootargs "                   \
        "ramdisk_size=$ramdisk_size;"                                   \
        "usb start;"                                                    \
        "fatload usb 0:2 $loadaddr $bootfile;"                          \
        "fatload usb 0:2 $fdtaddr $fdtfile;"                            \
        "fatload usb 0:2 $ramdiskaddr $ramdiskfile;"                    \
        "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
"boot_usb_ext2 = "                                                      \
        "setenv bootargs root=/dev/ram rw "                             \
        "console=$consoledev,$baudrate $othbootargs "                   \
        "ramdisk_size=$ramdisk_size;"                                   \
        "usb start;"                                                    \
        "ext2load usb 0:4 $loadaddr $bootfile;"                         \
        "ext2load usb 0:4 $fdtaddr $fdtfile;"                           \
        "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"                   \
        "bootm $loadaddr $ramdiskaddr $fdtaddr\0 "                      \
"boot_nor = "                                                           \
        "setenv bootargs root=/dev/$jffs2nor rw "                       \
        "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"  \
        "bootm $norbootaddr - $norfdtaddr\0 "                           \
"boot_ram = "                                                           \
        "setenv bootargs root=/dev/ram rw "                             \
        "console=$consoledev,$baudrate $othbootargs "                   \
        "ramdisk_size=$ramdisk_size;"                                   \
        "tftp $ramdiskaddr $ramdiskfile;"                               \
        "tftp $loadaddr $bootfile;"                                     \
        "tftp $fdtaddr $fdtfile;"                                       \
        "bootm $loadaddr $ramdiskaddr $fdtaddr\0"

#endif
#endif

#endif /* __CONFIG_H */