include/configs/VOM405.h

   1 /*
   2  * (C) Copyright 2001-2004
   3  * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  * (easy to change)
  17  */
  18 #define CONFIG_405EP            1       /* This is a PPC405 CPU         */
  19 #define CONFIG_VOM405           1       /* ...on a VOM405 board         */
  20
  21 #define CONFIG_SYS_TEXT_BASE    0xFFFC8000
  22 #define CONFIG_DISPLAY_BOARDINFO
  23
  24 #define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()    */
  25 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
  26
  27 #define CONFIG_SYS_CLK_FREQ     33330000 /* external frequency to pll   */
  28
  29 #define CONFIG_BAUDRATE         9600
  30 #define CONFIG_BOOTDELAY        3       /* autoboot after 3 seconds     */
  31
  32 #undef  CONFIG_BOOTARGS
  33 #undef  CONFIG_BOOTCOMMAND
  34
  35 #define CONFIG_PREBOOT                  /* enable preboot variable      */
  36
  37 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
  38
  39 #undef  CONFIG_HAS_ETH1
  40
  41 #define CONFIG_PPC4xx_EMAC
  42 #define CONFIG_MII              1       /* MII PHY management           */
  43 #define CONFIG_PHY_ADDR         0       /* PHY address                  */
  44 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
  45 #define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
  46
  47 /*
  48  * BOOTP options
  49  */
  50 #define CONFIG_BOOTP_SUBNETMASK
  51 #define CONFIG_BOOTP_GATEWAY
  52 #define CONFIG_BOOTP_HOSTNAME
  53 #define CONFIG_BOOTP_BOOTPATH
  54 #define CONFIG_BOOTP_DNS
  55 #define CONFIG_BOOTP_DNS2
  56 #define CONFIG_BOOTP_SEND_HOSTNAME
  57
  58 /*
  59  * Command line configuration.
  60  */
  61 #define CONFIG_CMD_BSP
  62 #define CONFIG_CMD_IRQ
  63 #define CONFIG_CMD_MII
  64 #define CONFIG_CMD_EEPROM
  65
  66 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  67
  68 #define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */
  69
  70 #undef  CONFIG_PRAM                     /* no "protected RAM"           */
  71
  72 /*
  73  * Miscellaneous configurable options
  74  */
  75 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
  76
  77 #if defined(CONFIG_CMD_KGDB)
  78 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
  79 #else
  80 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
  81 #endif
  82 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
  83 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
  84 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
  85
  86 #define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */
  87
  88 #define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup*/
  89
  90 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
  91 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
  92
  93 #define CONFIG_CONS_INDEX       1       /* Use UART0                    */
  94 #define CONFIG_SYS_NS16550_SERIAL
  95 #define CONFIG_SYS_NS16550_REG_SIZE     1
  96 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
  97
  98 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
  99 #define CONFIG_SYS_BASE_BAUD        691200
 100
 101 /* The following table includes the supported baudrates */
 102 #define CONFIG_SYS_BAUDRATE_TABLE       \
 103         { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 104          57600, 115200, 230400, 460800, 921600 }
 105
 106 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 107 #define CONFIG_SYS_EXTBDINFO    1               /* To use extended board_into (bd_t) */
 108
 109 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 110 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 111
 112 #define CONFIG_VERSION_VARIABLE 1       /* include version env variable */
 113
 114 #define CONFIG_SYS_RX_ETH_BUFFER        16      /* use 16 rx buffer on 405 emac */
 115
 116 /*
 117  * For booting Linux, the board info and command line data
 118  * have to be in the first 8 MB of memory, since this is
 119  * the maximum mapped by the Linux kernel during initialization.
 120  */
 121 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 122 /*
 123  * FLASH organization
 124  */
 125 #define FLASH_BASE0_PRELIM      0xFFC00000      /* FLASH bank #0        */
 126
 127 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks           */
 128 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip    */
 129
 130 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
 131 #define CONFIG_SYS_FLASH_WRITE_TOUT     1000    /* Timeout for Flash Write (in ms)      */
 132
 133 #define CONFIG_SYS_FLASH_WORD_SIZE      unsigned short  /* flash word size (width)      */
 134 #define CONFIG_SYS_FLASH_ADDR0          0x5555  /* 1st address for flash config cycles  */
 135 #define CONFIG_SYS_FLASH_ADDR1          0x2AAA  /* 2nd address for flash config cycles  */
 136 /*
 137  * The following defines are added for buggy IOP480 byte interface.
 138  * All other boards should use the standard values (CPCI405 etc.)
 139  */
 140 #define CONFIG_SYS_FLASH_READ0          0x0000  /* 0 is standard                        */
 141 #define CONFIG_SYS_FLASH_READ1          0x0001  /* 1 is standard                        */
 142 #define CONFIG_SYS_FLASH_READ2          0x0002  /* 2 is standard                        */
 143
 144 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* print 'E' for empty sector on flinfo */
 145
 146 /*
 147  * Start addresses for the final memory configuration
 148  * (Set up by the startup code)
 149  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 150  */
 151 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 152 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_MONITOR_BASE
 153 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 154 #define CONFIG_SYS_MONITOR_LEN          (~(CONFIG_SYS_TEXT_BASE) + 1)
 155 #define CONFIG_SYS_MALLOC_LEN           (256 * 1024)
 156
 157 #if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
 158 # define CONFIG_SYS_RAMBOOT             1
 159 #else
 160 # undef CONFIG_SYS_RAMBOOT
 161 #endif
 162
 163 /*
 164  * Environment Variable setup
 165  */
 166 #define CONFIG_ENV_IS_IN_EEPROM 1       /* use EEPROM for environment vars */
 167 #define CONFIG_ENV_OFFSET               0x100   /* environment starts at the beginning of the EEPROM */
 168 #define CONFIG_ENV_SIZE         0x700   /* 2048 bytes may be used for env vars*/
 169                                    /* total size of a CAT24WC16 is 2048 bytes */
 170
 171 #define CONFIG_SYS_NVRAM_BASE_ADDR      0xF0000500              /* NVRAM base address   */
 172 #define CONFIG_SYS_NVRAM_SIZE           242                     /* NVRAM size           */
 173
 174 /*
 175  * I2C EEPROM (CAT24WC16) for environment
 176  */
 177 #define CONFIG_SYS_I2C
 178 #define CONFIG_SYS_I2C_PPC4XX
 179 #define CONFIG_SYS_I2C_PPC4XX_CH0
 180 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0           400000
 181 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0           0x7F
 182
 183 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM CAT28WC08             */
 184 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1        /* Bytes of address             */
 185 /* mask of address bits that overflow into the "EEPROM chip address"    */
 186 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
 187 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4     /* The Catalyst CAT24WC08 has   */
 188                                         /* 16 byte page write mode using*/
 189                                         /* last 4 bits of the address   */
 190 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */
 191
 192 /*
 193  * External Bus Controller (EBC) Setup
 194  */
 195 #define CAN_BA          0xF0000000          /* CAN Base Address                 */
 196
 197 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
 198 #define CONFIG_SYS_EBC_PB0AP            0x92015480
 199 #define CONFIG_SYS_EBC_PB0CR            0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 200
 201 /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
 202 #define CONFIG_SYS_EBC_PB2AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 203 #define CONFIG_SYS_EBC_PB2CR            0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
 204
 205 /*
 206  * FPGA stuff
 207  */
 208 #define CONFIG_SYS_XSVF_DEFAULT_ADDR    0xfffc0000
 209
 210 /* FPGA program pin configuration */
 211 #define CONFIG_SYS_FPGA_PRG             0x04000000  /* JTAG TMS pin (ppc output)     */
 212 #define CONFIG_SYS_FPGA_CLK             0x02000000  /* JTAG TCK pin (ppc output)     */
 213 #define CONFIG_SYS_FPGA_DATA            0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
 214 #define CONFIG_SYS_FPGA_INIT            0x00010000  /* unused (ppc input)            */
 215 #define CONFIG_SYS_FPGA_DONE            0x00008000  /* JTAG TDI->TDO pin (ppc input) */
 216
 217 /*
 218  * Definitions for initial stack pointer and data area (in data cache)
 219  */
 220 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
 221 #define CONFIG_SYS_TEMP_STACK_OCM         1
 222
 223 /* On Chip Memory location */
 224 #define CONFIG_SYS_OCM_DATA_ADDR        0xF8000000
 225 #define CONFIG_SYS_OCM_DATA_SIZE        0x1000
 226 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM             */
 227 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM    */
 228
 229 #define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 230 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 231
 232 /*
 233  * Definitions for GPIO setup (PPC405EP specific)
 234  *
 235  * GPIO0[0]     - External Bus Controller BLAST output
 236  * GPIO0[1-9]   - Instruction trace outputs -> GPIO
 237  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 238  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 239  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 240  * GPIO0[24-27] - UART0 control signal inputs/outputs
 241  * GPIO0[28-29] - UART1 data signal input/output
 242  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 243  */
 244 /* GPIO Input:          OSR=00, ISR=00, TSR=00, TCR=0 */
 245 /* GPIO Output:         OSR=00, ISR=00, TSR=00, TCR=1 */
 246 /* Alt. Funtion Input:  OSR=00, ISR=01, TSR=00, TCR=0 */
 247 /* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
 248 #define CONFIG_SYS_GPIO0_OSRL           0x40000500  /*  0 ... 15 */
 249 #define CONFIG_SYS_GPIO0_OSRH           0x00000110  /* 16 ... 31 */
 250 #define CONFIG_SYS_GPIO0_ISR1L          0x00000000  /*  0 ... 15 */
 251 #define CONFIG_SYS_GPIO0_ISR1H          0x14000045  /* 16 ... 31 */
 252 #define CONFIG_SYS_GPIO0_TSRL           0x00000000  /*  0 ... 15 */
 253 #define CONFIG_SYS_GPIO0_TSRH           0x00000000  /* 16 ... 31 */
 254 #define CONFIG_SYS_GPIO0_TCR            0xF7FE0014  /*  0 ... 31 */
 255
 256 /*
 257  * Default speed selection (cpu_plb_opb_ebc) in mhz.
 258  * This value will be set if iic boot eprom is disabled.
 259  */
 260 #define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
 261 #define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
 262
 263 #endif  /* __CONFIG_H */