include/configs/a4m072.h

   1 /*
   2  * (C) Copyright 2003-2005
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * (C) Copyright 2010
   6  * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * High Level Configuration Options
  16  * (easy to change)
  17  */
  18
  19 #define CONFIG_MPC5200          1       /* This is a MPC5200 CPU */
  20 #define CONFIG_A4M072           1       /* ... on A4M072 board */
  21 #define CONFIG_MPC5200_DDR      1       /* ... use DDR RAM */
  22 #define CONFIG_DISPLAY_BOARDINFO
  23 #define CONFIG_SYS_GENERIC_BOARD
  24
  25 #define CONFIG_SYS_TEXT_BASE    0xFE000000
  26
  27 #define CONFIG_MISC_INIT_R
  28
  29 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000 /* ... running at 33.000000MHz */
  30
  31 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  32
  33 /*
  34  * Serial console configuration
  35  */
  36 #define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
  37 #define CONFIG_BAUDRATE         9600    /* ... at 9600 bps */
  38 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  39 /* define to enable silent console */
  40 #define CONFIG_SILENT_CONSOLE
  41 #define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device */
  42
  43 /*
  44  * PCI Mapping:
  45  * 0x40000000 - 0x4fffffff - PCI Memory
  46  * 0x50000000 - 0x50ffffff - PCI IO Space
  47  */
  48 #define CONFIG_PCI
  49
  50 #if defined(CONFIG_PCI)
  51 #define CONFIG_PCI_PNP          1
  52 #define CONFIG_PCI_SCAN_SHOW    1
  53 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
  54
  55 #define CONFIG_PCI_MEM_BUS      0x40000000
  56 #define CONFIG_PCI_MEM_PHYS     CONFIG_PCI_MEM_BUS
  57 #define CONFIG_PCI_MEM_SIZE     0x10000000
  58
  59 #define CONFIG_PCI_IO_BUS       0x50000000
  60 #define CONFIG_PCI_IO_PHYS      CONFIG_PCI_IO_BUS
  61 #define CONFIG_PCI_IO_SIZE      0x01000000
  62 #endif
  63
  64 #define CONFIG_SYS_XLB_PIPELINING       1
  65
  66 #undef CONFIG_EEPRO100
  67
  68 /* Partitions */
  69 #define CONFIG_MAC_PARTITION
  70 #define CONFIG_DOS_PARTITION
  71
  72 /* USB */
  73 #define CONFIG_USB_OHCI_NEW
  74 #define CONFIG_USB_STORAGE
  75 #define CONFIG_SYS_OHCI_BE_CONTROLLER
  76 #undef CONFIG_SYS_USB_OHCI_BOARD_INIT
  77 #define CONFIG_SYS_USB_OHCI_CPU_INIT    1
  78 #define CONFIG_SYS_USB_OHCI_REGS_BASE   MPC5XXX_USB
  79 #define CONFIG_SYS_USB_OHCI_SLOT_NAME   "mpc5200"
  80 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
  81
  82 #define CONFIG_TIMESTAMP                /* Print image info with timestamp */
  83
  84 /*
  85  * BOOTP options
  86  */
  87 #define CONFIG_BOOTP_BOOTFILESIZE
  88 #define CONFIG_BOOTP_BOOTPATH
  89 #define CONFIG_BOOTP_GATEWAY
  90 #define CONFIG_BOOTP_HOSTNAME
  91
  92
  93 /*
  94  * Command line configuration.
  95  */
  96 #include <config_cmd_default.h>
  97
  98 #define CONFIG_CMD_EEPROM
  99 #define CONFIG_CMD_FAT
 100 #define CONFIG_CMD_I2C
 101 #define CONFIG_CMD_IDE
 102 #define CONFIG_CMD_NFS
 103 #define CONFIG_CMD_SNTP
 104 #define CONFIG_CMD_USB
 105 #define CONFIG_CMD_MII
 106 #define CONFIG_CMD_DHCP
 107 #define CONFIG_CMD_PING
 108 #define CONFIG_CMD_DISPLAY
 109
 110 #if defined(CONFIG_PCI)
 111 #define CONFIG_CMD_PCI
 112 #endif
 113
 114 #if (CONFIG_SYS_TEXT_BASE == 0xFE000000)                /* Boot low with 32 MB Flash */
 115 #define CONFIG_SYS_LOWBOOT              1
 116 #define CONFIG_SYS_LOWBOOT32            1
 117 #endif
 118
 119 /*
 120  * Autobooting
 121  */
 122 #define CONFIG_BOOTDELAY        2       /* autoboot after 2 seconds */
 123
 124 #define CONFIG_SYS_AUTOLOAD     "n"
 125
 126 #define CONFIG_AUTOBOOT_KEYED
 127 #define CONFIG_AUTOBOOT_PROMPT          "autoboot in %d seconds\n", bootdelay
 128 #define CONFIG_AUTOBOOT_DELAY_STR       "asdfg"
 129
 130 #undef  CONFIG_BOOTARGS
 131 #define CONFIG_PREBOOT                          "run try_update"
 132
 133 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 134         "bk=run add_mtd ; run add_consolespec ; bootm 200000\0"         \
 135         "cf1=diskboot 200000 0:1\0"                                     \
 136         "bootcmd_cf1=run bcf1\0"                                        \
 137         "bcf=setenv bootargs root=/dev/hda3\0"                          \
 138         "bootcmd_nfs=run bnfs\0"                                        \
 139         "norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs "\
 140                 "panic=1\0"                                             \
 141         "bootcmd_nor=cp.b ${kernel_addr} 200000 100000;"                \
 142                         "run norargs addip; run bk\0"                   \
 143         "bnfs=nfs 200000 ${rootpath}/boot/uImage;"                      \
 144                         "run nfsargs addip ; run bk\0"                  \
 145         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 146                                 "nfsroot=${serverip}:${rootpath}\0"     \
 147         "try_update=usb start;sleep 2;usb start;sleep 1;"               \
 148                         "fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;"   \
 149                         "source 2F0000\0"                               \
 150         "env_addr=FE060000\0"                                           \
 151         "kernel_addr=FE100000\0"                                        \
 152         "rootfs_addr=FE200000\0"                                        \
 153         "add_mtd=setenv bootargs ${bootargs} mtdparts="                 \
 154                 "phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0"      \
 155         "bcf1=run cf1; run bcf; run addip; run bk\0"                    \
 156         "add_consolespec=setenv bootargs ${bootargs} "                  \
 157                                 "console=/dev/null quiet\0"             \
 158         "addip=if test -n ${ethaddr};"                                  \
 159                 "then if test -n ${ipaddr};"                            \
 160                         "then setenv bootargs ${bootargs} "             \
 161                                 "ip=${ipaddr}:${serverip}:${gatewayip}:"\
 162                                 "${netmask}:${hostname}:${netdev}:off;" \
 163                         "fi;"                                           \
 164                 "else;"                                                 \
 165                         "setenv bootargs ${bootargs} no_ethaddr;"       \
 166                 "fi\0"                                                  \
 167         "hostname=CPUP0\0"                                              \
 168         "ethaddr=00:00:00:00:00:00\0"                                   \
 169         "netdev=eth0\0"                                                 \
 170         "bootcmd=run bootcmd_nor\0"                                     \
 171         ""
 172 /*
 173  * IPB Bus clocking configuration.
 174  */
 175 #undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK          /* define for 133MHz speed */
 176
 177 /*
 178  * I2C configuration
 179  */
 180 #define CONFIG_HARD_I2C                 1       /* I2C with hardware support */
 181 #define CONFIG_SYS_I2C_MODULE           2       /* Select I2C module #1 or #2 */
 182
 183 #define CONFIG_SYS_I2C_SPEED            100000 /* 100 kHz */
 184 #define CONFIG_SYS_I2C_SLAVE            0x7F
 185
 186 /*
 187  * EEPROM configuration
 188  */
 189 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x52    /* 1010010x */
 190 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 191 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6
 192 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10
 193 #define CONFIG_SYS_EEPROM_WREN                  1
 194 #define CONFIG_SYS_EEPROM_WP                    GPIO_PSC2_4
 195
 196 /*
 197  * Flash configuration
 198  */
 199 #define CONFIG_SYS_FLASH_BASE           0xFE000000
 200 #define CONFIG_SYS_FLASH_SIZE           0x02000000
 201 #if !defined(CONFIG_SYS_LOWBOOT)
 202 #error "CONFIG_SYS_LOWBOOT not defined?"
 203 #else   /* CONFIG_SYS_LOWBOOT */
 204 #if defined(CONFIG_SYS_LOWBOOT32)
 205 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + 0x00060000)
 206 #endif
 207 #endif  /* CONFIG_SYS_LOWBOOT */
 208
 209 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
 210 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max num of sects on one chip */
 211 #define CONFIG_FLASH_CFI_DRIVER
 212 #define CONFIG_SYS_FLASH_CFI
 213 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 214 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_CS0_START}
 215 #define CONFIG_SYS_FLASH_BANKS_SIZES    {CONFIG_SYS_CS0_SIZE}
 216
 217 /*
 218  * Environment settings
 219  */
 220 #define CONFIG_ENV_IS_IN_FLASH  1
 221 #define CONFIG_ENV_SIZE         0x10000
 222 #define CONFIG_ENV_SECT_SIZE    0x20000
 223 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 224 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 225
 226 #define CONFIG_ENV_OVERWRITE    1
 227
 228 /*
 229  * Memory map
 230  */
 231 #define CONFIG_SYS_MBAR         0xF0000000
 232 #define CONFIG_SYS_SDRAM_BASE   0x00000000
 233 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 234
 235 /* Use SRAM until RAM will be available */
 236 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 237 #define CONFIG_SYS_INIT_RAM_SIZE                MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 238
 239
 240 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 241 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 242
 243 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 244 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 245 #   define CONFIG_SYS_RAMBOOT           1
 246 #endif
 247
 248 #define CONFIG_SYS_MONITOR_LEN          (384 << 10)     /* Reserve 384 kB for Monitor   */
 249 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 250 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 251
 252 /*
 253  * Ethernet configuration
 254  */
 255 #define CONFIG_MPC5xxx_FEC      1
 256 #define CONFIG_MPC5xxx_FEC_MII100
 257 /*
 258  * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
 259  */
 260 /* #define CONFIG_MPC5xxx_FEC_MII10 */
 261 #define CONFIG_PHY_ADDR         0x1f
 262 #define CONFIG_PHY_TYPE         0x79c874                /* AMD Phy Controller */
 263
 264 /*
 265  * GPIO configuration
 266  */
 267 #define CONFIG_SYS_GPS_PORT_CONFIG      0x18000004
 268
 269 /*
 270  * Miscellaneous configurable options
 271  */
 272 #define CONFIG_SYS_HUSH_PARSER
 273 #define CONFIG_CMDLINE_EDITING  1
 274 #define CONFIG_SYS_LONGHELP                     /* undef to save memory     */
 275 #if defined(CONFIG_CMD_KGDB)
 276 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 277 #else
 278 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 279 #endif
 280 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 281 #define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
 282 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 283
 284 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 285 #define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 286
 287 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 288
 289 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 290 #if defined(CONFIG_CMD_KGDB)
 291 #  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
 292 #endif
 293
 294
 295 /*
 296  * Various low-level settings
 297  */
 298 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 299 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 300 /* Flash at CSBoot, CS0 */
 301 #define CONFIG_SYS_BOOTCS_START         CONFIG_SYS_FLASH_BASE
 302 #define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
 303 #define CONFIG_SYS_BOOTCS_CFG           0x0002DD00
 304 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 305 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 306 /* External SRAM at CS1 */
 307 #define CONFIG_SYS_CS1_START            0x62000000
 308 #define CONFIG_SYS_CS1_SIZE             0x00400000
 309 #define CONFIG_SYS_CS1_CFG              0x00009930
 310 #define CONFIG_SYS_SRAM_BASE            CONFIG_SYS_CS1_START
 311 #define CONFIG_SYS_SRAM_SIZE            CONFIG_SYS_CS1_SIZE
 312 /* LED display at CS7 */
 313 #define CONFIG_SYS_CS7_START            0x6a000000
 314 #define CONFIG_SYS_CS7_SIZE             (64*1024)
 315 #define CONFIG_SYS_CS7_CFG              0x0000bf30
 316
 317 #define CONFIG_SYS_CS_BURST             0x00000000
 318 #define CONFIG_SYS_CS_DEADCYCLE         0x33333003
 319
 320 #define CONFIG_SYS_RESET_ADDRESS        0xff000000
 321
 322 /*-----------------------------------------------------------------------
 323  * USB stuff
 324  *-----------------------------------------------------------------------
 325  */
 326 #define CONFIG_USB_CLOCK        0x0001BBBB
 327 #define CONFIG_USB_CONFIG       0x00001000 /* 0x4000 for SE mode */
 328
 329 /*-----------------------------------------------------------------------
 330  * IDE/ATA stuff Supports IDE harddisk
 331  *-----------------------------------------------------------------------
 332  */
 333
 334 #undef  CONFIG_IDE_8xx_PCCARD           /* Use IDE with PC Card Adapter */
 335
 336 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 337 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 338
 339 #define CONFIG_IDE_PREINIT
 340
 341 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 342 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 2 drives per IDE bus    */
 343
 344 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 345
 346 #define CONFIG_SYS_ATA_BASE_ADDR        MPC5XXX_ATA
 347
 348 /* Offset for data I/O                  */
 349 #define CONFIG_SYS_ATA_DATA_OFFSET      (0x0060)
 350
 351 /* Offset for normal register accesses  */
 352 #define CONFIG_SYS_ATA_REG_OFFSET       (CONFIG_SYS_ATA_DATA_OFFSET)
 353
 354 /* Offset for alternate registers       */
 355 #define CONFIG_SYS_ATA_ALT_OFFSET       (0x005C)
 356
 357 /* Interval between registers                                                */
 358 #define CONFIG_SYS_ATA_STRIDE          4
 359
 360 #define CONFIG_ATAPI                   1
 361
 362 /*-----------------------------------------------------------------------
 363  * Open firmware flat tree support
 364  *-----------------------------------------------------------------------
 365  */
 366 #define CONFIG_OF_LIBFDT        1
 367 #define CONFIG_OF_BOARD_SETUP   1
 368
 369 #define OF_CPU                  "PowerPC,5200@0"
 370 #define OF_SOC                  "soc5200@f0000000"
 371 #define OF_TBCLK                (bd->bi_busfreq / 4)
 372 #define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"
 373
 374 /* Support for the 7-segment display */
 375 #define CONFIG_SYS_DISP_CHR_RAM      CONFIG_SYS_CS7_START
 376 #define CONFIG_SHOW_ACTIVITY            /* used for display realization */
 377
 378 #define CONFIG_SHOW_BOOT_PROGRESS
 379
 380 #endif /* __CONFIG_H */