include/configs/amcc-common.h

   1 /*
   2  * (C) Copyright 2008, 2009
   3  * Stefan Roese, DENX Software Engineering, sr@denx.de.
   4  *
   5  * Common configuration options for all AMCC boards
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __AMCC_COMMON_H
  11 #define __AMCC_COMMON_H
  12
  13 #define CONFIG_SYS_GENERIC_BOARD
  14
  15 #define CONFIG_SYS_SDRAM_BASE           0x00000000      /* _must_ be 0          */
  16 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* Start of U-Boot      */
  17 #define CONFIG_SYS_MONITOR_LEN          (0xFFFFFFFF - CONFIG_SYS_MONITOR_BASE + 1)
  18 #define CONFIG_SYS_MALLOC_LEN           (1 << 20)       /* Reserved for malloc  */
  19
  20 /*
  21  * UART
  22  */
  23 #define CONFIG_SYS_NS16550
  24 #define CONFIG_SYS_NS16550_SERIAL
  25 #ifndef CONFIG_DM_SERIAL
  26 #define CONFIG_SYS_NS16550_REG_SIZE     1
  27 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
  28 #endif
  29 #define CONFIG_BAUDRATE         115200
  30 #define CONFIG_SYS_BAUDRATE_TABLE  \
  31     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
  32
  33 /*
  34  * I2C
  35  */
  36 #define CONFIG_SYS_I2C
  37 #define CONFIG_SYS_I2C_PPC4XX
  38 #define CONFIG_SYS_I2C_PPC4XX_CH0
  39 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0           0x7F
  40
  41 /*
  42  * Ethernet/EMAC/PHY
  43  */
  44 #define CONFIG_PPC4xx_EMAC
  45 #define CONFIG_MII                      /* MII PHY management           */
  46 #define CONFIG_NETCONSOLE               /* include NetConsole support   */
  47 #if defined(CONFIG_440)
  48 #define CONFIG_SYS_RX_ETH_BUFFER        32      /* number of eth rx buffers     */
  49 #else
  50 #define CONFIG_SYS_RX_ETH_BUFFER        16      /* number of eth rx buffers     */
  51 #endif
  52
  53 /*
  54  * Commands
  55  */
  56 #include <config_cmd_default.h>
  57
  58 #define CONFIG_CMD_ASKENV
  59 #if defined(CONFIG_440)
  60 #define CONFIG_CMD_CACHE
  61 #endif
  62 #define CONFIG_CMD_DHCP
  63 #define CONFIG_CMD_DIAG
  64 #define CONFIG_CMD_EEPROM
  65 #define CONFIG_CMD_ELF
  66 #define CONFIG_CMD_GREPENV
  67 #define CONFIG_CMD_I2C
  68 #define CONFIG_CMD_IRQ
  69 #define CONFIG_CMD_MII
  70 #define CONFIG_CMD_NET
  71 #define CONFIG_CMD_NFS
  72 #define CONFIG_CMD_PING
  73 #define CONFIG_CMD_REGINFO
  74 #define CONFIG_CMD_SETEXPR
  75
  76 /*
  77  * Miscellaneous configurable options
  78  */
  79 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds     */
  80 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
  81 #if defined(CONFIG_CMD_KGDB)
  82 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
  83 #else
  84 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
  85 #endif
  86 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
  87 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
  88 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size  */
  89
  90 #define CONFIG_SYS_MEMTEST_START        0x0400000 /* memtest works on           */
  91 #define CONFIG_SYS_MEMTEST_END          0x0C00000 /* 4 ... 12 MB in DRAM        */
  92
  93 #define CONFIG_SYS_LOAD_ADDR            0x100000  /* default load address       */
  94 #define CONFIG_SYS_EXTBDINFO                    /* To use extended board_into (bd_t) */
  95
  96 #define CONFIG_CMDLINE_EDITING          /* add command line history     */
  97 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support   */
  98 #define CONFIG_LOOPW                    /* enable loopw command         */
  99 #define CONFIG_MX_CYCLIC                /* enable mdc/mwc commands      */
 100 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 101 #define CONFIG_VERSION_VARIABLE         /* include version env variable */
 102 #define CONFIG_SYS_CONSOLE_INFO_QUIET   /* don't print console @ startup*/
 103
 104 #define CONFIG_SYS_HUSH_PARSER          /* Use the HUSH parser          */
 105
 106 #define CONFIG_LOADS_ECHO               /* echo on for serial download  */
 107 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change        */
 108
 109 #define CONFIG_REGEX                    /* Enable regular expression support */
 110 /*
 111  * BOOTP options
 112  */
 113 #define CONFIG_BOOTP_BOOTFILESIZE
 114 #define CONFIG_BOOTP_BOOTPATH
 115 #define CONFIG_BOOTP_GATEWAY
 116 #define CONFIG_BOOTP_HOSTNAME
 117 #define CONFIG_BOOTP_SUBNETMASK
 118
 119 /*
 120  * For booting Linux, the board info and command line data
 121  * have to be in the first 16 MB of memory, since this is
 122  * the maximum mapped by the 40x Linux kernel during initialization.
 123  */
 124 #define CONFIG_SYS_BOOTMAPSZ            (16 << 20) /* Initial Memory map for Linux */
 125 #define CONFIG_SYS_BOOTM_LEN            (16 << 20) /* Increase max gunzip size */
 126
 127 /*
 128  * Internal Definitions
 129  */
 130 #if defined(CONFIG_CMD_KGDB)
 131 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port*/
 132 #endif
 133
 134 /*
 135  * Pass open firmware flat tree
 136  */
 137 #define CONFIG_OF_LIBFDT
 138 #define CONFIG_OF_BOARD_SETUP
 139 /* Update size in "reg" property of NOR FLASH device tree nodes */
 140 #define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
 141
 142 /*
 143  * Booting and default environment
 144  */
 145 #define CONFIG_PREBOOT  "echo;" \
 146         "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
 147         "echo"
 148 #define CONFIG_BOOTCOMMAND      "run flash_self"
 149
 150 /*
 151  * Only very few boards have default console not on ttyS0 (like Taishan)
 152  */
 153 #if !defined(CONFIG_USE_TTY)
 154 #define CONFIG_USE_TTY  ttyS0
 155 #endif
 156
 157 /*
 158  * Only very few boards have default netdev not set to eth0 (like Arches)
 159  */
 160 #if !defined(CONFIG_USE_NETDEV)
 161 #define CONFIG_USE_NETDEV       eth0
 162 #endif
 163
 164 /*
 165  * Only some 4xx PPC's are equipped with an FPU
 166  */
 167 #if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
 168     defined(CONFIG_460EX) || defined(CONFIG_460GT)
 169 #define CONFIG_AMCC_DEF_ENV_ROOTPATH    "rootpath=/opt/eldk/ppc_4xxFP\0"
 170 #else
 171 #define CONFIG_AMCC_DEF_ENV_ROOTPATH    "rootpath=/opt/eldk/ppc_4xx\0"
 172 #endif
 173
 174 /*
 175  * Only some boards need to extend the bootargs by some additional
 176  * parameters (like Makalu)
 177  */
 178 #if !defined(CONFIG_ADDMISC)
 179 #define CONFIG_ADDMISC  "addmisc=setenv bootargs ${bootargs}\0"
 180 #endif
 181
 182 /*
 183  * General common environment variables shared on all AMCC eval boards
 184  */
 185 #define CONFIG_AMCC_DEF_ENV                                             \
 186         "netdev=" __stringify(CONFIG_USE_NETDEV) "\0"                           \
 187         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 188                 "nfsroot=${serverip}:${rootpath}\0"                     \
 189         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 190         "addip=setenv bootargs ${bootargs} "                            \
 191                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 192                 ":${hostname}:${netdev}:off panic=1\0"                  \
 193         "addtty=setenv bootargs ${bootargs}"                            \
 194                 " console=" __stringify(CONFIG_USE_TTY) ",${baudrate}\0"        \
 195         CONFIG_ADDMISC                                                  \
 196         "initrd_high=30000000\0"                                        \
 197         "kernel_addr_r=1000000\0"                                       \
 198         "fdt_addr_r=1800000\0"                                          \
 199         "ramdisk_addr_r=1900000\0"                                      \
 200         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                           \
 201         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"                    \
 202         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"              \
 203         CONFIG_AMCC_DEF_ENV_ROOTPATH
 204
 205 /*
 206  * Default environment for arch/powerpc booting
 207  * for boards that are ported to arch/powerpc
 208  */
 209 #define CONFIG_AMCC_DEF_ENV_POWERPC                                     \
 210         "flash_self=run ramargs addip addtty addmisc;"                  \
 211                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 212         "flash_nfs=run nfsargs addip addtty addmisc;"                   \
 213                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 214         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 215                 "tftp ${fdt_addr_r} ${fdt_file}; "                      \
 216                 "run nfsargs addip addtty addmisc;"                     \
 217                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 218         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
 219                 "tftp ${fdt_addr_r} ${fdt_file};"                       \
 220                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
 221         "net_self=run net_self_load;"                                   \
 222                 "run ramargs addip addtty addmisc;"                     \
 223                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0" \
 224         "fdt_file=" __stringify(CONFIG_HOSTNAME) "/" __stringify(CONFIG_HOSTNAME) ".dtb\0"
 225
 226 /*
 227  * Default environment for arch/ppc booting,
 228  * for boards that are not ported to arch/powerpc yet
 229  */
 230 #define CONFIG_AMCC_DEF_ENV_PPC                                         \
 231         "flash_self=run ramargs addip addtty addmisc;"                  \
 232                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 233         "flash_nfs=run nfsargs addip addtty addmisc;"                   \
 234                 "bootm ${kernel_addr}\0"                                \
 235         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 236                 "run nfsargs addip addtty addmisc;"                     \
 237                 "bootm ${kernel_addr_r}\0"
 238
 239 /*
 240  * Default environment for arch/ppc booting (old version),
 241  * for boards that are ported to arch/ppc and arch/powerpc
 242  */
 243 #define CONFIG_AMCC_DEF_ENV_PPC_OLD                                     \
 244         "flash_self_old=run ramargs addip addtty addmisc;"              \
 245                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 246         "flash_nfs_old=run nfsargs addip addtty addmisc;"               \
 247                 "bootm ${kernel_addr}\0"                                \
 248         "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};"                \
 249                 "run nfsargs addip addtty addmisc;"                     \
 250                 "bootm ${kernel_addr_r}\0"
 251
 252 #define CONFIG_AMCC_DEF_ENV_NOR_UPD                                     \
 253         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
 254         "load=tftp 200000 ${u-boot}\0"                                  \
 255         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;" \
 256                 "era " __stringify(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;"        \
 257                 "cp.b ${fileaddr} " __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
 258         "upd=run load update\0"                                         \
 259
 260 #endif /* __AMCC_COMMON_H */