include/configs/aria.h

   1 /*
   2  * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
   3  * (C) Copyright 2009, DAVE Srl <www.dave.eu>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * Aria board configuration file
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 #define CONFIG_ARIA 1
  16 /*
  17  * Memory map for the ARIA board:
  18  *
  19  * 0x0000_0000-0x0FFF_FFFF      DDR RAM (256 MB)
  20  * 0x3000_0000-0x3001_FFFF      On Chip SRAM (128 KB)
  21  * 0x3010_0000-0x3011_FFFF      On Board SRAM (128 KB) - CS6
  22  * 0x3020_0000-0x3021_FFFF      FPGA (128 KB) - CS2
  23  * 0x8000_0000-0x803F_FFFF      IMMR (4 MB)
  24  * 0x8400_0000-0x82FF_FFFF      PCI I/O space (16 MB)
  25  * 0xA000_0000-0xAFFF_FFFF      PCI memory space (256 MB)
  26  * 0xB000_0000-0xBFFF_FFFF      PCI memory mapped I/O space (256 MB)
  27  * 0xFC00_0000-0xFFFF_FFFF      NOR Boot FLASH (64 MB)
  28  */
  29
  30 /*
  31  * High Level Configuration Options
  32  */
  33 #define CONFIG_E300             1       /* E300 Family */
  34 #define CONFIG_FSL_DIU_FB       1       /* FSL DIU */
  35
  36 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  37
  38 /* video */
  39 #undef CONFIG_VIDEO
  40
  41 #if defined(CONFIG_VIDEO)
  42 #define CONFIG_CFB_CONSOLE
  43 #define CONFIG_VGA_AS_SINGLE_DEVICE
  44 #endif
  45
  46 /* CONFIG_PCI is defined at config time */
  47
  48 #define CONFIG_SYS_MPC512X_CLKIN        33000000        /* in Hz */
  49
  50 #define CONFIG_MISC_INIT_R
  51
  52 #define CONFIG_SYS_IMMR                 0x80000000
  53 #define CONFIG_SYS_DIU_ADDR             (CONFIG_SYS_IMMR+0x2100)
  54
  55 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  56 #define CONFIG_SYS_MEMTEST_END          0x00400000
  57
  58 /*
  59  * DDR Setup - manually set all parameters as there's no SPD etc.
  60  */
  61 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  62 #define CONFIG_SYS_DDR_BASE             0x00000000
  63 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  64 #define CONFIG_SYS_MAX_RAM_SIZE         0x20000000
  65
  66 #define CONFIG_SYS_IOCTRL_MUX_DDR       0x00000036
  67
  68 /* DDR Controller Configuration
  69  *
  70  * SYS_CFG:
  71  *      [31:31] MDDRC Soft Reset:       Diabled
  72  *      [30:30] DRAM CKE pin:           Enabled
  73  *      [29:29] DRAM CLK:               Enabled
  74  *      [28:28] Command Mode:           Enabled (For initialization only)
  75  *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
  76  *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
  77  *      [20:19] Read Test:              DON'T USE
  78  *      [18:18] Self Refresh:           Enabled
  79  *      [17:17] 16bit Mode:             Disabled
  80  *      [16:13] Ready Delay:            2
  81  *      [12:12] Half DQS Delay:         Disabled
  82  *      [11:11] Quarter DQS Delay:      Disabled
  83  *      [10:08] Write Delay:            2
  84  *      [07:07] Early ODT:              Disabled
  85  *      [06:06] On DIE Termination:     Disabled
  86  *      [05:05] FIFO Overflow Clear:    DON'T USE here
  87  *      [04:04] FIFO Underflow Clear:   DON'T USE here
  88  *      [03:03] FIFO Overflow Pending:  DON'T USE here
  89  *      [02:02] FIFO Underlfow Pending: DON'T USE here
  90  *      [01:01] FIFO Overlfow Enabled:  Enabled
  91  *      [00:00] FIFO Underflow Enabled: Enabled
  92  * TIME_CFG0
  93  *      [31:16] DRAM Refresh Time:      0 CSB clocks
  94  *      [15:8]  DRAM Command Time:      0 CSB clocks
  95  *      [07:00] DRAM Precharge Time:    0 CSB clocks
  96  * TIME_CFG1
  97  *      [31:26] DRAM tRFC:
  98  *      [25:21] DRAM tWR1:
  99  *      [20:17] DRAM tWRT1:
 100  *      [16:11] DRAM tDRR:
 101  *      [10:05] DRAM tRC:
 102  *      [04:00] DRAM tRAS:
 103  * TIME_CFG2
 104  *      [31:28] DRAM tRCD:
 105  *      [27:23] DRAM tFAW:
 106  *      [22:19] DRAM tRTW1:
 107  *      [18:15] DRAM tCCD:
 108  *      [14:10] DRAM tRTP:
 109  *      [09:05] DRAM tRP:
 110  *      [04:00] DRAM tRPA
 111  */
 112 #define CONFIG_SYS_MDDRC_SYS_CFG     (  (1 << 31) |     /* RST_B */ \
 113                                         (1 << 30) |     /* CKE */ \
 114                                         (1 << 29) |     /* CLK_ON */ \
 115                                         (0 << 28) |     /* CMD_MODE */ \
 116                                         (4 << 25) |     /* DRAM_ROW_SELECT */ \
 117                                         (3 << 21) |     /* DRAM_BANK_SELECT */ \
 118                                         (0 << 18) |     /* SELF_REF_EN */ \
 119                                         (0 << 17) |     /* 16BIT_MODE */ \
 120                                         (2 << 13) |     /* RDLY */ \
 121                                         (0 << 12) |     /* HALF_DQS_DLY */ \
 122                                         (1 << 11) |     /* QUART_DQS_DLY */ \
 123                                         (2 <<  8) |     /* WDLY */ \
 124                                         (0 <<  7) |     /* EARLY_ODT */ \
 125                                         (1 <<  6) |     /* ON_DIE_TERMINATE */ \
 126                                         (0 <<  5) |     /* FIFO_OV_CLEAR */ \
 127                                         (0 <<  4) |     /* FIFO_UV_CLEAR */ \
 128                                         (0 <<  1) |     /* FIFO_OV_EN */ \
 129                                         (0 <<  0)       /* FIFO_UV_EN */ \
 130                                      )
 131
 132 #define CONFIG_SYS_MDDRC_TIME_CFG0      0x030C3D2E
 133 #define CONFIG_SYS_MDDRC_TIME_CFG1      0x55D81189
 134 #define CONFIG_SYS_MDDRC_TIME_CFG2      0x34790863
 135
 136 #define CONFIG_SYS_DDRCMD_NOP           0x01380000
 137 #define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
 138 #define CONFIG_SYS_MICRON_EMR        (  (1 << 24) |     /* CMD_REQ */ \
 139                                         (0 << 22) |     /* DRAM_CS */ \
 140                                         (0 << 21) |     /* DRAM_RAS */ \
 141                                         (0 << 20) |     /* DRAM_CAS */ \
 142                                         (0 << 19) |     /* DRAM_WEB */ \
 143                                         (1 << 16) |     /* DRAM_BS[2:0] */ \
 144                                         (0 << 15) |     /* */ \
 145                                         (0 << 12) |     /* A12->out */ \
 146                                         (0 << 11) |     /* A11->RDQS */ \
 147                                         (0 << 10) |     /* A10->DQS# */ \
 148                                         (0 <<  7) |     /* OCD program */ \
 149                                         (0 <<  6) |     /* Rtt1 */ \
 150                                         (0 <<  3) |     /* posted CAS# */ \
 151                                         (0 <<  2) |     /* Rtt0 */ \
 152                                         (1 <<  1) |     /* ODS */ \
 153                                         (0 <<  0)       /* DLL */ \
 154                                      )
 155 #define CONFIG_SYS_MICRON_EMR2          0x01020000
 156 #define CONFIG_SYS_MICRON_EMR3          0x01030000
 157 #define CONFIG_SYS_DDRCMD_RFSH          0x01080000
 158 #define CONFIG_SYS_MICRON_INIT_DEV_OP   0x01000432
 159 #define CONFIG_SYS_MICRON_EMR_OCD    (  (1 << 24) |     /* CMD_REQ */ \
 160                                         (0 << 22) |     /* DRAM_CS */ \
 161                                         (0 << 21) |     /* DRAM_RAS */ \
 162                                         (0 << 20) |     /* DRAM_CAS */ \
 163                                         (0 << 19) |     /* DRAM_WEB */ \
 164                                         (1 << 16) |     /* DRAM_BS[2:0] */ \
 165                                         (0 << 15) |     /* */ \
 166                                         (0 << 12) |     /* A12->out */ \
 167                                         (0 << 11) |     /* A11->RDQS */ \
 168                                         (1 << 10) |     /* A10->DQS# */ \
 169                                         (7 <<  7) |     /* OCD program */ \
 170                                         (0 <<  6) |     /* Rtt1 */ \
 171                                         (0 <<  3) |     /* posted CAS# */ \
 172                                         (1 <<  2) |     /* Rtt0 */ \
 173                                         (0 <<  1) |     /* ODS (Output Drive Strength) */ \
 174                                         (0 <<  0)       /* DLL */ \
 175                                      )
 176
 177 /*
 178  * Backward compatible definitions,
 179  * so we do not have to change arch/powerpc/cpu/mpc512x/fixed_sdram.c
 180  */
 181 #define CONFIG_SYS_DDRCMD_EM2           (CONFIG_SYS_MICRON_EMR2)
 182 #define CONFIG_SYS_DDRCMD_EM3           (CONFIG_SYS_MICRON_EMR3)
 183 #define CONFIG_SYS_DDRCMD_EN_DLL        (CONFIG_SYS_MICRON_EMR)
 184 #define CONFIG_SYS_DDRCMD_OCD_DEFAULT   (CONFIG_SYS_MICRON_EMR_OCD)
 185
 186 /* DDR Priority Manager Configuration */
 187 #define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
 188 #define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
 189 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
 190 #define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
 191 #define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
 192 #define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
 193 #define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
 194 #define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
 195 #define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
 196 #define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
 197 #define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
 198 #define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
 199 #define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
 200 #define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
 201 #define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
 202 #define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
 203 #define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
 204 #define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
 205 #define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
 206 #define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
 207 #define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
 208 #define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
 209 #define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111
 210
 211 /*
 212  * NOR FLASH on the Local Bus
 213  */
 214 #define CONFIG_SYS_FLASH_CFI                            /* use the CFI code */
 215 #define CONFIG_FLASH_CFI_DRIVER                         /* use the CFI driver */
 216 #define CONFIG_SYS_FLASH_BASE           0xF8000000      /* start of FLASH */
 217 #define CONFIG_SYS_FLASH_SIZE           0x08000000      /* max flash size */
 218
 219 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 220 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* number of banks */
 221 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
 222 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* max sectors */
 223
 224 #undef CONFIG_SYS_FLASH_CHECKSUM
 225
 226 /*
 227  * NAND FLASH support
 228  * drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only)
 229  */
 230 #define CONFIG_CMD_NAND                                 /* enable NAND support */
 231 #define CONFIG_JFFS2_NAND                               /* with JFFS2 on it */
 232 #define CONFIG_NAND_MPC5121_NFC
 233 #define CONFIG_SYS_NAND_BASE            0x40000000
 234 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 235
 236 /*
 237  * Configuration parameters for MPC5121 NAND driver
 238  */
 239 #define CONFIG_FSL_NFC_WIDTH            1
 240 #define CONFIG_FSL_NFC_WRITE_SIZE       2048
 241 #define CONFIG_FSL_NFC_SPARE_SIZE       64
 242 #define CONFIG_FSL_NFC_CHIPS            CONFIG_SYS_MAX_NAND_DEVICE
 243
 244 #define CONFIG_SYS_SRAM_BASE            0x30000000
 245 #define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */
 246
 247 /* Make two SRAM regions contiguous */
 248 #define CONFIG_SYS_ARIA_SRAM_BASE       (CONFIG_SYS_SRAM_BASE + \
 249                                          CONFIG_SYS_SRAM_SIZE)
 250 #define CONFIG_SYS_ARIA_SRAM_SIZE       0x00100000      /* reserve 1MB-window */
 251 #define CONFIG_SYS_CS6_START            CONFIG_SYS_ARIA_SRAM_BASE
 252 #define CONFIG_SYS_CS6_SIZE             CONFIG_SYS_ARIA_SRAM_SIZE
 253
 254 #define CONFIG_SYS_ARIA_FPGA_BASE       (CONFIG_SYS_ARIA_SRAM_BASE + \
 255                                          CONFIG_SYS_ARIA_SRAM_SIZE)
 256 #define CONFIG_SYS_ARIA_FPGA_SIZE       0x20000         /* 128 KB */
 257
 258 #define CONFIG_SYS_CS2_START            CONFIG_SYS_ARIA_FPGA_BASE
 259 #define CONFIG_SYS_CS2_SIZE             CONFIG_SYS_ARIA_FPGA_SIZE
 260
 261 #define CONFIG_SYS_CS0_CFG              0x05059150
 262 #define CONFIG_SYS_CS2_CFG              (       (5 << 24) | \
 263                                                 (5 << 16) | \
 264                                                 (1 << 15) | \
 265                                                 (0 << 14) | \
 266                                                 (0 << 13) | \
 267                                                 (1 << 12) | \
 268                                                 (0 << 10) | \
 269                                                 (3 <<  8) | /* 32 bit */ \
 270                                                 (0 <<  7) | \
 271                                                 (1 <<  6) | \
 272                                                 (1 <<  4) | \
 273                                                 (0 <<  3) | \
 274                                                 (0 <<  2) | \
 275                                                 (0 <<  1) | \
 276                                                 (0 <<  0)   \
 277                                         )
 278 #define CONFIG_SYS_CS6_CFG              0x05059150
 279
 280 /* Use alternative CS timing for CS0 and CS2 */
 281 #define CONFIG_SYS_CS_ALETIMING 0x00000005
 282
 283 /* Use SRAM for initial stack */
 284 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE
 285 #define CONFIG_SYS_INIT_RAM_SIZE                CONFIG_SYS_SRAM_SIZE
 286
 287 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 288                                          GENERATED_GBL_DATA_SIZE)
 289 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 290
 291 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 292 #define CONFIG_SYS_MONITOR_LEN          (384 * 1024)
 293
 294 #ifdef  CONFIG_FSL_DIU_FB
 295 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)
 296 #else
 297 #define CONFIG_SYS_MALLOC_LEN           (512 * 1024)
 298 #endif
 299
 300 /* FPGA */
 301 #define CONFIG_ARIA_FPGA                1
 302
 303 /*
 304  * Serial Port
 305  */
 306 #define CONFIG_CONS_INDEX               1
 307
 308 /*
 309  * Serial console configuration
 310  */
 311 #define CONFIG_PSC_CONSOLE              3       /* console on PSC3 */
 312 #define CONFIG_SYS_PSC3
 313 #if CONFIG_PSC_CONSOLE != 3
 314 #error CONFIG_PSC_CONSOLE must be 3
 315 #endif
 316
 317 #define CONFIG_BAUDRATE                 115200  /* ... at 115200 bps */
 318 #define CONFIG_SYS_BAUDRATE_TABLE  \
 319         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 320
 321 #define CONSOLE_FIFO_TX_SIZE            FIFOC_PSC3_TX_SIZE
 322 #define CONSOLE_FIFO_TX_ADDR            FIFOC_PSC3_TX_ADDR
 323 #define CONSOLE_FIFO_RX_SIZE            FIFOC_PSC3_RX_SIZE
 324 #define CONSOLE_FIFO_RX_ADDR            FIFOC_PSC3_RX_ADDR
 325
 326 #define CONFIG_CMDLINE_EDITING          1       /* command line history */
 327 /* Use the HUSH parser */
 328 #define CONFIG_SYS_HUSH_PARSER
 329 #ifdef  CONFIG_SYS_HUSH_PARSER
 330 #endif
 331
 332 /*
 333  * PCI
 334  */
 335 #ifdef CONFIG_PCI
 336 #define CONFIG_PCI_INDIRECT_BRIDGE
 337
 338 #define CONFIG_SYS_PCI_MEM_BASE         0xA0000000
 339 #define CONFIG_SYS_PCI_MEM_PHYS         CONFIG_SYS_PCI_MEM_BASE
 340 #define CONFIG_SYS_PCI_MEM_SIZE         0x10000000      /* 256M */
 341 #define CONFIG_SYS_PCI_MMIO_BASE        (CONFIG_SYS_PCI_MEM_BASE + \
 342                                          CONFIG_SYS_PCI_MEM_SIZE)
 343 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 344 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000      /* 256M */
 345 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 346 #define CONFIG_SYS_PCI_IO_PHYS          0x84000000
 347 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000      /* 16M */
 348
 349 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 350
 351 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 352
 353 #endif
 354
 355 /* I2C */
 356 #define CONFIG_HARD_I2C                 /* I2C with hardware support */
 357 #define CONFIG_I2C_MULTI_BUS
 358
 359 /* I2C speed and slave address */
 360 #define CONFIG_SYS_I2C_SPEED            100000
 361 #define CONFIG_SYS_I2C_SLAVE            0x7F
 362 #if 0
 363 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}}      /* Don't probe these addrs */
 364 #endif
 365
 366 /*
 367  * IIM - IC Identification Module
 368  */
 369 #undef CONFIG_FSL_IIM
 370
 371 /*
 372  * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
 373  * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
 374  */
 375 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
 376 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
 377 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10
 378 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       5
 379
 380 /*
 381  * Ethernet configuration
 382  */
 383 #define CONFIG_MPC512x_FEC              1
 384 #define CONFIG_PHY_ADDR                 0x17
 385 #define CONFIG_MII                      1       /* MII PHY management */
 386 #define CONFIG_FEC_AN_TIMEOUT           1
 387 #define CONFIG_HAS_ETH0
 388
 389 /*
 390  * Environment
 391  */
 392 #define CONFIG_ENV_IS_IN_FLASH  1
 393 /* This has to be a multiple of the flash sector size */
 394 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_MONITOR_BASE + \
 395                                          CONFIG_SYS_MONITOR_LEN)
 396 #define CONFIG_ENV_SIZE                 0x2000
 397 #define CONFIG_ENV_SECT_SIZE            0x20000 /* one sector (256K) */
 398
 399 /* Address and size of Redundant Environment Sector     */
 400 #define CONFIG_ENV_ADDR_REDUND          (CONFIG_ENV_ADDR + \
 401                                          CONFIG_ENV_SECT_SIZE)
 402 #define CONFIG_ENV_SIZE_REDUND          (CONFIG_ENV_SIZE)
 403
 404 #define CONFIG_LOADS_ECHO               1
 405 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1
 406
 407 #include <config_cmd_default.h>
 408
 409 #define CONFIG_CMD_ASKENV
 410 #define CONFIG_CMD_DHCP
 411 #define CONFIG_CMD_EEPROM
 412 #undef CONFIG_CMD_FUSE
 413 #define CONFIG_CMD_I2C
 414 #undef CONFIG_CMD_IDE
 415 #define CONFIG_CMD_JFFS2
 416 #define CONFIG_CMD_MII
 417 #define CONFIG_CMD_NFS
 418 #define CONFIG_CMD_PING
 419 #define CONFIG_CMD_REGINFO
 420
 421 #if defined(CONFIG_PCI)
 422 #define CONFIG_CMD_PCI
 423 #endif
 424
 425 #if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2)
 426 #define CONFIG_DOS_PARTITION
 427 #define CONFIG_MAC_PARTITION
 428 #define CONFIG_ISO_PARTITION
 429 #endif /* defined(CONFIG_CMD_IDE) */
 430
 431 /*
 432  * Dynamic MTD partition support
 433  */
 434 #define CONFIG_CMD_MTDPARTS
 435 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 436 #define CONFIG_FLASH_CFI_MTD
 437 #define MTDIDS_DEFAULT          "nor0=f8000000.flash,nand0=mpc5121.nand"
 438
 439 /*
 440  * NOR flash layout:
 441  *
 442  * F8000000 - FEAFFFFF  107 MiB         User Data
 443  * FEB00000 - FFAFFFFF   16 MiB         Root File System
 444  * FFB00000 - FFFEFFFF    4 MiB         Linux Kernel
 445  * FFF00000 - FFFBFFFF  768 KiB         U-Boot (up to 512 KiB) and 2 x * env
 446  * FFFC0000 - FFFFFFFF  256 KiB         Device Tree
 447  *
 448  * NAND flash layout: one big partition
 449  */
 450 #define MTDPARTS_DEFAULT        "mtdparts=f8000000.flash:107m(user),"   \
 451                                                 "16m(rootfs),"          \
 452                                                 "4m(kernel),"           \
 453                                                 "768k(u-boot),"         \
 454                                                 "256k(dtb);"            \
 455                                         "mpc5121.nand:-(data)"
 456
 457 /*
 458  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
 459  * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE
 460  * is set to 0xFFFF, watchdog timeouts after about 64s. For details
 461  * refer to chapter 36 of the MPC5121e Reference Manual.
 462  */
 463 /* #define CONFIG_WATCHDOG */           /* enable watchdog */
 464 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
 465
 466  /*
 467  * Miscellaneous configurable options
 468  */
 469 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 470 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 471
 472 #ifdef CONFIG_CMD_KGDB
 473 # define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
 474 #else
 475 # define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
 476 #endif
 477
 478 /* Print Buffer Size */
 479 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 480                                  sizeof(CONFIG_SYS_PROMPT) + 16)
 481 /* max number of command args */
 482 #define CONFIG_SYS_MAXARGS      32
 483 /* Boot Argument Buffer Size */
 484 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 485
 486 /*
 487  * For booting Linux, the board info and command line data
 488  * have to be in the first 256 MB of memory, since this is
 489  * the maximum mapped by the Linux kernel during initialization.
 490  */
 491 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)
 492
 493 /* Cache Configuration */
 494 #define CONFIG_SYS_DCACHE_SIZE          32768
 495 #define CONFIG_SYS_CACHELINE_SIZE       32
 496 #ifdef CONFIG_CMD_KGDB
 497 #define CONFIG_SYS_CACHELINE_SHIFT      5       /* log base 2 of 32 */
 498 #endif
 499
 500 #define CONFIG_SYS_HID0_INIT            0x000000000
 501 #define CONFIG_SYS_HID0_FINAL           (HID0_ENABLE_MACHINE_CHECK | \
 502                                          HID0_ICE)
 503 #define CONFIG_SYS_HID2 HID2_HBE
 504
 505 #define CONFIG_HIGH_BATS                1       /* High BATs supported */
 506
 507 #ifdef CONFIG_CMD_KGDB
 508 #define CONFIG_KGDB_BAUDRATE            230400  /* speed of kgdb serial port */
 509 #endif
 510
 511 /*
 512  * Environment Configuration
 513  */
 514 #define CONFIG_ENV_OVERWRITE
 515 #define CONFIG_TIMESTAMP
 516
 517 #define CONFIG_HOSTNAME                 aria
 518 #define CONFIG_BOOTFILE                 "aria/uImage"
 519 #define CONFIG_ROOTPATH                 "/opt/eldk/ppc_6xx"
 520
 521 #define CONFIG_LOADADDR                 400000  /* default load addr */
 522
 523 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
 524 #undef  CONFIG_BOOTARGS                 /* the boot command will set bootargs */
 525
 526 #define CONFIG_BAUDRATE         115200
 527
 528 #define CONFIG_PREBOOT  "echo;" \
 529         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 530         "echo"
 531
 532 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 533         "u-boot_addr_r=200000\0"                                        \
 534         "kernel_addr_r=600000\0"                                        \
 535         "fdt_addr_r=880000\0"                                           \
 536         "ramdisk_addr_r=900000\0"                                       \
 537         "u-boot_addr=FFF00000\0"                                        \
 538         "kernel_addr=FFB00000\0"                                        \
 539         "fdt_addr=FFFC0000\0"                                           \
 540         "ramdisk_addr=FEB00000\0"                                       \
 541         "ramdiskfile=aria/uRamdisk\0"                           \
 542         "u-boot=aria/u-boot.bin\0"                                      \
 543         "fdtfile=aria/aria.dtb\0"                                       \
 544         "netdev=eth0\0"                                                 \
 545         "consdev=ttyPSC0\0"                                             \
 546         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 547                 "nfsroot=${serverip}:${rootpath}\0"                     \
 548         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 549         "addip=setenv bootargs ${bootargs} "                            \
 550                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 551                 ":${hostname}:${netdev}:off panic=1\0"                  \
 552         "addtty=setenv bootargs ${bootargs} "                           \
 553                 "console=${consdev},${baudrate}\0"                      \
 554         "flash_nfs=run nfsargs addip addtty;"                           \
 555                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 556         "flash_self=run ramargs addip addtty;"                          \
 557                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 558         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 559                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 560                 "run nfsargs addip addtty;"                             \
 561                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 562         "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
 563                 "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
 564                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 565                 "run ramargs addip addtty;"                             \
 566                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
 567         "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
 568         "update=protect off ${u-boot_addr} +${filesize};"               \
 569                 "era ${u-boot_addr} +${filesize};"                      \
 570                 "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
 571         "upd=run load update\0"                                         \
 572         ""
 573
 574 #define CONFIG_BOOTCOMMAND      "run flash_self"
 575
 576 #define CONFIG_OF_LIBFDT        1
 577 #define CONFIG_OF_BOARD_SETUP   1
 578 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES      1
 579
 580 #define OF_CPU                  "PowerPC,5121@0"
 581 #define OF_SOC_COMPAT           "fsl,mpc5121-immr"
 582 #define OF_TBCLK                (bd->bi_busfreq / 4)
 583 #define OF_STDOUT_PATH          "/soc@80000000/serial@11300"
 584
 585 /*-----------------------------------------------------------------------
 586  * IDE/ATA stuff
 587  *-----------------------------------------------------------------------
 588  */
 589
 590 #undef  CONFIG_IDE_8xx_PCCARD           /* Use IDE with PC Card Adapter */
 591 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 592 #undef  CONFIG_IDE_LED                  /* LED   for IDE not supported  */
 593
 594 #define CONFIG_IDE_RESET                /* reset for IDE supported      */
 595 #define CONFIG_IDE_PREINIT
 596
 597 #define CONFIG_SYS_IDE_MAXBUS           1       /* 1 IDE bus            */
 598 #define CONFIG_SYS_IDE_MAXDEVICE        2       /* 1 drive per IDE bus  */
 599
 600 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 601 #define CONFIG_SYS_ATA_BASE_ADDR        get_pata_base()
 602
 603 /* Offset for data I/O                  RefMan MPC5121EE Table 28-10    */
 604 #define CONFIG_SYS_ATA_DATA_OFFSET      (0x00A0)
 605
 606 /* Offset for normal register accesses  */
 607 #define CONFIG_SYS_ATA_REG_OFFSET       (CONFIG_SYS_ATA_DATA_OFFSET)
 608
 609 /* Offset for alternate registers       RefMan MPC5121EE Table 28-23    */
 610 #define CONFIG_SYS_ATA_ALT_OFFSET       (0x00D8)
 611
 612 /* Interval between registers   */
 613 #define CONFIG_SYS_ATA_STRIDE           4
 614
 615 #define ATA_BASE_ADDR                   get_pata_base()
 616
 617 /*
 618  * Control register bit definitions
 619  */
 620 #define FSL_ATA_CTRL_FIFO_RST_B         0x80000000
 621 #define FSL_ATA_CTRL_ATA_RST_B          0x40000000
 622 #define FSL_ATA_CTRL_FIFO_TX_EN         0x20000000
 623 #define FSL_ATA_CTRL_FIFO_RCV_EN        0x10000000
 624 #define FSL_ATA_CTRL_DMA_PENDING        0x08000000
 625 #define FSL_ATA_CTRL_DMA_ULTRA          0x04000000
 626 #define FSL_ATA_CTRL_DMA_WRITE          0x02000000
 627 #define FSL_ATA_CTRL_IORDY_EN           0x01000000
 628
 629 /* Clocks in use */
 630 #define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |                           \
 631                          CLOCK_SCCR1_LPC_EN |                           \
 632                          CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) |       \
 633                          CLOCK_SCCR1_PSCFIFO_EN |                       \
 634                          CLOCK_SCCR1_DDR_EN |                           \
 635                          CLOCK_SCCR1_FEC_EN |                           \
 636                          CLOCK_SCCR1_NFC_EN |                           \
 637                          CLOCK_SCCR1_PATA_EN |                          \
 638                          CLOCK_SCCR1_PCI_EN |                           \
 639                          CLOCK_SCCR1_TPR_EN)
 640
 641 #define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN |           \
 642                          CLOCK_SCCR2_SPDIF_EN |         \
 643                          CLOCK_SCCR2_DIU_EN |           \
 644                          CLOCK_SCCR2_I2C_EN)
 645
 646 #endif  /* __CONFIG_H */