include/configs/aristainetos-common.h

   1 /*
   2  * (C) Copyright 2015
   3  * (C) Copyright 2014
   4  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   8  *
   9  * Configuration settings for the Freescale i.MX6Q SabreSD board.
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13 #ifndef __ARISTAINETOS_COMMON_CONFIG_H
  14 #define __ARISTAINETOS_COMMON_CONFIG_H
  15
  16 #define CONFIG_MX6
  17
  18 #include "mx6_common.h"
  19 #include <linux/sizes.h>
  20
  21 #define CONFIG_DISPLAY_CPUINFO
  22 #define CONFIG_DISPLAY_BOARDINFO
  23
  24 #include <asm/arch/imx-regs.h>
  25 #include <asm/imx-common/gpio.h>
  26
  27 #define CONFIG_MACH_TYPE        4501
  28 #define CONFIG_MMCROOT          "/dev/mmcblk0p1"
  29 #define PHYS_SDRAM_SIZE         (1u * 1024 * 1024 * 1024)
  30
  31 #define CONFIG_SYS_GENERIC_BOARD
  32
  33 /* Size of malloc() pool */
  34 #define CONFIG_SYS_MALLOC_LEN           (64 * SZ_1M)
  35
  36 #define CONFIG_BOARD_EARLY_INIT_F
  37 #define CONFIG_MXC_GPIO
  38
  39 #define CONFIG_MXC_UART
  40
  41 #define CONFIG_CMD_FUSE
  42 #define CONFIG_MXC_OCOTP
  43
  44 /* MMC Configs */
  45 #define CONFIG_FSL_ESDHC
  46 #define CONFIG_FSL_USDHC
  47 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  48
  49 #define CONFIG_MMC
  50 #define CONFIG_CMD_MMC
  51 #define CONFIG_GENERIC_MMC
  52 #define CONFIG_BOUNCE_BUFFER
  53 #define CONFIG_CMD_EXT2
  54 #define CONFIG_CMD_FAT
  55 #define CONFIG_DOS_PARTITION
  56
  57 #define CONFIG_CMD_PING
  58 #define CONFIG_CMD_DHCP
  59 #define CONFIG_CMD_MII
  60 #define CONFIG_CMD_NET
  61 #define CONFIG_FEC_MXC
  62 #define CONFIG_MII
  63 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  64 #define CONFIG_ETHPRIME                 "FEC"
  65 #define CONFIG_FEC_MXC_PHYADDR          0
  66
  67 #define CONFIG_PHYLIB
  68 #define CONFIG_PHY_MICREL
  69
  70 #define CONFIG_CMD_SF
  71 #define CONFIG_SPI_FLASH
  72 #define CONFIG_SPI_FLASH_MTD
  73 #define CONFIG_SPI_FLASH_STMICRO
  74 #define CONFIG_MXC_SPI
  75 #define CONFIG_SF_DEFAULT_BUS           3
  76 #define CONFIG_SF_DEFAULT_SPEED         20000000
  77 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  78 #define CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
  79
  80 /* allow to overwrite serial and ethaddr */
  81 #define CONFIG_ENV_OVERWRITE
  82 #define CONFIG_CONS_INDEX               1
  83 #define CONFIG_BAUDRATE                 115200
  84
  85 /* Command definition */
  86 #include <config_cmd_default.h>
  87
  88 #define CONFIG_CMD_BMODE
  89 #define CONFIG_CMD_BOOTZ
  90 #define CONFIG_CMD_SETEXPR
  91 #undef CONFIG_CMD_IMLS
  92
  93 #define CONFIG_BOOTDELAY                3
  94
  95 #define CONFIG_LOADADDR                 0x12000000
  96 #define CONFIG_SYS_TEXT_BASE            0x17800000
  97
  98 #define CONFIG_EXTRA_ENV_SETTINGS \
  99         "script=u-boot.scr\0" \
 100         "fit_file=/boot/system.itb\0" \
 101         "loadaddr=0x12000000\0" \
 102         "fit_addr_r=0x14000000\0" \
 103         "uboot=/boot/u-boot.imx\0" \
 104         "uboot_sz=d0000\0" \
 105         "rescue_sys_addr=f0000\0" \
 106         "rescue_sys_length=f10000\0" \
 107         "panel=lb07wv8\0" \
 108         "splashpos=m,m\0" \
 109         "console=" CONFIG_CONSOLE_DEV "\0" \
 110         "fdt_high=0xffffffff\0"   \
 111         "initrd_high=0xffffffff\0" \
 112         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
 113         "set_fit_default=fdt addr ${fit_addr_r};fdt set /configurations " \
 114                 "default ${board_type}\0" \
 115         "get_env=mw ${loadaddr} 0 0x20000;" \
 116                 "mmc rescan;" \
 117                 "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} env.txt;" \
 118                 "env import -t ${loadaddr}\0" \
 119         "default_env=mw ${loadaddr} 0 0x20000;" \
 120                 "env export -t ${loadaddr} serial# ethaddr eth1addr " \
 121                 "board_type panel;" \
 122                 "env default -a;" \
 123                 "env import -t ${loadaddr}\0" \
 124         "loadbootscript=" \
 125                 "ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 126         "bootscript=echo Running bootscript from mmc ...; " \
 127                 "source\0" \
 128         "mmcpart=1\0" \
 129         "mmcdev=0\0" \
 130         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 131         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 132                 "root=${mmcroot}\0" \
 133         "mmcboot=echo Booting from mmc ...; " \
 134                 "run mmcargs addmtd addmisc set_fit_default;" \
 135                 "bootm ${fit_addr_r}\0" \
 136         "mmc_load_fit=ext2load mmc ${mmcdev}:${mmcpart} ${fit_addr_r} " \
 137                 "${fit_file}\0" \
 138         "mmc_load_uboot=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
 139                 "${uboot}\0" \
 140         "mmc_upd_uboot=mw.b ${loadaddr} 0xff ${uboot_sz};" \
 141                 "setexpr cmp_buf ${loadaddr} + ${uboot_sz};" \
 142                 "setexpr uboot_maxsize ${uboot_sz} - 400;" \
 143                 "mw.b ${cmp_buf} 0x00 ${uboot_sz};" \
 144                 "run mmc_load_uboot;sf probe;sf erase 0 ${uboot_sz};" \
 145                 "sf write ${loadaddr} 400 ${filesize};" \
 146                 "sf read ${cmp_buf} 400 ${uboot_sz};" \
 147                 "cmp.b ${loadaddr} ${cmp_buf} ${uboot_maxsize}\0" \
 148         "ubiboot=echo Booting from ubi ...; " \
 149                 "run ubiargs addmtd addmisc set_fit_default;" \
 150                 "bootm ${fit_addr_r}\0" \
 151         "ubifs_load_fit=sf probe;ubi part ubi 2048;ubifsmount ubi:rootfs;" \
 152                 "ubifsload ${fit_addr_r} /boot/system.itb; " \
 153                 "imi ${fit_addr_r}\0 " \
 154         "rescueargs=setenv bootargs console=${console},${baudrate} " \
 155                 "root=/dev/ram rw\0 " \
 156         "rescueboot=echo Booting rescue system from NOR ...; " \
 157                 "run rescueargs addmtd addmisc set_fit_default;" \
 158                 "bootm ${fit_addr_r}\0" \
 159         "rescue_load_fit=sf probe;sf read ${fit_addr_r} ${rescue_sys_addr} " \
 160                 "${rescue_sys_length}; imi ${fit_addr_r}\0" \
 161         CONFIG_EXTRA_ENV_BOARD_SETTINGS
 162
 163 #define CONFIG_BOOTCOMMAND \
 164         "mmc dev ${mmcdev};" \
 165         "if mmc rescan; then " \
 166                 "if run loadbootscript; then " \
 167                         "run bootscript; " \
 168                 "else " \
 169                         "if run mmc_load_fit; then " \
 170                                 "run mmcboot; " \
 171                         "else " \
 172                                 "if run ubifs_load_fit; then " \
 173                                         "run ubiboot; " \
 174                                 "else " \
 175                                         "if run rescue_load_fit; then " \
 176                                                 "run rescueboot; " \
 177                                         "else " \
 178                                                 "echo RESCUE SYSTEM BOOT " \
 179                                                         "FAILURE;" \
 180                                         "fi; " \
 181                                 "fi; " \
 182                         "fi; " \
 183                 "fi; " \
 184         "else " \
 185                 "if run ubifs_load_fit; then " \
 186                         "run ubiboot; " \
 187                 "else " \
 188                         "if run rescue_load_fit; then " \
 189                                 "run rescueboot; " \
 190                         "else " \
 191                                 "echo RESCUE SYSTEM BOOT FAILURE;" \
 192                         "fi; " \
 193                 "fi; " \
 194         "fi"
 195
 196 #define CONFIG_ARP_TIMEOUT              200UL
 197
 198 /* Miscellaneous configurable options */
 199 #define CONFIG_SYS_LONGHELP
 200 #define CONFIG_SYS_HUSH_PARSER
 201 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 202 #define CONFIG_AUTO_COMPLETE
 203 #define CONFIG_SYS_CBSIZE               256
 204
 205 /* Print Buffer Size */
 206 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 207 #define CONFIG_SYS_MAXARGS             16
 208 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 209
 210 #define CONFIG_SYS_MEMTEST_START        PHYS_SDRAM
 211 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 0x100000)
 212 #define CONFIG_SYS_MEMTEST_SCRATCH      0x10800000
 213
 214 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 215
 216 #define CONFIG_CMDLINE_EDITING
 217 #define CONFIG_STACKSIZE                (128 * 1024)
 218
 219 /* Physical Memory Map */
 220 #define CONFIG_NR_DRAM_BANKS            1
 221 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 222
 223 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 224 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 225 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 226
 227 #define CONFIG_SYS_INIT_SP_OFFSET \
 228         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 229 #define CONFIG_SYS_INIT_SP_ADDR \
 230         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 231
 232 /* FLASH and environment organization */
 233 #define CONFIG_SYS_NO_FLASH
 234
 235 #define CONFIG_ENV_SIZE                 (12 * 1024)
 236 #define CONFIG_ENV_IS_IN_SPI_FLASH
 237 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
 238 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 239 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 240 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 241 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 242 #define CONFIG_ENV_SECT_SIZE            (0x010000)
 243 #define CONFIG_ENV_OFFSET               (0x0d0000)
 244 #define CONFIG_ENV_OFFSET_REDUND        (0x0e0000)
 245
 246 #define CONFIG_OF_LIBFDT
 247
 248 #define CONFIG_CMD_CACHE
 249
 250 #define CONFIG_SYS_FSL_USDHC_NUM        2
 251
 252 /* I2C */
 253 #define CONFIG_CMD_I2C
 254 #define CONFIG_SYS_I2C
 255 #define CONFIG_SYS_I2C_MXC
 256 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
 257 #define CONFIG_SYS_I2C_SPEED            100000
 258 #define CONFIG_SYS_I2C_SLAVE            0x7f
 259 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x00} }
 260
 261 #define CONFIG_CMD_GPIO
 262
 263 /* NAND stuff */
 264 #define CONFIG_CMD_NAND
 265 #define CONFIG_CMD_NAND_TRIMFFS
 266 #define CONFIG_NAND_MXS
 267 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 268 #define CONFIG_SYS_NAND_BASE            0x40000000
 269 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 270 #define CONFIG_SYS_NAND_ONFI_DETECTION
 271
 272 /* DMA stuff, needed for GPMI/MXS NAND support */
 273 #define CONFIG_APBH_DMA
 274 #define CONFIG_APBH_DMA_BURST
 275 #define CONFIG_APBH_DMA_BURST8
 276
 277 /* RTC */
 278 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
 279 #define CONFIG_SYS_RTC_BUS_NUM  2
 280 #define CONFIG_RTC_M41T11
 281 #define CONFIG_CMD_DATE
 282
 283 /* USB Configs */
 284 #define CONFIG_CMD_USB
 285 #define CONFIG_CMD_FAT
 286 #define CONFIG_USB_EHCI
 287 #define CONFIG_USB_EHCI_MX6
 288 #define CONFIG_USB_STORAGE
 289 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 290 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 291 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 292 #define CONFIG_MXC_USB_FLAGS    0
 293
 294 /* UBI support */
 295 #define CONFIG_CMD_MTDPARTS
 296 #define CONFIG_MTD_PARTITIONS
 297 #define CONFIG_MTD_DEVICE
 298 #define CONFIG_RBTREE
 299 #define CONFIG_LZO
 300 #define CONFIG_CMD_UBI
 301 #define CONFIG_CMD_UBIFS
 302
 303 #define CONFIG_MTD_UBI_FASTMAP
 304 #define CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT      1
 305
 306 #define CONFIG_HW_WATCHDOG
 307 #define CONFIG_IMX_WATCHDOG
 308
 309 #define CONFIG_FIT
 310
 311 /* Framebuffer */
 312 #define CONFIG_VIDEO
 313 #define CONFIG_VIDEO_IPUV3
 314 /* check this console not needed, after test remove it */
 315 #define CONFIG_CFB_CONSOLE
 316 #define CONFIG_VGA_AS_SINGLE_DEVICE
 317 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 318 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 319 #define CONFIG_VIDEO_BMP_RLE8
 320 #define CONFIG_SPLASH_SCREEN
 321 #define CONFIG_SPLASH_SCREEN_ALIGN
 322 #define CONFIG_BMP_16BPP
 323 #define CONFIG_VIDEO_LOGO
 324 #define CONFIG_VIDEO_BMP_LOGO
 325 #define CONFIG_IPUV3_CLK 198000000
 326 #define CONFIG_IMX_VIDEO_SKIP
 327
 328 #define CONFIG_CMD_BMP
 329
 330 #define CONFIG_PWM_IMX
 331 #define CONFIG_IMX6_PWM_PER_CLK 66000000
 332
 333 #endif /* __ARISTAINETOS_COMMON_CONFIG_H */