include/configs/at91rm9200ek.h

   1 /*
   2  * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com>
   3  *
   4  * based on previous work by
   5  *
   6  * Ulf Samuelsson <ulf@atmel.com>
   7  * Rick Bronson <rick@efn.org>
   8  *
   9  * Configuration settings for the AT91RM9200EK board.
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #ifndef __AT91RM9200EK_CONFIG_H__
  15 #define __AT91RM9200EK_CONFIG_H__
  16
  17 #include <linux/sizes.h>
  18
  19 /*
  20  * set some initial configurations depending on configure target
  21  *
  22  * at91rm9200ek_config     -> boot from 0x0 in NOR Flash at CS0
  23  * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel
  24  *                            initialisation was done by some preloader
  25  */
  26 #ifdef CONFIG_RAMBOOT
  27 #define CONFIG_SKIP_LOWLEVEL_INIT
  28 #define CONFIG_SYS_TEXT_BASE 0x20100000
  29 #else
  30 #define CONFIG_SYS_TEXT_BASE 0x10000000
  31 #endif
  32
  33 /*
  34  * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz
  35  * AT91C_MAIN_CLOCK is the frequency of PLLA output
  36  * AT91C_MASTER_CLOCK is the peripherial clock
  37  * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely
  38  *  set in arch/arm/cpu/arm920t/at91/timer.c)
  39  * CONFIG_SYS_HZ is the tick rate for timer tc0
  40  */
  41 #define AT91C_XTAL_CLOCK                18432000
  42 #define CONFIG_SYS_AT91_SLOW_CLOCK      32768
  43 #define AT91C_MAIN_CLOCK                ((AT91C_XTAL_CLOCK / 4) * 39)
  44 #define AT91C_MASTER_CLOCK              (AT91C_MAIN_CLOCK / 3 )
  45 #define CONFIG_SYS_HZ_CLOCK             (AT91C_MASTER_CLOCK / 2)
  46
  47 /* CPU configuration */
  48 #define CONFIG_AT91RM9200
  49 #define CONFIG_AT91RM9200EK
  50 #define CONFIG_CPUAT91
  51 #define USE_920T_MMU
  52
  53 #include <asm/hardware.h>       /* needed for port definitions */
  54
  55 #define CONFIG_CMDLINE_TAG
  56 #define CONFIG_SETUP_MEMORY_TAGS
  57 #define CONFIG_INITRD_TAG
  58
  59 #define CONFIG_BOARD_EARLY_INIT_F
  60
  61 #define CONFIG_CMD_BOOTZ
  62
  63
  64 /*
  65  * Memory Configuration
  66  */
  67 #define CONFIG_NR_DRAM_BANKS            1
  68 #define CONFIG_SYS_SDRAM_BASE           0x20000000
  69 #define CONFIG_SYS_SDRAM_SIZE           SZ_32M
  70
  71 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
  72 #define CONFIG_SYS_MEMTEST_END          \
  73                 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K)
  74
  75 /*
  76  * LowLevel Init
  77  */
  78 #ifndef CONFIG_SKIP_LOWLEVEL_INIT
  79 #define CONFIG_SYS_USE_MAIN_OSCILLATOR
  80 /* flash */
  81 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000
  82 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */
  83
  84 /* clocks */
  85 #define CONFIG_SYS_PLLAR_VAL    0x20263E04 /* 179.712000 MHz for PCK */
  86 #define CONFIG_SYS_PLLBR_VAL    0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */
  87 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */
  88 #define CONFIG_SYS_MCKR_VAL     0x00000202
  89
  90 /* sdram */
  91 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */
  92 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000
  93 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000
  94 #define CONFIG_SYS_EBI_CSA_VAL  0x00000002 /* CS1=CONFIG_SYS_SDRAM */
  95 #define CONFIG_SYS_SDRC_CR_VAL  0x2188c155 /* set up the CONFIG_SYS_SDRAM */
  96 #define CONFIG_SYS_SDRAM        CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */
  97 #define CONFIG_SYS_SDRAM1       (CONFIG_SYS_SDRAM_BASE+0x80)
  98 #define CONFIG_SYS_SDRAM_VAL    0x00000000 /* value written to CONFIG_SYS_SDRAM */
  99 #define CONFIG_SYS_SDRC_MR_VAL  0x00000002 /* Precharge All */
 100 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */
 101 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */
 102 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */
 103 #define CONFIG_SYS_SDRC_TR_VAL  0x000002E0 /* Write refresh rate */
 104 #endif  /* CONFIG_SKIP_LOWLEVEL_INIT */
 105
 106 /*
 107  * Hardware drivers
 108  */
 109 /*
 110  * Choose a USART for serial console
 111  * CONFIG_DBGU is DBGU unit on J10
 112  * CONFIG_USART1 is USART1 on J14
 113  */
 114 #define CONFIG_ATMEL_USART
 115 #define CONFIG_USART_BASE       ATMEL_BASE_DBGU
 116 #define CONFIG_USART_ID         0/* ignored in arm */
 117
 118 #define CONFIG_BAUDRATE                 115200
 119
 120 /*
 121  * Command line configuration.
 122  */
 123 #define CONFIG_CMD_DHCP
 124 #define CONFIG_CMD_FAT
 125 #define CONFIG_CMD_MII
 126 #define CONFIG_CMD_PING
 127 #define CONFIG_CMD_USB
 128
 129 /*
 130  * Network Driver Setting
 131  */
 132 #define CONFIG_DRIVER_AT91EMAC
 133 #define CONFIG_SYS_RX_ETH_BUFFER        16
 134 #define CONFIG_RMII
 135 #define CONFIG_MII
 136
 137 /*
 138  * NOR Flash
 139  */
 140 #define CONFIG_FLASH_CFI_DRIVER
 141 #define CONFIG_SYS_FLASH_CFI
 142 #define CONFIG_SYS_FLASH_BASE           0x10000000
 143 #define PHYS_FLASH_1                    CONFIG_SYS_FLASH_BASE
 144 #define PHYS_FLASH_SIZE                 SZ_8M
 145 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 146 #define CONFIG_SYS_MAX_FLASH_SECT       256
 147 #define CONFIG_SYS_FLASH_PROTECTION
 148
 149 /*
 150  * USB Config
 151  */
 152 #define CONFIG_USB_ATMEL                        1
 153 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB
 154 #define CONFIG_USB_OHCI_NEW                     1
 155 #define CONFIG_USB_KEYBOARD                     1
 156 #define CONFIG_USB_STORAGE                      1
 157 #define CONFIG_DOS_PARTITION                    1
 158
 159 #define CONFIG_SYS_USB_OHCI_CPU_INIT            1
 160 #define CONFIG_SYS_USB_OHCI_REGS_BASE           ATMEL_USB_HOST_BASE
 161 #define CONFIG_SYS_USB_OHCI_SLOT_NAME           "at91rm9200"
 162 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 163
 164 /*
 165  * Environment Settings
 166  */
 167 #define CONFIG_ENV_IS_IN_FLASH
 168
 169 /*
 170  * after u-boot.bin
 171  */
 172 #define CONFIG_ENV_ADDR                 \
 173                 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
 174 #define CONFIG_ENV_SIZE                 SZ_64K /* sectors are 64K here */
 175 /* The following #defines are needed to get flash environment right */
 176 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 177 #define CONFIG_SYS_MONITOR_LEN          SZ_256K
 178
 179 /*
 180  * Boot option
 181  */
 182 #define CONFIG_BOOTDELAY                3
 183
 184 /* default load address */
 185 #define CONFIG_SYS_LOAD_ADDR            CONFIG_SYS_SDRAM_BASE + SZ_16M
 186 #define CONFIG_ENV_OVERWRITE
 187
 188 /*
 189  * Shell Settings
 190  */
 191 #define CONFIG_CMDLINE_EDITING
 192 #define CONFIG_SYS_LONGHELP
 193 #define CONFIG_AUTO_COMPLETE
 194 #define CONFIG_SYS_HUSH_PARSER
 195 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size */
 196 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 197 /* Print Buffer Size */
 198 #define CONFIG_SYS_PBSIZE               \
 199                 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 200
 201 /*
 202  * Size of malloc() pool
 203  */
 204 #define CONFIG_SYS_MALLOC_LEN           ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \
 205                                              SZ_4K)
 206
 207 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + SZ_4K \
 208                                         - GENERATED_GBL_DATA_SIZE)
 209
 210 #endif /* __AT91RM9200EK_CONFIG_H__ */