]> git.ipfire.org Git - people/ms/u-boot.git/blob - include/configs/axs10x.h
disk: convert CONFIG_DOS_PARTITION to Kconfig
[people/ms/u-boot.git] / include / configs / axs10x.h
1 /*
2 * Copyright (C) 2013-2016 Synopsys, Inc. All rights reserved.
3 *
4 * SPDX-License-Identifier: GPL-2.0+
5 */
6
7 #ifndef _CONFIG_AXS10X_H_
8 #define _CONFIG_AXS10X_H_
9
10 #include <linux/sizes.h>
11 /*
12 * CPU configuration
13 */
14 #define CONFIG_SYS_TIMER_RATE CONFIG_SYS_CLK_FREQ
15
16 #define ARC_FPGA_PERIPHERAL_BASE 0xE0000000
17 #define ARC_APB_PERIPHERAL_BASE 0xF0000000
18 #define ARC_DWMMC_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x15000)
19 #define ARC_DWGMAC_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x18000)
20
21 /*
22 * Memory configuration
23 */
24 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
25
26 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
27 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
28 #define CONFIG_SYS_SDRAM_SIZE SZ_512M
29
30 #define CONFIG_SYS_INIT_SP_ADDR \
31 (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
32
33 #define CONFIG_SYS_MALLOC_LEN SZ_2M
34 #define CONFIG_SYS_BOOTM_LEN SZ_32M
35 #define CONFIG_SYS_LOAD_ADDR 0x82000000
36
37 /*
38 * This board might be of different versions so handle it
39 */
40 #define CONFIG_BOARD_TYPES
41
42 /*
43 * NAND Flash configuration
44 */
45 #define CONFIG_SYS_NO_FLASH
46 #define CONFIG_SYS_NAND_BASE (ARC_FPGA_PERIPHERAL_BASE + 0x16000)
47 #define CONFIG_SYS_MAX_NAND_DEVICE 1
48
49 /*
50 * UART configuration
51 */
52 #define CONFIG_DW_SERIAL
53 #define CONFIG_SYS_NS16550_SERIAL
54 #define CONFIG_SYS_NS16550_CLK 33333333
55 #define CONFIG_SYS_NS16550_MEM32
56 #define CONFIG_BAUDRATE 115200
57
58 /*
59 * I2C configuration
60 */
61 #define CONFIG_SYS_I2C
62 #define CONFIG_I2C_ENV_EEPROM_BUS 2
63 #define CONFIG_SYS_I2C_SPEED 100000
64 #define CONFIG_SYS_I2C_SPEED1 100000
65 #define CONFIG_SYS_I2C_SPEED2 100000
66 #define CONFIG_SYS_I2C_SLAVE 0
67 #define CONFIG_SYS_I2C_SLAVE1 0
68 #define CONFIG_SYS_I2C_SLAVE2 0
69 #define CONFIG_SYS_I2C_BASE 0xE001D000
70 #define CONFIG_SYS_I2C_BASE1 0xE001E000
71 #define CONFIG_SYS_I2C_BASE2 0xE001F000
72 #define CONFIG_SYS_I2C_BUS_MAX 3
73 #define IC_CLK 50
74
75 /*
76 * EEPROM configuration
77 */
78 #define CONFIG_SYS_I2C_EEPROM_ADDR (0xA8 >> 1)
79 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
80 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 1
81 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
82 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 64
83
84 /*
85 * SD/MMC configuration
86 */
87 #define CONFIG_GENERIC_MMC
88
89 /*
90 * Ethernet PHY configuration
91 */
92 #define CONFIG_MII
93 #define CONFIG_PHY_GIGE
94
95 /*
96 * USB 1.1 configuration
97 */
98 #define CONFIG_USB_OHCI_NEW
99 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 1
100
101 /*
102 * Commands still not supported in Kconfig
103 */
104 #define CONFIG_CMD_NAND
105
106 #define CONFIG_AUTO_COMPLETE
107 #define CONFIG_SYS_MAXARGS 16
108
109 /*
110 * Environment settings
111 */
112 #define CONFIG_ENV_IS_IN_EEPROM
113 #define CONFIG_ENV_SIZE SZ_512
114 #define CONFIG_ENV_OFFSET 0
115
116 /*
117 * Environment configuration
118 */
119 #define CONFIG_BOOTFILE "uImage"
120 #define CONFIG_BOOTARGS "console=ttyS3,115200n8"
121 #define CONFIG_LOADADDR CONFIG_SYS_LOAD_ADDR
122
123 /*
124 * Console configuration
125 */
126 #define CONFIG_SYS_LONGHELP
127 #define CONFIG_SYS_CBSIZE SZ_256
128 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
129 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
130 sizeof(CONFIG_SYS_PROMPT) + 16)
131
132 /*
133 * Misc utility configuration
134 */
135 #define CONFIG_BOUNCE_BUFFER
136
137 #endif /* _CONFIG_AXS10X_H_ */