include/configs/bf533-stamp.h

   1 /*
   2  * U-boot - Configuration file for BF533 STAMP board
   3  */
   4
   5 #ifndef __CONFIG_BF533_STAMP_H__
   6 #define __CONFIG_BF533_STAMP_H__
   7
   8 #include <asm/config-pre.h>
   9
  10
  11 /*
  12  * Processor Settings
  13  */
  14 #define CONFIG_BFIN_CPU             bf533-0.3
  15 #define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
  16
  17 /*
  18  * Clock Settings
  19  *      CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
  20  *      SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
  21  */
  22 /* CONFIG_CLKIN_HZ is any value in Hz                                   */
  23 #define CONFIG_CLKIN_HZ                 11059200
  24 /* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN             */
  25 /*                                                1 = CLKIN / 2         */
  26 #define CONFIG_CLKIN_HALF               0
  27 /* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass     */
  28 /*                                                1 = bypass PLL        */
  29 #define CONFIG_PLL_BYPASS               0
  30 /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL              */
  31 /* Values can range from 0-63 (where 0 means 64)                        */
  32 #define CONFIG_VCO_MULT                 45
  33 /* CCLK_DIV controls the core clock divider                             */
  34 /* Values can be 1, 2, 4, or 8 ONLY                                     */
  35 #define CONFIG_CCLK_DIV                 1
  36 /* SCLK_DIV controls the system clock divider                           */
  37 /* Values can range from 1-15                                           */
  38 #define CONFIG_SCLK_DIV                 6 /* note: 1.2 boards can go faster */
  39
  40 /*
  41  * Memory Settings
  42  */
  43 #define CONFIG_MEM_ADD_WDTH     11
  44 #define CONFIG_MEM_SIZE         128
  45
  46 #define CONFIG_EBIU_SDRRC_VAL   0x268
  47 #define CONFIG_EBIU_SDGCTL_VAL  0x911109
  48
  49 #define CONFIG_EBIU_AMGCTL_VAL  0xFF
  50 #define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
  51 #define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
  52
  53 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)
  54 #define CONFIG_SYS_MALLOC_LEN   (384 * 1024)
  55
  56
  57 /*
  58  * Network Settings
  59  */
  60 #define ADI_CMDS_NETWORK        1
  61 #define CONFIG_SMC91111 1
  62 #define CONFIG_SMC91111_BASE    0x20300300
  63 #define SMC91111_EEPROM_INIT() \
  64         do { \
  65                 bfin_write_FIO_DIR(bfin_read_FIO_DIR() | PF1 | PF0); \
  66                 bfin_write_FIO_FLAG_C(PF1); \
  67                 bfin_write_FIO_FLAG_S(PF0); \
  68                 SSYNC(); \
  69         } while (0)
  70 #define CONFIG_HOSTNAME         bf533-stamp
  71 /* Uncomment next line to use fixed MAC address */
  72 /* #define CONFIG_ETHADDR       02:80:ad:20:31:b8 */
  73
  74
  75 /* I2C */
  76 #define CONFIG_SYS_I2C
  77 #define CONFIG_SYS_I2C_SOFT             /* I2C bit-banged */
  78 #define CONFIG_SYS_I2C_SOFT_SPEED       50000
  79 #define CONFIG_SYS_I2C_SOFT_SLAVE       0
  80 /*
  81  * Software (bit-bang) I2C driver configuration
  82  */
  83 #define CONFIG_SOFT_I2C_GPIO_SCL        GPIO_PF3
  84 #define CONFIG_SOFT_I2C_GPIO_SDA        GPIO_PF2
  85
  86 /*
  87  * Flash Settings
  88  */
  89 #define CONFIG_FLASH_CFI_DRIVER
  90 #define CONFIG_SYS_FLASH_BASE           0x20000000
  91 #define CONFIG_SYS_FLASH_CFI
  92 #define CONFIG_SYS_FLASH_CFI_AMD_RESET
  93 #define CONFIG_SYS_MAX_FLASH_BANKS      1
  94 #define CONFIG_SYS_MAX_FLASH_SECT       67
  95
  96 /*
  97  * SPI Settings
  98  */
  99 #define CONFIG_BFIN_SPI
 100 #define CONFIG_ENV_SPI_MAX_HZ   30000000
 101 /*
 102 #define CONFIG_SF_DEFAULT_SPEED 30000000
 103 #define CONFIG_SPI_FLASH
 104 #define CONFIG_SPI_FLASH_ALL
 105 */
 106
 107 /*
 108  * Env Storage Settings
 109  */
 110 #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
 111 #define CONFIG_ENV_IS_IN_SPI_FLASH
 112 #define CONFIG_ENV_OFFSET       0x10000
 113 #define CONFIG_ENV_SIZE         0x2000
 114 #define CONFIG_ENV_SECT_SIZE    0x10000
 115 #else
 116 #define CONFIG_ENV_IS_IN_FLASH
 117 #define CONFIG_ENV_OFFSET       0x4000
 118 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
 119 #define CONFIG_ENV_SIZE         0x2000
 120 #define CONFIG_ENV_SECT_SIZE    0x2000
 121 #endif
 122 #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
 123 #define ENV_IS_EMBEDDED
 124 #else
 125 #define CONFIG_ENV_IS_EMBEDDED_IN_LDR
 126 #endif
 127 #ifdef ENV_IS_EMBEDDED
 128 /* WARNING - the following is hand-optimized to fit within
 129  * the sector before the environment sector. If it throws
 130  * an error during compilation remove an object here to get
 131  * it linked after the configuration sector.
 132  */
 133 # define LDS_BOARD_TEXT \
 134         arch/blackfin/lib/built-in.o (.text*); \
 135         arch/blackfin/cpu/built-in.o (.text*); \
 136         . = DEFINED(env_offset) ? env_offset : .; \
 137         common/env_embedded.o (.text*);
 138 #endif
 139
 140
 141 /*
 142  * I2C Settings
 143  */
 144 #define CONFIG_SYS_I2C_SOFT
 145 #ifdef CONFIG_SYS_I2C_SOFT
 146 #define CONFIG_SYS_I2C
 147 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3
 148 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2
 149 #define I2C_DELAY               udelay(5)       /* 1/4 I2C clock duration */
 150 #define CONFIG_SYS_I2C_SOFT_SPEED       50000
 151 #define CONFIG_SYS_I2C_SOFT_SLAVE       0
 152 #endif
 153
 154 /*
 155  * Compact Flash / IDE / ATA Settings
 156  */
 157
 158 /* Enabled below option for CF support */
 159 /* #define CONFIG_STAMP_CF */
 160 #if defined(CONFIG_STAMP_CF)
 161 #define CONFIG_MISC_INIT_R
 162 #define CONFIG_DOS_PARTITION    1
 163 #undef  CONFIG_IDE_8xx_DIRECT           /* no pcmcia interface required */
 164 #undef  CONFIG_IDE_LED                  /* no led for ide supported */
 165 #undef  CONFIG_IDE_RESET                /* no reset for ide supported */
 166
 167 #define CONFIG_SYS_IDE_MAXBUS           1
 168 #define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS * 1)
 169
 170 #define CONFIG_SYS_ATA_BASE_ADDR        0x20200000
 171 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 172
 173 #define CONFIG_SYS_ATA_DATA_OFFSET      0x0020  /* data I/O */
 174 #define CONFIG_SYS_ATA_REG_OFFSET       0x0020  /* normal register accesses */
 175 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0007  /* alternate registers */
 176
 177 #define CONFIG_SYS_ATA_STRIDE           2
 178
 179 #undef CONFIG_EBIU_AMBCTL1_VAL
 180 #define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
 181 #endif
 182
 183
 184 /*
 185  * Misc Settings
 186  */
 187 #define CONFIG_RTC_BFIN
 188 #define CONFIG_UART_CONSOLE     0
 189
 190 /* FLASH/ETHERNET uses the same async bank */
 191 #define SHARED_RESOURCES        1
 192
 193 /* define to enable boot progress via leds */
 194 /* #define CONFIG_SHOW_BOOT_PROGRESS */
 195
 196 /* define to enable run status via led */
 197 /* #define CONFIG_STATUS_LED */
 198 #ifdef CONFIG_STATUS_LED
 199 #define CONFIG_GPIO_LED
 200 #define CONFIG_BOARD_SPECIFIC_LED
 201 /* use LED0 to indicate booting/alive */
 202 #define STATUS_LED_BOOT 0
 203 #define STATUS_LED_BIT GPIO_PF2
 204 #define STATUS_LED_STATE STATUS_LED_ON
 205 #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
 206 /* use LED1 to indicate crash */
 207 #define STATUS_LED_CRASH 1
 208 #define STATUS_LED_BIT1 GPIO_PF3
 209 #define STATUS_LED_STATE1 STATUS_LED_ON
 210 #define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
 211 /* #define STATUS_LED_BIT2 GPIO_PF4 */
 212 #endif
 213
 214 /* define to enable splash screen support */
 215 /* #define CONFIG_VIDEO */
 216
 217
 218 /*
 219  * Pull in common ADI header for remaining command/environment setup
 220  */
 221 #include <configs/bfin_adi_common.h>
 222
 223 #endif