include/configs/blackstamp.h

   1 /*
   2  * U-boot - Configuration file for BlackStamp board
   3  * Configuration by Ben Matthews for UR LLE using bf533-stamp.h
   4  * as a template
   5  * See http://blackfin.uclinux.org/gf/project/blackstamp/
   6  */
   7
   8 #ifndef __CONFIG_BLACKSTAMP_H__
   9 #define __CONFIG_BLACKSTAMP_H__
  10
  11 #include <asm/config-pre.h>
  12
  13 /*
  14  * Debugging: Set these options if you're having problems
  15  */
  16 /*
  17  * #define CONFIG_DEBUG_EARLY_SERIAL
  18  * #define DEBUG
  19  * #define CONFIG_DEBUG_DUMP
  20  * #define CONFIG_DEBUG_DUMP_SYMS
  21 */
  22 #define CONFIG_PANIC_HANG 0
  23
  24 /* CPU Options
  25  * Be sure to set the Silicon Revision Correctly
  26  */
  27 #define CONFIG_BFIN_CPU         bf532-0.5
  28 #define CONFIG_BFIN_BOOT_MODE   BFIN_BOOT_SPI_MASTER
  29
  30 /*
  31  * Board settings
  32  */
  33 #define CONFIG_NET_MULTI
  34 #define CONFIG_SMC91111 1
  35 #define CONFIG_SMC91111_BASE    0x20300300
  36
  37 /* FLASH/ETHERNET uses the same address range
  38  * Depending on what you have the CPLD doing
  39  * this probably isn't needed
  40  */
  41 #define SHARED_RESOURCES        1
  42
  43 /* Is I2C bit-banged? */
  44 #undef CONFIG_SOFT_I2
  45
  46 /*
  47  * Clock Settings
  48  *      CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
  49  *      SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
  50  */
  51 /* CONFIG_CLKIN_HZ is any value in Hz                                   */
  52 #define CONFIG_CLKIN_HZ                 25000000
  53 /* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN             */
  54 /*                                                1 = CLKIN / 2         */
  55 #define CONFIG_CLKIN_HALF               0
  56 /* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass     */
  57 /*                                                1 = bypass PLL        */
  58 #define CONFIG_PLL_BYPASS               0
  59 /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL              */
  60 /* Values can range from 0-63 (where 0 means 64)                        */
  61 #define CONFIG_VCO_MULT                 16
  62 /* CCLK_DIV controls the core clock divider                             */
  63 /* Values can be 1, 2, 4, or 8 ONLY                                     */
  64 #define CONFIG_CCLK_DIV                 1
  65 /* SCLK_DIV controls the system clock divider                           */
  66 /* Values can range from 1-15                                           */
  67 #define CONFIG_SCLK_DIV                 3
  68
  69 /*
  70  * Network settings
  71  */
  72
  73 #ifdef CONFIG_SMC91111
  74 #define CONFIG_IPADDR           192.168.0.15
  75 #define CONFIG_NETMASK          255.255.255.0
  76 #define CONFIG_GATEWAYIP        192.168.0.1
  77 #define CONFIG_SERVERIP         192.168.0.2
  78 #define CONFIG_HOSTNAME         blackstamp
  79 #define CONFIG_ROOTPATH         /checkout/uClinux-dist/romfs
  80 #define CONFIG_SYS_AUTOLOAD             "no"
  81
  82 /* To remove hardcoding and enable MAC storage in EEPROM  */
  83 /* #define CONFIG_ETHADDR               02:80:ad:20:31:b8 */
  84 #endif
  85
  86 #define CONFIG_ENV_IS_IN_SPI_FLASH
  87 #define CONFIG_ENV_OFFSET       0x40000
  88 #define CONFIG_ENV_SIZE         0x2000
  89 #define CONFIG_ENV_SECT_SIZE    0x40000
  90
  91 /*
  92  * SDRAM settings & memory map
  93  */
  94
  95 #define CONFIG_MEM_SIZE         64      /* 128, 64, 32, 16 */
  96 #define CONFIG_MEM_ADD_WDTH     10      /* 8, 9, 10, 11    */
  97
  98 #define CONFIG_SYS_MONITOR_LEN  (256 << 10)
  99 #define CONFIG_SYS_MALLOC_LEN   (384 << 10)
 100
 101 /*
 102  * Command settings
 103  */
 104
 105 #define CONFIG_SYS_LONGHELP             1
 106 #define CONFIG_CMDLINE_EDITING  1
 107 #define CONFIG_AUTO_COMPLETE    1
 108 #define CONFIG_ENV_OVERWRITE    1
 109
 110 #include <config_cmd_default.h>
 111
 112 #ifdef CONFIG_SMC91111
 113 # define CONFIG_CMD_DHCP
 114 # define CONFIG_CMD_PING
 115 #else
 116 # undef CONFIG_CMD_NET
 117 #endif
 118
 119 #ifdef CONFIG_SOFT_I2C
 120 # define CONFIG_CMD_I2C
 121 #endif
 122
 123 #define CONFIG_CMD_BOOTLDR
 124 #define CONFIG_CMD_CACHE
 125 #define CONFIG_CMD_CPLBINFO
 126 #define CONFIG_CMD_DATE
 127 #define CONFIG_CMD_SF
 128 #define CONFIG_CMD_ELF
 129
 130 #define CONFIG_BOOTDELAY     5
 131 #define CONFIG_BOOTCOMMAND   "run ramboot"
 132 #define CONFIG_BOOTARGS \
 133         "root=/dev/mtdblock0 rw " \
 134         "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \
 135         "earlyprintk=" \
 136                 "serial," \
 137                 "uart" MK_STR(CONFIG_UART_CONSOLE) "," \
 138                 MK_STR(CONFIG_BAUDRATE) " " \
 139         "console=ttyBF0," MK_STR(CONFIG_BAUDRATE)
 140
 141 #if defined(CONFIG_CMD_NET)
 142 # if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
 143 #  define UBOOT_ENV_FILE "u-boot.bin"
 144 # else
 145 #  define UBOOT_ENV_FILE "u-boot.ldr"
 146 # endif
 147 # if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
 148 #  ifdef CONFIG_SPI
 149 #   define UBOOT_ENV_UPDATE \
 150                 "eeprom write $(loadaddr) 0x0 $(filesize)"
 151 #  else
 152 #   define UBOOT_ENV_UPDATE \
 153                 "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \
 154                 "sf erase 0 0x40000;" \
 155                 "sf write $(loadaddr) 0 $(filesize)"
 156 #  endif
 157 # else
 158 #  define UBOOT_ENV_UPDATE \
 159                 "protect off 0x20000000 0x2003FFFF;" \
 160                 "erase 0x20000000 0x2003FFFF;" \
 161                 "cp.b $(loadaddr) 0x20000000 $(filesize)"
 162 # endif
 163 # define NETWORK_ENV_SETTINGS \
 164         "ubootfile=" UBOOT_ENV_FILE "\0" \
 165         "update=" \
 166                 "tftp $(loadaddr) $(ubootfile);" \
 167                 UBOOT_ENV_UPDATE \
 168                 "\0" \
 169         "addip=set bootargs $(bootargs) " \
 170                 "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
 171                    "$(hostname):eth0:off" \
 172                 "\0" \
 173         "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
 174         "ramboot=" \
 175                 "tftp $(loadaddr) uImage;" \
 176                 "run ramargs;" \
 177                 "run addip;" \
 178                 "bootm" \
 179                 "\0" \
 180         "nfsargs=set bootargs " \
 181                 "root=/dev/nfs rw " \
 182                 "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
 183                 "\0" \
 184         "nfsboot=" \
 185                 "tftp $(loadaddr) vmImage;" \
 186                 "run nfsargs;" \
 187                 "run addip;" \
 188                 "bootm" \
 189                 "\0"
 190 #else
 191 # define NETWORK_ENV_SETTINGS
 192 #endif
 193
 194 /*
 195  * Console settings
 196  */
 197 #define CONFIG_BAUDRATE         57600
 198 #define CONFIG_LOADS_ECHO       1
 199 #define CONFIG_UART_CONSOLE     0
 200
 201 /*
 202  * I2C settings
 203  * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
 204  * Located on the expansion connector on pins 86/85
 205  * Note these pins are arbitrarily chosen because we aren't using
 206  * them yet. You can (and probably should) change these values!
 207  */
 208 #ifdef CONFIG_SOFT_I2C
 209 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9
 210 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8
 211 #define CONFIG_SYS_I2C_SPEED            50000
 212 #define CONFIG_SYS_I2C_SLAVE            0xFE
 213 #endif
 214
 215 /*
 216  * Miscellaneous configurable options
 217  */
 218 #define CONFIG_RTC_BFIN         1
 219
 220 /*
 221  * Serial Flash Infomation
 222  */
 223 #define CONFIG_BFIN_SPI
 224 /* For the M25P64 SCK Should be Kept < 15Mhz */
 225 #define CONFIG_ENV_SPI_MAX_HZ   15000000
 226 #define CONFIG_SF_DEFAULT_SPEED 15000000
 227 #define CONFIG_SPI_FLASH
 228 #define CONFIG_SPI_FLASH_STMICRO
 229
 230 /*
 231  * FLASH organization and environment definitions
 232  */
 233
 234 #define CONFIG_EBIU_AMGCTL_VAL          0xFF
 235 #define CONFIG_EBIU_AMBCTL0_VAL         0xBBC3BBC3
 236 #define CONFIG_EBIU_AMBCTL1_VAL         0x99B39983
 237 #define CONFIG_EBIU_SDRRC_VAL           0x268
 238 #define CONFIG_EBIU_SDGCTL_VAL          0x911109
 239
 240 /* Even though Rev C boards have Parallel Flash
 241  * We aren't supporting it. Newer versions of the
 242  * hardware don't support Parallel Flash at all.
 243  */
 244 #define CONFIG_SYS_NO_FLASH
 245 #undef CONFIG_CMD_IMLS
 246 #undef CONFIG_CMD_JFFS2
 247 #undef CONFIG_CMD_FLASH
 248
 249 #endif