include/configs/cgtqmx6eval.h

   1 /*
   2  *
   3  * Congatec Conga-QEVAl board configuration file.
   4  *
   5  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   6  * Based on Freescale i.MX6Q Sabre Lite board configuration file.
   7  * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
   8  * Leo Sartre, <lsartre@adeneo-embedded.com>
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_CGTQMX6EVAL_H
  14 #define __CONFIG_CGTQMX6EVAL_H
  15
  16 #include "mx6_common.h"
  17
  18 #define CONFIG_MACH_TYPE        4122
  19
  20 #ifdef CONFIG_SPL
  21 #define CONFIG_SPL_SPI_SUPPORT
  22 #define CONFIG_SYS_SPI_U_BOOT_OFFS      (64 * 1024)
  23 #define CONFIG_SPL_SPI_LOAD
  24 #include "imx6_spl.h"
  25 #endif
  26
  27 /* Size of malloc() pool */
  28 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  29
  30 #define CONFIG_BOARD_EARLY_INIT_F
  31 #define CONFIG_BOARD_LATE_INIT
  32 #define CONFIG_MISC_INIT_R
  33
  34 #define CONFIG_MXC_UART
  35 #define CONFIG_MXC_UART_BASE           UART2_BASE
  36
  37 /* MMC Configs */
  38 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  39
  40 /* SPI NOR */
  41 #define CONFIG_SPI_FLASH
  42 #define CONFIG_SPI_FLASH_STMICRO
  43 #define CONFIG_SPI_FLASH_SST
  44 #define CONFIG_MXC_SPI
  45 #define CONFIG_SF_DEFAULT_BUS           0
  46 #define CONFIG_SF_DEFAULT_SPEED         20000000
  47 #define CONFIG_SF_DEFAULT_MODE          (SPI_MODE_0)
  48
  49 /* Miscellaneous commands */
  50 #define CONFIG_CMD_BMODE
  51
  52 /* Thermal support */
  53 #define CONFIG_IMX_THERMAL
  54
  55 /* I2C Configs */
  56 #define CONFIG_SYS_I2C
  57 #define CONFIG_SYS_I2C_MXC
  58 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  59 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  60 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  61 #define CONFIG_SYS_I2C_SPEED              100000
  62
  63 /* PMIC */
  64 #define CONFIG_POWER
  65 #define CONFIG_POWER_I2C
  66 #define CONFIG_POWER_PFUZE100
  67 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  68
  69 /* USB Configs */
  70 #define CONFIG_USB_EHCI
  71 #define CONFIG_USB_EHCI_MX6
  72 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  73 #define CONFIG_USB_HOST_ETHER
  74 #define CONFIG_USB_ETHER_ASIX
  75 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  76 #define CONFIG_MXC_USB_FLAGS    0
  77 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
  78 #define CONFIG_USB_KEYBOARD
  79 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  80
  81 #define CONFIG_USBD_HS
  82
  83 #define CONFIG_USB_FUNCTION_MASS_STORAGE
  84
  85 /* USB Device Firmware Update support */
  86 #define CONFIG_USB_FUNCTION_DFU
  87 #define CONFIG_DFU_MMC
  88 #define CONFIG_DFU_SF
  89
  90 #define CONFIG_USB_FUNCTION_FASTBOOT
  91 #define CONFIG_CMD_FASTBOOT
  92 #define CONFIG_ANDROID_BOOT_IMAGE
  93 #define CONFIG_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
  94 #define CONFIG_FASTBOOT_BUF_SIZE   0x07000000
  95
  96 /* Framebuffer */
  97 #define CONFIG_VIDEO
  98 #define CONFIG_VIDEO_IPUV3
  99 #define CONFIG_CFB_CONSOLE
 100 #define CONFIG_VGA_AS_SINGLE_DEVICE
 101 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 102 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 103 #define CONFIG_VIDEO_BMP_RLE8
 104 #define CONFIG_SPLASH_SCREEN
 105 #define CONFIG_SPLASH_SCREEN_ALIGN
 106 #define CONFIG_BMP_16BPP
 107 #define CONFIG_VIDEO_LOGO
 108 #define CONFIG_VIDEO_BMP_LOGO
 109 #ifdef CONFIG_MX6DL
 110 #define CONFIG_IPUV3_CLK 198000000
 111 #else
 112 #define CONFIG_IPUV3_CLK 264000000
 113 #endif
 114 #define CONFIG_IMX_HDMI
 115
 116 /* SATA */
 117 #define CONFIG_CMD_SATA
 118 #define CONFIG_DWC_AHSATA
 119 #define CONFIG_SYS_SATA_MAX_DEVICE      1
 120 #define CONFIG_DWC_AHSATA_PORT_ID       0
 121 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
 122 #define CONFIG_LBA48
 123 #define CONFIG_LIBATA
 124
 125 /* Ethernet */
 126 #define CONFIG_FEC_MXC
 127 #define CONFIG_MII
 128 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 129 #define CONFIG_FEC_XCV_TYPE             RGMII
 130 #define CONFIG_ETHPRIME                 "FEC"
 131 #define CONFIG_FEC_MXC_PHYADDR          6
 132 #define CONFIG_PHYLIB
 133 #define CONFIG_PHY_ATHEROS
 134
 135 /* Command definition */
 136
 137 #define CONFIG_MXC_UART_BASE    UART2_BASE
 138 #define CONFIG_CONSOLE_DEV      "ttymxc1"
 139 #define CONFIG_MMCROOT          "/dev/mmcblk0p2"
 140 #define CONFIG_SYS_MMC_ENV_DEV          0
 141
 142 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 143 #define CONFIG_EXTRA_ENV_SETTINGS \
 144         "script=boot.scr\0" \
 145         "image=zImage\0" \
 146         "fdtfile=undefined\0" \
 147         "fdt_addr_r=0x18000000\0" \
 148         "boot_fdt=try\0" \
 149         "ip_dyn=yes\0" \
 150         "console=" CONFIG_CONSOLE_DEV "\0" \
 151         "dfuspi=dfu 0 sf 0:0:10000000:0\0" \
 152         "dfu_alt_info_spl=spl raw 0x400\0" \
 153         "dfu_alt_info_img=u-boot raw 0x10000\0" \
 154         "dfu_alt_info=spl raw 0x400\0" \
 155         "bootm_size=0x10000000\0" \
 156         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 157         "mmcpart=1\0" \
 158         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 159         "update_sd_firmware=" \
 160                 "if test ${ip_dyn} = yes; then " \
 161                         "setenv get_cmd dhcp; " \
 162                 "else " \
 163                         "setenv get_cmd tftp; " \
 164                 "fi; " \
 165                 "if mmc dev ${mmcdev}; then "   \
 166                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 167                                 "setexpr fw_sz ${filesize} / 0x200; " \
 168                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 169                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 170                         "fi; "  \
 171                 "fi\0" \
 172         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 173                 "root=${mmcroot}\0" \
 174         "loadbootscript=" \
 175                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 176         "bootscript=echo Running bootscript from mmc ...; " \
 177                 "source\0" \
 178         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 179         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr_r} ${fdtfile}\0" \
 180         "mmcboot=echo Booting from mmc ...; " \
 181                 "run mmcargs; " \
 182                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 183                         "if run loadfdt; then " \
 184                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 185                         "else " \
 186                                 "if test ${boot_fdt} = try; then " \
 187                                         "bootz; " \
 188                                 "else " \
 189                                         "echo WARN: Cannot load the DT; " \
 190                                 "fi; " \
 191                         "fi; " \
 192                 "else " \
 193                         "bootz; " \
 194                 "fi;\0" \
 195         "findfdt="\
 196                 "if test $board_rev = MX6Q ; then " \
 197                         "setenv fdtfile imx6q-qmx6.dtb; fi; " \
 198                 "if test $board_rev = MX6DL ; then " \
 199                         "setenv fdtfile imx6dl-qmx6.dtb; fi; " \
 200                 "if test $fdtfile = undefined; then " \
 201                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 202         "netargs=setenv bootargs console=${console},${baudrate} " \
 203                 "root=/dev/nfs " \
 204                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 205         "netboot=echo Booting from net ...; " \
 206                 "run netargs; " \
 207                 "if test ${ip_dyn} = yes; then " \
 208                         "setenv get_cmd dhcp; " \
 209                 "else " \
 210                         "setenv get_cmd tftp; " \
 211                 "fi; " \
 212                 "${get_cmd} ${image}; " \
 213                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 214                         "if ${get_cmd} ${fdt_addr_r} ${fdtfile}; then " \
 215                                 "bootz ${loadaddr} - ${fdt_addr_r}; " \
 216                         "else " \
 217                                 "if test ${boot_fdt} = try; then " \
 218                                         "bootz; " \
 219                                 "else " \
 220                                         "echo WARN: Cannot load the DT; " \
 221                                 "fi; " \
 222                         "fi; " \
 223                 "else " \
 224                         "bootz; " \
 225                 "fi;\0" \
 226         "spilock=sf probe && sf protect lock 0x3f0000 0x10000;"\
 227
 228 #define CONFIG_BOOTCOMMAND \
 229         "run spilock;"      \
 230         "run findfdt; " \
 231         "mmc dev ${mmcdev};" \
 232         "if mmc rescan; then " \
 233                 "if run loadbootscript; then " \
 234                 "run bootscript; " \
 235                 "else " \
 236                         "if run loadimage; then " \
 237                                 "run mmcboot; " \
 238                         "else run netboot; " \
 239                         "fi; " \
 240                 "fi; " \
 241         "else run netboot; fi"
 242
 243 #define CONFIG_SYS_MEMTEST_START       0x10000000
 244 #define CONFIG_SYS_MEMTEST_END         0x10010000
 245 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 246
 247 /* Physical Memory Map */
 248 #define CONFIG_NR_DRAM_BANKS           1
 249 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 250
 251 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 252 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 253 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 254
 255 #define CONFIG_SYS_INIT_SP_OFFSET \
 256         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 257 #define CONFIG_SYS_INIT_SP_ADDR \
 258         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 259
 260 /* Environment organization */
 261 #if defined (CONFIG_ENV_IS_IN_MMC)
 262 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 263 #define CONFIG_SYS_MMC_ENV_DEV          0
 264 #endif
 265
 266 #define CONFIG_ENV_SIZE                 (8 * 1024)
 267
 268 #define CONFIG_ENV_IS_IN_SPI_FLASH
 269 #if defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 270 #define CONFIG_ENV_OFFSET               (768 * 1024)
 271 #define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 272 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 273 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 274 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 275 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 276 #endif
 277
 278 #endif                         /* __CONFIG_CGTQMX6EVAL_H */