include/configs/da850evm.h

   1 /*
   2  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
   3  *
   4  * Based on davinci_dvevm.h. Original Copyrights follow:
   5  *
   6  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __CONFIG_H
  12 #define __CONFIG_H
  13
  14 /*
  15  * Board
  16  */
  17 #define CONFIG_DRIVER_TI_EMAC
  18 /* check if direct NOR boot config is used */
  19 #ifndef CONFIG_DIRECT_NOR_BOOT
  20 #define CONFIG_USE_SPIFLASH
  21 #endif
  22
  23 /*
  24 * Disable DM_* for SPL build and can be re-enabled after adding
  25 * DM support in SPL
  26 */
  27 #ifdef CONFIG_SPL_BUILD
  28 #undef CONFIG_DM_SPI
  29 #undef CONFIG_DM_SPI_FLASH
  30 #undef CONFIG_DM_I2C
  31 #undef CONFIG_DM_I2C_COMPAT
  32 #endif
  33 /*
  34  * SoC Configuration
  35  */
  36 #define CONFIG_SYS_EXCEPTION_VECTORS_HIGH
  37 #define CONFIG_SYS_CLK_FREQ             clk_get(DAVINCI_ARM_CLKID)
  38 #define CONFIG_SYS_OSCIN_FREQ           24000000
  39 #define CONFIG_SYS_TIMERBASE            DAVINCI_TIMER0_BASE
  40 #define CONFIG_SYS_HZ_CLOCK             clk_get(DAVINCI_AUXCLK_CLKID)
  41
  42 #ifdef CONFIG_DIRECT_NOR_BOOT
  43 #define CONFIG_ARCH_CPU_INIT
  44 #define CONFIG_DA8XX_GPIO
  45 #define CONFIG_SYS_TEXT_BASE            0x60000000
  46 #define CONFIG_SYS_DV_NOR_BOOT_CFG      (0x11)
  47 #else
  48 #define CONFIG_SYS_TEXT_BASE            0xc1080000
  49 #endif
  50
  51 /*
  52  * Memory Info
  53  */
  54 #define CONFIG_SYS_MALLOC_LEN   (0x10000 + 1*1024*1024) /* malloc() len */
  55 #define PHYS_SDRAM_1            DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
  56 #define PHYS_SDRAM_1_SIZE       (64 << 20) /* SDRAM size 64MB */
  57 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
  58
  59 /* memtest start addr */
  60 #define CONFIG_SYS_MEMTEST_START        (PHYS_SDRAM_1 + 0x2000000)
  61
  62 /* memtest will be run on 16MB */
  63 #define CONFIG_SYS_MEMTEST_END  (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
  64
  65 #define CONFIG_NR_DRAM_BANKS    1 /* we have 1 bank of DRAM */
  66
  67 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (       \
  68         DAVINCI_SYSCFG_SUSPSRC_TIMER0 |         \
  69         DAVINCI_SYSCFG_SUSPSRC_SPI1 |           \
  70         DAVINCI_SYSCFG_SUSPSRC_UART2 |          \
  71         DAVINCI_SYSCFG_SUSPSRC_EMAC |           \
  72         DAVINCI_SYSCFG_SUSPSRC_I2C)
  73
  74 /*
  75  * PLL configuration
  76  */
  77 #define CONFIG_SYS_DV_CLKMODE          0
  78 #define CONFIG_SYS_DA850_PLL0_POSTDIV  1
  79 #define CONFIG_SYS_DA850_PLL0_PLLDIV1  0x8000
  80 #define CONFIG_SYS_DA850_PLL0_PLLDIV2  0x8001
  81 #define CONFIG_SYS_DA850_PLL0_PLLDIV3  0x8002
  82 #define CONFIG_SYS_DA850_PLL0_PLLDIV4  0x8003
  83 #define CONFIG_SYS_DA850_PLL0_PLLDIV5  0x8002
  84 #define CONFIG_SYS_DA850_PLL0_PLLDIV6  CONFIG_SYS_DA850_PLL0_PLLDIV1
  85 #define CONFIG_SYS_DA850_PLL0_PLLDIV7  0x8005
  86
  87 #define CONFIG_SYS_DA850_PLL1_POSTDIV  1
  88 #define CONFIG_SYS_DA850_PLL1_PLLDIV1  0x8000
  89 #define CONFIG_SYS_DA850_PLL1_PLLDIV2  0x8001
  90 #define CONFIG_SYS_DA850_PLL1_PLLDIV3  0x8002
  91
  92 #define CONFIG_SYS_DA850_PLL0_PLLM     24
  93 #define CONFIG_SYS_DA850_PLL1_PLLM     21
  94
  95 /*
  96  * DDR2 memory configuration
  97  */
  98 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
  99                                         DV_DDR_PHY_EXT_STRBEN | \
 100                                         (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT))
 101
 102 #define CONFIG_SYS_DA850_DDR2_SDBCR (           \
 103         (1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) |     \
 104         (1 << DV_DDR_SDCR_DDREN_SHIFT) |        \
 105         (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) |      \
 106         (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) |    \
 107         (0x3 << DV_DDR_SDCR_CL_SHIFT) |         \
 108         (0x2 << DV_DDR_SDCR_IBANK_SHIFT) |      \
 109         (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
 110
 111 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
 112 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0
 113
 114 #define CONFIG_SYS_DA850_DDR2_SDTIMR (          \
 115         (14 << DV_DDR_SDTMR1_RFC_SHIFT) |       \
 116         (2 << DV_DDR_SDTMR1_RP_SHIFT) |         \
 117         (2 << DV_DDR_SDTMR1_RCD_SHIFT) |        \
 118         (1 << DV_DDR_SDTMR1_WR_SHIFT) |         \
 119         (5 << DV_DDR_SDTMR1_RAS_SHIFT) |        \
 120         (8 << DV_DDR_SDTMR1_RC_SHIFT) |         \
 121         (1 << DV_DDR_SDTMR1_RRD_SHIFT) |        \
 122         (0 << DV_DDR_SDTMR1_WTR_SHIFT))
 123
 124 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 (         \
 125         (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) |     \
 126         (0 << DV_DDR_SDTMR2_XP_SHIFT) |         \
 127         (0 << DV_DDR_SDTMR2_ODT_SHIFT) |        \
 128         (17 << DV_DDR_SDTMR2_XSNR_SHIFT) |      \
 129         (199 << DV_DDR_SDTMR2_XSRD_SHIFT) |     \
 130         (0 << DV_DDR_SDTMR2_RTP_SHIFT) |        \
 131         (0 << DV_DDR_SDTMR2_CKE_SHIFT))
 132
 133 #define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000494
 134 #define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
 135
 136 /*
 137  * Serial Driver info
 138  */
 139
 140 #if defined(CONFIG_SPL_BUILD) || defined(CONFIG_DIRECT_NOR_BOOT)
 141 #define CONFIG_SYS_NS16550_SERIAL
 142 #define CONFIG_SYS_NS16550_REG_SIZE     -4      /* NS16550 register size */
 143 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
 144 #endif
 145 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
 146 #define CONFIG_CONS_INDEX       1               /* use UART0 for console */
 147
 148 #define CONFIG_SPI
 149 #define CONFIG_SYS_SPI_CLK              clk_get(DAVINCI_SPI1_CLKID)
 150 #ifdef CONFIG_SPL_BUILD
 151 #define CONFIG_SYS_SPI_BASE             DAVINCI_SPI1_BASE
 152 #define CONFIG_SF_DEFAULT_SPEED         30000000
 153 #define CONFIG_ENV_SPI_MAX_HZ   CONFIG_SF_DEFAULT_SPEED
 154 #endif
 155
 156 #ifdef CONFIG_USE_SPIFLASH
 157 #define CONFIG_SPL_SPI_LOAD
 158 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x8000
 159 #define CONFIG_SYS_SPI_U_BOOT_SIZE      0x40000
 160 #endif
 161
 162 /*
 163  * I2C Configuration
 164  */
 165 #ifndef CONFIG_SPL_BUILD
 166 #define CONFIG_SYS_I2C_DAVINCI
 167 #define CONFIG_SYS_I2C_EXPANDER_ADDR   0x20
 168 #endif
 169
 170 /*
 171  * Flash & Environment
 172  */
 173 #ifdef CONFIG_USE_NAND
 174 #define CONFIG_NAND_DAVINCI
 175 #define CONFIG_ENV_OFFSET               0x0 /* Block 0--not used by bootcode */
 176 #define CONFIG_ENV_SIZE                 (128 << 10)
 177 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 178 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
 179 #define CONFIG_SYS_NAND_PAGE_2K
 180 #define CONFIG_SYS_NAND_CS              3
 181 #define CONFIG_SYS_NAND_BASE            DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
 182 #define CONFIG_SYS_NAND_MASK_CLE                0x10
 183 #define CONFIG_SYS_NAND_MASK_ALE                0x8
 184 #undef CONFIG_SYS_NAND_HW_ECC
 185 #define CONFIG_SYS_MAX_NAND_DEVICE      1 /* Max number of NAND devices */
 186 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
 187 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 188 #define CONFIG_SYS_NAND_PAGE_SIZE       (2 << 10)
 189 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 << 10)
 190 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x28000
 191 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x60000
 192 #define CONFIG_SYS_NAND_U_BOOT_DST      0xc1080000
 193 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
 194 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
 195                                         CONFIG_SYS_NAND_U_BOOT_SIZE - \
 196                                         CONFIG_SYS_MALLOC_LEN -       \
 197                                         GENERATED_GBL_DATA_SIZE)
 198 #define CONFIG_SYS_NAND_ECCPOS          {                               \
 199                                 24, 25, 26, 27, 28, \
 200                                 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, \
 201                                 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, \
 202                                 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, \
 203                                 59, 60, 61, 62, 63 }
 204 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 205 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 206 #define CONFIG_SYS_NAND_ECCSIZE         512
 207 #define CONFIG_SYS_NAND_ECCBYTES        10
 208 #define CONFIG_SYS_NAND_OOBSIZE         64
 209 #define CONFIG_SPL_NAND_BASE
 210 #define CONFIG_SPL_NAND_DRIVERS
 211 #define CONFIG_SPL_NAND_ECC
 212 #define CONFIG_SPL_NAND_LOAD
 213 #endif
 214
 215 /*
 216  * Network & Ethernet Configuration
 217  */
 218 #ifdef CONFIG_DRIVER_TI_EMAC
 219 #define CONFIG_MII
 220 #define CONFIG_BOOTP_DNS
 221 #define CONFIG_BOOTP_DNS2
 222 #define CONFIG_BOOTP_SEND_HOSTNAME
 223 #define CONFIG_NET_RETRY_COUNT  10
 224 #endif
 225
 226 #ifdef CONFIG_USE_NOR
 227 #define CONFIG_FLASH_CFI_DRIVER
 228 #define CONFIG_SYS_FLASH_CFI
 229 #define CONFIG_SYS_FLASH_PROTECTION
 230 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* max number of flash banks */
 231 #define CONFIG_SYS_FLASH_SECT_SZ        (128 << 10) /* 128KB */
 232 #define CONFIG_ENV_OFFSET               (CONFIG_SYS_FLASH_SECT_SZ * 3)
 233 #define CONFIG_ENV_SIZE                 (10 << 10) /* 10KB */
 234 #define CONFIG_SYS_FLASH_BASE           DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
 235 #define PHYS_FLASH_SIZE                 (8 << 20) /* Flash size 8MB */
 236 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
 237                + 3)
 238 #define CONFIG_ENV_SECT_SIZE            CONFIG_SYS_FLASH_SECT_SZ
 239 #endif
 240
 241 #ifdef CONFIG_USE_SPIFLASH
 242 #define CONFIG_ENV_SIZE                 (64 << 10)
 243 #define CONFIG_ENV_OFFSET               (512 << 10)
 244 #define CONFIG_ENV_SECT_SIZE            (64 << 10)
 245 #ifdef CONFIG_SPL_BUILD
 246 #undef CONFIG_SPI_FLASH_MTD
 247 #endif
 248 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 249 #define CONFIG_MTD_PARTITIONS           /* required for UBI partition support */
 250 #endif
 251
 252 /*
 253  * U-Boot general configuration
 254  */
 255 #define CONFIG_MISC_INIT_R
 256 #define CONFIG_BOOTFILE         "uImage" /* Boot file name */
 257 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 258 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
 259 #define CONFIG_SYS_LOAD_ADDR    (PHYS_SDRAM_1 + 0x700000)
 260 #define CONFIG_AUTO_COMPLETE
 261 #define CONFIG_CMDLINE_EDITING
 262 #define CONFIG_SYS_LONGHELP
 263 #define CONFIG_MX_CYCLIC
 264
 265 /*
 266  * Linux Information
 267  */
 268 #define LINUX_BOOT_PARAM_ADDR   (PHYS_SDRAM_1 + 0x100)
 269 #define CONFIG_HWCONFIG         /* enable hwconfig */
 270 #define CONFIG_CMDLINE_TAG
 271 #define CONFIG_REVISION_TAG
 272 #define CONFIG_SETUP_MEMORY_TAGS
 273
 274 #define CONFIG_BOOTCOMMAND \
 275                 "run envboot; " \
 276                 "run mmcboot; "
 277
 278 #define DEFAULT_LINUX_BOOT_ENV \
 279         "loadaddr=0xc0700000\0" \
 280         "fdtaddr=0xc0600000\0" \
 281         "scriptaddr=0xc0600000\0"
 282
 283 #include <environment/ti/mmc.h>
 284
 285 #define CONFIG_EXTRA_ENV_SETTINGS \
 286         DEFAULT_LINUX_BOOT_ENV \
 287         DEFAULT_MMC_TI_ARGS \
 288         "bootpart=0:2\0" \
 289         "bootdir=/boot\0" \
 290         "bootfile=zImage\0" \
 291         "fdtfile=da850-evm.dtb\0" \
 292         "boot_fdt=yes\0" \
 293         "boot_fit=0\0" \
 294         "console=ttyS2,115200n8\0" \
 295         "hwconfig=dsp:wake=yes"
 296
 297 #ifdef CONFIG_CMD_BDI
 298 #define CONFIG_CLOCKS
 299 #endif
 300
 301 #ifdef CONFIG_USE_NAND
 302 #define CONFIG_MTD_DEVICE
 303 #define CONFIG_MTD_PARTITIONS
 304 #endif
 305
 306 #if !defined(CONFIG_USE_NAND) && \
 307         !defined(CONFIG_USE_NOR) && \
 308         !defined(CONFIG_USE_SPIFLASH)
 309 #define CONFIG_ENV_SIZE         (16 << 10)
 310 #endif
 311
 312 #ifndef CONFIG_DIRECT_NOR_BOOT
 313 /* defines for SPL */
 314 #define CONFIG_SPL_FRAMEWORK
 315 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE - \
 316                                                 CONFIG_SYS_MALLOC_LEN)
 317 #define CONFIG_SYS_SPL_MALLOC_SIZE      CONFIG_SYS_MALLOC_LEN
 318 #define CONFIG_SPL_SPI_LOAD
 319 #define CONFIG_SPL_STACK        0x8001ff00
 320 #define CONFIG_SPL_TEXT_BASE    0x80000000
 321 #define CONFIG_SPL_MAX_FOOTPRINT        32768
 322 #define CONFIG_SPL_PAD_TO       32768
 323 #endif
 324
 325 /* Load U-Boot Image From MMC */
 326 #ifdef CONFIG_SPL_MMC_LOAD
 327 #undef CONFIG_SPL_SPI_LOAD
 328 #endif
 329
 330 /* additions for new relocation code, must added to all boards */
 331 #define CONFIG_SYS_SDRAM_BASE           0xc0000000
 332
 333 #ifdef CONFIG_DIRECT_NOR_BOOT
 334 #define CONFIG_SYS_INIT_SP_ADDR         0x8001ff00
 335 #else
 336 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
 337                                         GENERATED_GBL_DATA_SIZE)
 338 #endif /* CONFIG_DIRECT_NOR_BOOT */
 339
 340 #include <asm/arch/hardware.h>
 341
 342 #endif /* __CONFIG_H */