include/configs/dreamplug.h

   1 /*
   2  * (C) Copyright 2011
   3  * Jason Cooper <u-boot@lakedaemon.net>
   4  *
   5  * Based on work by:
   6  * Marvell Semiconductor <www.marvell.com>
   7  * Written-by: Siddarth Gore <gores@marvell.com>
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11
  12 #ifndef _CONFIG_DREAMPLUG_H
  13 #define _CONFIG_DREAMPLUG_H
  14
  15 /*
  16  * High Level Configuration Options (easy to change)
  17  */
  18 #define CONFIG_SHEEVA_88SV131   1       /* CPU Core subversion */
  19 #define CONFIG_MACH_TYPE        MACH_TYPE_DREAMPLUG
  20
  21 /*
  22  * Commands configuration
  23  */
  24
  25 /*
  26  * mv-plug-common.h should be defined after CMD configs since it used them
  27  * to enable certain macros
  28  */
  29 #include "mv-plug-common.h"
  30
  31 /*
  32  *  Environment variables configurations
  33  */
  34 #ifdef CONFIG_SPI_FLASH
  35 #define CONFIG_ENV_SECT_SIZE            0x10000 /* 64k */
  36 #endif
  37
  38 #ifdef CONFIG_CMD_SF
  39 #define CONFIG_HARD_SPI                 1
  40 #define CONFIG_ENV_SPI_BUS              0
  41 #define CONFIG_ENV_SPI_CS               0
  42 #define CONFIG_ENV_SPI_MAX_HZ           50000000 /* 50 MHz */
  43 #endif
  44
  45 /*
  46  * max 4k env size is enough, but in case of nand
  47  * it has to be rounded to sector size
  48  */
  49 #define CONFIG_ENV_SIZE                 0x1000  /* 4k */
  50 #define CONFIG_ENV_ADDR                 0x100000
  51 #define CONFIG_ENV_OFFSET               0x100000 /* env starts here */
  52
  53 /*
  54  * Default environment variables
  55  */
  56 #define CONFIG_BOOTCOMMAND              "setenv ethact egiga0; " \
  57         "${x_bootcmd_ethernet}; setenv ethact egiga1; " \
  58         "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\
  59         "setenv bootargs ${x_bootargs} ${x_bootargs_root}; "    \
  60         "bootm 0x6400000;"
  61
  62 #define CONFIG_EXTRA_ENV_SETTINGS       \
  63         "x_bootcmd_ethernet=ping 192.168.2.1\0" \
  64         "x_bootcmd_usb=usb start\0"     \
  65         "x_bootcmd_kernel=fatload usb 0 0x6400000 uImage\0" \
  66         "x_bootargs=console=ttyS0,115200\0"     \
  67         "x_bootargs_root=root=/dev/sda2 rootdelay=10\0"
  68
  69 /*
  70  * Ethernet Driver configuration
  71  */
  72 #ifdef CONFIG_CMD_NET
  73 #define CONFIG_MVGBE_PORTS      {1, 1}  /* enable both ports */
  74 #define CONFIG_PHY_BASE_ADR     0
  75 #endif /* CONFIG_CMD_NET */
  76
  77 /*
  78  * SATA Driver configuration
  79  */
  80 #ifdef CONFIG_MVSATA_IDE
  81 #define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
  82 #endif /*CONFIG_MVSATA_IDE*/
  83
  84 #endif /* _CONFIG_DREAMPLUG_H */