include/configs/exynos5-common.h

   1 /*
   2  * Copyright (C) 2013 Samsung Electronics
   3  *
   4  * Configuration settings for the SAMSUNG EXYNOS5 board.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_EXYNOS5_COMMON_H
  10 #define __CONFIG_EXYNOS5_COMMON_H
  11
  12 #define CONFIG_EXYNOS5                  /* Exynos5 Family */
  13
  14 #include "exynos-common.h"
  15
  16 #define CONFIG_SYS_CACHELINE_SIZE       64
  17 #define CONFIG_EXYNOS_SPL
  18
  19 /* Allow tracing to be enabled */
  20 #define CONFIG_TRACE
  21 #define CONFIG_CMD_TRACE
  22 #define CONFIG_TRACE_BUFFER_SIZE        (16 << 20)
  23 #define CONFIG_TRACE_EARLY_SIZE         (8 << 20)
  24 #define CONFIG_TRACE_EARLY
  25 #define CONFIG_TRACE_EARLY_ADDR         0x50000000
  26
  27
  28 /* Enable ACE acceleration for SHA1 and SHA256 */
  29 #define CONFIG_EXYNOS_ACE_SHA
  30 #define CONFIG_SHA_HW_ACCEL
  31
  32 /* Power Down Modes */
  33 #define S5P_CHECK_SLEEP                 0x00000BAD
  34 #define S5P_CHECK_DIDLE                 0xBAD00000
  35 #define S5P_CHECK_LPA                   0xABAD0000
  36
  37 /* Offset for inform registers */
  38 #define INFORM0_OFFSET                  0x800
  39 #define INFORM1_OFFSET                  0x804
  40 #define INFORM2_OFFSET                  0x808
  41 #define INFORM3_OFFSET                  0x80c
  42
  43 /* select serial console configuration */
  44 #define CONFIG_BAUDRATE                 115200
  45 #define EXYNOS5_DEFAULT_UART_OFFSET     0x010000
  46 #define CONFIG_SILENT_CONSOLE
  47 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
  48 #define CONFIG_CONSOLE_MUX
  49
  50 #define EXYNOS_DEVICE_SETTINGS \
  51                 "stdin=serial\0" \
  52                 "stdout=serial\0" \
  53                 "stderr=serial\0"
  54
  55 #define CONFIG_EXTRA_ENV_SETTINGS \
  56         EXYNOS_DEVICE_SETTINGS
  57
  58 #define CONFIG_CMD_PING
  59 #define CONFIG_CMD_ELF
  60 #define CONFIG_CMD_NET
  61 #define CONFIG_CMD_HASH
  62
  63 /* Thermal Management Unit */
  64 #define CONFIG_EXYNOS_TMU
  65 #define CONFIG_CMD_DTT
  66 #define CONFIG_TMU_CMD_DTT
  67
  68 /* TPM */
  69 #define CONFIG_TPM
  70 #define CONFIG_CMD_TPM
  71 #define CONFIG_TPM_TIS_I2C
  72 #define CONFIG_TPM_TIS_I2C_BUS_NUMBER   3
  73 #define CONFIG_TPM_TIS_I2C_SLAVE_ADDR   0x20
  74
  75 /* MMC SPL */
  76 #define COPY_BL2_FNPTR_ADDR     0x02020030
  77 #define CONFIG_SUPPORT_EMMC_BOOT
  78
  79 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  80 #define CONFIG_SPL_GPIO_SUPPORT
  81
  82 /* specific .lds file */
  83 #define CONFIG_SPL_LDSCRIPT     "board/samsung/common/exynos-uboot-spl.lds"
  84
  85 /* Boot Argument Buffer Size */
  86 /* memtest works on */
  87 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE
  88 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_SDRAM_BASE + 0x5E00000)
  89 #define CONFIG_SYS_LOAD_ADDR            (CONFIG_SYS_SDRAM_BASE + 0x3E00000)
  90
  91 #define CONFIG_RD_LVL
  92
  93 #define PHYS_SDRAM_1            CONFIG_SYS_SDRAM_BASE
  94 #define PHYS_SDRAM_1_SIZE       SDRAM_BANK_SIZE
  95 #define PHYS_SDRAM_2            (CONFIG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
  96 #define PHYS_SDRAM_2_SIZE       SDRAM_BANK_SIZE
  97 #define PHYS_SDRAM_3            (CONFIG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
  98 #define PHYS_SDRAM_3_SIZE       SDRAM_BANK_SIZE
  99 #define PHYS_SDRAM_4            (CONFIG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
 100 #define PHYS_SDRAM_4_SIZE       SDRAM_BANK_SIZE
 101 #define PHYS_SDRAM_5            (CONFIG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
 102 #define PHYS_SDRAM_5_SIZE       SDRAM_BANK_SIZE
 103 #define PHYS_SDRAM_6            (CONFIG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
 104 #define PHYS_SDRAM_6_SIZE       SDRAM_BANK_SIZE
 105 #define PHYS_SDRAM_7            (CONFIG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
 106 #define PHYS_SDRAM_7_SIZE       SDRAM_BANK_SIZE
 107 #define PHYS_SDRAM_8            (CONFIG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
 108 #define PHYS_SDRAM_8_SIZE       SDRAM_BANK_SIZE
 109
 110 #define CONFIG_SYS_MONITOR_BASE 0x00000000
 111
 112 #define CONFIG_SYS_MMC_ENV_DEV          0
 113
 114 #define CONFIG_SECURE_BL1_ONLY
 115
 116 /* Secure FW size configuration */
 117 #ifdef CONFIG_SECURE_BL1_ONLY
 118 #define CONFIG_SEC_FW_SIZE (8 << 10) /* 8KB */
 119 #else
 120 #define CONFIG_SEC_FW_SIZE 0
 121 #endif
 122
 123 /* Configuration of BL1, BL2, ENV Blocks on mmc */
 124 #define CONFIG_RES_BLOCK_SIZE   (512)
 125 #define CONFIG_BL1_SIZE (16 << 10) /*16 K reserved for BL1*/
 126 #define CONFIG_BL2_SIZE (512UL << 10UL) /* 512 KB */
 127 #define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
 128
 129 #define CONFIG_BL1_OFFSET       (CONFIG_RES_BLOCK_SIZE + CONFIG_SEC_FW_SIZE)
 130 #define CONFIG_BL2_OFFSET       (CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
 131
 132 /* U-boot copy size from boot Media to DRAM.*/
 133 #define BL2_START_OFFSET        (CONFIG_BL2_OFFSET/512)
 134 #define BL2_SIZE_BLOC_COUNT     (CONFIG_BL2_SIZE/512)
 135
 136 #define EXYNOS_COPY_SPI_FNPTR_ADDR      0x02020058
 137 #define SPI_FLASH_UBOOT_POS     (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
 138
 139 /* I2C */
 140 #define CONFIG_SYS_I2C_INIT_BOARD
 141 #define CONFIG_SYS_I2C
 142 #define CONFIG_CMD_I2C
 143 #define CONFIG_SYS_I2C_S3C24X0_SPEED    100000          /* 100 Kbps */
 144 #define CONFIG_SYS_I2C_S3C24X0
 145 #define CONFIG_I2C_MULTI_BUS
 146 #define CONFIG_SYS_I2C_S3C24X0_SLAVE    0x0
 147 #define CONFIG_I2C_EDID
 148
 149 /* SPI */
 150 #ifdef CONFIG_SPI_FLASH
 151 #define CONFIG_EXYNOS_SPI
 152 #define CONFIG_CMD_SF
 153 #define CONFIG_CMD_SPI
 154 #define CONFIG_SPI_FLASH_WINBOND
 155 #define CONFIG_SPI_FLASH_GIGADEVICE
 156 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 157 #define CONFIG_SF_DEFAULT_SPEED         50000000
 158 #define EXYNOS5_SPI_NUM_CONTROLLERS     5
 159 #define CONFIG_OF_SPI
 160 #endif
 161
 162 #ifdef CONFIG_ENV_IS_IN_SPI_FLASH
 163 #define CONFIG_ENV_SPI_MODE     SPI_MODE_0
 164 #define CONFIG_ENV_SECT_SIZE    CONFIG_ENV_SIZE
 165 #define CONFIG_ENV_SPI_BUS      1
 166 #define CONFIG_ENV_SPI_MAX_HZ   50000000
 167 #endif
 168
 169 /* Ethernet Controllor Driver */
 170 #ifdef CONFIG_CMD_NET
 171 #define CONFIG_SMC911X
 172 #define CONFIG_SMC911X_BASE             0x5000000
 173 #define CONFIG_SMC911X_16_BIT
 174 #define CONFIG_ENV_SROM_BANK            1
 175 #endif /*CONFIG_CMD_NET*/
 176
 177 /* Enable PXE Support */
 178 #ifdef CONFIG_CMD_NET
 179 #define CONFIG_CMD_PXE
 180 #define CONFIG_MENU
 181 #endif
 182
 183 /* SHA hashing */
 184 #define CONFIG_CMD_HASH
 185 #define CONFIG_HASH_VERIFY
 186 #define CONFIG_SHA1
 187 #define CONFIG_SHA256
 188
 189 /* Enable Time Command */
 190 #define CONFIG_CMD_TIME
 191
 192 #define CONFIG_CMD_BOOTZ
 193
 194 #define CONFIG_CMD_GPIO
 195
 196 /* USB boot mode */
 197 #define CONFIG_USB_BOOTING
 198 #define EXYNOS_COPY_USB_FNPTR_ADDR      0x02020070
 199 #define EXYNOS_USB_SECONDARY_BOOT       0xfeed0002
 200 #define EXYNOS_IRAM_SECONDARY_BASE      0x02020018
 201
 202 /* Enable FIT support and comparison */
 203 #define CONFIG_FIT
 204 #define CONFIG_FIT_BEST_MATCH
 205
 206 #endif  /* __CONFIG_EXYNOS5_COMMON_H */