include/configs/gr_ep2s60.h

   1 /* Configuration header file for Gaisler Research AB's Template
   2  * design (GPL Open Source SPARC/LEON3 96MHz) for Altera NIOS
   3  * Development board Stratix II edition, with the FPGA device
   4  * EP2S60.
   5  *
   6  * (C) Copyright 2003-2005
   7  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   8  *
   9  * (C) Copyright 2008
  10  * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
  11  *
  12  * SPDX-License-Identifier:     GPL-2.0+
  13  */
  14
  15 #ifndef __CONFIG_H__
  16 #define __CONFIG_H__
  17
  18 /*
  19  * High Level Configuration Options
  20  * (easy to change)
  21  */
  22
  23 /* Altera NIOS Development board, Stratix II board */
  24 #define CONFIG_GR_EP2S60        1
  25
  26 /* CPU / AMBA BUS configuration */
  27 #define CONFIG_SYS_CLK_FREQ     96000000        /* 96MHz */
  28
  29 /* Number of SPARC register windows */
  30 #define CONFIG_SYS_SPARC_NWINDOWS 8
  31
  32 /* Define this is the GR-2S60-MEZZ mezzanine is available and you
  33  * want to use the USB and GRETH functionality of the board
  34  */
  35 #undef GR_2S60_MEZZ
  36
  37 #ifdef GR_2S60_MEZZ
  38 #define USE_GRETH 1
  39 #define USE_GRUSB 1
  40 #endif
  41
  42 /*
  43  * Serial console configuration
  44  */
  45 #define CONFIG_BAUDRATE         38400   /* ... at 38400 bps */
  46 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  47
  48 /* Partitions */
  49 #define CONFIG_DOS_PARTITION
  50 #define CONFIG_MAC_PARTITION
  51 #define CONFIG_ISO_PARTITION
  52
  53 /*
  54  * Supported commands
  55  */
  56 #define CONFIG_CMD_REGINFO
  57 #define CONFIG_CMD_PING
  58 #define CONFIG_CMD_DIAG
  59 #define CONFIG_CMD_IRQ
  60
  61 /* USB support */
  62 #if USE_GRUSB
  63 #define CONFIG_USB_UHCI
  64 #define CONFIG_CMD_FAT
  65 #define CONFIG_CMD_EXT2
  66 #define CONFIG_CMD_USB
  67 #define CONFIG_USB_STORAGE
  68 /* Enable needed helper functions */
  69 #define CONFIG_SYS_STDIO_DEREGISTER     /* needs stdio_deregister */
  70 #endif
  71
  72 /*
  73  * Autobooting
  74  */
  75 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
  76
  77 #define CONFIG_PREBOOT  "echo;" \
  78         "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
  79         "echo"
  80
  81 #undef  CONFIG_BOOTARGS
  82
  83 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  84         "netdev=eth0\0"                                                 \
  85         "nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw " \
  86                 "nfsroot=${serverip}:${rootpath}\0"                     \
  87         "ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"                  \
  88         "addip=setenv bootargs ${bootargs} "                            \
  89                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  90                 ":${hostname}:${netdev}:off panic=1\0"                  \
  91         "flash_nfs=run nfsargs addip;"                                  \
  92                 "bootm ${kernel_addr}\0"                                \
  93         "flash_self=run ramargs addip;"                                 \
  94                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  95         "net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"   \
  96         "scratch=40800000\0"                                    \
  97         "getkernel=tftpboot $(scratch) $(bootfile)\0" \
  98         "bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.207:192.168.0.20:192.168.0.1:255.255.255.0:ml401:eth0\0" \
  99         ""
 100
 101 #define CONFIG_NETMASK 255.255.255.0
 102 #define CONFIG_GATEWAYIP 192.168.0.1
 103 #define CONFIG_SERVERIP 192.168.0.20
 104 #define CONFIG_IPADDR 192.168.0.207
 105 #define CONFIG_ROOTPATH "/export/rootfs"
 106 #define CONFIG_HOSTNAME  ml401
 107 #define CONFIG_BOOTFILE "/uImage"
 108
 109 #define CONFIG_BOOTCOMMAND      "run flash_self"
 110
 111 /* Memory MAP
 112  *
 113  *  Flash:
 114  *  |--------------------------------|
 115  *  | 0x00000000 Text & Data & BSS   | *
 116  *  |            for Monitor         | *
 117  *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
 118  *  | UNUSED / Growth                | * 256kb
 119  *  |--------------------------------|
 120  *  | 0x00050000 Base custom area    | *
 121  *  |            kernel / FS         | *
 122  *  |                                | * Rest of Flash
 123  *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
 124  *  | END-0x00008000 Environment     | * 32kb
 125  *  |--------------------------------|
 126  *
 127  *
 128  *
 129  *  Main Memory:
 130  *  |--------------------------------|
 131  *  | UNUSED / scratch area          |
 132  *  |                                |
 133  *  |                                |
 134  *  |                                |
 135  *  |                                |
 136  *  |--------------------------------|
 137  *  | Monitor .Text / .DATA / .BSS   | * 512kb
 138  *  | Relocated!                     | *
 139  *  |--------------------------------|
 140  *  | Monitor Malloc                 | * 128kb (contains relocated environment)
 141  *  |--------------------------------|
 142  *  | Monitor/kernel STACK           | * 64kb
 143  *  |--------------------------------|
 144  *  | Page Table for MMU systems     | * 2k
 145  *  |--------------------------------|
 146  *  | PROM Code accessed from Linux  | * 6kb-128b
 147  *  |--------------------------------|
 148  *  | Global data (avail from kernel)| * 128b
 149  *  |--------------------------------|
 150  *
 151  */
 152
 153 /*
 154  * Flash configuration (8,16 or 32 MB)
 155  * TEXT base always at 0xFFF00000
 156  * ENV_ADDR always at  0xFFF40000
 157  * FLASH_BASE at 0xFC000000 for 64 MB
 158  *               0xFE000000 for 32 MB
 159  *               0xFF000000 for 16 MB
 160  *               0xFF800000 for  8 MB
 161  */
 162 /*#define CONFIG_SYS_NO_FLASH           1*/
 163 #define CONFIG_SYS_FLASH_BASE           0x00000000
 164 #define CONFIG_SYS_FLASH_SIZE           0x00400000      /* FPGA Bit file is in top of FLASH, we only ues the bottom 4Mb */
 165
 166 #define PHYS_FLASH_SECT_SIZE    0x00010000      /* 64 KB sectors */
 167 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max num of sects on one chip */
 168 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
 169
 170 #define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 171 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 172 #define CONFIG_SYS_FLASH_LOCK_TOUT      5       /* Timeout for Flash Set Lock Bit (in ms) */
 173 #define CONFIG_SYS_FLASH_UNLOCK_TOUT    10000   /* Timeout for Flash Clear Lock Bits (in ms) */
 174 #define CONFIG_SYS_FLASH_PROTECTION     /* "Real" (hardware) sectors protection */
 175
 176 /*** CFI CONFIG ***/
 177 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 178 #define CONFIG_FLASH_CFI_DRIVER
 179 #define CONFIG_SYS_FLASH_CFI
 180 /* Bypass cache when reading regs from flash memory */
 181 #define CONFIG_SYS_FLASH_CFI_BYPASS_READ
 182 /* Buffered writes (32byte/go) instead of single accesses */
 183 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 184
 185 /*
 186  * Environment settings
 187  */
 188 /*#define CONFIG_ENV_IS_NOWHERE 1*/
 189 #define CONFIG_ENV_IS_IN_FLASH  1
 190 /* CONFIG_ENV_ADDR need to be at sector boundary */
 191 #define CONFIG_ENV_SIZE         0x8000
 192 #define CONFIG_ENV_SECT_SIZE    0x20000
 193 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
 194 #define CONFIG_ENV_OVERWRITE    1
 195
 196 /*
 197  * Memory map
 198  */
 199 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 200 #define CONFIG_SYS_SDRAM_SIZE           0x02000000
 201 #define CONFIG_SYS_SDRAM_END            (CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
 202
 203 /* no SRAM available */
 204 #undef CONFIG_SYS_SRAM_BASE
 205 #undef CONFIG_SYS_SRAM_SIZE
 206
 207 #define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
 208 #define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
 209 #define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
 210
 211 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_SDRAM_END - GENERATED_GBL_DATA_SIZE)
 212
 213 #define CONFIG_SYS_PROM_SIZE            (8192-GENERATED_GBL_DATA_SIZE)
 214 #define CONFIG_SYS_PROM_OFFSET          (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
 215
 216 #define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_PROM_OFFSET-32)
 217 #define CONFIG_SYS_STACK_SIZE           (0x10000-32)
 218
 219 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 220 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 221 #   define CONFIG_SYS_RAMBOOT           1
 222 #endif
 223
 224 #define CONFIG_SYS_MONITOR_LEN          (512 << 10)     /* Reserve 512 kB for Monitor   */
 225 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 226 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 227
 228 #define CONFIG_SYS_MALLOC_END           (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
 229 #define CONFIG_SYS_MALLOC_BASE          (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
 230
 231 /* relocated monitor area */
 232 #define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
 233 #define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
 234
 235 /* make un relocated address from relocated address */
 236 #define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
 237
 238 /*
 239  * Ethernet configuration uses on board SMC91C111, however if a mezzanine
 240  * with a PHY is attached the GRETH can be used on this board.
 241  * Define USE_GRETH in order to use the mezzanine provided PHY with the
 242  * onchip GRETH network MAC, note that this is not supported by the
 243  * template design.
 244  */
 245 #ifndef USE_GRETH
 246
 247 /* USE SMC91C111 MAC */
 248 #define CONFIG_SMC91111          1
 249 #define CONFIG_SMC91111_BASE            0x20000300      /* chip select 3         */
 250 #define CONFIG_SMC_USE_32_BIT           1       /* 32 bit bus  */
 251 #undef  CONFIG_SMC_91111_EXT_PHY        /* we use internal phy   */
 252 /*#define CONFIG_SHOW_ACTIVITY*/
 253 #define CONFIG_NET_RETRY_COUNT          10      /* # of retries          */
 254
 255 #else
 256
 257 /* USE GRETH Ethernet Driver */
 258 #define CONFIG_GRETH    1
 259 #endif
 260
 261 #define CONFIG_PHY_ADDR  0x00
 262
 263 /*
 264  * Miscellaneous configurable options
 265  */
 266 #define CONFIG_SYS_LONGHELP             /* undef to save memory     */
 267 #if defined(CONFIG_CMD_KGDB)
 268 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 269 #else
 270 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 271 #endif
 272 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 273 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 274 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 275
 276 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 277 #define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 278
 279 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 280
 281 /*-----------------------------------------------------------------------
 282  * USB stuff
 283  *-----------------------------------------------------------------------
 284  */
 285 #define CONFIG_USB_CLOCK        0x0001BBBB
 286 #define CONFIG_USB_CONFIG       0x00005000
 287
 288 /***** Gaisler GRLIB IP-Cores Config ********/
 289
 290 #define CONFIG_SYS_GRLIB_SDRAM    0
 291
 292 /* See, GRLIB Docs (grip.pdf) on how to set up
 293  * These the memory controller registers.
 294  */
 295 #define CONFIG_SYS_GRLIB_MEMCFG1  (0x10f800ff | (1<<11))
 296 #define CONFIG_SYS_GRLIB_MEMCFG2  0x00000000
 297 #define CONFIG_SYS_GRLIB_MEMCFG3  0x00000000
 298
 299 #define CONFIG_SYS_GRLIB_FT_MEMCFG1  (0x10f800ff | (1<<11))
 300 #define CONFIG_SYS_GRLIB_FT_MEMCFG2  0x00000000
 301 #define CONFIG_SYS_GRLIB_FT_MEMCFG3  0x00000000
 302
 303 #define CONFIG_SYS_GRLIB_DDR_CFG  0xa900830a
 304
 305 #define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
 306 #define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
 307
 308 /* Identification string */
 309 #define CONFIG_IDENT_STRING "GAISLER LEON3 EP2S60"
 310
 311 /* default kernel command line */
 312 #define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
 313
 314 #endif                          /* __CONFIG_H */