include/configs/hrcon.h

   1 /*
   2  * (C) Copyright 2014
   3  * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
   4  *
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15 #define CONFIG_E300             1 /* E300 family */
  16 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  17 #define CONFIG_MPC830x          1 /* MPC830x family */
  18 #define CONFIG_MPC8308          1 /* MPC8308 CPU specific */
  19 #define CONFIG_HRCON            1 /* HRCON board specific */
  20
  21 #define CONFIG_SYS_TEXT_BASE    0xFE000000
  22
  23 #ifdef CONFIG_HRCON_DH
  24 #define CONFIG_IDENT_STRING     " hrcon dh 0.01"
  25 #else
  26 #define CONFIG_IDENT_STRING     " hrcon 0.01"
  27 #endif
  28
  29 #define CONFIG_BOARD_EARLY_INIT_F
  30 #define CONFIG_BOARD_EARLY_INIT_R
  31 #define CONFIG_LAST_STAGE_INIT
  32
  33 #define CONFIG_MMC
  34 #define CONFIG_FSL_ESDHC
  35 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
  36 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
  37
  38 #define CONFIG_GENERIC_MMC
  39 #define CONFIG_DOS_PARTITION
  40
  41 #define CONFIG_CMD_FPGAD
  42 #define CONFIG_CMD_IOLOOP
  43
  44 /*
  45  * System Clock Setup
  46  */
  47 #define CONFIG_83XX_CLKIN       33333333 /* in Hz */
  48 #define CONFIG_SYS_CLK_FREQ     CONFIG_83XX_CLKIN
  49
  50 /*
  51  * Hardware Reset Configuration Word
  52  * if CLKIN is 66.66MHz, then
  53  * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz
  54  * We choose the A type silicon as default, so the core is 400Mhz.
  55  */
  56 #define CONFIG_SYS_HRCW_LOW (\
  57         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  58         HRCWL_DDR_TO_SCB_CLK_2X1 |\
  59         HRCWL_SVCOD_DIV_2 |\
  60         HRCWL_CSB_TO_CLKIN_4X1 |\
  61         HRCWL_CORE_TO_CSB_3X1)
  62 /*
  63  * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits
  64  * in 8308's HRCWH according to the manual, but original Freescale's
  65  * code has them and I've expirienced some problems using the board
  66  * with BDI3000 attached when I've tried to set these bits to zero
  67  * (UART doesn't work after the 'reset run' command).
  68  */
  69 #define CONFIG_SYS_HRCW_HIGH (\
  70         HRCWH_PCI_HOST |\
  71         HRCWH_PCI1_ARBITER_ENABLE |\
  72         HRCWH_CORE_ENABLE |\
  73         HRCWH_FROM_0XFFF00100 |\
  74         HRCWH_BOOTSEQ_DISABLE |\
  75         HRCWH_SW_WATCHDOG_DISABLE |\
  76         HRCWH_ROM_LOC_LOCAL_16BIT |\
  77         HRCWH_RL_EXT_LEGACY |\
  78         HRCWH_TSEC1M_IN_RGMII |\
  79         HRCWH_TSEC2M_IN_RGMII |\
  80         HRCWH_BIG_ENDIAN)
  81
  82 /*
  83  * System IO Config
  84  */
  85 #define CONFIG_SYS_SICRH (\
  86         SICRH_ESDHC_A_SD |\
  87         SICRH_ESDHC_B_SD |\
  88         SICRH_ESDHC_C_SD |\
  89         SICRH_GPIO_A_GPIO |\
  90         SICRH_GPIO_B_GPIO |\
  91         SICRH_IEEE1588_A_GPIO |\
  92         SICRH_USB |\
  93         SICRH_GTM_GPIO |\
  94         SICRH_IEEE1588_B_GPIO |\
  95         SICRH_ETSEC2_GPIO |\
  96         SICRH_GPIOSEL_1 |\
  97         SICRH_TMROBI_V3P3 |\
  98         SICRH_TSOBI1_V2P5 |\
  99         SICRH_TSOBI2_V2P5)      /* 0x0037f103 */
 100 #define CONFIG_SYS_SICRL (\
 101         SICRL_SPI_PF0 |\
 102         SICRL_UART_PF0 |\
 103         SICRL_IRQ_PF0 |\
 104         SICRL_I2C2_PF0 |\
 105         SICRL_ETSEC1_GTX_CLK125)        /* 0x00000000 */
 106
 107 /*
 108  * IMMR new address
 109  */
 110 #define CONFIG_SYS_IMMR         0xE0000000
 111
 112 /*
 113  * SERDES
 114  */
 115 #define CONFIG_FSL_SERDES
 116 #define CONFIG_FSL_SERDES1      0xe3000
 117
 118 /*
 119  * Arbiter Setup
 120  */
 121 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */
 122 #define CONFIG_SYS_ACR_RPTCNT   3 /* Arbiter repeat count is 4 */
 123 #define CONFIG_SYS_SPCR_TSECEP  3 /* eTSEC emergency priority is highest */
 124
 125 /*
 126  * DDR Setup
 127  */
 128 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
 129 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
 130 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
 131 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 132 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
 133                                 | DDRCDR_PZ_LOZ \
 134                                 | DDRCDR_NZ_LOZ \
 135                                 | DDRCDR_ODT \
 136                                 | DDRCDR_Q_DRN)
 137                                 /* 0x7b880001 */
 138 /*
 139  * Manually set up DDR parameters
 140  * consist of one chip NT5TU64M16HG from NANYA
 141  */
 142
 143 #define CONFIG_SYS_DDR_SIZE             128 /* MB */
 144
 145 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
 146 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
 147                                 | CSCONFIG_ODT_RD_NEVER \
 148                                 | CSCONFIG_ODT_WR_ONLY_CURRENT \
 149                                 | CSCONFIG_BANK_BIT_3 \
 150                                 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
 151                                 /* 0x80010102 */
 152 #define CONFIG_SYS_DDR_TIMING_3 0
 153 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
 154                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
 155                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 156                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 157                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 158                                 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 159                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 160                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 161                                 /* 0x00260802 */
 162 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
 163                                 | (6 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 164                                 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \
 165                                 | (7 << TIMING_CFG1_CASLAT_SHIFT) \
 166                                 | (9 << TIMING_CFG1_REFREC_SHIFT) \
 167                                 | (2 << TIMING_CFG1_WRREC_SHIFT) \
 168                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 169                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 170                                 /* 0x26279222 */
 171 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
 172                                 | (4 << TIMING_CFG2_CPO_SHIFT) \
 173                                 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 174                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 175                                 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 176                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 177                                 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
 178                                 /* 0x021848c5 */
 179 #define CONFIG_SYS_DDR_INTERVAL ((0x0824 << SDRAM_INTERVAL_REFINT_SHIFT) \
 180                                 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 181                                 /* 0x08240100 */
 182 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 183                                 | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 184                                 | SDRAM_CFG_DBW_16)
 185                                 /* 0x43100000 */
 186
 187 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000 /* 1 posted refresh */
 188 #define CONFIG_SYS_DDR_MODE             ((0x0440 << SDRAM_MODE_ESD_SHIFT) \
 189                                 | (0x0242 << SDRAM_MODE_SD_SHIFT))
 190                                 /* ODT 150ohm CL=4, AL=0 on SDRAM */
 191 #define CONFIG_SYS_DDR_MODE2            0x00000000
 192
 193 /*
 194  * Memory test
 195  */
 196 #define CONFIG_SYS_MEMTEST_START        0x00001000 /* memtest region */
 197 #define CONFIG_SYS_MEMTEST_END          0x07f00000
 198
 199 /*
 200  * The reserved memory
 201  */
 202 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 203
 204 #define CONFIG_SYS_MONITOR_LEN  (384 * 1024) /* Reserve 384 kB for Mon */
 205 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 206
 207 /*
 208  * Initial RAM Base Address Setup
 209  */
 210 #define CONFIG_SYS_INIT_RAM_LOCK        1
 211 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 212 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 213 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 214         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 215
 216 /*
 217  * Local Bus Configuration & Clock Setup
 218  */
 219 #define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
 220 #define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
 221 #define CONFIG_SYS_LBC_LBCR             0x00040000
 222
 223 /*
 224  * FLASH on the Local Bus
 225  */
 226 #if 1
 227 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 228 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 229 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
 230 #define CONFIG_FLASH_CFI_LEGACY
 231 #define CONFIG_SYS_FLASH_LEGACY_512Kx16
 232 #else
 233 #define CONFIG_SYS_NO_FLASH
 234 #endif
 235
 236 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 237 #define CONFIG_SYS_FLASH_SIZE           8 /* FLASH size is up to 8M */
 238 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use h/w Flash protection. */
 239
 240 /* Window base at flash base */
 241 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 242 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)
 243
 244 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 245                                 | BR_PS_16      /* 16 bit port */ \
 246                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 247                                 | BR_V)         /* valid */
 248 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
 249                                 | OR_UPM_XAM \
 250                                 | OR_GPCM_CSNT \
 251                                 | OR_GPCM_ACS_DIV2 \
 252                                 | OR_GPCM_XACS \
 253                                 | OR_GPCM_SCY_15 \
 254                                 | OR_GPCM_TRLX_SET \
 255                                 | OR_GPCM_EHTR_SET)
 256
 257 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 258 #define CONFIG_SYS_MAX_FLASH_SECT       135
 259
 260 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000 /* Flash Erase Timeout (ms) */
 261 #define CONFIG_SYS_FLASH_WRITE_TOUT     500 /* Flash Write Timeout (ms) */
 262
 263 /*
 264  * FPGA
 265  */
 266 #define CONFIG_SYS_FPGA0_BASE           0xE0600000
 267 #define CONFIG_SYS_FPGA0_SIZE           1 /* FPGA size is 1M */
 268
 269 /* Window base at FPGA base */
 270 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_FPGA0_BASE
 271 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_1MB)
 272
 273 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_FPGA0_BASE \
 274                                 | BR_PS_16      /* 16 bit port */ \
 275                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 276                                 | BR_V)         /* valid */
 277 #define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_FPGA0_SIZE) \
 278                                 | OR_UPM_XAM \
 279                                 | OR_GPCM_CSNT \
 280                                 | OR_GPCM_ACS_DIV2 \
 281                                 | OR_GPCM_XACS \
 282                                 | OR_GPCM_SCY_15 \
 283                                 | OR_GPCM_TRLX_SET \
 284                                 | OR_GPCM_EHTR_SET)
 285
 286 #define CONFIG_SYS_FPGA_BASE(k)         CONFIG_SYS_FPGA0_BASE
 287 #define CONFIG_SYS_FPGA_DONE(k)         0x0010
 288
 289 #define CONFIG_SYS_FPGA_COUNT           1
 290
 291 #define CONFIG_SYS_MCLINK_MAX           3
 292
 293 #define CONFIG_SYS_FPGA_PTR \
 294         { (struct ihs_fpga *)CONFIG_SYS_FPGA0_BASE, NULL, NULL, NULL }
 295
 296 /*
 297  * Serial Port
 298  */
 299 #define CONFIG_CONS_INDEX       2
 300 #define CONFIG_SYS_NS16550_SERIAL
 301 #define CONFIG_SYS_NS16550_REG_SIZE     1
 302 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 303
 304 #define CONFIG_SYS_BAUDRATE_TABLE  \
 305         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 306
 307 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
 308 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
 309
 310 /* Pass open firmware flat tree */
 311
 312 /* I2C */
 313 #define CONFIG_SYS_I2C
 314 #define CONFIG_SYS_I2C_FSL
 315 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 316 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 317 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 318
 319 #define CONFIG_PCA953X                  /* NXP PCA9554 */
 320 #define CONFIG_PCA9698                  /* NXP PCA9698 */
 321
 322 #define CONFIG_SYS_I2C_IHS
 323 #define CONFIG_SYS_I2C_IHS_CH0
 324 #define CONFIG_SYS_I2C_IHS_SPEED_0              50000
 325 #define CONFIG_SYS_I2C_IHS_SLAVE_0              0x7F
 326 #define CONFIG_SYS_I2C_IHS_CH1
 327 #define CONFIG_SYS_I2C_IHS_SPEED_1              50000
 328 #define CONFIG_SYS_I2C_IHS_SLAVE_1              0x7F
 329 #define CONFIG_SYS_I2C_IHS_CH2
 330 #define CONFIG_SYS_I2C_IHS_SPEED_2              50000
 331 #define CONFIG_SYS_I2C_IHS_SLAVE_2              0x7F
 332 #define CONFIG_SYS_I2C_IHS_CH3
 333 #define CONFIG_SYS_I2C_IHS_SPEED_3              50000
 334 #define CONFIG_SYS_I2C_IHS_SLAVE_3              0x7F
 335
 336 #ifdef CONFIG_HRCON_DH
 337 #define CONFIG_SYS_I2C_IHS_DUAL
 338 #define CONFIG_SYS_I2C_IHS_CH0_1
 339 #define CONFIG_SYS_I2C_IHS_SPEED_0_1            50000
 340 #define CONFIG_SYS_I2C_IHS_SLAVE_0_1            0x7F
 341 #define CONFIG_SYS_I2C_IHS_CH1_1
 342 #define CONFIG_SYS_I2C_IHS_SPEED_1_1            50000
 343 #define CONFIG_SYS_I2C_IHS_SLAVE_1_1            0x7F
 344 #define CONFIG_SYS_I2C_IHS_CH2_1
 345 #define CONFIG_SYS_I2C_IHS_SPEED_2_1            50000
 346 #define CONFIG_SYS_I2C_IHS_SLAVE_2_1            0x7F
 347 #define CONFIG_SYS_I2C_IHS_CH3_1
 348 #define CONFIG_SYS_I2C_IHS_SPEED_3_1            50000
 349 #define CONFIG_SYS_I2C_IHS_SLAVE_3_1            0x7F
 350 #endif
 351
 352 /*
 353  * Software (bit-bang) I2C driver configuration
 354  */
 355 #define CONFIG_SYS_I2C_SOFT
 356 #define CONFIG_SYS_I2C_SOFT_SPEED               50000
 357 #define CONFIG_SYS_I2C_SOFT_SLAVE               0x7F
 358 #define I2C_SOFT_DECLARATIONS2
 359 #define CONFIG_SYS_I2C_SOFT_SPEED_2             50000
 360 #define CONFIG_SYS_I2C_SOFT_SLAVE_2             0x7F
 361 #define I2C_SOFT_DECLARATIONS3
 362 #define CONFIG_SYS_I2C_SOFT_SPEED_3             50000
 363 #define CONFIG_SYS_I2C_SOFT_SLAVE_3             0x7F
 364 #define I2C_SOFT_DECLARATIONS4
 365 #define CONFIG_SYS_I2C_SOFT_SPEED_4             50000
 366 #define CONFIG_SYS_I2C_SOFT_SLAVE_4             0x7F
 367 #define I2C_SOFT_DECLARATIONS5
 368 #define CONFIG_SYS_I2C_SOFT_SPEED_5             50000
 369 #define CONFIG_SYS_I2C_SOFT_SLAVE_5             0x7F
 370 #define I2C_SOFT_DECLARATIONS6
 371 #define CONFIG_SYS_I2C_SOFT_SPEED_6             50000
 372 #define CONFIG_SYS_I2C_SOFT_SLAVE_6             0x7F
 373 #define I2C_SOFT_DECLARATIONS7
 374 #define CONFIG_SYS_I2C_SOFT_SPEED_7             50000
 375 #define CONFIG_SYS_I2C_SOFT_SLAVE_7             0x7F
 376 #define I2C_SOFT_DECLARATIONS8
 377 #define CONFIG_SYS_I2C_SOFT_SPEED_8             50000
 378 #define CONFIG_SYS_I2C_SOFT_SLAVE_8             0x7F
 379
 380 #ifdef CONFIG_HRCON_DH
 381 #define I2C_SOFT_DECLARATIONS9
 382 #define CONFIG_SYS_I2C_SOFT_SPEED_9             50000
 383 #define CONFIG_SYS_I2C_SOFT_SLAVE_9             0x7F
 384 #define I2C_SOFT_DECLARATIONS10
 385 #define CONFIG_SYS_I2C_SOFT_SPEED_10            50000
 386 #define CONFIG_SYS_I2C_SOFT_SLAVE_10            0x7F
 387 #define I2C_SOFT_DECLARATIONS11
 388 #define CONFIG_SYS_I2C_SOFT_SPEED_11            50000
 389 #define CONFIG_SYS_I2C_SOFT_SLAVE_11            0x7F
 390 #define I2C_SOFT_DECLARATIONS12
 391 #define CONFIG_SYS_I2C_SOFT_SPEED_12            50000
 392 #define CONFIG_SYS_I2C_SOFT_SLAVE_12            0x7F
 393 #endif
 394
 395 #ifdef CONFIG_HRCON_DH
 396 #define CONFIG_SYS_ICS8N3QV01_I2C               {13, 14, 15, 16, 17, 18, 19, 20}
 397 #define CONFIG_SYS_DP501_I2C                    {1, 3, 5, 7, 2, 4, 6, 8}
 398 #define CONFIG_HRCON_FANS                       { {10, 0x4c}, {11, 0x4c}, \
 399                                                   {12, 0x4c} }
 400 #else
 401 #define CONFIG_SYS_ICS8N3QV01_I2C               {9, 10, 11, 12}
 402 #define CONFIG_SYS_DP501_I2C                    {1, 2, 3, 4}
 403 #define CONFIG_HRCON_FANS                       { {6, 0x4c}, {7, 0x4c}, \
 404                                                   {8, 0x4c} }
 405 #endif
 406
 407 #ifndef __ASSEMBLY__
 408 void fpga_gpio_set(unsigned int bus, int pin);
 409 void fpga_gpio_clear(unsigned int bus, int pin);
 410 int fpga_gpio_get(unsigned int bus, int pin);
 411 void fpga_control_set(unsigned int bus, int pin);
 412 void fpga_control_clear(unsigned int bus, int pin);
 413 #endif
 414
 415 #define I2C_SDA_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0040 : 0x0200)
 416 #define I2C_SCL_GPIO    ((I2C_ADAP_HWNR > 3) ? 0x0020 : 0x0100)
 417 #define I2C_FPGA_IDX    (I2C_ADAP_HWNR % 4)
 418
 419 #ifdef CONFIG_HRCON_DH
 420 #define I2C_ACTIVE \
 421         do { \
 422                 if (I2C_ADAP_HWNR > 7) \
 423                         fpga_control_set(I2C_FPGA_IDX, 0x0004); \
 424                 else \
 425                         fpga_control_clear(I2C_FPGA_IDX, 0x0004); \
 426         } while (0)
 427 #else
 428 #define I2C_ACTIVE      { }
 429 #endif
 430 #define I2C_TRISTATE    { }
 431 #define I2C_READ \
 432         (fpga_gpio_get(I2C_FPGA_IDX, I2C_SDA_GPIO) ? 1 : 0)
 433 #define I2C_SDA(bit) \
 434         do { \
 435                 if (bit) \
 436                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 437                 else \
 438                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SDA_GPIO); \
 439         } while (0)
 440 #define I2C_SCL(bit) \
 441         do { \
 442                 if (bit) \
 443                         fpga_gpio_set(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 444                 else \
 445                         fpga_gpio_clear(I2C_FPGA_IDX, I2C_SCL_GPIO); \
 446         } while (0)
 447 #define I2C_DELAY       udelay(25)      /* 1/4 I2C clock duration */
 448
 449 /*
 450  * Software (bit-bang) MII driver configuration
 451  */
 452 #define CONFIG_BITBANGMII               /* bit-bang MII PHY management */
 453 #define CONFIG_BITBANGMII_MULTI
 454
 455 /*
 456  * OSD Setup
 457  */
 458 #define CONFIG_SYS_OSD_SCREENS          1
 459 #define CONFIG_SYS_DP501_DIFFERENTIAL
 460 #define CONFIG_SYS_DP501_VCAPCTRL0      0x01 /* DDR mode 0, DE for H/VSYNC */
 461
 462 #ifdef CONFIG_HRCON_DH
 463 #define CONFIG_SYS_OSD_DH
 464 #endif
 465
 466 /*
 467  * General PCI
 468  * Addresses are mapped 1-1.
 469  */
 470 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 471 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA0000000
 472 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA0000000
 473 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 474 #define CONFIG_SYS_PCIE1_CFG_BASE       0xB0000000
 475 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x01000000
 476 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 477 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB1000000
 478 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 479
 480 /* enable PCIE clock */
 481 #define CONFIG_SYS_SCCR_PCIEXP1CM       1
 482
 483 #define CONFIG_PCI
 484 #define CONFIG_PCI_INDIRECT_BRIDGE
 485 #define CONFIG_PCIE
 486
 487 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 488
 489 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 490 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
 491
 492 /*
 493  * TSEC
 494  */
 495 #define CONFIG_TSEC_ENET        /* TSEC ethernet support */
 496 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 497 #define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 498
 499 /*
 500  * TSEC ethernet configuration
 501  */
 502 #define CONFIG_MII              1 /* MII PHY management */
 503 #define CONFIG_TSEC1
 504 #define CONFIG_TSEC1_NAME       "eTSEC0"
 505 #define TSEC1_PHY_ADDR          1
 506 #define TSEC1_PHYIDX            0
 507 #define TSEC1_FLAGS             TSEC_GIGABIT
 508
 509 /* Options are: eTSEC[0-1] */
 510 #define CONFIG_ETHPRIME         "eTSEC0"
 511
 512 /*
 513  * Environment
 514  */
 515 #if 1
 516 #define CONFIG_ENV_IS_IN_FLASH  1
 517 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 518                                  CONFIG_SYS_MONITOR_LEN)
 519 #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K(one sector) for env */
 520 #define CONFIG_ENV_SIZE         0x2000
 521 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 522 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 523 #else
 524 #define CONFIG_ENV_IS_NOWHERE
 525 #define CONFIG_ENV_SIZE         0x2000          /* 8KB */
 526 #endif
 527
 528 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 529 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 530
 531 /*
 532  * Command line configuration.
 533  */
 534 #define CONFIG_CMD_PCI
 535
 536 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 537 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support */
 538
 539 /*
 540  * Miscellaneous configurable options
 541  */
 542 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 543 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 544 #define CONFIG_SYS_HZ           1000    /* decrementer freq: 1ms ticks */
 545
 546 #undef CONFIG_ZERO_BOOTDELAY_CHECK      /* ignore keypress on bootdelay==0 */
 547
 548 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 549
 550 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 551
 552 /* Print Buffer Size */
 553 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 554 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 555 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 556
 557 /*
 558  * For booting Linux, the board info and command line data
 559  * have to be in the first 256 MB of memory, since this is
 560  * the maximum mapped by the Linux kernel during initialization.
 561  */
 562 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 563
 564 /*
 565  * Core HID Setup
 566  */
 567 #define CONFIG_SYS_HID0_INIT    0x000000000
 568 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 569                                  HID0_ENABLE_INSTRUCTION_CACHE | \
 570                                  HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
 571 #define CONFIG_SYS_HID2         HID2_HBE
 572
 573 /*
 574  * MMU Setup
 575  */
 576
 577 /* DDR: cache cacheable */
 578 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 579                                         BATL_MEMCOHERENCE)
 580 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \
 581                                         BATU_VS | BATU_VP)
 582 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 583 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 584
 585 /* IMMRBAR, PCI IO and FPGA: cache-inhibit and guarded */
 586 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 587                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 588 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \
 589                                         BATU_VP)
 590 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 591 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 592
 593 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 594 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 595                                         BATL_MEMCOHERENCE)
 596 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \
 597                                         BATU_VS | BATU_VP)
 598 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 599                                         BATL_CACHEINHIBIT | \
 600                                         BATL_GUARDEDSTORAGE)
 601 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 602
 603 /* Stack in dcache: cacheable, no memory coherence */
 604 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 605 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 606                                         BATU_VS | BATU_VP)
 607 #define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
 608 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 609
 610 /*
 611  * Environment Configuration
 612  */
 613
 614 #define CONFIG_ENV_OVERWRITE
 615
 616 #if defined(CONFIG_TSEC_ENET)
 617 #define CONFIG_HAS_ETH0
 618 #endif
 619
 620 #define CONFIG_BAUDRATE 115200
 621
 622 #define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */
 623
 624 #define CONFIG_BOOTDELAY        5       /* -1 disables auto-boot */
 625
 626 #define CONFIG_HOSTNAME         hrcon
 627 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 628 #define CONFIG_BOOTFILE         "uImage"
 629
 630 #define CONFIG_PREBOOT          /* enable preboot variable */
 631
 632 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 633         "netdev=eth0\0"                                                 \
 634         "consoledev=ttyS1\0"                                            \
 635         "u-boot=u-boot.bin\0"                                           \
 636         "kernel_addr=1000000\0"                                 \
 637         "fdt_addr=C00000\0"                                             \
 638         "fdtfile=hrcon.dtb\0"                           \
 639         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 640         "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE)      \
 641                 " +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
 642                 " +${filesize};cp.b ${fileaddr} "                       \
 643                 __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0"   \
 644         "upd=run load update\0"                                         \
 645
 646 #define CONFIG_NFSBOOTCOMMAND                                           \
 647         "setenv bootargs root=/dev/nfs rw "                             \
 648         "nfsroot=$serverip:$rootpath "                                  \
 649         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 650         "console=$consoledev,$baudrate $othbootargs;"                   \
 651         "tftp ${kernel_addr} $bootfile;"                                \
 652         "tftp ${fdt_addr} $fdtfile;"                                    \
 653         "bootm ${kernel_addr} - ${fdt_addr}"
 654
 655 #define CONFIG_MMCBOOTCOMMAND                                           \
 656         "setenv bootargs root=/dev/mmcblk0p3 rw rootwait "              \
 657         "console=$consoledev,$baudrate $othbootargs;"                   \
 658         "ext2load mmc 0:2 ${kernel_addr} $bootfile;"                    \
 659         "ext2load mmc 0:2 ${fdt_addr} $fdtfile;"                        \
 660         "bootm ${kernel_addr} - ${fdt_addr}"
 661
 662 #define CONFIG_BOOTCOMMAND              CONFIG_MMCBOOTCOMMAND
 663
 664 #endif  /* __CONFIG_H */