include/configs/jupiter.h

   1 /*
   2  * (C) Copyright 2007
   3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 /*
  12  * High Level Configuration Options
  13  * (easy to change)
  14  */
  15
  16 #define CONFIG_MPC5xxx          1       /* This is an MPC5xxx CPU */
  17 #define CONFIG_MPC5200          1       /* especially an MPC5200 */
  18 #define CONFIG_JUPITER          1       /* ... on Jupiter board */
  19
  20 /*
  21  * Valid values for CONFIG_SYS_TEXT_BASE are:
  22  * 0xFFF00000   boot high (standard configuration)
  23  * 0x00100000   boot from RAM (for testing only)
  24  */
  25 #ifndef CONFIG_SYS_TEXT_BASE
  26 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  27 #endif
  28
  29 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000 /* ... running at 33.000000MHz */
  30
  31 #define CONFIG_BOARD_EARLY_INIT_R       1
  32 #define CONFIG_BOARD_EARLY_INIT_F       1
  33
  34 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  35
  36 /*
  37  * Serial console configuration
  38  */
  39 #define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
  40 #define CONFIG_BAUDRATE         115200  /* ... at 115200 bps */
  41 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  42
  43 /*
  44  * PCI Mapping:
  45  * 0x40000000 - 0x4fffffff - PCI Memory
  46  * 0x50000000 - 0x50ffffff - PCI IO Space
  47  */
  48 /*#define CONFIG_PCI            */
  49
  50 #if defined(CONFIG_PCI)
  51 #define CONFIG_PCI_PNP          1
  52 #define CONFIG_PCI_SCAN_SHOW    1
  53 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
  54
  55 #define CONFIG_PCI_MEM_BUS      0x40000000
  56 #define CONFIG_PCI_MEM_PHYS     CONFIG_PCI_MEM_BUS
  57 #define CONFIG_PCI_MEM_SIZE     0x10000000
  58
  59 #define CONFIG_PCI_IO_BUS       0x50000000
  60 #define CONFIG_PCI_IO_PHYS      CONFIG_PCI_IO_BUS
  61 #define CONFIG_PCI_IO_SIZE      0x01000000
  62 #endif
  63
  64 #define CONFIG_SYS_XLB_PIPELINING       1
  65
  66 #define CONFIG_MII              1
  67 #define CONFIG_SYS_RX_ETH_BUFFER        8  /* use 8 rx buffer on eepro100  */
  68
  69 /* Partitions */
  70 #define CONFIG_MAC_PARTITION
  71 #define CONFIG_DOS_PARTITION
  72 #define CONFIG_ISO_PARTITION
  73
  74 #define CONFIG_TIMESTAMP                /* Print image info with timestamp */
  75
  76
  77 /*
  78  * BOOTP options
  79  */
  80 #define CONFIG_BOOTP_BOOTFILESIZE
  81 #define CONFIG_BOOTP_BOOTPATH
  82 #define CONFIG_BOOTP_GATEWAY
  83 #define CONFIG_BOOTP_HOSTNAME
  84
  85
  86 /*
  87  * Command line configuration.
  88  */
  89 #include <config_cmd_default.h>
  90
  91 #define CONFIG_CMD_NFS
  92 #define CONFIG_CMD_SNTP
  93
  94 #if defined(CONFIG_PCI)
  95 #define CODFIG_CMD_PCI
  96 #endif
  97
  98
  99 /*
 100  * Autobooting
 101  */
 102 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
 103
 104 #define CONFIG_PREBOOT  "echo;" \
 105         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 106         "echo"
 107
 108 #undef  CONFIG_BOOTARGS
 109
 110 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 111         "netdev=eth0\0"                                                 \
 112         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 113                 "nfsroot=${serverip}:${rootpath}\0"                     \
 114         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 115         "addip=setenv bootargs ${bootargs} "                            \
 116                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 117                 ":${hostname}:${netdev}:off panic=1\0"                  \
 118         "flash_nfs=run nfsargs addip addcons;"                          \
 119                 "bootm ${kernel_addr}\0"                                \
 120         "flash_self=run ramargs addip;"                                 \
 121                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 122         "addcons=setenv bootargs ${bootargs} console=${contyp},"        \
 123                 "${baudrate}\0"                                         \
 124         "contyp=ttyS0\0"                                                \
 125         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;"    \
 126                 "bootm\0"                                               \
 127         "rootpath=/opt/eldk/ppc_6xx\0"                                  \
 128         "bootfile=/tftpboot/jupiter/uImage\0"                           \
 129         ""
 130
 131 #define CONFIG_BOOTCOMMAND      "run flash_self"
 132
 133 /*
 134  * IPB Bus clocking configuration.
 135  */
 136 #undef CONFIG_SYS_IPBSPEED_133                  /* define for 133MHz speed */
 137
 138 #if 0
 139 /* pass open firmware flat tree */
 140 #define CONFIG_OF_LIBFDT        1
 141 #define CONFIG_OF_BOARD_SETUP   1
 142
 143 #define OF_CPU                  "PowerPC,5200@0"
 144 #define OF_SOC                  "soc5200@f0000000"
 145 #define OF_TBCLK                (bd->bi_busfreq / 8)
 146 #define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"
 147 #endif
 148
 149 #if 0
 150 /*
 151  * I2C configuration
 152  */
 153 #define CONFIG_HARD_I2C         1       /* I2C with hardware support */
 154 #define CONFIG_SYS_I2C_MODULE           2       /* Select I2C module #1 or #2 */
 155
 156 #define CONFIG_SYS_I2C_SPEED            100000 /* 100 kHz */
 157 #define CONFIG_SYS_I2C_SLAVE            0x7F
 158
 159 /*
 160  * EEPROM configuration
 161  */
 162 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50    /* 1010000x */
 163 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 164 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 165 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   70
 166 #endif
 167
 168 /*
 169  * Flash configuration
 170  */
 171 #define CONFIG_SYS_FLASH_BASE           0xFF000000
 172 #define CONFIG_SYS_FLASH_SIZE           0x01000000
 173
 174 #define CONFIG_SYS_MAX_FLASH_SECT       128     /* max num of sects on one chip */
 175
 176 #define CONFIG_ENV_ADDR         (CONFIG_SYS_TEXT_BASE + 0x40000) /* third sector */
 177
 178 #define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 179 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 180
 181 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of flash banks */
 182
 183 #define CONFIG_FLASH_CFI_DRIVER
 184 #define CONFIG_SYS_FLASH_CFI
 185 #define CONFIG_SYS_FLASH_EMPTY_INFO
 186 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 187 #define CONFIG_SYS_UPDATE_FLASH_SIZE    1
 188 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 189
 190 /*
 191  * Environment settings
 192  */
 193 #define CONFIG_ENV_IS_IN_FLASH  1
 194 #define CONFIG_ENV_SIZE         0x20000
 195 #define CONFIG_ENV_SECT_SIZE    0x20000
 196 #define CONFIG_ENV_OVERWRITE    1
 197
 198 /* Address and size of Redundant Environment Sector     */
 199 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 200 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 201
 202 /*
 203  * Memory map
 204  */
 205 #define CONFIG_SYS_MBAR         0xF0000000
 206 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 207 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 208
 209 /* Use SRAM until RAM will be available */
 210 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 211 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 212
 213
 214 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 215 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 216
 217 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 218 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 219 #   define CONFIG_SYS_RAMBOOT           1
 220 #endif
 221
 222 #define CONFIG_SYS_MONITOR_LEN          (192 << 10)     /* Reserve 192 kB for Monitor   */
 223 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 224 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 225
 226 /*
 227  * Ethernet configuration
 228  */
 229 #define CONFIG_MPC5xxx_FEC      1
 230 #define CONFIG_MPC5xxx_FEC_MII100
 231 /*
 232  * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
 233  */
 234 /* #define CONFIG_MPC5xxx_FEC_MII10 */
 235 #define CONFIG_PHY_ADDR         0x00
 236
 237 /*
 238  * GPIO configuration
 239  */
 240 #define CONFIG_SYS_GPS_PORT_CONFIG      0x10000004
 241
 242 /*
 243  * Miscellaneous configurable options
 244  */
 245 #define CONFIG_SYS_LONGHELP                     /* undef to save memory     */
 246 #define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt   */
 247
 248 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 249 #define CONFIG_SYS_HUSH_PARSER          1       /* Use the HUSH parser          */
 250 #if defined(CONFIG_CMD_KGDB)
 251 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 252 #else
 253 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 254 #endif
 255 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 256 #define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
 257 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 258
 259 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 260 #define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 261 #define CONFIG_SYS_ALT_MEMTEST          1
 262
 263 #define CONFIG_SYS_LOAD_ADDR            0x200000        /* default load address */
 264
 265 #define CONFIG_SYS_HZ                   1000    /* decrementer freq: 1 ms ticks */
 266
 267 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 268 #if defined(CONFIG_CMD_KGDB)
 269 #  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
 270 #endif
 271
 272 /*
 273  * Various low-level settings
 274  */
 275 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 276 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 277
 278 #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
 279 #define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
 280 #define CONFIG_SYS_BOOTCS_CFG           0x00047801
 281 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 282 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 283
 284 #define CONFIG_SYS_CS_BURST             0x00000000
 285 #define CONFIG_SYS_CS_DEADCYCLE 0x33333333
 286
 287 #define CONFIG_SYS_RESET_ADDRESS        0xff000000
 288
 289 #endif /* __CONFIG_H */