include/configs/jupiter.h

   1 /*
   2  * (C) Copyright 2007
   3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 /*
  12  * High Level Configuration Options
  13  * (easy to change)
  14  */
  15
  16 #define CONFIG_MPC5200          1       /* This is an MPC5200 CPU */
  17 #define CONFIG_JUPITER          1       /* ... on Jupiter board */
  18 #define CONFIG_SYS_GENERIC_BOARD
  19 #define CONFIG_DISPLAY_BOARDINFO
  20
  21 /*
  22  * Valid values for CONFIG_SYS_TEXT_BASE are:
  23  * 0xFFF00000   boot high (standard configuration)
  24  * 0x00100000   boot from RAM (for testing only)
  25  */
  26 #ifndef CONFIG_SYS_TEXT_BASE
  27 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  28 #endif
  29
  30 #define CONFIG_SYS_MPC5XXX_CLKIN        33000000 /* ... running at 33.000000MHz */
  31
  32 #define CONFIG_BOARD_EARLY_INIT_R       1
  33 #define CONFIG_BOARD_EARLY_INIT_F       1
  34
  35 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
  36
  37 /*
  38  * Serial console configuration
  39  */
  40 #define CONFIG_PSC_CONSOLE      1       /* console is on PSC1 */
  41 #define CONFIG_BAUDRATE         115200  /* ... at 115200 bps */
  42 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  43
  44 /*
  45  * PCI Mapping:
  46  * 0x40000000 - 0x4fffffff - PCI Memory
  47  * 0x50000000 - 0x50ffffff - PCI IO Space
  48  */
  49 /*#define CONFIG_PCI            */
  50
  51 #if defined(CONFIG_PCI)
  52 #define CONFIG_PCI_PNP          1
  53 #define CONFIG_PCI_SCAN_SHOW    1
  54 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
  55
  56 #define CONFIG_PCI_MEM_BUS      0x40000000
  57 #define CONFIG_PCI_MEM_PHYS     CONFIG_PCI_MEM_BUS
  58 #define CONFIG_PCI_MEM_SIZE     0x10000000
  59
  60 #define CONFIG_PCI_IO_BUS       0x50000000
  61 #define CONFIG_PCI_IO_PHYS      CONFIG_PCI_IO_BUS
  62 #define CONFIG_PCI_IO_SIZE      0x01000000
  63 #endif
  64
  65 #define CONFIG_SYS_XLB_PIPELINING       1
  66
  67 #define CONFIG_MII              1
  68 #define CONFIG_SYS_RX_ETH_BUFFER        8  /* use 8 rx buffer on eepro100  */
  69
  70 /* Partitions */
  71 #define CONFIG_MAC_PARTITION
  72 #define CONFIG_DOS_PARTITION
  73 #define CONFIG_ISO_PARTITION
  74
  75 #define CONFIG_TIMESTAMP                /* Print image info with timestamp */
  76
  77
  78 /*
  79  * BOOTP options
  80  */
  81 #define CONFIG_BOOTP_BOOTFILESIZE
  82 #define CONFIG_BOOTP_BOOTPATH
  83 #define CONFIG_BOOTP_GATEWAY
  84 #define CONFIG_BOOTP_HOSTNAME
  85
  86
  87 /*
  88  * Command line configuration.
  89  */
  90 #define CONFIG_CMD_SNTP
  91
  92 #if defined(CONFIG_PCI)
  93 #define CODFIG_CMD_PCI
  94 #endif
  95
  96
  97 /*
  98  * Autobooting
  99  */
 100 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds */
 101
 102 #define CONFIG_PREBOOT  "echo;" \
 103         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 104         "echo"
 105
 106 #undef  CONFIG_BOOTARGS
 107
 108 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 109         "netdev=eth0\0"                                                 \
 110         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 111                 "nfsroot=${serverip}:${rootpath}\0"                     \
 112         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 113         "addip=setenv bootargs ${bootargs} "                            \
 114                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 115                 ":${hostname}:${netdev}:off panic=1\0"                  \
 116         "flash_nfs=run nfsargs addip addcons;"                          \
 117                 "bootm ${kernel_addr}\0"                                \
 118         "flash_self=run ramargs addip;"                                 \
 119                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 120         "addcons=setenv bootargs ${bootargs} console=${contyp},"        \
 121                 "${baudrate}\0"                                         \
 122         "contyp=ttyS0\0"                                                \
 123         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;"    \
 124                 "bootm\0"                                               \
 125         "rootpath=/opt/eldk/ppc_6xx\0"                                  \
 126         "bootfile=/tftpboot/jupiter/uImage\0"                           \
 127         ""
 128
 129 #define CONFIG_BOOTCOMMAND      "run flash_self"
 130
 131 /*
 132  * IPB Bus clocking configuration.
 133  */
 134 #undef CONFIG_SYS_IPBSPEED_133                  /* define for 133MHz speed */
 135
 136 #if 0
 137 /* pass open firmware flat tree */
 138 #define CONFIG_OF_LIBFDT        1
 139 #define CONFIG_OF_BOARD_SETUP   1
 140
 141 #define OF_CPU                  "PowerPC,5200@0"
 142 #define OF_SOC                  "soc5200@f0000000"
 143 #define OF_TBCLK                (bd->bi_busfreq / 8)
 144 #define OF_STDOUT_PATH          "/soc5200@f0000000/serial@2000"
 145 #endif
 146
 147 #if 0
 148 /*
 149  * I2C configuration
 150  */
 151 #define CONFIG_HARD_I2C         1       /* I2C with hardware support */
 152 #define CONFIG_SYS_I2C_MODULE           2       /* Select I2C module #1 or #2 */
 153
 154 #define CONFIG_SYS_I2C_SPEED            100000 /* 100 kHz */
 155 #define CONFIG_SYS_I2C_SLAVE            0x7F
 156
 157 /*
 158  * EEPROM configuration
 159  */
 160 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50    /* 1010000x */
 161 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 162 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 163 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   70
 164 #endif
 165
 166 /*
 167  * Flash configuration
 168  */
 169 #define CONFIG_SYS_FLASH_BASE           0xFF000000
 170 #define CONFIG_SYS_FLASH_SIZE           0x01000000
 171
 172 #define CONFIG_SYS_MAX_FLASH_SECT       128     /* max num of sects on one chip */
 173
 174 #define CONFIG_ENV_ADDR         (CONFIG_SYS_TEXT_BASE + 0x40000) /* third sector */
 175
 176 #define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 177 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 178
 179 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of flash banks */
 180
 181 #define CONFIG_FLASH_CFI_DRIVER
 182 #define CONFIG_SYS_FLASH_CFI
 183 #define CONFIG_SYS_FLASH_EMPTY_INFO
 184 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 185 #define CONFIG_SYS_UPDATE_FLASH_SIZE    1
 186 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 187
 188 /*
 189  * Environment settings
 190  */
 191 #define CONFIG_ENV_IS_IN_FLASH  1
 192 #define CONFIG_ENV_SIZE         0x20000
 193 #define CONFIG_ENV_SECT_SIZE    0x20000
 194 #define CONFIG_ENV_OVERWRITE    1
 195
 196 /* Address and size of Redundant Environment Sector     */
 197 #define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 198 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 199
 200 /*
 201  * Memory map
 202  */
 203 #define CONFIG_SYS_MBAR         0xF0000000
 204 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 205 #define CONFIG_SYS_DEFAULT_MBAR 0x80000000
 206
 207 /* Use SRAM until RAM will be available */
 208 #define CONFIG_SYS_INIT_RAM_ADDR        MPC5XXX_SRAM
 209 #define CONFIG_SYS_INIT_RAM_SIZE        MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 210
 211
 212 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 213 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 214
 215 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 216 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 217 #   define CONFIG_SYS_RAMBOOT           1
 218 #endif
 219
 220 #define CONFIG_SYS_MONITOR_LEN          (192 << 10)     /* Reserve 192 kB for Monitor   */
 221 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 222 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 223
 224 /*
 225  * Ethernet configuration
 226  */
 227 #define CONFIG_MPC5xxx_FEC      1
 228 #define CONFIG_MPC5xxx_FEC_MII100
 229 /*
 230  * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
 231  */
 232 /* #define CONFIG_MPC5xxx_FEC_MII10 */
 233 #define CONFIG_PHY_ADDR         0x00
 234
 235 /*
 236  * GPIO configuration
 237  */
 238 #define CONFIG_SYS_GPS_PORT_CONFIG      0x10000004
 239
 240 /*
 241  * Miscellaneous configurable options
 242  */
 243 #define CONFIG_SYS_LONGHELP                     /* undef to save memory     */
 244
 245 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 246 #define CONFIG_SYS_HUSH_PARSER          1       /* Use the HUSH parser          */
 247 #if defined(CONFIG_CMD_KGDB)
 248 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 249 #else
 250 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 251 #endif
 252 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 253 #define CONFIG_SYS_MAXARGS              16              /* max number of command args   */
 254 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 255
 256 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 257 #define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 258 #define CONFIG_SYS_ALT_MEMTEST          1
 259
 260 #define CONFIG_SYS_LOAD_ADDR            0x200000        /* default load address */
 261
 262 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC5xxx CPUs */
 263 #if defined(CONFIG_CMD_KGDB)
 264 #  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
 265 #endif
 266
 267 /*
 268  * Various low-level settings
 269  */
 270 #define CONFIG_SYS_HID0_INIT            HID0_ICE | HID0_ICFI
 271 #define CONFIG_SYS_HID0_FINAL           HID0_ICE
 272
 273 #define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
 274 #define CONFIG_SYS_BOOTCS_SIZE          CONFIG_SYS_FLASH_SIZE
 275 #define CONFIG_SYS_BOOTCS_CFG           0x00047801
 276 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 277 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 278
 279 #define CONFIG_SYS_CS_BURST             0x00000000
 280 #define CONFIG_SYS_CS_DEADCYCLE 0x33333333
 281
 282 #define CONFIG_SYS_RESET_ADDRESS        0xff000000
 283
 284 #endif /* __CONFIG_H */