include/configs/km/km83xx-common.h

   1 /*
   2  * (C) Copyright 2010
   3  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __CONFIG_KM83XX_H
   9 #define __CONFIG_KM83XX_H
  10
  11 #define CONFIG_SYS_GENERIC_BOARD
  12 #define CONFIG_DISPLAY_BOARDINFO
  13
  14 /* include common defines/options for all Keymile boards */
  15 #include "keymile-common.h"
  16 #include "km-powerpc.h"
  17
  18 #ifndef MTDIDS_DEFAULT
  19 # define MTDIDS_DEFAULT "nor0=boot"
  20 #endif /* MTDIDS_DEFAULT */
  21
  22 #ifndef MTDPARTS_DEFAULT
  23 # define MTDPARTS_DEFAULT       "mtdparts="                     \
  24         "boot:"                                                 \
  25                 "768k(u-boot),"                                 \
  26                 "128k(env),"                                    \
  27                 "128k(envred),"                                 \
  28                 "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");"
  29 #endif /* MTDPARTS_DEFAULT */
  30
  31 #define CONFIG_MISC_INIT_R
  32 /*
  33  * System Clock Setup
  34  */
  35 #define CONFIG_83XX_CLKIN               66000000
  36 #define CONFIG_SYS_CLK_FREQ             66000000
  37 #define CONFIG_83XX_PCICLK              66000000
  38
  39 /*
  40  * IMMR new address
  41  */
  42 #define CONFIG_SYS_IMMR         0xE0000000
  43
  44 /*
  45  * Bus Arbitration Configuration Register (ACR)
  46  */
  47 #define CONFIG_SYS_ACR_PIPE_DEP 3       /* pipeline depth 4 transactions */
  48 #define CONFIG_SYS_ACR_RPTCNT   3       /* 4 consecutive transactions */
  49 #define CONFIG_SYS_ACR_APARK    0       /* park bus to master (below) */
  50 #define CONFIG_SYS_ACR_PARKM    3       /* parking master = QuiccEngine */
  51
  52 /*
  53  * DDR Setup
  54  */
  55 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
  56 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  57 #define CONFIG_SYS_SDRAM_BASE2  (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */
  58
  59 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  60 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN | \
  61                                         DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
  62
  63 #define CFG_83XX_DDR_USES_CS0
  64
  65 /*
  66  * Manually set up DDR parameters
  67  */
  68 #define CONFIG_DDR_II
  69 #define CONFIG_SYS_DDR_SIZE             2048 /* MB */
  70
  71 /*
  72  * The reserved memory
  73  */
  74 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
  75 #define CONFIG_SYS_FLASH_BASE           0xF0000000
  76
  77 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
  78 #define CONFIG_SYS_RAMBOOT
  79 #endif
  80
  81 /* Reserve 768 kB for Mon */
  82 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
  83
  84 /*
  85  * Initial RAM Base Address Setup
  86  */
  87 #define CONFIG_SYS_INIT_RAM_LOCK
  88 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
  89 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* End of used area in RAM */
  90 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
  91                                                 GENERATED_GBL_DATA_SIZE)
  92
  93 /*
  94  * Init Local Bus Memory Controller:
  95  *
  96  * Bank Bus     Machine PortSz  Size  Device
  97  * ---- ---     ------- ------  -----  ------
  98  *  0   Local   GPCM    16 bit  256MB FLASH
  99  *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
 100  *
 101  */
 102 /*
 103  * FLASH on the Local Bus
 104  */
 105 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 106 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 107 #define CONFIG_SYS_FLASH_SIZE           256 /* max FLASH size is 256M */
 108 #define CONFIG_SYS_FLASH_PROTECTION
 109 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 110
 111 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
 112 #define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_256MB)
 113
 114 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE | \
 115                                 BR_PS_16 | /* 16 bit port size */ \
 116                                 BR_MS_GPCM | /* MSEL = GPCM */ \
 117                                 BR_V)
 118
 119 #define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
 120                                 OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 121                                 OR_GPCM_SCY_5 | \
 122                                 OR_GPCM_TRLX_SET | OR_GPCM_EAD)
 123
 124 #define CONFIG_SYS_MAX_FLASH_BANKS      1   /* max num of flash banks   */
 125 #define CONFIG_SYS_MAX_FLASH_SECT       512 /* max num of sects on one chip */
 126 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
 127
 128 /*
 129  * PRIO1/PIGGY on the local bus CS1
 130  */
 131 /* Window base at flash base */
 132 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_KMBEC_FPGA_BASE
 133 #define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_128MB)
 134
 135 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_KMBEC_FPGA_BASE | \
 136                                 BR_PS_8 | /* 8 bit port size */ \
 137                                 BR_MS_GPCM | /* MSEL = GPCM */ \
 138                                 BR_V)
 139 #define CONFIG_SYS_OR1_PRELIM   (MEG_TO_AM(CONFIG_SYS_KMBEC_FPGA_SIZE) | \
 140                                 OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 141                                 OR_GPCM_SCY_2 | \
 142                                 OR_GPCM_TRLX_SET | OR_GPCM_EAD)
 143
 144 /*
 145  * Serial Port
 146  */
 147 #define CONFIG_CONS_INDEX       1
 148 #define CONFIG_SYS_NS16550
 149 #define CONFIG_SYS_NS16550_SERIAL
 150 #define CONFIG_SYS_NS16550_REG_SIZE     1
 151 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 152
 153 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 154 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 155
 156 /* Pass open firmware flat tree */
 157 #define CONFIG_OF_LIBFDT
 158 #define CONFIG_OF_BOARD_SETUP
 159 #define CONFIG_OF_STDOUT_VIA_ALIAS
 160
 161 /*
 162  * QE UEC ethernet configuration
 163  */
 164 #define CONFIG_UEC_ETH
 165 #define CONFIG_ETHPRIME         "UEC0"
 166
 167 #if !defined(CONFIG_MPC8309)
 168 #define CONFIG_UEC_ETH1         /* GETH1 */
 169 #define UEC_VERBOSE_DEBUG       1
 170 #endif
 171
 172 #ifdef CONFIG_UEC_ETH1
 173 #define CONFIG_SYS_UEC1_UCC_NUM 3       /* UCC4 */
 174 #define CONFIG_SYS_UEC1_RX_CLK          QE_CLK_NONE /* not used in RMII Mode */
 175 #define CONFIG_SYS_UEC1_TX_CLK          QE_CLK17
 176 #define CONFIG_SYS_UEC1_ETH_TYPE        FAST_ETH
 177 #define CONFIG_SYS_UEC1_PHY_ADDR        0
 178 #define CONFIG_SYS_UEC1_INTERFACE_TYPE  PHY_INTERFACE_MODE_RMII
 179 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 180 #endif
 181
 182 /*
 183  * Environment
 184  */
 185
 186 #ifndef CONFIG_SYS_RAMBOOT
 187 #define CONFIG_ENV_IS_IN_FLASH
 188 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 189                                         CONFIG_SYS_MONITOR_LEN)
 190 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 191 #define CONFIG_ENV_OFFSET       (CONFIG_SYS_MONITOR_LEN)
 192
 193 /* Address and size of Redundant Environment Sector     */
 194 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + \
 195                                                 CONFIG_ENV_SECT_SIZE)
 196 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 197
 198 #else /* CFG_SYS_RAMBOOT */
 199 #define CONFIG_SYS_NO_FLASH             /* Flash is not usable now */
 200 #define CONFIG_ENV_IS_NOWHERE           /* Store ENV in memory only */
 201 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 202 #define CONFIG_ENV_SIZE         0x2000
 203 #endif /* CFG_SYS_RAMBOOT */
 204
 205 /* I2C */
 206 #define CONFIG_SYS_I2C
 207 #define CONFIG_SYS_NUM_I2C_BUSES        4
 208 #define CONFIG_SYS_I2C_MAX_HOPS         1
 209 #define CONFIG_SYS_I2C_FSL
 210 #define CONFIG_SYS_FSL_I2C_SPEED        200000
 211 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 212 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 213 #define CONFIG_SYS_I2C_OFFSET           0x3000
 214 #define CONFIG_SYS_FSL_I2C2_SPEED       200000
 215 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 216 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 217 #define CONFIG_SYS_I2C_BUSES    {{0, {I2C_NULL_HOP} }, \
 218                 {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
 219                 {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
 220                 {1, {I2C_NULL_HOP} } }
 221
 222 #define CONFIG_KM_IVM_BUS               2       /* I2C2 (Mux-Port 1)*/
 223
 224 /* I2C SYSMON (LM75, AD7414 is almost compatible) */
 225 #define CONFIG_DTT_LM75         /* ON Semi's LM75 */
 226 #define CONFIG_DTT_SENSORS      {0, 1, 2, 3}    /* Sensor addresses */
 227 #define CONFIG_SYS_DTT_MAX_TEMP 70
 228 #define CONFIG_SYS_DTT_HYSTERESIS       3
 229 #define CONFIG_SYS_DTT_BUS_NUM          1
 230
 231 #if defined(CONFIG_CMD_NAND)
 232 #define CONFIG_NAND_KMETER1
 233 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 234 #define CONFIG_SYS_NAND_BASE            CONFIG_SYS_KMBEC_FPGA_BASE
 235 #endif
 236
 237 #if defined(CONFIG_PCI)
 238 #define CONFIG_CMD_PCI
 239 #endif
 240
 241 /*
 242  * For booting Linux, the board info and command line data
 243  * have to be in the first 8 MB of memory, since this is
 244  * the maximum mapped by the Linux kernel during initialization.
 245  */
 246 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)
 247
 248 /*
 249  * Core HID Setup
 250  */
 251 #define CONFIG_SYS_HID0_INIT            0x000000000
 252 #define CONFIG_SYS_HID0_FINAL           (HID0_ENABLE_MACHINE_CHECK | \
 253                                          HID0_ENABLE_INSTRUCTION_CACHE)
 254 #define CONFIG_SYS_HID2                 HID2_HBE
 255
 256 /*
 257  * MMU Setup
 258  */
 259
 260 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 261
 262 /* DDR: cache cacheable */
 263 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \
 264                                 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 265 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
 266                                         BATU_VS | BATU_VP)
 267 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 268 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 269
 270 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
 271 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_RW | \
 272                                 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 273 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS \
 274                                         | BATU_VP)
 275 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 276 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 277
 278 /* PRIO1, PIGGY:  icache cacheable, but dcache-inhibit and guarded */
 279 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
 280                                 BATL_MEMCOHERENCE)
 281 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_KMBEC_FPGA_BASE | BATU_BL_128M | \
 282                                 BATU_VS | BATU_VP)
 283 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \
 284                                  BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 285 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 286
 287 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 288 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 289                                         BATL_MEMCOHERENCE)
 290 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \
 291                                         BATU_VS | BATU_VP)
 292 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
 293                                  BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 294 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 295
 296 /* Stack in dcache: cacheable, no memory coherence */
 297 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
 298 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
 299                                         BATU_VS | BATU_VP)
 300 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 301 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 302
 303 /*
 304  * Internal Definitions
 305  */
 306 #define BOOTFLASH_START 0xF0000000
 307
 308 #define CONFIG_KM_CONSOLE_TTY   "ttyS0"
 309
 310 /*
 311  * Environment Configuration
 312  */
 313 #define CONFIG_ENV_OVERWRITE
 314 #ifndef CONFIG_KM_DEF_ENV               /* if not set by keymile-common.h */
 315 #define CONFIG_KM_DEF_ENV "km-common=empty\0"
 316 #endif
 317
 318 #ifndef CONFIG_KM_DEF_ARCH
 319 #define CONFIG_KM_DEF_ARCH      "arch=ppc_82xx\0"
 320 #endif
 321
 322 #define CONFIG_EXTRA_ENV_SETTINGS \
 323         CONFIG_KM_DEF_ENV                                               \
 324         CONFIG_KM_DEF_ARCH                                              \
 325         "newenv="                                                       \
 326                 "prot off 0xF00C0000 +0x40000 && "                      \
 327                 "era 0xF00C0000 +0x40000\0"                             \
 328         "unlock=yes\0"                                                  \
 329         ""
 330
 331 #if defined(CONFIG_UEC_ETH)
 332 #define CONFIG_HAS_ETH0
 333 #endif
 334
 335 #endif /* __CONFIG_KM83XX_H */