include/configs/ls1021atwr.h

   1 /*
   2  * Copyright 2014 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 #define CONFIG_ARMV7_PSCI_1_0
  11
  12 #define CONFIG_ARMV7_SECURE_BASE        OCRAM_BASE_S_ADDR
  13
  14 #define CONFIG_SYS_FSL_CLK
  15
  16 #define CONFIG_SKIP_LOWLEVEL_INIT
  17 #define CONFIG_DEEP_SLEEP
  18
  19 /*
  20  * Size of malloc() pool
  21  */
  22 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 16 * 1024 * 1024)
  23
  24 #define CONFIG_SYS_INIT_RAM_ADDR        OCRAM_BASE_ADDR
  25 #define CONFIG_SYS_INIT_RAM_SIZE        OCRAM_SIZE
  26
  27 /*
  28  * USB
  29  */
  30
  31 /*
  32  * EHCI Support - disbaled by default as
  33  * there is no signal coming out of soc on
  34  * this board for this controller. However,
  35  * the silicon still has this controller,
  36  * and anyone can use this controller by
  37  * taking signals out on their board.
  38  */
  39
  40 /*#define CONFIG_HAS_FSL_DR_USB*/
  41
  42 #ifdef CONFIG_HAS_FSL_DR_USB
  43 #define CONFIG_USB_EHCI_FSL
  44 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  45 #endif
  46
  47 /* XHCI Support - enabled by default */
  48 #define CONFIG_HAS_FSL_XHCI_USB
  49
  50 #ifdef CONFIG_HAS_FSL_XHCI_USB
  51 #define CONFIG_USB_XHCI_FSL
  52 #define CONFIG_USB_MAX_CONTROLLER_COUNT        1
  53 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS     2
  54 #endif
  55
  56 #define CONFIG_SYS_CLK_FREQ             100000000
  57 #define CONFIG_DDR_CLK_FREQ             100000000
  58
  59 #define DDR_SDRAM_CFG                   0x470c0008
  60 #define DDR_CS0_BNDS                    0x008000bf
  61 #define DDR_CS0_CONFIG                  0x80014302
  62 #define DDR_TIMING_CFG_0                0x50550004
  63 #define DDR_TIMING_CFG_1                0xbcb38c56
  64 #define DDR_TIMING_CFG_2                0x0040d120
  65 #define DDR_TIMING_CFG_3                0x010e1000
  66 #define DDR_TIMING_CFG_4                0x00000001
  67 #define DDR_TIMING_CFG_5                0x03401400
  68 #define DDR_SDRAM_CFG_2                 0x00401010
  69 #define DDR_SDRAM_MODE                  0x00061c60
  70 #define DDR_SDRAM_MODE_2                0x00180000
  71 #define DDR_SDRAM_INTERVAL              0x18600618
  72 #define DDR_DDR_WRLVL_CNTL              0x8655f605
  73 #define DDR_DDR_WRLVL_CNTL_2            0x05060607
  74 #define DDR_DDR_WRLVL_CNTL_3            0x05050505
  75 #define DDR_DDR_CDR1                    0x80040000
  76 #define DDR_DDR_CDR2                    0x00000001
  77 #define DDR_SDRAM_CLK_CNTL              0x02000000
  78 #define DDR_DDR_ZQ_CNTL                 0x89080600
  79 #define DDR_CS0_CONFIG_2                0
  80 #define DDR_SDRAM_CFG_MEM_EN            0x80000000
  81 #define SDRAM_CFG2_D_INIT               0x00000010
  82 #define DDR_CDR2_VREF_TRAIN_EN          0x00000080
  83 #define SDRAM_CFG2_FRC_SR               0x80000000
  84 #define SDRAM_CFG_BI                    0x00000001
  85
  86 #ifdef CONFIG_RAMBOOT_PBL
  87 #define CONFIG_SYS_FSL_PBL_PBI  board/freescale/ls1021atwr/ls102xa_pbi.cfg
  88 #endif
  89
  90 #ifdef CONFIG_SD_BOOT
  91 #ifdef CONFIG_SD_BOOT_QSPI
  92 #define CONFIG_SYS_FSL_PBL_RCW  \
  93         board/freescale/ls1021atwr/ls102xa_rcw_sd_qspi.cfg
  94 #else
  95 #define CONFIG_SYS_FSL_PBL_RCW  \
  96         board/freescale/ls1021atwr/ls102xa_rcw_sd_ifc.cfg
  97 #endif
  98 #define CONFIG_SPL_FRAMEWORK
  99 #define CONFIG_SPL_LDSCRIPT     "arch/$(ARCH)/cpu/u-boot-spl.lds"
 100
 101 #ifdef CONFIG_SECURE_BOOT
 102 /*
 103  * HDR would be appended at end of image and copied to DDR along
 104  * with U-Boot image.
 105  */
 106 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
 107 #endif /* ifdef CONFIG_SECURE_BOOT */
 108
 109 #define CONFIG_SPL_TEXT_BASE            0x10000000
 110 #define CONFIG_SPL_MAX_SIZE             0x1a000
 111 #define CONFIG_SPL_STACK                0x1001d000
 112 #define CONFIG_SPL_PAD_TO               0x1c000
 113 #define CONFIG_SYS_TEXT_BASE            0x82000000
 114
 115 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE + \
 116                 CONFIG_SYS_MONITOR_LEN)
 117 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 118 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
 119 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 120
 121 #ifdef CONFIG_U_BOOT_HDR_SIZE
 122 /*
 123  * HDR would be appended at end of image and copied to DDR along
 124  * with U-Boot image. Here u-boot max. size is 512K. So if binary
 125  * size increases then increase this size in case of secure boot as
 126  * it uses raw u-boot image instead of fit image.
 127  */
 128 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 129 #else
 130 #define CONFIG_SYS_MONITOR_LEN          0x100000
 131 #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */
 132 #endif
 133
 134 #ifdef CONFIG_QSPI_BOOT
 135 #define CONFIG_SYS_TEXT_BASE            0x40100000
 136 #endif
 137
 138 #ifndef CONFIG_SYS_TEXT_BASE
 139 #define CONFIG_SYS_TEXT_BASE            0x60100000
 140 #endif
 141
 142 #define CONFIG_NR_DRAM_BANKS            1
 143 #define PHYS_SDRAM                      0x80000000
 144 #define PHYS_SDRAM_SIZE                 (1u * 1024 * 1024 * 1024)
 145
 146 #define CONFIG_SYS_DDR_SDRAM_BASE      0x80000000UL
 147 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 148
 149 #if !defined(CONFIG_SD_BOOT) && !defined(CONFIG_NAND_BOOT) && \
 150         !defined(CONFIG_QSPI_BOOT)
 151 #define CONFIG_U_QE
 152 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 153 #endif
 154
 155 /*
 156  * IFC Definitions
 157  */
 158 #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
 159 #define CONFIG_FSL_IFC
 160 #define CONFIG_SYS_FLASH_BASE           0x60000000
 161 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 162
 163 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
 164 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 165                                 CSPR_PORT_SIZE_16 | \
 166                                 CSPR_MSEL_NOR | \
 167                                 CSPR_V)
 168 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128 * 1024 * 1024)
 169
 170 /* NOR Flash Timing Params */
 171 #define CONFIG_SYS_NOR_CSOR             (CSOR_NOR_ADM_SHIFT(4) | \
 172                                         CSOR_NOR_TRHZ_80)
 173 #define CONFIG_SYS_NOR_FTIM0            (FTIM0_NOR_TACSE(0x4) | \
 174                                         FTIM0_NOR_TEADC(0x5) | \
 175                                         FTIM0_NOR_TAVDS(0x0) | \
 176                                         FTIM0_NOR_TEAHC(0x5))
 177 #define CONFIG_SYS_NOR_FTIM1            (FTIM1_NOR_TACO(0x35) | \
 178                                         FTIM1_NOR_TRAD_NOR(0x1A) | \
 179                                         FTIM1_NOR_TSEQRAD_NOR(0x13))
 180 #define CONFIG_SYS_NOR_FTIM2            (FTIM2_NOR_TCS(0x4) | \
 181                                         FTIM2_NOR_TCH(0x4) | \
 182                                         FTIM2_NOR_TWP(0x1c) | \
 183                                         FTIM2_NOR_TWPH(0x0e))
 184 #define CONFIG_SYS_NOR_FTIM3            0
 185
 186 #define CONFIG_FLASH_CFI_DRIVER
 187 #define CONFIG_SYS_FLASH_CFI
 188 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 189 #define CONFIG_SYS_FLASH_QUIET_TEST
 190 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 191
 192 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 193 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 194 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 195 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 196
 197 #define CONFIG_SYS_FLASH_EMPTY_INFO
 198 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE_PHYS }
 199
 200 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
 201 #define CONFIG_SYS_WRITE_SWAPPED_DATA
 202 #endif
 203
 204 /* CPLD */
 205
 206 #define CONFIG_SYS_CPLD_BASE    0x7fb00000
 207 #define CPLD_BASE_PHYS          CONFIG_SYS_CPLD_BASE
 208
 209 #define CONFIG_SYS_FPGA_CSPR_EXT        (0x0)
 210 #define CONFIG_SYS_FPGA_CSPR            (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
 211                                         CSPR_PORT_SIZE_8 | \
 212                                         CSPR_MSEL_GPCM | \
 213                                         CSPR_V)
 214 #define CONFIG_SYS_FPGA_AMASK           IFC_AMASK(64 * 1024)
 215 #define CONFIG_SYS_FPGA_CSOR            (CSOR_NOR_ADM_SHIFT(4) | \
 216                                         CSOR_NOR_NOR_MODE_AVD_NOR | \
 217                                         CSOR_NOR_TRHZ_80)
 218
 219 /* CPLD Timing parameters for IFC GPCM */
 220 #define CONFIG_SYS_FPGA_FTIM0           (FTIM0_GPCM_TACSE(0xf) | \
 221                                         FTIM0_GPCM_TEADC(0xf) | \
 222                                         FTIM0_GPCM_TEAHC(0xf))
 223 #define CONFIG_SYS_FPGA_FTIM1           (FTIM1_GPCM_TACO(0xff) | \
 224                                         FTIM1_GPCM_TRAD(0x3f))
 225 #define CONFIG_SYS_FPGA_FTIM2           (FTIM2_GPCM_TCS(0xf) | \
 226                                         FTIM2_GPCM_TCH(0xf) | \
 227                                         FTIM2_GPCM_TWP(0xff))
 228 #define CONFIG_SYS_FPGA_FTIM3           0x0
 229 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 230 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 231 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 232 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 233 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 234 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 235 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 236 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 237 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_FPGA_CSPR_EXT
 238 #define CONFIG_SYS_CSPR1                CONFIG_SYS_FPGA_CSPR
 239 #define CONFIG_SYS_AMASK1               CONFIG_SYS_FPGA_AMASK
 240 #define CONFIG_SYS_CSOR1                CONFIG_SYS_FPGA_CSOR
 241 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_FPGA_FTIM0
 242 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_FPGA_FTIM1
 243 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_FPGA_FTIM2
 244 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_FPGA_FTIM3
 245
 246 /*
 247  * Serial Port
 248  */
 249 #ifdef CONFIG_LPUART
 250 #define CONFIG_LPUART_32B_REG
 251 #else
 252 #define CONFIG_CONS_INDEX               1
 253 #define CONFIG_SYS_NS16550_SERIAL
 254 #ifndef CONFIG_DM_SERIAL
 255 #define CONFIG_SYS_NS16550_REG_SIZE     1
 256 #endif
 257 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
 258 #endif
 259
 260 /*
 261  * I2C
 262  */
 263 #define CONFIG_SYS_I2C
 264 #define CONFIG_SYS_I2C_MXC
 265 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
 266 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
 267 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
 268
 269 /* EEPROM */
 270 #define CONFIG_ID_EEPROM
 271 #define CONFIG_SYS_I2C_EEPROM_NXID
 272 #define CONFIG_SYS_EEPROM_BUS_NUM               1
 273 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x53
 274 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          1
 275 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       3
 276 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   5
 277
 278 /*
 279  * MMC
 280  */
 281 #define CONFIG_FSL_ESDHC
 282
 283 /* SPI */
 284 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 285 /* QSPI */
 286 #define QSPI0_AMBA_BASE                 0x40000000
 287 #define FSL_QSPI_FLASH_SIZE             (1 << 24)
 288 #define FSL_QSPI_FLASH_NUM              2
 289
 290 /* DSPI */
 291 #endif
 292
 293 /* DM SPI */
 294 #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI)
 295 #define CONFIG_DM_SPI_FLASH
 296 #endif
 297
 298 /*
 299  * Video
 300  */
 301 #ifdef CONFIG_VIDEO_FSL_DCU_FB
 302 #define CONFIG_VIDEO_LOGO
 303 #define CONFIG_VIDEO_BMP_LOGO
 304
 305 #define CONFIG_FSL_DCU_SII9022A
 306 #define CONFIG_SYS_I2C_DVI_BUS_NUM      1
 307 #define CONFIG_SYS_I2C_DVI_ADDR         0x39
 308 #endif
 309
 310 /*
 311  * eTSEC
 312  */
 313 #define CONFIG_TSEC_ENET
 314
 315 #ifdef CONFIG_TSEC_ENET
 316 #define CONFIG_MII
 317 #define CONFIG_MII_DEFAULT_TSEC         1
 318 #define CONFIG_TSEC1                    1
 319 #define CONFIG_TSEC1_NAME               "eTSEC1"
 320 #define CONFIG_TSEC2                    1
 321 #define CONFIG_TSEC2_NAME               "eTSEC2"
 322 #define CONFIG_TSEC3                    1
 323 #define CONFIG_TSEC3_NAME               "eTSEC3"
 324
 325 #define TSEC1_PHY_ADDR                  2
 326 #define TSEC2_PHY_ADDR                  0
 327 #define TSEC3_PHY_ADDR                  1
 328
 329 #define TSEC1_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 330 #define TSEC2_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 331 #define TSEC3_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 332
 333 #define TSEC1_PHYIDX                    0
 334 #define TSEC2_PHYIDX                    0
 335 #define TSEC3_PHYIDX                    0
 336
 337 #define CONFIG_ETHPRIME                 "eTSEC1"
 338
 339 #define CONFIG_PHY_GIGE
 340 #define CONFIG_PHYLIB
 341 #define CONFIG_PHY_ATHEROS
 342
 343 #define CONFIG_HAS_ETH0
 344 #define CONFIG_HAS_ETH1
 345 #define CONFIG_HAS_ETH2
 346 #endif
 347
 348 /* PCIe */
 349 #define CONFIG_PCIE1            /* PCIE controller 1 */
 350 #define CONFIG_PCIE2            /* PCIE controller 2 */
 351
 352 #ifdef CONFIG_PCI
 353 #define CONFIG_PCI_SCAN_SHOW
 354 #define CONFIG_CMD_PCI
 355 #endif
 356
 357 #define CONFIG_CMDLINE_TAG
 358
 359 #define CONFIG_PEN_ADDR_BIG_ENDIAN
 360 #define CONFIG_LAYERSCAPE_NS_ACCESS
 361 #define CONFIG_SMP_PEN_ADDR             0x01ee0200
 362 #define COUNTER_FREQUENCY               12500000
 363
 364 #define CONFIG_HWCONFIG
 365 #define HWCONFIG_BUFFER_SIZE            256
 366
 367 #define CONFIG_FSL_DEVICE_DISABLE
 368
 369 #include <config_distro_defaults.h>
 370 #define BOOT_TARGET_DEVICES(func) \
 371         func(MMC, mmc, 0) \
 372         func(USB, usb, 0)
 373 #include <config_distro_bootcmd.h>
 374
 375 #ifdef CONFIG_LPUART
 376 #define CONFIG_EXTRA_ENV_SETTINGS       \
 377         "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \
 378         "initrd_high=0xffffffff\0"      \
 379         "fdt_high=0xffffffff\0"         \
 380         "fdt_addr=0x64f00000\0"         \
 381         "kernel_addr=0x65000000\0"      \
 382         "scriptaddr=0x80000000\0"       \
 383         "fdtheader_addr_r=0x80100000\0" \
 384         "kernelheader_addr_r=0x80200000\0"      \
 385         "kernel_addr_r=0x81000000\0"    \
 386         "fdt_addr_r=0x90000000\0"       \
 387         "ramdisk_addr_r=0xa0000000\0"   \
 388         "load_addr=0xa0000000\0"        \
 389         "kernel_size=0x2800000\0"       \
 390         BOOTENV                         \
 391         "boot_scripts=ls1021atwr_boot.scr\0"    \
 392                 "scan_dev_for_boot_part="       \
 393                         "part list ${devtype} ${devnum} devplist; "     \
 394                         "env exists devplist || setenv devplist 1; "    \
 395                         "for distro_bootpart in ${devplist}; do "       \
 396                         "if fstype ${devtype} "                         \
 397                                 "${devnum}:${distro_bootpart} "         \
 398                                 "bootfstype; then "                     \
 399                                 "run scan_dev_for_boot; "               \
 400                         "fi; "                  \
 401                 "done\0"                        \
 402         "installer=load mmc 0:2 $load_addr "    \
 403                 "/flex_installer_arm32.itb; "           \
 404                 "bootm $load_addr#ls1021atwr\0" \
 405         "qspi_bootcmd=echo Trying load from qspi..;"    \
 406                 "sf probe && sf read $load_addr "       \
 407                 "$kernel_addr $kernel_size && bootm $load_addr#$board\0"        \
 408         "nor_bootcmd=echo Trying load from nor..;"      \
 409                 "cp.b $kernel_addr $load_addr "         \
 410                 "$kernel_size && bootm $load_addr#$board\0"
 411 #else
 412 #define CONFIG_EXTRA_ENV_SETTINGS       \
 413         "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \
 414         "initrd_high=0xffffffff\0"      \
 415         "fdt_high=0xffffffff\0"         \
 416         "fdt_addr=0x64f00000\0"         \
 417         "kernel_addr=0x65000000\0"      \
 418         "scriptaddr=0x80000000\0"       \
 419         "fdtheader_addr_r=0x80100000\0" \
 420         "kernelheader_addr_r=0x80200000\0"      \
 421         "kernel_addr_r=0x81000000\0"    \
 422         "fdt_addr_r=0x90000000\0"       \
 423         "ramdisk_addr_r=0xa0000000\0"   \
 424         "load_addr=0xa0000000\0"        \
 425         "kernel_size=0x2800000\0"       \
 426         BOOTENV                         \
 427         "boot_scripts=ls1021atwr_boot.scr\0"    \
 428                 "scan_dev_for_boot_part="       \
 429                         "part list ${devtype} ${devnum} devplist; "     \
 430                         "env exists devplist || setenv devplist 1; "    \
 431                         "for distro_bootpart in ${devplist}; do "       \
 432                         "if fstype ${devtype} "                         \
 433                                 "${devnum}:${distro_bootpart} "         \
 434                                 "bootfstype; then "                     \
 435                                 "run scan_dev_for_boot; "               \
 436                         "fi; "                  \
 437                 "done\0"                        \
 438         "installer=load mmc 0:2 $load_addr "    \
 439                 "/flex_installer_arm32.itb; "           \
 440                 "bootm $load_addr#ls1021atwr\0" \
 441         "qspi_bootcmd=echo Trying load from qspi..;"    \
 442                 "sf probe && sf read $load_addr "       \
 443                 "$kernel_addr $kernel_size && bootm $load_addr#$board\0"        \
 444         "nor_bootcmd=echo Trying load from nor..;"      \
 445                 "cp.b $kernel_addr $load_addr "         \
 446                 "$kernel_size && bootm $load_addr#$board\0"
 447 #endif
 448
 449 #undef CONFIG_BOOTCOMMAND
 450 #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
 451 #define CONFIG_BOOTCOMMAND "run distro_bootcmd;run qspi_bootcmd"
 452 #else
 453 #define CONFIG_BOOTCOMMAND "run distro_bootcmd;run nor_bootcmd"
 454 #endif
 455
 456 #define CONFIG_BOOTARGS                 "console=ttyS0,115200 root=/dev/ram0"
 457
 458 /*
 459  * Miscellaneous configurable options
 460  */
 461 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 462 #define CONFIG_AUTO_COMPLETE
 463 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size */
 464 #define CONFIG_SYS_PBSIZE               \
 465                 (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 466 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 467 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 468
 469 #define CONFIG_SYS_MEMTEST_START        0x80000000
 470 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
 471
 472 #define CONFIG_SYS_LOAD_ADDR            0x82000000
 473
 474 #define CONFIG_LS102XA_STREAM_ID
 475
 476 #define CONFIG_SYS_INIT_SP_OFFSET \
 477         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 478 #define CONFIG_SYS_INIT_SP_ADDR \
 479         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 480
 481 #ifdef CONFIG_SPL_BUILD
 482 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 483 #else
 484 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 485 #endif
 486
 487 #define CONFIG_SYS_QE_FW_ADDR     0x60940000
 488
 489 /*
 490  * Environment
 491  */
 492 #define CONFIG_ENV_OVERWRITE
 493
 494 #if defined(CONFIG_SD_BOOT)
 495 #define CONFIG_ENV_OFFSET               0x300000
 496 #define CONFIG_SYS_MMC_ENV_DEV          0
 497 #define CONFIG_ENV_SIZE                 0x20000
 498 #elif defined(CONFIG_QSPI_BOOT)
 499 #define CONFIG_ENV_SIZE                 0x2000
 500 #define CONFIG_ENV_OFFSET               0x300000
 501 #define CONFIG_ENV_SECT_SIZE            0x10000
 502 #else
 503 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
 504 #define CONFIG_ENV_SIZE                 0x20000
 505 #define CONFIG_ENV_SECT_SIZE            0x20000 /* 128K (one sector) */
 506 #endif
 507
 508 #define CONFIG_MISC_INIT_R
 509
 510 #include <asm/fsl_secure_boot.h>
 511 #define CONFIG_SYS_BOOTM_LEN    (64 << 20) /* Increase max gunzip size */
 512
 513 #endif