include/configs/ls1043a_common.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1043A_COMMON_H
   8 #define __LS1043A_COMMON_H
   9
  10 #define CONFIG_REMAKE_ELF
  11 #define CONFIG_FSL_LAYERSCAPE
  12 #define CONFIG_FSL_LSCH2
  13 #define CONFIG_LS1043A
  14 #define CONFIG_MP
  15 #define CONFIG_SYS_FSL_CLK
  16 #define CONFIG_GICV2
  17
  18 #include <asm/arch/config.h>
  19 #ifdef CONFIG_SYS_FSL_SRDS_1
  20 #define CONFIG_SYS_HAS_SERDES
  21 #endif
  22
  23 /* Link Definitions */
  24 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  25
  26 #define CONFIG_SUPPORT_RAW_INITRD
  27
  28 #define CONFIG_SKIP_LOWLEVEL_INIT
  29 #define CONFIG_BOARD_EARLY_INIT_F       1
  30
  31 /* Flat Device Tree Definitions */
  32 #define CONFIG_OF_LIBFDT
  33 #define CONFIG_OF_BOARD_SETUP
  34
  35 /* new uImage format support */
  36 #define CONFIG_FIT
  37 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
  38
  39 #ifndef CONFIG_SYS_FSL_DDR4
  40 #define CONFIG_SYS_FSL_DDR3             /* Use DDR3 memory */
  41 #endif
  42
  43 #define CONFIG_VERY_BIG_RAM
  44 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  45 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  46 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  47
  48 #define CPU_RELEASE_ADDR               secondary_boot_func
  49
  50 /* Generic Timer Definitions */
  51 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  52
  53 /* Size of malloc() pool */
  54 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  55
  56 /* Serial Port */
  57 #define CONFIG_CONS_INDEX               1
  58 #define CONFIG_SYS_NS16550_SERIAL
  59 #define CONFIG_SYS_NS16550_REG_SIZE     1
  60 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0))
  61
  62 #define CONFIG_BAUDRATE                 115200
  63 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  64
  65 /* SD boot SPL */
  66 #ifdef CONFIG_SD_BOOT
  67 #define CONFIG_SPL_FRAMEWORK
  68 #define CONFIG_SPL_LDSCRIPT             "arch/arm/cpu/armv8/u-boot-spl.lds"
  69 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
  70 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  71 #define CONFIG_SPL_LIBGENERIC_SUPPORT
  72 #define CONFIG_SPL_ENV_SUPPORT
  73 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
  74 #define CONFIG_SPL_WATCHDOG_SUPPORT
  75 #define CONFIG_SPL_I2C_SUPPORT
  76 #define CONFIG_SPL_SERIAL_SUPPORT
  77 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  78 #define CONFIG_SPL_MMC_SUPPORT
  79 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR         0xf0
  80 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS              0x500
  81
  82 #define CONFIG_SPL_TEXT_BASE            0x10000000
  83 #define CONFIG_SPL_MAX_SIZE             0x1d000
  84 #define CONFIG_SPL_STACK                0x1001e000
  85 #define CONFIG_SPL_PAD_TO               0x1d000
  86
  87 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE + \
  88                                         CONFIG_SYS_MONITOR_LEN)
  89 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  90 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
  91 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  92 #define CONFIG_SYS_MONITOR_LEN          0xa0000
  93 #endif
  94
  95 /* NAND SPL */
  96 #ifdef CONFIG_NAND_BOOT
  97 #define CONFIG_SPL_PBL_PAD
  98 #define CONFIG_SPL_FRAMEWORK
  99 #define CONFIG_SPL_LDSCRIPT             "arch/arm/cpu/armv8/u-boot-spl.lds"
 100 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
 101 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 102 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 103 #define CONFIG_SPL_ENV_SUPPORT
 104 #define CONFIG_SPL_WATCHDOG_SUPPORT
 105 #define CONFIG_SPL_I2C_SUPPORT
 106 #define CONFIG_SPL_SERIAL_SUPPORT
 107 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
 108 #define CONFIG_SPL_NAND_SUPPORT
 109 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 110 #define CONFIG_SPL_TEXT_BASE            0x10000000
 111 #define CONFIG_SPL_MAX_SIZE             0x1a000
 112 #define CONFIG_SPL_STACK                0x1001d000
 113 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
 114 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 115 #define CONFIG_SYS_SPL_MALLOC_START     0x80200000
 116 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
 117 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 118 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 119 #define CONFIG_SYS_MONITOR_LEN          0xa0000
 120 #endif
 121
 122 /* IFC */
 123 #define CONFIG_FSL_IFC
 124 /*
 125  * CONFIG_SYS_FLASH_BASE has the final address (core view)
 126  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
 127  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
 128  * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
 129  */
 130 #define CONFIG_SYS_FLASH_BASE                   0x60000000
 131 #define CONFIG_SYS_FLASH_BASE_PHYS              CONFIG_SYS_FLASH_BASE
 132 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
 133
 134 #ifndef CONFIG_SYS_NO_FLASH
 135 #define CONFIG_FLASH_CFI_DRIVER
 136 #define CONFIG_SYS_FLASH_CFI
 137 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 138 #define CONFIG_SYS_FLASH_QUIET_TEST
 139 #define CONFIG_FLASH_SHOW_PROGRESS      45      /* count down from 45/5: 9..1 */
 140 #endif
 141
 142 /* I2C */
 143 #define CONFIG_CMD_I2C
 144 #define CONFIG_SYS_I2C
 145 #define CONFIG_SYS_I2C_MXC
 146 #define CONFIG_SYS_I2C_MXC_I2C1
 147 #define CONFIG_SYS_I2C_MXC_I2C2
 148 #define CONFIG_SYS_I2C_MXC_I2C3
 149 #define CONFIG_SYS_I2C_MXC_I2C4
 150
 151 /* PCIe */
 152 #define CONFIG_PCI              /* Enable PCI/PCIE */
 153 #define CONFIG_PCIE1            /* PCIE controller 1 */
 154 #define CONFIG_PCIE2            /* PCIE controller 2 */
 155 #define CONFIG_PCIE3            /* PCIE controller 3 */
 156 #define CONFIG_PCIE_LAYERSCAPE  /* Use common FSL Layerscape PCIe code */
 157 #define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
 158
 159 #define CONFIG_SYS_PCI_64BIT
 160
 161 #define CONFIG_SYS_PCIE_CFG0_PHYS_OFF   0x00000000
 162 #define CONFIG_SYS_PCIE_CFG0_SIZE       0x00001000      /* 4k */
 163 #define CONFIG_SYS_PCIE_CFG1_PHYS_OFF   0x00001000
 164 #define CONFIG_SYS_PCIE_CFG1_SIZE       0x00001000      /* 4k */
 165
 166 #define CONFIG_SYS_PCIE_IO_BUS          0x00000000
 167 #define CONFIG_SYS_PCIE_IO_PHYS_OFF     0x00010000
 168 #define CONFIG_SYS_PCIE_IO_SIZE         0x00010000      /* 64k */
 169
 170 #define CONFIG_SYS_PCIE_MEM_BUS         0x40000000
 171 #define CONFIG_SYS_PCIE_MEM_PHYS_OFF    0x40000000
 172 #define CONFIG_SYS_PCIE_MEM_SIZE        0x40000000      /* 1G */
 173
 174 #ifdef CONFIG_PCI
 175 #define CONFIG_NET_MULTI
 176 #define CONFIG_PCI_PNP
 177 #define CONFIG_E1000
 178 #define CONFIG_PCI_SCAN_SHOW
 179 #define CONFIG_CMD_PCI
 180 #endif
 181
 182 /* Command line configuration */
 183 #define CONFIG_CMD_CACHE
 184 #define CONFIG_CMD_DHCP
 185 #define CONFIG_CMD_ENV
 186 #define CONFIG_CMD_PING
 187
 188 /*  MMC  */
 189 #define CONFIG_MMC
 190 #ifdef CONFIG_MMC
 191 #define CONFIG_CMD_MMC
 192 #define CONFIG_CMD_FAT
 193 #define CONFIG_FSL_ESDHC
 194 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 195 #define CONFIG_GENERIC_MMC
 196 #define CONFIG_DOS_PARTITION
 197 #endif
 198
 199 /* FMan ucode */
 200 #define CONFIG_SYS_DPAA_FMAN
 201 #ifdef CONFIG_SYS_DPAA_FMAN
 202 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 203
 204 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 205 /* FMan fireware Pre-load address */
 206 #define CONFIG_SYS_FMAN_FW_ADDR         0x60300000
 207 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 208 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 209 #endif
 210
 211 /* Miscellaneous configurable options */
 212 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 213 #define CONFIG_ARCH_EARLY_INIT_R
 214 #define CONFIG_BOARD_LATE_INIT
 215
 216 #define CONFIG_HWCONFIG
 217 #define HWCONFIG_BUFFER_SIZE            128
 218
 219 /* Initial environment variables */
 220 #define CONFIG_EXTRA_ENV_SETTINGS               \
 221         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 222         "loadaddr=0x80100000\0"                 \
 223         "kernel_addr=0x100000\0"                \
 224         "ramdisk_addr=0x800000\0"               \
 225         "ramdisk_size=0x2000000\0"              \
 226         "fdt_high=0xffffffffffffffff\0"         \
 227         "initrd_high=0xffffffffffffffff\0"      \
 228         "kernel_start=0x61200000\0"             \
 229         "kernel_load=0x807f0000\0"              \
 230         "kernel_size=0x1000000\0"               \
 231         "console=ttyAMA0,38400n8\0"
 232
 233 #define CONFIG_BOOTARGS                 "console=ttyS0,115200 root=/dev/ram0 " \
 234                                         "earlycon=uart8250,0x21c0500,115200"
 235 #define CONFIG_BOOTCOMMAND              "cp.b $kernel_start $kernel_load "     \
 236                                         "$kernel_size && bootm $kernel_load"
 237 #define CONFIG_BOOTDELAY                10
 238
 239 /* Monitor Command Prompt */
 240 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 241 #define CONFIG_SYS_PROMPT               "=> "
 242 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 243                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 244 #define CONFIG_SYS_HUSH_PARSER
 245 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 246 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot args buffer */
 247 #define CONFIG_SYS_LONGHELP
 248 #define CONFIG_CMDLINE_EDITING          1
 249 #define CONFIG_AUTO_COMPLETE
 250 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 251
 252 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 253
 254 #endif /* __LS1043A_COMMON_H */