include/configs/ls1088a_common.h

   1 /*
   2  * Copyright 2017 NXP
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1088_COMMON_H
   8 #define __LS1088_COMMON_H
   9
  10
  11 #define CONFIG_REMAKE_ELF
  12 #define CONFIG_FSL_LAYERSCAPE
  13 #define CONFIG_MP
  14
  15 #include <asm/arch/stream_id_lsch3.h>
  16 #include <asm/arch/config.h>
  17 #include <asm/arch/soc.h>
  18
  19 /* Link Definitions */
  20 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  21
  22 /* Link Definitions */
  23 #ifdef CONFIG_QSPI_BOOT
  24 #define CONFIG_SYS_TEXT_BASE            0x20100000
  25 #else
  26 #define CONFIG_SYS_TEXT_BASE            0x30100000
  27 #endif
  28
  29 #define CONFIG_SUPPORT_RAW_INITRD
  30
  31
  32 #define CONFIG_SKIP_LOWLEVEL_INIT
  33
  34 #define CONFIG_FSL_DDR_INTERACTIVE      /* Interactive debugging */
  35
  36 #define CONFIG_VERY_BIG_RAM
  37 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000UL
  38 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  39 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  40 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x8080000000ULL
  41 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS       1
  42 /*
  43  * SMP Definitinos
  44  */
  45 #define CPU_RELEASE_ADDR                secondary_boot_func
  46
  47 #ifdef CONFIG_PCI
  48 #define CONFIG_CMD_PCI
  49 #endif
  50
  51 /* Size of malloc() pool */
  52 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2048 * 1024)
  53
  54 /* I2C */
  55 #define CONFIG_SYS_I2C
  56 #define CONFIG_SYS_I2C_MXC
  57 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  58 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  59 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  60 #define CONFIG_SYS_I2C_MXC_I2C4         /* enable I2C bus 4 */
  61
  62 /* Serial Port */
  63 #define CONFIG_CONS_INDEX       1
  64 #define CONFIG_SYS_NS16550_SERIAL
  65 #define CONFIG_SYS_NS16550_REG_SIZE     1
  66 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)
  67
  68 #define CONFIG_BAUDRATE                 115200
  69 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  70
  71 /* IFC */
  72 #define CONFIG_FSL_IFC
  73
  74 /*
  75  * During booting, IFC is mapped at the region of 0x30000000.
  76  * But this region is limited to 256MB. To accommodate NOR, promjet
  77  * and FPGA. This region is divided as below:
  78  * 0x30000000 - 0x37ffffff : 128MB : NOR flash
  79  * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
  80  * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
  81  *
  82  * To accommodate bigger NOR flash and other devices, we will map IFC
  83  * chip selects to as below:
  84  * 0x5_1000_0000..0x5_1fff_ffff Memory Hole
  85  * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
  86  * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
  87  * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
  88  * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
  89  *
  90  * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
  91  * CONFIG_SYS_FLASH_BASE has the final address (core view)
  92  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
  93  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
  94  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
  95  */
  96
  97 #define CONFIG_SYS_FLASH_BASE                   0x580000000ULL
  98 #define CONFIG_SYS_FLASH_BASE_PHYS              0x80000000
  99 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
 100
 101 #define CONFIG_SYS_FLASH1_BASE_PHYS             0xC0000000
 102 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY       0x8000000
 103
 104 #ifndef __ASSEMBLY__
 105 unsigned long long get_qixis_addr(void);
 106 #endif
 107
 108 #define QIXIS_BASE                              get_qixis_addr()
 109 #define QIXIS_BASE_PHYS                         0x20000000
 110 #define QIXIS_BASE_PHYS_EARLY                   0xC000000
 111
 112
 113 #define CONFIG_SYS_NAND_BASE                    0x530000000ULL
 114 #define CONFIG_SYS_NAND_BASE_PHYS               0x30000000
 115
 116
 117 /* MC firmware */
 118 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
 119 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH     0x20000
 120 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
 121 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH     0x20000
 122 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
 123 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH    0x200000
 124 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET   0x07000000
 125
 126 /* Define phy_reset function to boot the MC based on mcinitcmd.
 127  * This happens late enough to properly fixup u-boot env MAC addresses.
 128  */
 129 #define CONFIG_RESET_PHY_R
 130
 131 /*
 132  * Carve out a DDR region which will not be used by u-boot/Linux
 133  *
 134  * It will be used by MC and Debug Server. The MC region must be
 135  * 512MB aligned, so the min size to hide is 512MB.
 136  */
 137
 138 #if defined(CONFIG_FSL_MC_ENET)
 139 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE            (512UL * 1024 * 1024)
 140 #endif
 141
 142 #define CONFIG_FSL_CAAM                 /* Enable SEC/CAAM */
 143
 144 /* Command line configuration */
 145 #define CONFIG_CMD_GREPENV
 146 #define CONFIG_CMD_CACHE
 147
 148 /* Miscellaneous configurable options */
 149 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 150
 151 /* Physical Memory Map */
 152 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
 153
 154 #define CONFIG_NR_DRAM_BANKS            2
 155
 156 #define CONFIG_HWCONFIG
 157 #define HWCONFIG_BUFFER_SIZE            128
 158
 159 /* #define CONFIG_DISPLAY_CPUINFO */
 160
 161 /* Allow to overwrite serial and ethaddr */
 162 #define CONFIG_ENV_OVERWRITE
 163
 164 /* Initial environment variables */
 165 #define CONFIG_EXTRA_ENV_SETTINGS               \
 166         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 167         "loadaddr=0x80100000\0"                 \
 168         "kernel_addr=0x100000\0"                \
 169         "ramdisk_addr=0x800000\0"               \
 170         "ramdisk_size=0x2000000\0"              \
 171         "fdt_high=0xa0000000\0"                 \
 172         "initrd_high=0xffffffffffffffff\0"      \
 173         "kernel_start=0x581000000\0"            \
 174         "kernel_load=0xa0000000\0"              \
 175         "kernel_size=0x2800000\0"               \
 176         "console=ttyAMA0,38400n8\0"             \
 177         "mcinitcmd=fsl_mc start mc 0x580a00000" \
 178         " 0x580e00000 \0"
 179
 180 #define CONFIG_BOOTARGS         "console=ttyS0,115200 root=/dev/ram0 " \
 181                                 "earlycon=uart8250,mmio,0x21c0500 " \
 182                                 "ramdisk_size=0x3000000 default_hugepagesz=2m" \
 183                                 " hugepagesz=2m hugepages=256"
 184 #if defined(CONFIG_QSPI_BOOT)
 185 #define CONFIG_BOOTCOMMAND      "sf probe 0:0;" \
 186                                 "sf read 0x80200000 0xd00000 0x100000;"\
 187                                 " fsl_mc apply dpl 0x80200000 &&" \
 188                                 " sf read $kernel_load $kernel_start" \
 189                                 " $kernel_size && bootm $kernel_load"
 190 #else /* NOR BOOT*/
 191 #define CONFIG_BOOTCOMMAND      "fsl_mc apply dpl 0x580d00000 &&" \
 192                                 " cp.b $kernel_start $kernel_load" \
 193                                 " $kernel_size && bootm $kernel_load"
 194 #endif
 195
 196 /* Monitor Command Prompt */
 197 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 198 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 199                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 200 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 201 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE /* Boot args buffer */
 202 #define CONFIG_SYS_LONGHELP
 203 #define CONFIG_CMDLINE_EDITING          1
 204 #define CONFIG_AUTO_COMPLETE
 205 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 206
 207 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
 208
 209 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 210
 211 #endif /* __LS1088_COMMON_H */