include/configs/ls2080a_common.h

   1 /*
   2  * Copyright 2017 NXP
   3  * Copyright (C) 2014 Freescale Semiconductor
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __LS2_COMMON_H
   9 #define __LS2_COMMON_H
  10
  11 #define CONFIG_REMAKE_ELF
  12 #define CONFIG_FSL_LAYERSCAPE
  13 #define CONFIG_MP
  14 #define CONFIG_GICV3
  15 #define CONFIG_FSL_TZPC_BP147
  16
  17 #include <asm/arch/stream_id_lsch3.h>
  18 #include <asm/arch/config.h>
  19
  20 /* Link Definitions */
  21 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  22
  23 /* We need architecture specific misc initializations */
  24
  25 /* Link Definitions */
  26 #ifndef CONFIG_QSPI_BOOT
  27 #else
  28 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
  29 #define CONFIG_ENV_OFFSET               0x300000        /* 3MB */
  30 #define CONFIG_ENV_SECT_SIZE            0x40000
  31 #endif
  32
  33 #define CONFIG_SKIP_LOWLEVEL_INIT
  34
  35 #ifndef CONFIG_SPL
  36 #define CONFIG_FSL_DDR_INTERACTIVE      /* Interactive debugging */
  37 #endif
  38 #ifndef CONFIG_SYS_FSL_DDR4
  39 #define CONFIG_SYS_DDR_RAW_TIMING
  40 #endif
  41
  42 #define CONFIG_SYS_FSL_DDR_INTLV_256B   /* force 256 byte interleaving */
  43
  44 #define CONFIG_VERY_BIG_RAM
  45 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000UL
  46 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  47 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  48 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x8080000000ULL
  49 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS       2
  50
  51 /*
  52  * SMP Definitinos
  53  */
  54 #define CPU_RELEASE_ADDR                secondary_boot_func
  55
  56 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
  57 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  58 #define CONFIG_SYS_DP_DDR_BASE          0x6000000000ULL
  59 /*
  60  * DDR controller use 0 as the base address for binding.
  61  * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
  62  */
  63 #define CONFIG_SYS_DP_DDR_BASE_PHY      0
  64 #define CONFIG_DP_DDR_CTRL              2
  65 #define CONFIG_DP_DDR_NUM_CTRLS         1
  66 #endif
  67
  68 /* Generic Timer Definitions */
  69 /*
  70  * This is not an accurate number. It is used in start.S. The frequency
  71  * will be udpated later when get_bus_freq(0) is available.
  72  */
  73 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  74
  75 /* Size of malloc() pool */
  76 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 2048 * 1024)
  77
  78 /* I2C */
  79 #define CONFIG_SYS_I2C
  80 #define CONFIG_SYS_I2C_MXC
  81 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  82 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  83 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  84 #define CONFIG_SYS_I2C_MXC_I2C4         /* enable I2C bus 4 */
  85
  86 /* Serial Port */
  87 #define CONFIG_CONS_INDEX       1
  88 #define CONFIG_SYS_NS16550_SERIAL
  89 #define CONFIG_SYS_NS16550_REG_SIZE     1
  90 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  91
  92 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  93
  94 /* IFC */
  95 #define CONFIG_FSL_IFC
  96
  97 /*
  98  * During booting, IFC is mapped at the region of 0x30000000.
  99  * But this region is limited to 256MB. To accommodate NOR, promjet
 100  * and FPGA. This region is divided as below:
 101  * 0x30000000 - 0x37ffffff : 128MB : NOR flash
 102  * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
 103  * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
 104  *
 105  * To accommodate bigger NOR flash and other devices, we will map IFC
 106  * chip selects to as below:
 107  * 0x5_1000_0000..0x5_1fff_ffff Memory Hole
 108  * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
 109  * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
 110  * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
 111  * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
 112  *
 113  * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
 114  * CONFIG_SYS_FLASH_BASE has the final address (core view)
 115  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
 116  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
 117  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
 118  */
 119
 120 #define CONFIG_SYS_FLASH_BASE                   0x580000000ULL
 121 #define CONFIG_SYS_FLASH_BASE_PHYS              0x80000000
 122 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY        0x00000000
 123
 124 #define CONFIG_SYS_FLASH1_BASE_PHYS             0xC0000000
 125 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY       0x8000000
 126
 127 #ifndef __ASSEMBLY__
 128 unsigned long long get_qixis_addr(void);
 129 #endif
 130 #define QIXIS_BASE                              get_qixis_addr()
 131 #define QIXIS_BASE_PHYS                         0x20000000
 132 #define QIXIS_BASE_PHYS_EARLY                   0xC000000
 133 #define QIXIS_STAT_PRES1                        0xb
 134 #define QIXIS_SDID_MASK                         0x07
 135 #define QIXIS_ESDHC_NO_ADAPTER                  0x7
 136
 137 #define CONFIG_SYS_NAND_BASE                    0x530000000ULL
 138 #define CONFIG_SYS_NAND_BASE_PHYS               0x30000000
 139
 140 /* MC firmware */
 141 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
 142 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH     0x20000
 143 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
 144 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH     0x20000
 145 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
 146 /* For LS2085A */
 147 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH    0x200000
 148 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET   0x07000000
 149
 150 /* Define phy_reset function to boot the MC based on mcinitcmd.
 151  * This happens late enough to properly fixup u-boot env MAC addresses.
 152  */
 153 #define CONFIG_RESET_PHY_R
 154
 155 /*
 156  * Carve out a DDR region which will not be used by u-boot/Linux
 157  *
 158  * It will be used by MC and Debug Server. The MC region must be
 159  * 512MB aligned, so the min size to hide is 512MB.
 160  */
 161 #ifdef CONFIG_FSL_MC_ENET
 162 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE            (512UL * 1024 * 1024)
 163 #endif
 164
 165 /* Command line configuration */
 166
 167 /* Miscellaneous configurable options */
 168 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 169
 170 /* Physical Memory Map */
 171 /* fixme: these need to be checked against the board */
 172 #define CONFIG_CHIP_SELECTS_PER_CTRL    4
 173
 174 #define CONFIG_NR_DRAM_BANKS            3
 175
 176 #define CONFIG_HWCONFIG
 177 #define HWCONFIG_BUFFER_SIZE            128
 178
 179 /* Allow to overwrite serial and ethaddr */
 180 #define CONFIG_ENV_OVERWRITE
 181
 182 /* Initial environment variables */
 183 #define CONFIG_EXTRA_ENV_SETTINGS               \
 184         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 185         "loadaddr=0x80100000\0"                 \
 186         "kernel_addr=0x100000\0"                \
 187         "ramdisk_addr=0x800000\0"               \
 188         "ramdisk_size=0x2000000\0"              \
 189         "fdt_high=0xa0000000\0"                 \
 190         "initrd_high=0xffffffffffffffff\0"      \
 191         "kernel_start=0x581000000\0"            \
 192         "kernel_load=0xa0000000\0"              \
 193         "kernel_size=0x2800000\0"               \
 194         "console=ttyAMA0,38400n8\0"             \
 195         "mcinitcmd=fsl_mc start mc 0x580a00000" \
 196         " 0x580e00000 \0"
 197
 198 #ifdef CONFIG_SD_BOOT
 199 #define CONFIG_BOOTCOMMAND      "mmc read 0x80200000 0x6800 0x800;"\
 200                                 " fsl_mc apply dpl 0x80200000 &&" \
 201                                 " mmc read $kernel_load $kernel_start" \
 202                                 " $kernel_size && bootm $kernel_load"
 203 #else
 204 #define CONFIG_BOOTCOMMAND      "fsl_mc apply dpl 0x580d00000 &&" \
 205                                 " cp.b $kernel_start $kernel_load" \
 206                                 " $kernel_size && bootm $kernel_load"
 207 #endif
 208
 209 /* Monitor Command Prompt */
 210 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 211 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 212
 213 #define CONFIG_SPL_BSS_START_ADDR       0x80100000
 214 #define CONFIG_SPL_BSS_MAX_SIZE         0x00100000
 215 #define CONFIG_SPL_MAX_SIZE             0x16000
 216 #define CONFIG_SPL_STACK                (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
 217 #define CONFIG_SPL_TARGET               "u-boot-with-spl.bin"
 218 #define CONFIG_SPL_TEXT_BASE            0x1800a000
 219
 220 #ifdef CONFIG_NAND_BOOT
 221 #define CONFIG_SYS_NAND_U_BOOT_DST      0x80400000
 222 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
 223 #endif
 224 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x00100000
 225 #define CONFIG_SYS_SPL_MALLOC_START     0x80200000
 226 #define CONFIG_SYS_MONITOR_LEN          (1024 * 1024)
 227
 228 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 229
 230 #include <asm/arch/soc.h>
 231
 232 #endif /* __LS2_COMMON_H */