include/configs/ls2080ardb.h

   1 /*
   2  * Copyright 2017 NXP
   3  * Copyright 2015 Freescale Semiconductor
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __LS2_RDB_H
   9 #define __LS2_RDB_H
  10
  11 #include "ls2080a_common.h"
  12
  13 #undef CONFIG_CONS_INDEX
  14 #define CONFIG_CONS_INDEX       2
  15
  16 #ifdef CONFIG_FSL_QSPI
  17 #ifdef CONFIG_TARGET_LS2081ARDB
  18 #define CONFIG_QIXIS_I2C_ACCESS
  19 #endif
  20 #define CONFIG_SYS_I2C_EARLY_INIT
  21 #define CONFIG_DISPLAY_BOARDINFO_LATE
  22 #endif
  23
  24 #define I2C_MUX_CH_VOL_MONITOR          0xa
  25 #define I2C_VOL_MONITOR_ADDR            0x38
  26 #define CONFIG_VOL_MONITOR_IR36021_READ
  27 #define CONFIG_VOL_MONITOR_IR36021_SET
  28
  29 #define CONFIG_VID_FLS_ENV              "ls2080ardb_vdd_mv"
  30 #ifndef CONFIG_SPL_BUILD
  31 #define CONFIG_VID
  32 #endif
  33 /* step the IR regulator in 5mV increments */
  34 #define IR_VDD_STEP_DOWN                5
  35 #define IR_VDD_STEP_UP                  5
  36 /* The lowest and highest voltage allowed for LS2080ARDB */
  37 #define VDD_MV_MIN                      819
  38 #define VDD_MV_MAX                      1212
  39
  40 #ifndef __ASSEMBLY__
  41 unsigned long get_board_sys_clk(void);
  42 #endif
  43
  44 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  45 #define CONFIG_DDR_CLK_FREQ             133333333
  46 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ/4)
  47
  48 #define CONFIG_DDR_SPD
  49 #define CONFIG_DDR_ECC
  50 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  51 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  52 #define SPD_EEPROM_ADDRESS1     0x51
  53 #define SPD_EEPROM_ADDRESS2     0x52
  54 #define SPD_EEPROM_ADDRESS3     0x53
  55 #define SPD_EEPROM_ADDRESS4     0x54
  56 #define SPD_EEPROM_ADDRESS5     0x55
  57 #define SPD_EEPROM_ADDRESS6     0x56    /* dummy address */
  58 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  59 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  60 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  61 #define CONFIG_CHIP_SELECTS_PER_CTRL            4
  62 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  63 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  64 #endif
  65 #define CONFIG_FSL_DDR_BIST     /* enable built-in memory test */
  66
  67 /* SATA */
  68 #define CONFIG_LIBATA
  69 #define CONFIG_SCSI_AHCI
  70 #define CONFIG_SCSI_AHCI_PLAT
  71 #define CONFIG_SCSI
  72
  73 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  74 #define CONFIG_SYS_SATA2                        AHCI_BASE_ADDR2
  75
  76 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  77 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  78 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  79                                                 CONFIG_SYS_SCSI_MAX_LUN)
  80
  81 #ifndef CONFIG_FSL_QSPI
  82 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
  83
  84 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  85 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128*1024*1024)
  86 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64*1024*1024)
  87
  88 #define CONFIG_SYS_NOR0_CSPR                                    \
  89         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  90         CSPR_PORT_SIZE_16                                       | \
  91         CSPR_MSEL_NOR                                           | \
  92         CSPR_V)
  93 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  94         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  95         CSPR_PORT_SIZE_16                                       | \
  96         CSPR_MSEL_NOR                                           | \
  97         CSPR_V)
  98 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
  99 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 100                                 FTIM0_NOR_TEADC(0x5) | \
 101                                 FTIM0_NOR_TEAHC(0x5))
 102 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 103                                 FTIM1_NOR_TRAD_NOR(0x1a) |\
 104                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 105 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 106                                 FTIM2_NOR_TCH(0x4) | \
 107                                 FTIM2_NOR_TWPH(0x0E) | \
 108                                 FTIM2_NOR_TWP(0x1c))
 109 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 110 #define CONFIG_SYS_IFC_CCR      0x01000000
 111
 112 #ifdef CONFIG_MTD_NOR_FLASH
 113 #define CONFIG_FLASH_CFI_DRIVER
 114 #define CONFIG_SYS_FLASH_CFI
 115 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 116 #define CONFIG_SYS_FLASH_QUIET_TEST
 117 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 118
 119 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 120 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 121 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 122 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 123
 124 #define CONFIG_SYS_FLASH_EMPTY_INFO
 125 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE,\
 126                                          CONFIG_SYS_FLASH_BASE + 0x40000000}
 127 #endif
 128
 129 #define CONFIG_NAND_FSL_IFC
 130 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 131 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 132
 133 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 134 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 135                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 136                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 137                                 | CSPR_V)
 138 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 139
 140 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 141                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 142                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 143                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 144                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 145                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 146                                 | CSOR_NAND_PB(128))    /* Pages Per Block 128*/
 147
 148 #define CONFIG_SYS_NAND_ONFI_DETECTION
 149
 150 /* ONFI NAND Flash mode0 Timing Params */
 151 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x0e) | \
 152                                         FTIM0_NAND_TWP(0x30)   | \
 153                                         FTIM0_NAND_TWCHT(0x0e) | \
 154                                         FTIM0_NAND_TWH(0x14))
 155 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x64) | \
 156                                         FTIM1_NAND_TWBE(0xab)  | \
 157                                         FTIM1_NAND_TRR(0x1c)   | \
 158                                         FTIM1_NAND_TRP(0x30))
 159 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x1e) | \
 160                                         FTIM2_NAND_TREH(0x14) | \
 161                                         FTIM2_NAND_TWHRE(0x3c))
 162 #define CONFIG_SYS_NAND_FTIM3           0x0
 163
 164 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 165 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 166 #define CONFIG_MTD_NAND_VERIFY_WRITE
 167 #define CONFIG_CMD_NAND
 168
 169 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 170 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 171 #define QIXIS_LBMAP_SWITCH              0x06
 172 #define QIXIS_LBMAP_MASK                0x0f
 173 #define QIXIS_LBMAP_SHIFT               0
 174 #define QIXIS_LBMAP_DFLTBANK            0x00
 175 #define QIXIS_LBMAP_ALTBANK             0x04
 176 #define QIXIS_LBMAP_NAND                0x09
 177 #define QIXIS_RST_CTL_RESET             0x31
 178 #define QIXIS_RST_CTL_RESET_EN          0x30
 179 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 180 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 181 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 182 #define QIXIS_RCW_SRC_NAND              0x119
 183 #define QIXIS_RST_FORCE_MEM             0x01
 184
 185 #define CONFIG_SYS_CSPR3_EXT    (0x0)
 186 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 187                                 | CSPR_PORT_SIZE_8 \
 188                                 | CSPR_MSEL_GPCM \
 189                                 | CSPR_V)
 190 #define CONFIG_SYS_CSPR3_FINAL  (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 191                                 | CSPR_PORT_SIZE_8 \
 192                                 | CSPR_MSEL_GPCM \
 193                                 | CSPR_V)
 194
 195 #define CONFIG_SYS_AMASK3       IFC_AMASK(64*1024)
 196 #define CONFIG_SYS_CSOR3        CSOR_GPCM_ADM_SHIFT(12)
 197 /* QIXIS Timing parameters for IFC CS3 */
 198 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 199                                         FTIM0_GPCM_TEADC(0x0e) | \
 200                                         FTIM0_GPCM_TEAHC(0x0e))
 201 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 202                                         FTIM1_GPCM_TRAD(0x3f))
 203 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0xf) | \
 204                                         FTIM2_GPCM_TCH(0xf) | \
 205                                         FTIM2_GPCM_TWP(0x3E))
 206 #define CONFIG_SYS_CS3_FTIM3            0x0
 207
 208 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
 209 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 210 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR_EARLY
 211 #define CONFIG_SYS_CSPR2_FINAL          CONFIG_SYS_NOR0_CSPR
 212 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 213 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 214 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 215 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 216 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 217 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 218 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 219 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 220 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 221 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 222 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 223 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 224 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 225 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 226
 227 #define CONFIG_ENV_IS_IN_NAND
 228 #define CONFIG_ENV_OFFSET               (2048 * 1024)
 229 #define CONFIG_ENV_SECT_SIZE            0x20000
 230 #define CONFIG_ENV_SIZE                 0x2000
 231 #define CONFIG_SPL_PAD_TO               0x80000
 232 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (1024 * 1024)
 233 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (512 * 1024)
 234 #else
 235 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 236 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 237 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 238 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 239 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 240 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 241 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 242 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 243 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 244 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 245 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 246 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 247 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 248 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 249 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 250 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 251 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 252
 253 #define CONFIG_ENV_IS_IN_FLASH
 254 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
 255 #define CONFIG_ENV_SECT_SIZE            0x20000
 256 #define CONFIG_ENV_SIZE                 0x2000
 257 #endif
 258
 259 /* Debug Server firmware */
 260 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 261 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
 262 #endif
 263 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 264
 265 #ifdef CONFIG_TARGET_LS2081ARDB
 266 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 267 #define QIXIS_QMAP_MASK                 0x07
 268 #define QIXIS_QMAP_SHIFT                5
 269 #define QIXIS_LBMAP_DFLTBANK            0x00
 270 #define QIXIS_LBMAP_QSPI                0x00
 271 #define QIXIS_RCW_SRC_QSPI              0x62
 272 #define QIXIS_LBMAP_ALTBANK             0x20
 273 #define QIXIS_RST_CTL_RESET             0x31
 274 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 275 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 276 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 277 #define QIXIS_LBMAP_MASK                0x0f
 278 #define QIXIS_RST_CTL_RESET_EN          0x30
 279 #endif
 280
 281 /*
 282  * I2C
 283  */
 284 #ifdef CONFIG_TARGET_LS2081ARDB
 285 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 286 #endif
 287 #define I2C_MUX_PCA_ADDR                0x75
 288 #define I2C_MUX_PCA_ADDR_PRI            0x75 /* Primary Mux*/
 289
 290 /* I2C bus multiplexer */
 291 #define I2C_MUX_CH_DEFAULT      0x8
 292
 293 /* SPI */
 294 #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
 295 #define CONFIG_SPI_FLASH
 296 #ifdef CONFIG_FSL_QSPI
 297 #define CONFIG_SPI_FLASH_STMICRO
 298 #endif
 299 #ifdef CONFIG_FSL_QSPI
 300 #ifdef CONFIG_TARGET_LS2081ARDB
 301 #define CONFIG_SPI_FLASH_STMICRO
 302 #else
 303 #define CONFIG_SPI_FLASH_SPANSION
 304 #endif
 305 #define FSL_QSPI_FLASH_SIZE             SZ_64M  /* 64MB */
 306 #define FSL_QSPI_FLASH_NUM              2
 307 #endif
 308 #endif
 309
 310 /*
 311  * RTC configuration
 312  */
 313 #define RTC
 314 #ifdef CONFIG_TARGET_LS2081ARDB
 315 #define CONFIG_RTC_PCF8563              1
 316 #define CONFIG_SYS_I2C_RTC_ADDR         0x51
 317 #else
 318 #define CONFIG_RTC_DS3231               1
 319 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 320 #endif
 321
 322 /* EEPROM */
 323 #define CONFIG_ID_EEPROM
 324 #define CONFIG_SYS_I2C_EEPROM_NXID
 325 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 326 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 327 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 328 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 329 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 330
 331 #define CONFIG_FSL_MEMAC
 332
 333 #ifdef CONFIG_PCI
 334 #define CONFIG_PCI_SCAN_SHOW
 335 #define CONFIG_CMD_PCI
 336 #endif
 337
 338 /*  MMC  */
 339 #ifdef CONFIG_MMC
 340 #define CONFIG_FSL_ESDHC
 341 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 342 #endif
 343
 344 #define CONFIG_MISC_INIT_R
 345
 346 /*
 347  * USB
 348  */
 349 #define CONFIG_HAS_FSL_XHCI_USB
 350 #define CONFIG_USB_XHCI_FSL
 351 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 352 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 353
 354 #undef CONFIG_CMDLINE_EDITING
 355 #include <config_distro_defaults.h>
 356
 357 #define BOOT_TARGET_DEVICES(func) \
 358         func(USB, usb, 0) \
 359         func(MMC, mmc, 0) \
 360         func(SCSI, scsi, 0) \
 361         func(DHCP, dhcp, na)
 362 #include <config_distro_bootcmd.h>
 363
 364 /* Initial environment variables */
 365 #undef CONFIG_EXTRA_ENV_SETTINGS
 366 #ifdef CONFIG_SECURE_BOOT
 367 #define CONFIG_EXTRA_ENV_SETTINGS               \
 368         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 369         "scriptaddr=0x80800000\0"               \
 370         "kernel_addr_r=0x81000000\0"            \
 371         "pxefile_addr_r=0x81000000\0"           \
 372         "fdt_addr_r=0x88000000\0"               \
 373         "ramdisk_addr_r=0x89000000\0"           \
 374         "loadaddr=0x80100000\0"                 \
 375         "kernel_addr=0x100000\0"                \
 376         "ramdisk_addr=0x800000\0"               \
 377         "ramdisk_size=0x2000000\0"              \
 378         "fdt_high=0xa0000000\0"                 \
 379         "initrd_high=0xffffffffffffffff\0"      \
 380         "kernel_start=0x581000000\0"            \
 381         "kernel_load=0xa0000000\0"              \
 382         "kernel_size=0x2800000\0"               \
 383         "mcmemsize=0x40000000\0"                \
 384         "fdtfile=fsl-ls2080a-rdb.dtb\0"         \
 385         "mcinitcmd=esbc_validate 0x580700000;"  \
 386         "esbc_validate 0x580740000;"            \
 387         "fsl_mc start mc 0x580a00000"           \
 388         " 0x580e00000 \0"                       \
 389         BOOTENV
 390 #else
 391 #ifdef CONFIG_QSPI_BOOT
 392 #define CONFIG_EXTRA_ENV_SETTINGS               \
 393         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 394         "scriptaddr=0x80800000\0"               \
 395         "kernel_addr_r=0x81000000\0"            \
 396         "pxefile_addr_r=0x81000000\0"           \
 397         "fdt_addr_r=0x88000000\0"               \
 398         "ramdisk_addr_r=0x89000000\0"           \
 399         "loadaddr=0x80100000\0"                 \
 400         "kernel_addr=0x100000\0"                \
 401         "ramdisk_size=0x2000000\0"              \
 402         "fdt_high=0xa0000000\0"                 \
 403         "initrd_high=0xffffffffffffffff\0"      \
 404         "kernel_start=0x21000000\0"             \
 405         "mcmemsize=0x40000000\0"                \
 406         "mcinitcmd=fsl_mc start mc 0x20a00000" \
 407         " 0x20e00000 \0"                       \
 408         BOOTENV
 409 #else
 410 #define CONFIG_EXTRA_ENV_SETTINGS               \
 411         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 412         "scriptaddr=0x80800000\0"               \
 413         "kernel_addr_r=0x81000000\0"            \
 414         "pxefile_addr_r=0x81000000\0"           \
 415         "fdt_addr_r=0x88000000\0"               \
 416         "ramdisk_addr_r=0x89000000\0"           \
 417         "loadaddr=0x80100000\0"                 \
 418         "kernel_addr=0x100000\0"                \
 419         "ramdisk_addr=0x800000\0"               \
 420         "ramdisk_size=0x2000000\0"              \
 421         "fdt_high=0xa0000000\0"                 \
 422         "initrd_high=0xffffffffffffffff\0"      \
 423         "kernel_start=0x581000000\0"            \
 424         "kernel_load=0xa0000000\0"              \
 425         "kernel_size=0x2800000\0"               \
 426         "mcmemsize=0x40000000\0"                \
 427         "fdtfile=fsl-ls2080a-rdb.dtb\0"         \
 428         "mcinitcmd=fsl_mc start mc 0x580a00000" \
 429         " 0x580e00000 \0"                       \
 430         BOOTENV
 431 #endif
 432 #endif
 433
 434
 435 #undef CONFIG_BOOTARGS
 436 #define CONFIG_BOOTARGS         "console=ttyS1,115200 root=/dev/ram0 " \
 437                                 "earlycon=uart8250,mmio,0x21c0600 " \
 438                                 "ramdisk_size=0x2000000 default_hugepagesz=2m" \
 439                                 " hugepagesz=2m hugepages=256"
 440
 441 #undef CONFIG_BOOTCOMMAND
 442 #ifdef CONFIG_QSPI_BOOT
 443 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 444 #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x20d00000" \
 445                            " && bootm $kernel_start" \
 446                            " || run distro_bootcmd"
 447 #else
 448 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 449 #define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580d00000" \
 450                            " && cp.b $kernel_start $kernel_load $kernel_size" \
 451                            " && bootm $kernel_load" \
 452                            " || run distro_bootcmd"
 453 #endif
 454
 455 /* MAC/PHY configuration */
 456 #ifdef CONFIG_FSL_MC_ENET
 457 #define CONFIG_PHYLIB_10G
 458 #define CONFIG_PHY_AQUANTIA
 459 #define CONFIG_PHY_CORTINA
 460 #define CONFIG_PHYLIB
 461 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 462 #ifdef CONFIG_QSPI_BOOT
 463 #define CONFIG_CORTINA_FW_ADDR          0x20980000
 464 #else
 465 #define CONFIG_CORTINA_FW_ADDR          0x580980000
 466 #endif
 467 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 468
 469 #define CORTINA_PHY_ADDR1       0x10
 470 #define CORTINA_PHY_ADDR2       0x11
 471 #define CORTINA_PHY_ADDR3       0x12
 472 #define CORTINA_PHY_ADDR4       0x13
 473 #define AQ_PHY_ADDR1            0x00
 474 #define AQ_PHY_ADDR2            0x01
 475 #define AQ_PHY_ADDR3            0x02
 476 #define AQ_PHY_ADDR4            0x03
 477 #define AQR405_IRQ_MASK         0x36
 478
 479 #define CONFIG_MII
 480 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 481 #define CONFIG_PHY_GIGE
 482 #define CONFIG_PHY_AQUANTIA
 483 #endif
 484
 485 #include <asm/fsl_secure_boot.h>
 486
 487 #endif /* __LS2_RDB_H */