include/configs/mecp5123.h

   1 /*
   2  * (C) Copyright 2009 Wolfgang Denk <wd@denx.de>
   3  * (C) Copyright 2009, DAVE Srl <www.dave.eu>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  * modifications for the MECP5123 by reinhard.arlt@esd-electronics.com
   7  *
   8  */
   9
  10 /*
  11  * MECP5123 board configuration file
  12  */
  13
  14 #ifndef __CONFIG_H
  15 #define __CONFIG_H
  16
  17 #define CONFIG_MECP5123 1
  18
  19 /*
  20  * Memory map for the MECP5123 board:
  21  *
  22  * 0x0000_0000 - 0x1FFF_FFFF    DDR RAM (512 MB)
  23  * 0x3000_0000 - 0x3001_FFFF    SRAM (128 KB)
  24  * 0x8000_0000 - 0x803F_FFFF    IMMR (4 MB)
  25  * 0x8200_0000 - 0x8200_FFFF    VPC-3 (64 KB)
  26  * 0xFFC0_0000 - 0xFFFF_FFFF    NOR Boot FLASH (64 MB)
  27  */
  28
  29 /*
  30  * High Level Configuration Options
  31  */
  32 #define CONFIG_E300             1       /* E300 Family */
  33
  34 #define CONFIG_SYS_TEXT_BASE    0xFFF00000
  35
  36 #define CONFIG_SYS_MPC512X_CLKIN        33333333        /* in Hz */
  37
  38 #define CONFIG_BOARD_EARLY_INIT_F               /* call board_early_init_f() */
  39 #define CONFIG_MISC_INIT_R
  40
  41 #define CONFIG_SYS_IMMR                 0x80000000
  42 #define CONFIG_SYS_DIU_ADDR             (CONFIG_SYS_IMMR+0x2100)
  43
  44 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  45 #define CONFIG_SYS_MEMTEST_END          0x00400000
  46
  47 /*
  48  * DDR Setup - manually set all parameters as there's no SPD etc.
  49  */
  50 #define CONFIG_SYS_DDR_SIZE             512             /* MB */
  51
  52 #define CONFIG_SYS_DDR_BASE             0x00000000      /* DDR is sys memory*/
  53 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  54 #define CONFIG_SYS_MAX_RAM_SIZE         0x20000000
  55
  56 #define CONFIG_SYS_IOCTRL_MUX_DDR       0x00000036
  57
  58 /* DDR Controller Configuration
  59  *
  60  * SYS_CFG:
  61  *      [31:31] MDDRC Soft Reset:       Diabled
  62  *      [30:30] DRAM CKE pin:           Enabled
  63  *      [29:29] DRAM CLK:               Enabled
  64  *      [28:28] Command Mode:           Enabled (For initialization only)
  65  *      [27:25] DRAM Row Select:        dram_row[15:0] = magenta_address[25:10]
  66  *      [24:21] DRAM Bank Select:       dram_bank[1:0] = magenta_address[11:10]
  67  *      [20:19] Read Test:              DON'T USE
  68  *      [18:18] Self Refresh:           Enabled
  69  *      [17:17] 16bit Mode:             Disabled
  70  *      [16:13] Ready Delay:            2
  71  *      [12:12] Half DQS Delay:         Disabled
  72  *      [11:11] Quarter DQS Delay:      Disabled
  73  *      [10:08] Write Delay:            2
  74  *      [07:07] Early ODT:              Disabled
  75  *      [06:06] On DIE Termination:     Disabled
  76  *      [05:05] FIFO Overflow Clear:    DON'T USE here
  77  *      [04:04] FIFO Underflow Clear:   DON'T USE here
  78  *      [03:03] FIFO Overflow Pending:  DON'T USE here
  79  *      [02:02] FIFO Underlfow Pending: DON'T USE here
  80  *      [01:01] FIFO Overlfow Enabled:  Enabled
  81  *      [00:00] FIFO Underflow Enabled: Enabled
  82  * TIME_CFG0
  83  *      [31:16] DRAM Refresh Time:      0 CSB clocks
  84  *      [15:8]  DRAM Command Time:      0 CSB clocks
  85  *      [07:00] DRAM Precharge Time:    0 CSB clocks
  86  * TIME_CFG1
  87  *      [31:26] DRAM tRFC:
  88  *      [25:21] DRAM tWR1:
  89  *      [20:17] DRAM tWRT1:
  90  *      [16:11] DRAM tDRR:
  91  *      [10:05] DRAM tRC:
  92  *      [04:00] DRAM tRAS:
  93  * TIME_CFG2
  94  *      [31:28] DRAM tRCD:
  95  *      [27:23] DRAM tFAW:
  96  *      [22:19] DRAM tRTW1:
  97  *      [18:15] DRAM tCCD:
  98  *      [14:10] DRAM tRTP:
  99  *      [09:05] DRAM tRP:
 100  *      [04:00] DRAM tRPA
 101  */
 102 #define CONFIG_SYS_MDDRC_SYS_CFG         0xEA804A00
 103 #define CONFIG_SYS_MDDRC_TIME_CFG0       0x06183D2E
 104 #define CONFIG_SYS_MDDRC_TIME_CFG1       0x68EC1168
 105 #define CONFIG_SYS_MDDRC_TIME_CFG2       0x34310864
 106
 107 #define CONFIG_SYS_DDRCMD_NOP           0x01380000
 108 #define CONFIG_SYS_DDRCMD_PCHG_ALL      0x01100400
 109 #define CONFIG_SYS_DDRCMD_EM2           0x01020000
 110 #define CONFIG_SYS_DDRCMD_EM3           0x01030000
 111 #define CONFIG_SYS_DDRCMD_EN_DLL        0x01010000
 112 #define CONFIG_SYS_DDRCMD_RFSH          0x01080000
 113 #define CONFIG_SYS_MICRON_INIT_DEV_OP   0x01000432
 114 #define CONFIG_SYS_DDRCMD_OCD_DEFAULT   0x01010780
 115
 116 /* DDR Priority Manager Configuration */
 117 #define CONFIG_SYS_MDDRCGRP_PM_CFG1     0x00077777
 118 #define CONFIG_SYS_MDDRCGRP_PM_CFG2     0x00000000
 119 #define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG  0x00000001
 120 #define CONFIG_SYS_MDDRCGRP_LUT0_MU     0xFFEEDDCC
 121 #define CONFIG_SYS_MDDRCGRP_LUT0_ML     0xBBAAAAAA
 122 #define CONFIG_SYS_MDDRCGRP_LUT1_MU     0x66666666
 123 #define CONFIG_SYS_MDDRCGRP_LUT1_ML     0x55555555
 124 #define CONFIG_SYS_MDDRCGRP_LUT2_MU     0x44444444
 125 #define CONFIG_SYS_MDDRCGRP_LUT2_ML     0x44444444
 126 #define CONFIG_SYS_MDDRCGRP_LUT3_MU     0x55555555
 127 #define CONFIG_SYS_MDDRCGRP_LUT3_ML     0x55555558
 128 #define CONFIG_SYS_MDDRCGRP_LUT4_MU     0x11111111
 129 #define CONFIG_SYS_MDDRCGRP_LUT4_ML     0x11111122
 130 #define CONFIG_SYS_MDDRCGRP_LUT0_AU     0xaaaaaaaa
 131 #define CONFIG_SYS_MDDRCGRP_LUT0_AL     0xaaaaaaaa
 132 #define CONFIG_SYS_MDDRCGRP_LUT1_AU     0x66666666
 133 #define CONFIG_SYS_MDDRCGRP_LUT1_AL     0x66666666
 134 #define CONFIG_SYS_MDDRCGRP_LUT2_AU     0x11111111
 135 #define CONFIG_SYS_MDDRCGRP_LUT2_AL     0x11111111
 136 #define CONFIG_SYS_MDDRCGRP_LUT3_AU     0x11111111
 137 #define CONFIG_SYS_MDDRCGRP_LUT3_AL     0x11111111
 138 #define CONFIG_SYS_MDDRCGRP_LUT4_AU     0x11111111
 139 #define CONFIG_SYS_MDDRCGRP_LUT4_AL     0x11111111
 140
 141 /*
 142  * NOR FLASH on the Local Bus
 143  */
 144 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 145 #define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
 146
 147 #define CONFIG_SYS_FLASH_BASE           0xFFC00000      /* start of FLASH */
 148 #define CONFIG_SYS_FLASH_SIZE           0x00400000      /* max flash size */
 149
 150 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 151 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 152 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
 153 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max sectors per device */
 154
 155 #undef CONFIG_SYS_FLASH_CHECKSUM
 156
 157 /*
 158  * NAND FLASH
 159  * drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only)
 160  */
 161 #define CONFIG_CMD_NAND
 162 #define CONFIG_NAND_MPC5121_NFC
 163 #define CONFIG_SYS_NAND_BASE            0x40000000
 164 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 165
 166 /*
 167  * Configuration parameters for MPC5121 NAND driver
 168  */
 169 #define CONFIG_FSL_NFC_WIDTH            1
 170 #define CONFIG_FSL_NFC_WRITE_SIZE       2048
 171 #define CONFIG_FSL_NFC_SPARE_SIZE       64
 172 #define CONFIG_FSL_NFC_CHIPS            1
 173
 174 #define CONFIG_SYS_SRAM_BASE            0x30000000
 175 #define CONFIG_SYS_SRAM_SIZE            0x00020000      /* 128 KB */
 176
 177 /* Initialize Local Window for NOR FLASH access */
 178 #define CONFIG_SYS_CS0_START            CONFIG_SYS_FLASH_BASE
 179 #define CONFIG_SYS_CS0_SIZE             CONFIG_SYS_FLASH_SIZE
 180
 181 /* ALE active low, data size 4bytes */
 182 #define CONFIG_SYS_CS0_CFG              0x05051150
 183
 184 /* Use not alternative CS timing */
 185 #define CONFIG_SYS_CS_ALETIMING         0x00000000
 186
 187 /* ALE active low, data size 4bytes */
 188 #define CONFIG_SYS_CS1_CFG              0x1f1f3090
 189 #define CONFIG_SYS_VPC3_BASE            0x82000000      /* start of VPC3 space */
 190 #define CONFIG_SYS_VPC3_SIZE            0x00010000      /* max VPC3 size */
 191 /* Initialize Local Window for VPC3 access */
 192 #define CONFIG_SYS_CS1_START            CONFIG_SYS_VPC3_BASE
 193 #define CONFIG_SYS_CS1_SIZE             CONFIG_SYS_VPC3_SIZE
 194
 195 /* Use SRAM for initial stack */
 196 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_SRAM_BASE /* Init RAM addr */
 197 #define CONFIG_SYS_INIT_RAM_SIZE                CONFIG_SYS_SRAM_SIZE
 198
 199 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 200 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 201
 202 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE    /* Start of monitor */
 203 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Monitor length */
 204 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024) /* Malloc size */
 205
 206 /*
 207  * Serial Port
 208  */
 209 #define CONFIG_CONS_INDEX     1
 210
 211 /*
 212  * Serial console configuration
 213  */
 214 #define CONFIG_PSC_CONSOLE      3       /* console is on PSC3 */
 215 #define CONFIG_SYS_PSC3
 216 #if CONFIG_PSC_CONSOLE != 3
 217 #error CONFIG_PSC_CONSOLE must be 3
 218 #endif
 219 #define CONFIG_BAUDRATE         9600    /* ... at 9600 bps */
 220 #define CONFIG_SYS_BAUDRATE_TABLE  \
 221         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 222
 223 #define CONSOLE_FIFO_TX_SIZE    FIFOC_PSC3_TX_SIZE
 224 #define CONSOLE_FIFO_TX_ADDR    FIFOC_PSC3_TX_ADDR
 225 #define CONSOLE_FIFO_RX_SIZE    FIFOC_PSC3_RX_SIZE
 226 #define CONSOLE_FIFO_RX_ADDR    FIFOC_PSC3_RX_ADDR
 227
 228 /*
 229  * Clocks in use
 230  */
 231 #define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN |                           \
 232                          CLOCK_SCCR1_LPC_EN |                           \
 233                          CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) |       \
 234                          CLOCK_SCCR1_PSCFIFO_EN |                       \
 235                          CLOCK_SCCR1_DDR_EN |                           \
 236                          CLOCK_SCCR1_FEC_EN |                           \
 237                          CLOCK_SCCR1_NFC_EN |                           \
 238                          CLOCK_SCCR1_PCI_EN |                           \
 239                          CLOCK_SCCR1_TPR_EN)
 240
 241 #define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN |   \
 242                          CLOCK_SCCR2_I2C_EN)
 243
 244 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 245
 246 /* I2C */
 247 #define CONFIG_HARD_I2C                 /* I2C with hardware support */
 248 #define CONFIG_I2C_MULTI_BUS
 249 #define CONFIG_SYS_I2C_SPEED            400000  /* I2C speed */
 250 #define CONFIG_SYS_I2C_SLAVE            0x7F    /* slave address */
 251
 252 /*
 253  * IIM - IC Identification Module
 254  */
 255 #undef CONFIG_FSL_IIM
 256
 257 /*
 258  * EEPROM configuration
 259  */
 260 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2       /* 16-bit EEPROM address */
 261 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* Atmel: AT24C32A-10TQ-2.7 */
 262 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10        /* 10ms of delay */
 263 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5     /* 32-Byte Page Write Mode */
 264 #define CONFIG_SYS_EEPROM_WREN                  /* Use EEPROM write protect */
 265
 266 /*
 267  * Ethernet configuration
 268  */
 269 #define CONFIG_MPC512x_FEC      1
 270 #define CONFIG_PHY_ADDR         0x1
 271 #define CONFIG_MII              1       /* MII PHY management           */
 272 #define CONFIG_FEC_AN_TIMEOUT   1
 273 #define CONFIG_HAS_ETH0
 274
 275 /*
 276  * Configure on-board RTC
 277  */
 278 #define CONFIG_SYS_RTC_BUS_NUM  0x01
 279 #define CONFIG_SYS_I2C_RTC_ADDR 0x32
 280 #define CONFIG_RTC_RX8025
 281
 282 /*
 283  * Environment
 284  */
 285 #define CONFIG_ENV_IS_IN_EEPROM         /* Store env in I2C EEPROM      */
 286 #define CONFIG_ENV_SIZE         0x1000
 287 #define CONFIG_ENV_OFFSET       0x0000  /* environment starts here      */
 288
 289 #define CONFIG_LOADS_ECHO               /* echo on for serial download  */
 290 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change        */
 291
 292 #define CONFIG_CMD_REGINFO
 293 #define CONFIG_CMD_EEPROM
 294 #define CONFIG_CMD_DATE
 295 #undef CONFIG_CMD_FUSE
 296 #undef CONFIG_CMD_IDE
 297 #define CONFIG_CMD_JFFS2
 298 #define CONFIG_DOS_PARTITION
 299
 300 /*
 301  * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
 302  * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
 303  * to 0xFFFF, watchdog timeouts after about 64s. For details refer
 304  * to chapter 36 of the MPC5121e Reference Manual.
 305  */
 306 /* #define CONFIG_WATCHDOG */           /* enable watchdog */
 307 #define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF
 308
 309  /*
 310  * Miscellaneous configurable options
 311  */
 312 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 313 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 314
 315 #ifdef CONFIG_CMD_KGDB
 316 # define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
 317 #else
 318 # define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
 319 #endif
 320
 321 /* Print Buffer Size */
 322 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE + \
 323                                  sizeof(CONFIG_SYS_PROMPT) + 16)
 324 /* max number of command args */
 325 #define CONFIG_SYS_MAXARGS      32
 326 /* Boot Argument Buffer Size */
 327 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 328
 329 /*
 330  * For booting Linux, the board info and command line data
 331  * have to be in the first 256 MB of memory, since this is
 332  * the maximum mapped by the Linux kernel during initialization.
 333  */
 334 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Linux initial memory map */
 335
 336 /* Cache Configuration */
 337 #define CONFIG_SYS_DCACHE_SIZE          32768
 338 #define CONFIG_SYS_CACHELINE_SIZE       32
 339 #ifdef CONFIG_CMD_KGDB
 340 #define CONFIG_SYS_CACHELINE_SHIFT      5
 341 #endif
 342
 343 #define CONFIG_SYS_HID0_INIT    0x000000000
 344 #define CONFIG_SYS_HID0_FINAL   HID0_ENABLE_MACHINE_CHECK
 345 #define CONFIG_SYS_HID2         HID2_HBE
 346
 347 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 348
 349 #ifdef CONFIG_CMD_KGDB
 350 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 351 #endif
 352
 353 /*
 354  * Environment Configuration
 355  */
 356 #define CONFIG_TIMESTAMP
 357
 358 #define CONFIG_HOSTNAME         mecp512x
 359 #define CONFIG_BOOTFILE         "/tftpboot/mecp512x/uImage"
 360 #define CONFIG_ROOTPATH         "/tftpboot/mecp512x/target_root"
 361
 362 #define CONFIG_LOADADDR         400000  /* def. location for tftp and bootm */
 363
 364 #undef  CONFIG_BOOTARGS                 /* the boot command will set bootargs*/
 365
 366 #define CONFIG_PREBOOT  "echo;" \
 367         "echo Welcome to MECP5123" \
 368         "echo"
 369
 370 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 371         "u-boot_addr_r=200000\0"                                        \
 372         "kernel_addr_r=600000\0"                                        \
 373         "fdt_addr_r=880000\0"                                           \
 374         "ramdisk_addr_r=900000\0"                                       \
 375         "u-boot_addr=FFF00000\0"                                        \
 376         "kernel_addr=FFC40000\0"                                        \
 377         "fdt_addr=FFEC0000\0"                                           \
 378         "ramdisk_addr=FC040000\0"                                       \
 379         "ramdiskfile=/tftpboot/mecp512x/uRamdisk\0"                     \
 380         "u-boot=/tftpboot/mecp512x/u-boot.bin\0"                        \
 381         "bootfile=/tftpboot/mecp512x/uImage\0"                          \
 382         "fdtfile=/tftpboot/mecp512x/mecp512x.dtb\0"                     \
 383         "rootpath=/tftpboot/mecp512x/target_root\n"                     \
 384         "netdev=eth0\0"                                                 \
 385         "consdev=ttyPSC0\0"                                             \
 386         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 387                 "nfsroot=${serverip}:${rootpath}\0"                     \
 388         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 389         "addip=setenv bootargs ${bootargs} "                            \
 390                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 391                 ":${hostname}:${netdev}:off panic=1\0"                  \
 392         "addtty=setenv bootargs ${bootargs} "                           \
 393                 "console=${consdev},${baudrate}\0"                      \
 394         "flash_nfs=run nfsargs addip addtty;"                           \
 395                 "bootm ${kernel_addr} - ${fdt_addr}\0"                  \
 396         "flash_self=run ramargs addip addtty;"                          \
 397                 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"    \
 398         "net_nfs=tftp ${kernel_addr_r} ${bootfile};"                    \
 399                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 400                 "run nfsargs addip addtty;"                             \
 401                 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0"              \
 402         "net_self=tftp ${kernel_addr_r} ${bootfile};"                   \
 403                 "tftp ${ramdisk_addr_r} ${ramdiskfile};"                \
 404                 "tftp ${fdt_addr_r} ${fdtfile};"                        \
 405                 "run ramargs addip addtty;"                             \
 406                 "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\
 407         "load=tftp ${u-boot_addr_r} ${u-boot}\0"                        \
 408         "update=protect off ${u-boot_addr} +${filesize};"               \
 409                 "era ${u-boot_addr} +${filesize};"                      \
 410                 "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0"    \
 411         "upd=run load update\0"                                         \
 412         ""
 413
 414 #define CONFIG_BOOTCOMMAND      "run flash_self"
 415
 416 #define OF_CPU                  "PowerPC,5121@0"
 417 #define OF_SOC_COMPAT           "fsl,mpc5121-immr"
 418 #define OF_TBCLK                (bd->bi_busfreq / 4)
 419 #define OF_STDOUT_PATH          "/soc@80000000/serial@11300"
 420
 421 #endif  /* __CONFIG_H */