include/configs/mx28evk.h

   1 /*
   2  * (C) Copyright 2011 Freescale Semiconductor, Inc.
   3  * Author: Fabio Estevam <fabio.estevam@freescale.com>
   4  *
   5  * Based on m28evk.h:
   6  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
   7  * on behalf of DENX Software Engineering GmbH
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11 #ifndef __CONFIGS_MX28EVK_H__
  12 #define __CONFIGS_MX28EVK_H__
  13
  14 /* System configurations */
  15 #define CONFIG_MX28                             /* i.MX28 SoC */
  16 #define CONFIG_MACH_TYPE        MACH_TYPE_MX28EVK
  17
  18 /* U-Boot Commands */
  19 #define CONFIG_SYS_NO_FLASH
  20 #include <config_cmd_default.h>
  21 #define CONFIG_DISPLAY_CPUINFO
  22 #define CONFIG_DOS_PARTITION
  23
  24 #define CONFIG_CMD_CACHE
  25 #define CONFIG_CMD_DATE
  26 #define CONFIG_CMD_DHCP
  27 #define CONFIG_CMD_FAT
  28 #define CONFIG_CMD_GPIO
  29 #define CONFIG_CMD_MII
  30 #define CONFIG_CMD_MMC
  31 #define CONFIG_CMD_NET
  32 #define CONFIG_CMD_NFS
  33 #define CONFIG_CMD_PING
  34 #define CONFIG_CMD_SAVEENV
  35 #define CONFIG_CMD_SF
  36 #define CONFIG_CMD_SPI
  37 #define CONFIG_CMD_USB
  38 #define CONFIG_CMD_BOOTZ
  39 #define CONFIG_CMD_NAND
  40 #define CONFIG_CMD_NAND_TRIMFFS
  41 #define CONFIG_VIDEO
  42
  43 /* Memory configuration */
  44 #define CONFIG_NR_DRAM_BANKS            1               /* 1 bank of DRAM */
  45 #define PHYS_SDRAM_1                    0x40000000      /* Base address */
  46 #define PHYS_SDRAM_1_SIZE               0x40000000      /* Max 1 GB RAM */
  47 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
  48
  49 /* Environment */
  50 #ifndef CONFIG_ENV_IS_IN_SPI_FLASH
  51 #define CONFIG_ENV_SIZE                 (16 * 1024)
  52 #else
  53 #define CONFIG_ENV_SIZE                 (4 * 1024)
  54 #endif
  55 #define CONFIG_ENV_OVERWRITE
  56
  57 /* Environment is in MMC */
  58 #if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC)
  59 #define CONFIG_ENV_OFFSET               (256 * 1024)
  60 #define CONFIG_SYS_MMC_ENV_DEV          0
  61 #endif
  62
  63 /* Environment is in NAND */
  64 #if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
  65 #define CONFIG_ENV_SIZE_REDUND          CONFIG_ENV_SIZE
  66 #define CONFIG_ENV_SECT_SIZE            (128 * 1024)
  67 #define CONFIG_ENV_RANGE                (512 * 1024)
  68 #define CONFIG_ENV_OFFSET               0x300000
  69 #define CONFIG_ENV_OFFSET_REDUND        \
  70                 (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
  71 #endif
  72
  73 /* Environemnt is in SPI flash */
  74 #if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH)
  75 #define CONFIG_SYS_REDUNDAND_ENVIRONMENT
  76 #define CONFIG_ENV_OFFSET               0x40000         /* 256K */
  77 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
  78 #define CONFIG_ENV_SECT_SIZE            0x1000
  79 #define CONFIG_ENV_SPI_CS               0
  80 #define CONFIG_ENV_SPI_BUS              2
  81 #define CONFIG_ENV_SPI_MAX_HZ           24000000
  82 #define CONFIG_ENV_SPI_MODE             SPI_MODE_0
  83 #endif
  84
  85 /* UBI and NAND partitioning */
  86 #ifdef CONFIG_CMD_NAND
  87 #define CONFIG_CMD_UBI
  88 #define CONFIG_CMD_UBIFS
  89 #define CONFIG_CMD_MTDPARTS
  90 #define CONFIG_RBTREE
  91 #define CONFIG_LZO
  92 #define CONFIG_MTD_DEVICE
  93 #define CONFIG_MTD_PARTITIONS
  94 #define MTDIDS_DEFAULT                  "nand0=gpmi-nand"
  95 #define MTDPARTS_DEFAULT                        \
  96         "mtdparts=gpmi-nand:"                   \
  97                 "3m(bootloader)ro,"             \
  98                 "512k(environment),"            \
  99                 "512k(redundant-environment),"  \
 100                 "4m(kernel),"                   \
 101                 "512k(fdt),"                    \
 102                 "8m(ramdisk),"                  \
 103                 "-(filesystem)"
 104 #endif
 105
 106 /* FEC Ethernet on SoC */
 107 #ifdef  CONFIG_CMD_NET
 108 #define CONFIG_FEC_MXC
 109 #define CONFIG_NET_MULTI
 110 #define CONFIG_MX28_FEC_MAC_IN_OCOTP
 111 #endif
 112
 113 /* RTC */
 114 #ifdef  CONFIG_CMD_DATE
 115 #define CONFIG_RTC_MXS
 116 #endif
 117
 118 /* USB */
 119 #ifdef  CONFIG_CMD_USB
 120 #define CONFIG_EHCI_MXS_PORT1
 121 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1
 122 #define CONFIG_USB_STORAGE
 123 #define CONFIG_USB_HOST_ETHER
 124 #define CONFIG_USB_ETHER_ASIX
 125 #define CONFIG_USB_ETHER_SMSC95XX
 126 #endif
 127
 128 /* SPI */
 129 #ifdef CONFIG_CMD_SPI
 130 #define CONFIG_DEFAULT_SPI_BUS          2
 131 #define CONFIG_DEFAULT_SPI_MODE         SPI_MODE_0
 132
 133 /* SPI Flash */
 134 #ifdef CONFIG_CMD_SF
 135 #define CONFIG_SPI_FLASH
 136 #define CONFIG_SF_DEFAULT_BUS           2
 137 #define CONFIG_SF_DEFAULT_CS            0
 138 /* this may vary and depends on the installed chip */
 139 #define CONFIG_SPI_FLASH_SST
 140 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
 141 #define CONFIG_SF_DEFAULT_SPEED         24000000
 142 #endif
 143
 144 #endif
 145
 146 /* Framebuffer support */
 147 #ifdef CONFIG_VIDEO
 148 #define CONFIG_VIDEO_LOGO
 149 #define CONFIG_SPLASH_SCREEN
 150 #define CONFIG_CMD_BMP
 151 #define CONFIG_BMP_16BPP
 152 #define CONFIG_VIDEO_BMP_RLE8
 153 #define CONFIG_VIDEO_BMP_GZIP
 154 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE  (512 << 10)
 155 #endif
 156
 157 /* Boot Linux */
 158 #define CONFIG_BOOTDELAY        1
 159 #define CONFIG_BOOTFILE         "uImage"
 160 #define CONFIG_LOADADDR         0x42000000
 161 #define CONFIG_SYS_LOAD_ADDR    CONFIG_LOADADDR
 162
 163 /* Extra Environment */
 164 #define CONFIG_EXTRA_ENV_SETTINGS \
 165         "ubifs_file=filesystem.ubifs\0" \
 166         "update_nand_full_filename=u-boot.nand\0" \
 167         "update_nand_firmware_filename=u-boot.sb\0"     \
 168         "update_nand_firmware_maxsz=0x100000\0" \
 169         "update_nand_stride=0x40\0"     /* MX28 datasheet ch. 12.12 */ \
 170         "update_nand_count=0x4\0"       /* MX28 datasheet ch. 12.12 */ \
 171         "update_nand_get_fcb_size="     /* Get size of FCB blocks */ \
 172                 "nand device 0 ; " \
 173                 "nand info ; " \
 174                 "setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
 175                 "setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
 176         "update_nand_firmware_full=" /* Update FCB, DBBT and FW */ \
 177                 "if tftp ${update_nand_full_filename} ; then " \
 178                 "run update_nand_get_fcb_size ; " \
 179                 "nand scrub -y 0x0 ${filesize} ; " \
 180                 "nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; " \
 181                 "setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
 182                 "setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
 183                 "nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
 184                 "fi\0" \
 185         "update_nand_firmware="         /* Update only firmware */ \
 186                 "if tftp ${update_nand_firmware_filename} ; then " \
 187                 "run update_nand_get_fcb_size ; " \
 188                 "setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
 189                 "setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; " \
 190                 "setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
 191                 "nand erase ${fcb_sz} ${fw_sz} ; " \
 192                 "nand write ${loadaddr} ${fcb_sz} ${filesize} ; " \
 193                 "nand write ${loadaddr} ${fw_off} ${filesize} ; " \
 194                 "fi\0" \
 195         "update_nand_kernel="           /* Update kernel */ \
 196                 "mtdparts default; " \
 197                 "nand erase.part kernel; " \
 198                 "if test ${ip_dyn} = yes; then " \
 199                         "setenv get_cmd dhcp; " \
 200                 "else " \
 201                         "setenv get_cmd tftp; " \
 202                 "fi; " \
 203                 "${get_cmd} ${image}; " \
 204                 "nand write ${loadaddr} kernel ${filesize}\0" \
 205         "update_nand_fdt="              /* Update fdt */ \
 206                 "mtdparts default; " \
 207                 "nand erase.part fdt; " \
 208                 "if test ${ip_dyn} = yes; then " \
 209                         "setenv get_cmd dhcp; " \
 210                 "else " \
 211                         "setenv get_cmd tftp; " \
 212                 "fi; " \
 213                 "${get_cmd} ${fdt_file}; " \
 214                 "nand write ${loadaddr} fdt ${filesize}\0" \
 215         "update_nand_filesystem="               /* Update filesystem */ \
 216                 "mtdparts default; " \
 217                 "nand erase.part filesystem; " \
 218                 "if test ${ip_dyn} = yes; then " \
 219                         "setenv get_cmd dhcp; " \
 220                 "else " \
 221                         "setenv get_cmd tftp; " \
 222                 "fi; " \
 223                 "${get_cmd} ${ubifs_file}; " \
 224                 "ubi part filesystem; " \
 225                 "ubi create filesystem; " \
 226                 "ubi write ${loadaddr} filesystem ${filesize}\0" \
 227         "nandargs=setenv bootargs console=${console_mainline},${baudrate} " \
 228                 "rootfstype=ubifs ubi.mtd=6 root=ubi0_0 ${mtdparts}\0" \
 229         "nandboot="             /* Boot from NAND */ \
 230                 "mtdparts default; " \
 231                 "run nandargs; " \
 232                 "nand read ${loadaddr} kernel 0x00400000; " \
 233                 "if test ${boot_fdt} = yes; then " \
 234                         "nand read ${fdt_addr} fdt 0x00080000; " \
 235                         "bootz ${loadaddr} - ${fdt_addr}; " \
 236                 "else " \
 237                         "if test ${boot_fdt} = no; then " \
 238                                 "bootz; " \
 239                         "else " \
 240                                 "echo \"ERROR: Set boot_fdt to yes or no.\"; " \
 241                         "fi; " \
 242                 "fi\0" \
 243         "update_sd_firmware_filename=u-boot.sd\0" \
 244         "update_sd_firmware="           /* Update the SD firmware partition */ \
 245                 "if mmc rescan ; then " \
 246                 "if tftp ${update_sd_firmware_filename} ; then " \
 247                 "setexpr fw_sz ${filesize} / 0x200 ; "  /* SD block size */ \
 248                 "setexpr fw_sz ${fw_sz} + 1 ; " \
 249                 "mmc write ${loadaddr} 0x800 ${fw_sz} ; " \
 250                 "fi ; " \
 251                 "fi\0" \
 252         "script=boot.scr\0"     \
 253         "image=zImage\0" \
 254         "console_fsl=ttyAM0\0" \
 255         "console_mainline=ttyAMA0\0" \
 256         "fdt_file=imx28-evk.dtb\0" \
 257         "fdt_addr=0x41000000\0" \
 258         "boot_fdt=try\0" \
 259         "ip_dyn=yes\0" \
 260         "mmcdev=0\0" \
 261         "mmcpart=2\0" \
 262         "mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
 263         "mmcargs=setenv bootargs console=${console_mainline},${baudrate} " \
 264                 "root=${mmcroot}\0" \
 265         "loadbootscript="  \
 266                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 267         "bootscript=echo Running bootscript from mmc ...; "     \
 268                 "source\0" \
 269         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 270         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 271         "mmcboot=echo Booting from mmc ...; " \
 272                 "run mmcargs; " \
 273                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 274                         "if run loadfdt; then " \
 275                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 276                         "else " \
 277                                 "if test ${boot_fdt} = try; then " \
 278                                         "bootz; " \
 279                                 "else " \
 280                                         "echo WARN: Cannot load the DT; " \
 281                                 "fi; " \
 282                         "fi; " \
 283                 "else " \
 284                         "bootz; " \
 285                 "fi;\0" \
 286         "netargs=setenv bootargs console=${console_mainline},${baudrate} " \
 287                 "root=/dev/nfs " \
 288                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 289         "netboot=echo Booting from net ...; " \
 290                 "run netargs; " \
 291                 "if test ${ip_dyn} = yes; then " \
 292                         "setenv get_cmd dhcp; " \
 293                 "else " \
 294                         "setenv get_cmd tftp; " \
 295                 "fi; " \
 296                 "${get_cmd} ${image}; " \
 297                 "if test ${boot_fdt} = yes; then " \
 298                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 299                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 300                         "else " \
 301                                 "if test ${boot_fdt} = try; then " \
 302                                         "bootz; " \
 303                                 "else " \
 304                                         "echo WARN: Cannot load the DT; " \
 305                                 "fi;" \
 306                         "fi; " \
 307                 "else " \
 308                         "bootz; " \
 309                 "fi;\0"
 310
 311 #define CONFIG_BOOTCOMMAND \
 312         "mmc dev ${mmcdev}; if mmc rescan; then " \
 313                 "if run loadbootscript; then " \
 314                         "run bootscript; " \
 315                 "else " \
 316                         "if run loadimage; then " \
 317                                 "run mmcboot; " \
 318                         "else run netboot; " \
 319                         "fi; " \
 320                 "fi; " \
 321         "else run netboot; fi"
 322
 323 /* The rest of the configuration is shared */
 324 #include <configs/mxs.h>
 325
 326 #endif /* __CONFIGS_MX28EVK_H__ */