include/configs/mx53loco.h

   1 /*
   2  * Copyright (C) 2011 Freescale Semiconductor, Inc.
   3  * Jason Liu <r64343@freescale.com>
   4  *
   5  * Configuration settings for Freescale MX53 low cost board.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_MX53
  14
  15 #define CONFIG_DISPLAY_BOARDINFO
  16
  17 #define CONFIG_MACH_TYPE        MACH_TYPE_MX53_LOCO
  18
  19 #include <asm/arch/imx-regs.h>
  20
  21 #define CONFIG_CMDLINE_TAG
  22 #define CONFIG_SETUP_MEMORY_TAGS
  23 #define CONFIG_INITRD_TAG
  24
  25 #define CONFIG_SYS_FSL_CLK
  26
  27 /* Size of malloc() pool */
  28 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  29
  30 #define CONFIG_BOARD_EARLY_INIT_F
  31 #define CONFIG_BOARD_LATE_INIT
  32 #define CONFIG_MXC_GPIO
  33 #define CONFIG_REVISION_TAG
  34
  35 #define CONFIG_MXC_UART
  36 #define CONFIG_MXC_UART_BASE    UART1_BASE
  37
  38 /* MMC Configs */
  39 #define CONFIG_FSL_ESDHC
  40 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  41 #define CONFIG_SYS_FSL_ESDHC_NUM        2
  42
  43 #define CONFIG_MMC
  44 #define CONFIG_GENERIC_MMC
  45 #define CONFIG_DOS_PARTITION
  46
  47 /* Eth Configs */
  48 #define CONFIG_MII
  49
  50 #define CONFIG_FEC_MXC
  51 #define IMX_FEC_BASE    FEC_BASE_ADDR
  52 #define CONFIG_FEC_MXC_PHYADDR  0x1F
  53
  54 /* USB Configs */
  55 #define CONFIG_USB_EHCI
  56 #define CONFIG_USB_EHCI_MX5
  57 #define CONFIG_USB_STORAGE
  58 #define CONFIG_USB_HOST_ETHER
  59 #define CONFIG_USB_ETHER_ASIX
  60 #define CONFIG_USB_ETHER_MCS7830
  61 #define CONFIG_USB_ETHER_SMSC95XX
  62 #define CONFIG_MXC_USB_PORT     1
  63 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  64 #define CONFIG_MXC_USB_FLAGS    0
  65
  66 /* I2C Configs */
  67 #define CONFIG_SYS_I2C
  68 #define CONFIG_SYS_I2C_MXC
  69 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  70 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  71 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  72
  73 /* PMIC Controller */
  74 #define CONFIG_POWER
  75 #define CONFIG_POWER_I2C
  76 #define CONFIG_DIALOG_POWER
  77 #define CONFIG_POWER_FSL
  78 #define CONFIG_POWER_FSL_MC13892
  79 #define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
  80 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x8
  81
  82 /* allow to overwrite serial and ethaddr */
  83 #define CONFIG_ENV_OVERWRITE
  84 #define CONFIG_CONS_INDEX               1
  85 #define CONFIG_BAUDRATE                 115200
  86
  87 /* Command definition */
  88 #define CONFIG_SUPPORT_RAW_INITRD
  89
  90
  91 #define CONFIG_ETHPRIME         "FEC0"
  92
  93 #define CONFIG_LOADADDR         0x72000000      /* loadaddr env var */
  94 #define CONFIG_SYS_TEXT_BASE    0x77800000
  95
  96 #define CONFIG_EXTRA_ENV_SETTINGS \
  97         "script=boot.scr\0" \
  98         "image=zImage\0" \
  99         "fdt_addr=0x71000000\0" \
 100         "boot_fdt=try\0" \
 101         "ip_dyn=yes\0" \
 102         "mmcdev=0\0" \
 103         "mmcpart=1\0" \
 104         "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
 105         "mmcargs=setenv bootargs console=ttymxc0,${baudrate} root=${mmcroot}\0" \
 106         "loadbootscript=" \
 107                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 108         "bootscript=echo Running bootscript from mmc ...; " \
 109                 "source\0" \
 110         "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 111         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 112         "mmcboot=echo Booting from mmc ...; " \
 113                 "run mmcargs; " \
 114                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 115                         "if run loadfdt; then " \
 116                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 117                         "else " \
 118                                 "if test ${boot_fdt} = try; then " \
 119                                         "bootz; " \
 120                                 "else " \
 121                                         "echo WARN: Cannot load the DT; " \
 122                                 "fi; " \
 123                         "fi; " \
 124                 "else " \
 125                         "bootz; " \
 126                 "fi;\0" \
 127         "netargs=setenv bootargs console=ttymxc0,${baudrate} " \
 128                 "root=/dev/nfs " \
 129                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 130         "netboot=echo Booting from net ...; " \
 131                 "run netargs; " \
 132                 "if test ${ip_dyn} = yes; then " \
 133                         "setenv get_cmd dhcp; " \
 134                 "else " \
 135                         "setenv get_cmd tftp; " \
 136                 "fi; " \
 137                 "${get_cmd} ${image}; " \
 138                 "if test ${boot_fdt} = yes ||  test ${boot_fdt} = try; then " \
 139                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 140                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 141                         "else " \
 142                                 "if test ${boot_fdt} = try; then " \
 143                                         "bootz; " \
 144                                 "else " \
 145                                         "echo ERROR: Cannot load the DT; " \
 146                                         "exit; " \
 147                                 "fi; " \
 148                         "fi; " \
 149                 "else " \
 150                         "bootz; " \
 151                 "fi;\0"
 152
 153 #define CONFIG_BOOTCOMMAND \
 154         "mmc dev ${mmcdev}; if mmc rescan; then " \
 155                 "if run loadbootscript; then " \
 156                         "run bootscript; " \
 157                 "else " \
 158                         "if run loadimage; then " \
 159                                 "run mmcboot; " \
 160                         "else run netboot; " \
 161                         "fi; " \
 162                 "fi; " \
 163         "else run netboot; fi"
 164
 165 #define CONFIG_ARP_TIMEOUT      200UL
 166
 167 /* Miscellaneous configurable options */
 168 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 169 #define CONFIG_AUTO_COMPLETE
 170 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 171
 172 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 173 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 174
 175 #define CONFIG_SYS_MEMTEST_START       0x70000000
 176 #define CONFIG_SYS_MEMTEST_END         0x70010000
 177
 178 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 179
 180 #define CONFIG_CMDLINE_EDITING
 181
 182 /* Physical Memory Map */
 183 #define CONFIG_NR_DRAM_BANKS    2
 184 #define PHYS_SDRAM_1                    CSD0_BASE_ADDR
 185 #define PHYS_SDRAM_1_SIZE               (gd->bd->bi_dram[0].size)
 186 #define PHYS_SDRAM_2                    CSD1_BASE_ADDR
 187 #define PHYS_SDRAM_2_SIZE               (gd->bd->bi_dram[1].size)
 188 #define PHYS_SDRAM_SIZE                 (gd->ram_size)
 189
 190 #define CONFIG_SYS_SDRAM_BASE           (PHYS_SDRAM_1)
 191 #define CONFIG_SYS_INIT_RAM_ADDR        (IRAM_BASE_ADDR)
 192 #define CONFIG_SYS_INIT_RAM_SIZE        (IRAM_SIZE)
 193
 194 #define CONFIG_SYS_INIT_SP_OFFSET \
 195         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 196 #define CONFIG_SYS_INIT_SP_ADDR \
 197         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 198
 199 /* FLASH and environment organization */
 200 #define CONFIG_SYS_NO_FLASH
 201
 202 #define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
 203 #define CONFIG_ENV_SIZE        (8 * 1024)
 204 #define CONFIG_ENV_IS_IN_MMC
 205 #define CONFIG_SYS_MMC_ENV_DEV 0
 206
 207 #define CONFIG_CMD_SATA
 208 #ifdef CONFIG_CMD_SATA
 209         #define CONFIG_DWC_AHSATA
 210         #define CONFIG_SYS_SATA_MAX_DEVICE      1
 211         #define CONFIG_DWC_AHSATA_PORT_ID       0
 212         #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_BASE_ADDR
 213         #define CONFIG_LBA48
 214         #define CONFIG_LIBATA
 215 #endif
 216
 217 /* Framebuffer and LCD */
 218 #define CONFIG_PREBOOT
 219 #define CONFIG_VIDEO
 220 #define CONFIG_VIDEO_IPUV3
 221 #define CONFIG_CFB_CONSOLE
 222 #define CONFIG_VGA_AS_SINGLE_DEVICE
 223 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 224 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 225 #define CONFIG_VIDEO_BMP_RLE8
 226 #define CONFIG_SPLASH_SCREEN
 227 #define CONFIG_BMP_16BPP
 228 #define CONFIG_VIDEO_LOGO
 229 #define CONFIG_IPUV3_CLK        200000000
 230
 231 #endif                          /* __CONFIG_H */