include/configs/mx53loco.h

   1 /*
   2  * Copyright (C) 2011 Freescale Semiconductor, Inc.
   3  * Jason Liu <r64343@freescale.com>
   4  *
   5  * Configuration settings for Freescale MX53 low cost board.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_MX53
  14
  15 #define CONFIG_DISPLAY_BOARDINFO
  16
  17 #define CONFIG_MACH_TYPE        MACH_TYPE_MX53_LOCO
  18
  19 #include <asm/arch/imx-regs.h>
  20
  21 #define CONFIG_CMDLINE_TAG
  22 #define CONFIG_SETUP_MEMORY_TAGS
  23 #define CONFIG_INITRD_TAG
  24
  25 /* Size of malloc() pool */
  26 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  27
  28 #define CONFIG_BOARD_EARLY_INIT_F
  29 #define CONFIG_BOARD_LATE_INIT
  30 #define CONFIG_MXC_GPIO
  31 #define CONFIG_REVISION_TAG
  32
  33 #define CONFIG_MXC_UART
  34 #define CONFIG_MXC_UART_BASE    UART1_BASE
  35
  36 /* MMC Configs */
  37 #define CONFIG_FSL_ESDHC
  38 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  39 #define CONFIG_SYS_FSL_ESDHC_NUM        2
  40
  41 #define CONFIG_MMC
  42 #define CONFIG_CMD_MMC
  43 #define CONFIG_GENERIC_MMC
  44 #define CONFIG_CMD_FAT
  45 #define CONFIG_CMD_EXT2
  46 #define CONFIG_DOS_PARTITION
  47
  48 /* Eth Configs */
  49 #define CONFIG_MII
  50
  51 #define CONFIG_FEC_MXC
  52 #define IMX_FEC_BASE    FEC_BASE_ADDR
  53 #define CONFIG_FEC_MXC_PHYADDR  0x1F
  54
  55 #define CONFIG_CMD_PING
  56 #define CONFIG_CMD_DHCP
  57 #define CONFIG_CMD_MII
  58 #define CONFIG_CMD_NET
  59
  60 /* USB Configs */
  61 #define CONFIG_CMD_USB
  62 #define CONFIG_CMD_FAT
  63 #define CONFIG_USB_EHCI
  64 #define CONFIG_USB_EHCI_MX5
  65 #define CONFIG_USB_STORAGE
  66 #define CONFIG_USB_HOST_ETHER
  67 #define CONFIG_USB_ETHER_ASIX
  68 #define CONFIG_USB_ETHER_SMSC95XX
  69 #define CONFIG_MXC_USB_PORT     1
  70 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  71 #define CONFIG_MXC_USB_FLAGS    0
  72
  73 /* I2C Configs */
  74 #define CONFIG_HARD_I2C
  75 #define CONFIG_I2C_MXC
  76 #define CONFIG_SYS_I2C_BASE             I2C1_BASE_ADDR
  77 #define CONFIG_SYS_I2C_SPEED            100000
  78
  79 /* PMIC Controller */
  80 #define CONFIG_POWER
  81 #define CONFIG_POWER_I2C
  82 #define CONFIG_DIALOG_POWER
  83 #define CONFIG_POWER_FSL
  84 #define CONFIG_PMIC_FSL_MC13892
  85 #define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48
  86 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x8
  87
  88 /* allow to overwrite serial and ethaddr */
  89 #define CONFIG_ENV_OVERWRITE
  90 #define CONFIG_CONS_INDEX               1
  91 #define CONFIG_BAUDRATE                 115200
  92
  93 /* Command definition */
  94 #include <config_cmd_default.h>
  95 #define CONFIG_CMD_BOOTZ
  96
  97 #undef CONFIG_CMD_IMLS
  98
  99 #define CONFIG_BOOTDELAY        1
 100
 101 #define CONFIG_ETHPRIME         "FEC0"
 102
 103 #define CONFIG_LOADADDR         0x72000000      /* loadaddr env var */
 104 #define CONFIG_SYS_TEXT_BASE    0x77800000
 105
 106 #define CONFIG_EXTRA_ENV_SETTINGS \
 107         "script=boot.scr\0" \
 108         "uimage=uImage\0" \
 109         "fdt_file=imx53-qsb.dtb\0" \
 110         "fdt_addr=0x71000000\0" \
 111         "boot_fdt=try\0" \
 112         "ip_dyn=yes\0" \
 113         "mmcdev=0\0" \
 114         "mmcpart=1\0" \
 115         "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
 116         "mmcargs=setenv bootargs console=ttymxc0,${baudrate} root=${mmcroot}\0" \
 117         "loadbootscript=" \
 118                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 119         "bootscript=echo Running bootscript from mmc ...; " \
 120                 "source\0" \
 121         "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
 122         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 123         "mmcboot=echo Booting from mmc ...; " \
 124                 "run mmcargs; " \
 125                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 126                         "if run loadfdt; then " \
 127                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 128                         "else " \
 129                                 "if test ${boot_fdt} = try; then " \
 130                                         "bootm; " \
 131                                 "else " \
 132                                         "echo WARN: Cannot load the DT; " \
 133                                 "fi; " \
 134                         "fi; " \
 135                 "else " \
 136                         "bootm; " \
 137                 "fi;\0" \
 138         "netargs=setenv bootargs console=ttymxc0,${baudrate} " \
 139                 "root=/dev/nfs " \
 140                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 141         "netboot=echo Booting from net ...; " \
 142                 "run netargs; " \
 143                 "if test ${ip_dyn} = yes; then " \
 144                         "setenv get_cmd dhcp; " \
 145                 "else " \
 146                         "setenv get_cmd tftp; " \
 147                 "fi; " \
 148                 "${get_cmd} ${uimage}; " \
 149                 "if test ${boot_fdt} = yes ||  test ${boot_fdt} = try; then " \
 150                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 151                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 152                         "else " \
 153                                 "if test ${boot_fdt} = try; then " \
 154                                         "bootm; " \
 155                                 "else " \
 156                                         "echo ERROR: Cannot load the DT; " \
 157                                         "exit; " \
 158                                 "fi; " \
 159                         "fi; " \
 160                 "else " \
 161                         "bootm; " \
 162                 "fi;\0"
 163
 164 #define CONFIG_BOOTCOMMAND \
 165         "mmc dev ${mmcdev}; if mmc rescan; then " \
 166                 "if run loadbootscript; then " \
 167                         "run bootscript; " \
 168                 "else " \
 169                         "if run loaduimage; then " \
 170                                 "run mmcboot; " \
 171                         "else run netboot; " \
 172                         "fi; " \
 173                 "fi; " \
 174         "else run netboot; fi"
 175
 176 #define CONFIG_ARP_TIMEOUT      200UL
 177
 178 /* Miscellaneous configurable options */
 179 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 180 #define CONFIG_SYS_HUSH_PARSER          /* use "hush" command parser */
 181 #define CONFIG_SYS_PROMPT               "MX53LOCO U-Boot > "
 182 #define CONFIG_AUTO_COMPLETE
 183 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 184
 185 /* Print Buffer Size */
 186 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 187 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 188 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 189
 190 #define CONFIG_SYS_MEMTEST_START       0x70000000
 191 #define CONFIG_SYS_MEMTEST_END         0x70010000
 192
 193 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 194
 195 #define CONFIG_SYS_HZ           1000
 196 #define CONFIG_CMDLINE_EDITING
 197
 198 /* Physical Memory Map */
 199 #define CONFIG_NR_DRAM_BANKS    2
 200 #define PHYS_SDRAM_1            CSD0_BASE_ADDR
 201 #define PHYS_SDRAM_1_SIZE       (512 * 1024 * 1024)
 202 #define PHYS_SDRAM_2            CSD1_BASE_ADDR
 203 #define PHYS_SDRAM_2_SIZE       (512 * 1024 * 1024)
 204 #define PHYS_SDRAM_SIZE         (PHYS_SDRAM_1_SIZE + PHYS_SDRAM_2_SIZE)
 205
 206 #define CONFIG_SYS_SDRAM_BASE           (PHYS_SDRAM_1)
 207 #define CONFIG_SYS_INIT_RAM_ADDR        (IRAM_BASE_ADDR)
 208 #define CONFIG_SYS_INIT_RAM_SIZE        (IRAM_SIZE)
 209
 210 #define CONFIG_SYS_INIT_SP_OFFSET \
 211         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 212 #define CONFIG_SYS_INIT_SP_ADDR \
 213         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 214
 215 /* FLASH and environment organization */
 216 #define CONFIG_SYS_NO_FLASH
 217
 218 #define CONFIG_ENV_OFFSET      (6 * 64 * 1024)
 219 #define CONFIG_ENV_SIZE        (8 * 1024)
 220 #define CONFIG_ENV_IS_IN_MMC
 221 #define CONFIG_SYS_MMC_ENV_DEV 0
 222
 223 #define CONFIG_OF_LIBFDT
 224
 225 #define CONFIG_CMD_SATA
 226 #ifdef CONFIG_CMD_SATA
 227         #define CONFIG_DWC_AHSATA
 228         #define CONFIG_SYS_SATA_MAX_DEVICE      1
 229         #define CONFIG_DWC_AHSATA_PORT_ID       0
 230         #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_BASE_ADDR
 231         #define CONFIG_LBA48
 232         #define CONFIG_LIBATA
 233 #endif
 234
 235 /* Framebuffer and LCD */
 236 #define CONFIG_PREBOOT
 237 #define CONFIG_VIDEO
 238 #define CONFIG_VIDEO_IPUV3
 239 #define CONFIG_CFB_CONSOLE
 240 #define CONFIG_VGA_AS_SINGLE_DEVICE
 241 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 242 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 243 #define CONFIG_VIDEO_BMP_RLE8
 244 #define CONFIG_SPLASH_SCREEN
 245 #define CONFIG_BMP_16BPP
 246 #define CONFIG_VIDEO_LOGO
 247 #define CONFIG_IPUV3_CLK        200000000
 248
 249 #endif                          /* __CONFIG_H */