include/configs/mx6cuboxi.h

   1 /*
   2  * Copyright (C) 2015 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the SolidRun mx6 based boards
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8 #ifndef __MX6CUBOXI_CONFIG_H
   9 #define __MX6CUBOXI_CONFIG_H
  10
  11 #include <config_distro_defaults.h>
  12 #include "mx6_common.h"
  13
  14 #include "imx6_spl.h"
  15
  16 #define CONFIG_IMX_THERMAL
  17
  18 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  19 #define CONFIG_MXC_UART
  20
  21 /* MMC Configs */
  22 #define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC2_BASE_ADDR
  23
  24 /* SATA Configuration */
  25 #ifdef CONFIG_CMD_SATA
  26 #define CONFIG_DWC_AHSATA
  27 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  28 #define CONFIG_DWC_AHSATA_PORT_ID       0
  29 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  30 #define CONFIG_LBA48
  31 #define CONFIG_LIBATA
  32 #endif
  33
  34 /* Ethernet Configuration */
  35 #define CONFIG_FEC_MXC
  36 #define CONFIG_MII
  37 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  38 #define CONFIG_FEC_XCV_TYPE             RGMII
  39 #define CONFIG_FEC_MXC_PHYADDR          0
  40 #define CONFIG_PHY_ATHEROS
  41
  42 /* Framebuffer */
  43 #define CONFIG_VIDEO_IPUV3
  44 #define CONFIG_IPUV3_CLK                260000000
  45 #define CONFIG_VIDEO_BMP_RLE8
  46 #define CONFIG_SPLASH_SCREEN
  47 #define CONFIG_SPLASH_SCREEN_ALIGN
  48 #define CONFIG_BMP_16BPP
  49 #define CONFIG_VIDEO_LOGO
  50 #define CONFIG_VIDEO_BMP_LOGO
  51 #define CONFIG_IMX_HDMI
  52 #define CONFIG_IMX_VIDEO_SKIP
  53
  54 /* USB */
  55 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  56 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  57 #define CONFIG_MXC_USB_FLAGS            0
  58 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  59 #define CONFIG_PREBOOT \
  60         "if hdmidet; then " \
  61                 "usb start; "                  \
  62                 "setenv stdin  serial,usbkbd; "\
  63                 "setenv stdout serial,vga; "   \
  64                 "setenv stderr serial,vga; "   \
  65         "else " \
  66                 "setenv stdin  serial; " \
  67                 "setenv stdout serial; " \
  68                 "setenv stderr serial; " \
  69         "fi;"
  70
  71 /* Command definition */
  72
  73 #define CONFIG_MXC_UART_BASE    UART1_BASE
  74 #define CONSOLE_DEV     "ttymxc0"
  75 #define CONFIG_SYS_FSL_USDHC_NUM        1
  76 #define CONFIG_SYS_MMC_ENV_DEV          0       /* SDHC2 */
  77
  78 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  79 #ifndef CONFIG_SPL_BUILD
  80 #define CONFIG_EXTRA_ENV_SETTINGS \
  81         "fdtfile=undefined\0" \
  82         "fdt_addr_r=0x18000000\0" \
  83         "fdt_addr=0x18000000\0" \
  84         "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0"  \
  85         "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
  86         "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
  87         "ramdisk_addr_r=0x13000000\0" \
  88         "ramdiskaddr=0x13000000\0" \
  89         "initrd_high=0xffffffff\0" \
  90         "fdt_high=0xffffffff\0" \
  91         "ip_dyn=yes\0" \
  92         "console=" CONSOLE_DEV ",115200\0" \
  93         "bootm_size=0x10000000\0" \
  94         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
  95         "finduuid=part uuid mmc 0:1 uuid\0" \
  96         "update_sd_firmware=" \
  97                 "if test ${ip_dyn} = yes; then " \
  98                         "setenv get_cmd dhcp; " \
  99                 "else " \
 100                         "setenv get_cmd tftp; " \
 101                 "fi; " \
 102                 "if mmc dev ${mmcdev}; then "   \
 103                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 104                                 "setexpr fw_sz ${filesize} / 0x200; " \
 105                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 106                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 107                         "fi; "  \
 108                 "fi\0" \
 109         "findfdt="\
 110                 "if test $board_name = HUMMINGBOARD && test $board_rev = MX6Q ; then " \
 111                         "setenv fdtfile imx6q-hummingboard.dtb; fi; " \
 112                 "if test $board_name = HUMMINGBOARD && test $board_rev = MX6DL ; then " \
 113                         "setenv fdtfile imx6dl-hummingboard.dtb; fi; " \
 114                 "if test $board_name = CUBOXI && test $board_rev = MX6Q ; then " \
 115                         "setenv fdtfile imx6q-cubox-i.dtb; fi; " \
 116                 "if test $board_name = CUBOXI && test $board_rev = MX6DL ; then " \
 117                         "setenv fdtfile imx6dl-cubox-i.dtb; fi; " \
 118                 "if test $fdtfile = undefined; then " \
 119                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 120         BOOTENV
 121
 122 #define CONFIG_BOOTCOMMAND \
 123         "run findfdt; " \
 124         "run finduuid; " \
 125         "run distro_bootcmd"
 126
 127 #define BOOT_TARGET_DEVICES(func) \
 128         func(MMC, mmc, 0) \
 129         func(SATA, sata, 0) \
 130         func(USB, usb, 0) \
 131         func(PXE, pxe, na) \
 132         func(DHCP, dhcp, na)
 133
 134 #include <config_distro_bootcmd.h>
 135
 136 #else
 137 #define CONFIG_EXTRA_ENV_SETTINGS
 138 #endif /* CONFIG_SPL_BUILD */
 139
 140 /* Physical Memory Map */
 141 #define CONFIG_NR_DRAM_BANKS           1
 142 #define CONFIG_SYS_SDRAM_BASE          MMDC0_ARB_BASE_ADDR
 143 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 144 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 145
 146 #define CONFIG_SYS_INIT_SP_OFFSET \
 147         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 148 #define CONFIG_SYS_INIT_SP_ADDR \
 149         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 150
 151 /* Environment organization */
 152 #define CONFIG_ENV_SIZE                 (8 * 1024)
 153 #define CONFIG_ENV_OFFSET               (8 * 64 * 1024)
 154
 155 #endif                         /* __MX6CUBOXI_CONFIG_H */