include/configs/mx6sabre_common.h

   1 /*
   2  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Freescale i.MX6Q SabreSD board.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __MX6QSABRE_COMMON_CONFIG_H
  10 #define __MX6QSABRE_COMMON_CONFIG_H
  11
  12 #include "mx6_common.h"
  13
  14 #define CONFIG_IMX6_THERMAL
  15
  16 /* Size of malloc() pool */
  17 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  18
  19 #define CONFIG_BOARD_EARLY_INIT_F
  20 #define CONFIG_BOARD_LATE_INIT
  21
  22 #define CONFIG_MXC_UART
  23
  24 #define CONFIG_CMD_FUSE
  25 #if defined(CONFIG_CMD_FUSE) || defined(CONFIG_IMX6_THERMAL)
  26 #define CONFIG_MXC_OCOTP
  27 #endif
  28
  29 /* MMC Configs */
  30 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  31
  32 #define CONFIG_CMD_PING
  33 #define CONFIG_CMD_DHCP
  34 #define CONFIG_CMD_MII
  35 #define CONFIG_CMD_NET
  36 #define CONFIG_FEC_MXC
  37 #define CONFIG_MII
  38 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  39 #define CONFIG_FEC_XCV_TYPE             RGMII
  40 #define CONFIG_ETHPRIME                 "FEC"
  41 #define CONFIG_FEC_MXC_PHYADDR          1
  42
  43 #define CONFIG_PHYLIB
  44 #define CONFIG_PHY_ATHEROS
  45
  46 #define CONFIG_CMD_SF
  47 #ifdef CONFIG_CMD_SF
  48 #define CONFIG_SPI_FLASH
  49 #define CONFIG_SPI_FLASH_STMICRO
  50 #define CONFIG_MXC_SPI
  51 #define CONFIG_SF_DEFAULT_BUS           0
  52 #define CONFIG_SF_DEFAULT_CS            0
  53 #define CONFIG_SF_DEFAULT_SPEED         20000000
  54 #define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  55 #endif
  56
  57 /* Command definition */
  58 #define CONFIG_CMD_BMODE
  59
  60 #ifdef CONFIG_SUPPORT_EMMC_BOOT
  61 #define EMMC_ENV \
  62         "emmcdev=2\0" \
  63         "update_emmc_firmware=" \
  64                 "if test ${ip_dyn} = yes; then " \
  65                         "setenv get_cmd dhcp; " \
  66                 "else " \
  67                         "setenv get_cmd tftp; " \
  68                 "fi; " \
  69                 "if ${get_cmd} ${update_sd_firmware_filename}; then " \
  70                         "if mmc dev ${emmcdev} 1; then "        \
  71                                 "setexpr fw_sz ${filesize} / 0x200; " \
  72                                 "setexpr fw_sz ${fw_sz} + 1; "  \
  73                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
  74                         "fi; "  \
  75                 "fi\0"
  76 #else
  77 #define EMMC_ENV ""
  78 #endif
  79
  80 #define CONFIG_EXTRA_ENV_SETTINGS \
  81         "script=boot.scr\0" \
  82         "image=zImage\0" \
  83         "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
  84         "fdt_addr=0x18000000\0" \
  85         "boot_fdt=try\0" \
  86         "ip_dyn=yes\0" \
  87         "console=" CONFIG_CONSOLE_DEV "\0" \
  88         "fdt_high=0xffffffff\0"   \
  89         "initrd_high=0xffffffff\0" \
  90         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
  91         "mmcpart=1\0" \
  92         "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
  93         "update_sd_firmware=" \
  94                 "if test ${ip_dyn} = yes; then " \
  95                         "setenv get_cmd dhcp; " \
  96                 "else " \
  97                         "setenv get_cmd tftp; " \
  98                 "fi; " \
  99                 "if mmc dev ${mmcdev}; then "   \
 100                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 101                                 "setexpr fw_sz ${filesize} / 0x200; " \
 102                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 103                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 104                         "fi; "  \
 105                 "fi\0" \
 106         EMMC_ENV          \
 107         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 108                 "root=${mmcroot}\0" \
 109         "loadbootscript=" \
 110                 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 111         "bootscript=echo Running bootscript from mmc ...; " \
 112                 "source\0" \
 113         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 114         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 115         "mmcboot=echo Booting from mmc ...; " \
 116                 "run mmcargs; " \
 117                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 118                         "if run loadfdt; then " \
 119                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 120                         "else " \
 121                                 "if test ${boot_fdt} = try; then " \
 122                                         "bootz; " \
 123                                 "else " \
 124                                         "echo WARN: Cannot load the DT; " \
 125                                 "fi; " \
 126                         "fi; " \
 127                 "else " \
 128                         "bootz; " \
 129                 "fi;\0" \
 130         "netargs=setenv bootargs console=${console},${baudrate} " \
 131                 "root=/dev/nfs " \
 132                 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 133         "netboot=echo Booting from net ...; " \
 134                 "run netargs; " \
 135                 "if test ${ip_dyn} = yes; then " \
 136                         "setenv get_cmd dhcp; " \
 137                 "else " \
 138                         "setenv get_cmd tftp; " \
 139                 "fi; " \
 140                 "${get_cmd} ${image}; " \
 141                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 142                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 143                                 "bootz ${loadaddr} - ${fdt_addr}; " \
 144                         "else " \
 145                                 "if test ${boot_fdt} = try; then " \
 146                                         "bootz; " \
 147                                 "else " \
 148                                         "echo WARN: Cannot load the DT; " \
 149                                 "fi; " \
 150                         "fi; " \
 151                 "else " \
 152                         "bootz; " \
 153                 "fi;\0"
 154
 155 #define CONFIG_BOOTCOMMAND \
 156         "mmc dev ${mmcdev};" \
 157         "if mmc rescan; then " \
 158                 "if run loadbootscript; then " \
 159                 "run bootscript; " \
 160                 "else " \
 161                         "if run loadimage; then " \
 162                                 "run mmcboot; " \
 163                         "else run netboot; " \
 164                         "fi; " \
 165                 "fi; " \
 166         "else run netboot; fi"
 167
 168 #define CONFIG_ARP_TIMEOUT     200UL
 169
 170 #define CONFIG_SYS_MEMTEST_START       0x10000000
 171 #define CONFIG_SYS_MEMTEST_END         0x10010000
 172 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 173
 174 #define CONFIG_STACKSIZE               (128 * 1024)
 175
 176 /* Physical Memory Map */
 177 #define CONFIG_NR_DRAM_BANKS           1
 178 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 179
 180 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 181 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 182 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 183
 184 #define CONFIG_SYS_INIT_SP_OFFSET \
 185         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 186 #define CONFIG_SYS_INIT_SP_ADDR \
 187         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 188
 189 /* Environment organization */
 190 #define CONFIG_ENV_SIZE                 (8 * 1024)
 191
 192 #define CONFIG_ENV_IS_IN_MMC
 193
 194 #if defined(CONFIG_ENV_IS_IN_MMC)
 195 #define CONFIG_ENV_OFFSET               (8 * 64 * 1024)
 196 #endif
 197
 198 /* Framebuffer */
 199 #define CONFIG_VIDEO
 200 #define CONFIG_VIDEO_IPUV3
 201 #define CONFIG_CFB_CONSOLE
 202 #define CONFIG_VGA_AS_SINGLE_DEVICE
 203 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 204 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 205 #define CONFIG_VIDEO_BMP_RLE8
 206 #define CONFIG_SPLASH_SCREEN
 207 #define CONFIG_SPLASH_SCREEN_ALIGN
 208 #define CONFIG_BMP_16BPP
 209 #define CONFIG_VIDEO_LOGO
 210 #define CONFIG_VIDEO_BMP_LOGO
 211 #define CONFIG_IPUV3_CLK 260000000
 212 #define CONFIG_IMX_HDMI
 213 #define CONFIG_IMX_VIDEO_SKIP
 214
 215 #ifndef CONFIG_SPL
 216 #define CONFIG_CI_UDC
 217 #define CONFIG_USBD_HS
 218 #define CONFIG_USB_GADGET_DUALSPEED
 219
 220 #define CONFIG_USB_GADGET
 221 #define CONFIG_CMD_USB_MASS_STORAGE
 222 #define CONFIG_USB_GADGET_MASS_STORAGE
 223 #define CONFIG_USBDOWNLOAD_GADGET
 224 #define CONFIG_USB_GADGET_VBUS_DRAW     2
 225
 226 #define CONFIG_G_DNL_VENDOR_NUM         0x0525
 227 #define CONFIG_G_DNL_PRODUCT_NUM        0xa4a5
 228 #define CONFIG_G_DNL_MANUFACTURER       "FSL"
 229 #endif
 230
 231 #endif                         /* __MX6QSABRE_COMMON_CONFIG_H */