include/configs/mx6sabreauto.h

   1 /*
   2  * Copyright (C) 2012 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Freescale i.MX6Q SabreAuto board.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __MX6SABREAUTO_CONFIG_H
  10 #define __MX6SABREAUTO_CONFIG_H
  11
  12 #ifdef CONFIG_SPL
  13 #include "imx6_spl.h"
  14 #endif
  15
  16 #define CONFIG_MACH_TYPE        3529
  17 #define CONFIG_MXC_UART_BASE    UART4_BASE
  18 #define CONSOLE_DEV             "ttymxc3"
  19
  20 /* USB Configs */
  21 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  22 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
  23 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  24 #define CONFIG_MXC_USB_FLAGS    0
  25
  26 #define CONFIG_PCA953X
  27 #define CONFIG_SYS_I2C_PCA953X_WIDTH    { {0x30, 8}, {0x32, 8}, {0x34, 8} }
  28
  29 #include "mx6sabre_common.h"
  30
  31 /* Falcon Mode */
  32 #ifdef CONFIG_SPL_OS_BOOT
  33 #define CONFIG_SPL_FS_LOAD_ARGS_NAME    "args"
  34 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME  "uImage"
  35 #define CONFIG_SYS_SPL_ARGS_ADDR       0x18000000
  36
  37 /* Falcon Mode - MMC support: args@1MB kernel@2MB */
  38 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR  0x800   /* 1MB */
  39 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
  40 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR        0x1000  /* 2MB */
  41 #endif
  42
  43 #ifdef CONFIG_MTD_NOR_FLASH
  44 #define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
  45 #define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
  46 #define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
  47 #define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
  48 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
  49 #define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
  50 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
  51 #define CONFIG_SYS_FLASH_EMPTY_INFO
  52 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT
  53 #endif
  54
  55 #define CONFIG_SYS_FSL_USDHC_NUM        2
  56 #if defined(CONFIG_ENV_IS_IN_MMC)
  57 #define CONFIG_SYS_MMC_ENV_DEV          0
  58 #endif
  59
  60 /* I2C Configs */
  61 #define CONFIG_SYS_I2C
  62 #define CONFIG_SYS_I2C_MXC
  63 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  64 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  65 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  66 #define CONFIG_SYS_I2C_SPEED            100000
  67
  68 /* NAND stuff */
  69 #define CONFIG_SYS_MAX_NAND_DEVICE     1
  70 #define CONFIG_SYS_NAND_BASE           0x40000000
  71 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  72 #define CONFIG_SYS_NAND_ONFI_DETECTION
  73
  74 /* DMA stuff, needed for GPMI/MXS NAND support */
  75
  76 /* PMIC */
  77 #define CONFIG_POWER
  78 #define CONFIG_POWER_I2C
  79 #define CONFIG_POWER_PFUZE100
  80 #define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
  81
  82 #endif                         /* __MX6SABREAUTO_CONFIG_H */