include/configs/nitrogen6x.h

   1 /*
   2  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Boundary Devices Nitrogen6X
   5  * and Freescale i.MX6Q Sabre Lite boards.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #include "mx6_common.h"
  14
  15 #define CONFIG_MACH_TYPE        3769
  16
  17 /* Size of malloc() pool */
  18 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  19
  20 #define CONFIG_BOARD_EARLY_INIT_F
  21 #define CONFIG_MISC_INIT_R
  22 #define CONFIG_USBD_HS
  23 #define CONFIG_USB_ETHER
  24 #define CONFIG_USB_ETH_CDC
  25 #define CONFIG_NETCONSOLE
  26
  27 #define CONFIG_MXC_UART
  28 #define CONFIG_MXC_UART_BASE           UART2_BASE
  29
  30 #ifdef CONFIG_CMD_SF
  31 #define CONFIG_MXC_SPI
  32 #define CONFIG_SF_DEFAULT_BUS  0
  33 #define CONFIG_SF_DEFAULT_CS   0
  34 #define CONFIG_SF_DEFAULT_SPEED 25000000
  35 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
  36 #endif
  37
  38 /* I2C Configs */
  39 #define CONFIG_SYS_I2C
  40 #define CONFIG_SYS_I2C_MXC
  41 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  42 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  43 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  44 #define CONFIG_SYS_I2C_SPEED            100000
  45 #define CONFIG_I2C_EDID
  46
  47 /* MMC Configs */
  48 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  49 #define CONFIG_SYS_FSL_USDHC_NUM       2
  50
  51 #ifdef CONFIG_MX6Q
  52 #define CONFIG_CMD_SATA
  53 #endif
  54
  55 /*
  56  * SATA Configs
  57  */
  58 #ifdef CONFIG_CMD_SATA
  59 #define CONFIG_DWC_AHSATA
  60 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  61 #define CONFIG_DWC_AHSATA_PORT_ID       0
  62 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  63 #define CONFIG_LBA48
  64 #define CONFIG_LIBATA
  65 #endif
  66
  67 #define CONFIG_FEC_MXC
  68 #define CONFIG_MII
  69 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  70 #define CONFIG_FEC_XCV_TYPE             RGMII
  71 #define CONFIG_ETHPRIME                 "FEC"
  72 #define CONFIG_FEC_MXC_PHYADDR          6
  73 #define CONFIG_PHYLIB
  74 #define CONFIG_PHY_MICREL
  75 #define CONFIG_PHY_MICREL_KSZ9021
  76
  77 /* USB Configs */
  78 #define CONFIG_USB_EHCI
  79 #define CONFIG_USB_EHCI_MX6
  80 #define CONFIG_USB_HOST_ETHER
  81 #define CONFIG_USB_ETHER_ASIX
  82 #define CONFIG_USB_ETHER_MCS7830
  83 #define CONFIG_USB_ETHER_SMSC95XX
  84 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  85 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
  86 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  87 #define CONFIG_MXC_USB_FLAGS    0
  88 #define CONFIG_USB_KEYBOARD
  89 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  90
  91 /* Miscellaneous commands */
  92 #define CONFIG_CMD_BMODE
  93
  94 /* Framebuffer and LCD */
  95 #define CONFIG_VIDEO_IPUV3
  96 #define CONFIG_VGA_AS_SINGLE_DEVICE
  97 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
  98 #define CONFIG_VIDEO_BMP_RLE8
  99 #define CONFIG_SPLASH_SCREEN
 100 #define CONFIG_SPLASH_SCREEN_ALIGN
 101 #define CONFIG_VIDEO_BMP_GZIP
 102 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (6 * 1024 * 1024)
 103 #define CONFIG_BMP_16BPP
 104 #define CONFIG_IPUV3_CLK 260000000
 105 #define CONFIG_CMD_HDMIDETECT
 106 #define CONFIG_IMX_HDMI
 107 #define CONFIG_IMX_VIDEO_SKIP
 108
 109 #define CONFIG_PREBOOT                 ""
 110
 111 #ifdef CONFIG_CMD_SATA
 112 #define CONFIG_DRIVE_SATA "sata "
 113 #else
 114 #define CONFIG_DRIVE_SATA
 115 #endif
 116
 117 #ifdef CONFIG_CMD_MMC
 118 #define CONFIG_DRIVE_MMC "mmc "
 119 #else
 120 #define CONFIG_DRIVE_MMC
 121 #endif
 122
 123 #ifdef CONFIG_USB_STORAGE
 124 #define CONFIG_DRIVE_USB "usb "
 125 #else
 126 #define CONFIG_DRIVE_USB
 127 #endif
 128
 129 #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC CONFIG_DRIVE_USB
 130 #define CONFIG_UMSDEVS CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC
 131
 132 #if defined(CONFIG_SABRELITE)
 133 #define CONFIG_EXTRA_ENV_SETTINGS \
 134         "script=boot.scr\0" \
 135         "uimage=uImage\0" \
 136         "console=ttymxc1\0" \
 137         "fdt_high=0xffffffff\0" \
 138         "initrd_high=0xffffffff\0" \
 139         "fdt_file=imx6q-sabrelite.dtb\0" \
 140         "fdt_addr=0x18000000\0" \
 141         "boot_fdt=try\0" \
 142         "ip_dyn=yes\0" \
 143         "mmcdevs=0 1\0" \
 144         "mmcpart=1\0" \
 145         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
 146         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 147                 "root=${mmcroot}\0" \
 148         "loadbootscript=" \
 149                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 150         "bootscript=echo Running bootscript from mmc ...; " \
 151                 "source\0" \
 152         "loaduimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
 153         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 154         "mmcboot=echo Booting from mmc ...; " \
 155                 "run mmcargs; " \
 156                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 157                         "if run loadfdt; then " \
 158                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 159                         "else " \
 160                                 "if test ${boot_fdt} = try; then " \
 161                                         "bootm; " \
 162                                 "else " \
 163                                         "echo WARN: Cannot load the DT; " \
 164                                 "fi; " \
 165                         "fi; " \
 166                 "else " \
 167                         "bootm; " \
 168                 "fi;\0" \
 169         "netargs=setenv bootargs console=${console},${baudrate} " \
 170                 "root=/dev/nfs " \
 171         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 172                 "netboot=echo Booting from net ...; " \
 173                 "run netargs; " \
 174                 "if test ${ip_dyn} = yes; then " \
 175                         "setenv get_cmd dhcp; " \
 176                 "else " \
 177                         "setenv get_cmd tftp; " \
 178                 "fi; " \
 179                 "${get_cmd} ${uimage}; " \
 180                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 181                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 182                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 183                         "else " \
 184                                 "if test ${boot_fdt} = try; then " \
 185                                         "bootm; " \
 186                                 "else " \
 187                                         "echo WARN: Cannot load the DT; " \
 188                                 "fi; " \
 189                         "fi; " \
 190                 "else " \
 191                         "bootm; " \
 192                 "fi;\0"
 193
 194 #define CONFIG_BOOTCOMMAND \
 195         "for mmcdev in ${mmcdevs}; do " \
 196                 "mmc dev ${mmcdev}; " \
 197                 "if mmc rescan; then " \
 198                         "if run loadbootscript; then " \
 199                                 "run bootscript; " \
 200                         "else " \
 201                                 "if run loaduimage; then " \
 202                                         "run mmcboot; " \
 203                                 "fi; " \
 204                         "fi; " \
 205                 "fi; " \
 206         "done; " \
 207         "run netboot; "
 208 #else
 209 #define CONFIG_EXTRA_ENV_SETTINGS \
 210         "bootdevs=" CONFIG_DRIVE_TYPES "\0" \
 211         "umsdevs=" CONFIG_UMSDEVS "\0" \
 212         "console=ttymxc1\0" \
 213         "clearenv=if sf probe || sf probe || sf probe 1 ; then " \
 214                 "sf erase 0xc0000 0x2000 && " \
 215                 "echo restored environment to factory default ; fi\0" \
 216         "bootcmd=for dtype in ${bootdevs}" \
 217                 "; do " \
 218                         "if itest.s \"xusb\" == \"x${dtype}\" ; then " \
 219                                 "usb start ;" \
 220                         "fi; " \
 221                         "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 222                                 "load " \
 223                                         "${dtype} ${disk}:1 " \
 224                                         "10008000 " \
 225                                         "/6x_bootscript" \
 226                                         "&& source 10008000 ; " \
 227                         "done ; " \
 228                 "done; " \
 229                 "setenv stdout serial,vga ; " \
 230                 "echo ; echo 6x_bootscript not found ; " \
 231                 "echo ; echo serial console at 115200, 8N1 ; echo ; " \
 232                 "echo details at http://boundarydevices.com/6q_bootscript ; " \
 233                 "setenv stdout serial;" \
 234                 "setenv stdin serial,usbkbd;" \
 235                 "for dtype in ${umsdevs} ; do " \
 236                         "if itest.s sata == ${dtype}; then " \
 237                                 "initcmd='sata init' ;" \
 238                         "else " \
 239                                 "initcmd='mmc rescan' ;" \
 240                         "fi; " \
 241                         "for disk in 0 1 ; do " \
 242                                 "if $initcmd && $dtype dev $disk ; then " \
 243                                         "setenv stdout serial,vga; " \
 244                                         "echo expose ${dtype} ${disk} " \
 245                                                 "over USB; " \
 246                                         "ums 0 $dtype $disk ;" \
 247                                 "fi; " \
 248                 "       done; " \
 249                 "done ;" \
 250                 "setenv stdout serial,vga; " \
 251                 "echo no block devices found;" \
 252                 "\0" \
 253         "initrd_high=0xffffffff\0" \
 254         "upgradeu=for dtype in ${bootdevs}" \
 255                 "; do " \
 256                 "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 257                         "load ${dtype} ${disk}:1 10008000 " \
 258                                 "/6x_upgrade " \
 259                                 "&& source 10008000 ; " \
 260                 "done ; " \
 261         "done\0" \
 262
 263 #endif
 264 /* Miscellaneous configurable options */
 265 #define CONFIG_SYS_MEMTEST_START       0x10000000
 266 #define CONFIG_SYS_MEMTEST_END         0x10010000
 267 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 268
 269 /* Physical Memory Map */
 270 #define CONFIG_NR_DRAM_BANKS           1
 271 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 272
 273 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 274 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 275 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 276
 277 #define CONFIG_SYS_INIT_SP_OFFSET \
 278         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 279 #define CONFIG_SYS_INIT_SP_ADDR \
 280         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 281
 282 /* Environment organization */
 283 #define CONFIG_ENV_SIZE                 (8 * 1024)
 284
 285 #if defined(CONFIG_SABRELITE)
 286 #define CONFIG_ENV_IS_IN_MMC
 287 #else
 288 #define CONFIG_ENV_IS_IN_SPI_FLASH
 289 #endif
 290
 291 #if defined(CONFIG_ENV_IS_IN_MMC)
 292 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 293 #define CONFIG_SYS_MMC_ENV_DEV          0
 294 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 295 #define CONFIG_ENV_OFFSET               (768 * 1024)
 296 #define CONFIG_ENV_SECT_SIZE            (8 * 1024)
 297 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 298 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 299 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 300 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 301 #endif
 302
 303 #define CONFIG_CMD_BMP
 304
 305 #define CONFIG_SYS_ALT_MEMTEST
 306
 307 /*
 308  * PCI express
 309  */
 310 #ifdef CONFIG_CMD_PCI
 311 #define CONFIG_PCI
 312 #define CONFIG_PCI_PNP
 313 #define CONFIG_PCI_SCAN_SHOW
 314 #define CONFIG_PCIE_IMX
 315 #endif
 316
 317 #define CONFIG_USB_FUNCTION_MASS_STORAGE
 318
 319 #define CONFIG_USB_FUNCTION_FASTBOOT
 320 #define CONFIG_CMD_FASTBOOT
 321 #define CONFIG_ANDROID_BOOT_IMAGE
 322 #define CONFIG_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
 323 #define CONFIG_FASTBOOT_BUF_SIZE   0x07000000
 324
 325 #endif         /* __CONFIG_H */