include/configs/omap3_beagle.h

   1 /*
   2  * (C) Copyright 2006-2008
   3  * Texas Instruments.
   4  * Richard Woodruff <r-woodruff2@ti.com>
   5  * Syed Mohammed Khasim <x0khasim@ti.com>
   6  *
   7  * Configuration settings for the TI OMAP3530 Beagle board.
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
  16
  17 /*
  18  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  19  * 64 bytes before this address should be set aside for u-boot.img's
  20  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  21  * other needs.  We use this rather than the inherited defines from
  22  * ti_armv7_common.h for backwards compatibility.
  23  */
  24 #define CONFIG_SYS_TEXT_BASE            0x80100000
  25 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
  26 #define CONFIG_SPL_BSS_MAX_SIZE         (512 << 10)     /* 512 KB */
  27 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
  28 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  29
  30 #include <configs/ti_omap3_common.h>
  31
  32 /*
  33  * Display CPU and Board information
  34  */
  35 #define CONFIG_DISPLAY_CPUINFO          1
  36 #define CONFIG_DISPLAY_BOARDINFO        1
  37
  38 #define CONFIG_MISC_INIT_R
  39
  40 #define CONFIG_REVISION_TAG             1
  41 #define CONFIG_ENV_OVERWRITE
  42
  43 /* Status LED */
  44 #define CONFIG_STATUS_LED               1
  45 #define CONFIG_BOARD_SPECIFIC_LED       1
  46 #define STATUS_LED_BIT                  0x01
  47 #define STATUS_LED_STATE                STATUS_LED_ON
  48 #define STATUS_LED_PERIOD               (CONFIG_SYS_HZ / 2)
  49 #define STATUS_LED_BIT1                 0x02
  50 #define STATUS_LED_STATE1               STATUS_LED_ON
  51 #define STATUS_LED_PERIOD1              (CONFIG_SYS_HZ / 2)
  52 #define STATUS_LED_BOOT                 STATUS_LED_BIT
  53 #define STATUS_LED_GREEN                STATUS_LED_BIT1
  54
  55 /* Enable Multi Bus support for I2C */
  56 #define CONFIG_I2C_MULTI_BUS            1
  57
  58 /* Probe all devices */
  59 #define CONFIG_SYS_I2C_NOPROBES         {{0x0, 0x0}}
  60
  61 /* USB */
  62 #define CONFIG_MUSB_GADGET
  63 #define CONFIG_USB_MUSB_OMAP2PLUS
  64 #define CONFIG_MUSB_PIO_ONLY
  65 #define CONFIG_USB_GADGET_DUALSPEED
  66 #define CONFIG_TWL4030_USB              1
  67 #define CONFIG_USB_ETHER
  68 #define CONFIG_USB_ETHER_RNDIS
  69 #define CONFIG_USB_GADGET
  70 #define CONFIG_USB_GADGET_VBUS_DRAW     0
  71 #define CONFIG_USBDOWNLOAD_GADGET
  72 #define CONFIG_G_DNL_VENDOR_NUM         0x0451
  73 #define CONFIG_G_DNL_PRODUCT_NUM        0xd022
  74 #define CONFIG_G_DNL_MANUFACTURER       "TI"
  75 #define CONFIG_CMD_FASTBOOT
  76 #define CONFIG_ANDROID_BOOT_IMAGE
  77 #define CONFIG_USB_FASTBOOT_BUF_ADDR    CONFIG_SYS_LOAD_ADDR
  78 #define CONFIG_USB_FASTBOOT_BUF_SIZE    0x07000000
  79
  80 /* USB EHCI */
  81 #define CONFIG_CMD_USB
  82 #define CONFIG_USB_EHCI
  83
  84 #define CONFIG_USB_EHCI_OMAP
  85 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        147
  86
  87 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
  88 #define CONFIG_USB_HOST_ETHER
  89 #define CONFIG_USB_ETHER_ASIX
  90 #define CONFIG_USB_ETHER_MCS7830
  91 #define CONFIG_USB_ETHER_SMSC95XX
  92
  93 /* GPIO banks */
  94 #define CONFIG_OMAP3_GPIO_5             /* GPIO128..159 is in GPIO bank 5 */
  95 #define CONFIG_OMAP3_GPIO_6             /* GPIO160..191 is in GPIO bank 6 */
  96
  97 /* commands to include */
  98 #include <config_cmd_default.h>
  99
 100 #define CONFIG_CMD_ASKENV
 101
 102 #define CONFIG_CMD_CACHE
 103
 104 #define MTDIDS_DEFAULT                  "nand0=nand"
 105 #define MTDPARTS_DEFAULT                "mtdparts=nand:512k(x-loader),"\
 106                                         "1920k(u-boot),128k(u-boot-env),"\
 107                                         "4m(kernel),-(fs)"
 108
 109 #define CONFIG_USB_STORAGE      /* USB storage support          */
 110 #define CONFIG_CMD_NAND         /* NAND support                 */
 111 #define CONFIG_CMD_LED          /* LED support                  */
 112 #define CONFIG_CMD_SETEXPR      /* Evaluate expressions         */
 113 #define CONFIG_CMD_GPIO     /* Enable gpio command */
 114 #define CONFIG_CMD_DHCP
 115
 116 #define CONFIG_VIDEO_OMAP3      /* DSS Support                  */
 117
 118 /*
 119  * TWL4030
 120  */
 121 #define CONFIG_TWL4030_LED              1
 122
 123 /*
 124  * Board NAND Info.
 125  */
 126 #define CONFIG_SYS_NAND_QUIET_TEST      1
 127 #define CONFIG_NAND_OMAP_GPMC
 128 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of NAND */
 129                                                         /* devices */
 130
 131 #define CONFIG_EXTRA_ENV_SETTINGS \
 132         "loadaddr=0x80200000\0" \
 133         "rdaddr=0x81000000\0" \
 134         "fdt_high=0xffffffff\0" \
 135         "fdtaddr=0x80f80000\0" \
 136         "usbtty=cdc_acm\0" \
 137         "bootfile=uImage\0" \
 138         "ramdisk=ramdisk.gz\0" \
 139         "bootdir=/boot\0" \
 140         "bootpart=0:2\0" \
 141         "console=ttyO2,115200n8\0" \
 142         "mpurate=auto\0" \
 143         "buddy=none\0" \
 144         "optargs=\0" \
 145         "camera=none\0" \
 146         "vram=12M\0" \
 147         "dvimode=640x480MR-16@60\0" \
 148         "defaultdisplay=dvi\0" \
 149         "mmcdev=0\0" \
 150         "mmcroot=/dev/mmcblk0p2 rw\0" \
 151         "mmcrootfstype=ext3 rootwait\0" \
 152         "nandroot=ubi0:rootfs ubi.mtd=4\0" \
 153         "nandrootfstype=ubifs\0" \
 154         "ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
 155         "ramrootfstype=ext2\0" \
 156         "mmcargs=setenv bootargs console=${console} " \
 157                 "${optargs} " \
 158                 "mpurate=${mpurate} " \
 159                 "buddy=${buddy} "\
 160                 "camera=${camera} "\
 161                 "vram=${vram} " \
 162                 "omapfb.mode=dvi:${dvimode} " \
 163                 "omapdss.def_disp=${defaultdisplay} " \
 164                 "root=${mmcroot} " \
 165                 "rootfstype=${mmcrootfstype}\0" \
 166         "nandargs=setenv bootargs console=${console} " \
 167                 "${optargs} " \
 168                 "mpurate=${mpurate} " \
 169                 "buddy=${buddy} "\
 170                 "camera=${camera} "\
 171                 "vram=${vram} " \
 172                 "omapfb.mode=dvi:${dvimode} " \
 173                 "omapdss.def_disp=${defaultdisplay} " \
 174                 "root=${nandroot} " \
 175                 "rootfstype=${nandrootfstype}\0" \
 176         "findfdt=" \
 177                 "if test $beaglerev = AxBx; then " \
 178                         "setenv fdtfile omap3-beagle.dtb; fi; " \
 179                 "if test $beaglerev = Cx; then " \
 180                         "setenv fdtfile omap3-beagle.dtb; fi; " \
 181                 "if test $beaglerev = C4; then " \
 182                         "setenv fdtfile omap3-beagle.dtb; fi; " \
 183                 "if test $beaglerev = xMAB; then " \
 184                         "setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
 185                 "if test $beaglerev = xMC; then " \
 186                         "setenv fdtfile omap3-beagle-xm.dtb; fi; " \
 187                 "if test $fdtfile = undefined; then " \
 188                         "echo WARNING: Could not determine device tree to use; fi; \0" \
 189         "validatefdt=" \
 190                 "if test $beaglerev = xMAB; then " \
 191                         "if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
 192                                 "setenv fdtfile omap3-beagle-xm.dtb; " \
 193                         "fi; " \
 194                 "fi; \0" \
 195         "bootenv=uEnv.txt\0" \
 196         "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
 197         "importbootenv=echo Importing environment from mmc ...; " \
 198                 "env import -t -r $loadaddr $filesize\0" \
 199         "ramargs=setenv bootargs console=${console} " \
 200                 "${optargs} " \
 201                 "mpurate=${mpurate} " \
 202                 "buddy=${buddy} "\
 203                 "vram=${vram} " \
 204                 "omapfb.mode=dvi:${dvimode} " \
 205                 "omapdss.def_disp=${defaultdisplay} " \
 206                 "root=${ramroot} " \
 207                 "rootfstype=${ramrootfstype}\0" \
 208         "loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
 209         "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
 210         "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
 211         "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
 212                 "source ${loadaddr}\0" \
 213         "loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
 214         "mmcboot=echo Booting from mmc ...; " \
 215                 "run mmcargs; " \
 216                 "bootm ${loadaddr}\0" \
 217         "mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
 218                 "run mmcargs; " \
 219                 "bootz ${loadaddr} - ${fdtaddr}\0" \
 220         "nandboot=echo Booting from nand ...; " \
 221                 "run nandargs; " \
 222                 "nand read ${loadaddr} 280000 400000; " \
 223                 "bootm ${loadaddr}\0" \
 224         "ramboot=echo Booting from ramdisk ...; " \
 225                 "run ramargs; " \
 226                 "bootm ${loadaddr}\0" \
 227         "userbutton=if gpio input 173; then run userbutton_xm; " \
 228                 "else run userbutton_nonxm; fi;\0" \
 229         "userbutton_xm=gpio input 4;\0" \
 230         "userbutton_nonxm=gpio input 7;\0"
 231 /* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
 232 #define CONFIG_BOOTCOMMAND \
 233         "run findfdt; " \
 234         "mmc dev ${mmcdev}; if mmc rescan; then " \
 235                 "if run userbutton; then " \
 236                         "setenv bootenv uEnv.txt;" \
 237                 "else " \
 238                         "setenv bootenv user.txt;" \
 239                 "fi;" \
 240                 "echo SD/MMC found on device ${mmcdev};" \
 241                 "if run loadbootenv; then " \
 242                         "echo Loaded environment from ${bootenv};" \
 243                         "run importbootenv;" \
 244                 "fi;" \
 245                 "if test -n $uenvcmd; then " \
 246                         "echo Running uenvcmd ...;" \
 247                         "run uenvcmd;" \
 248                 "fi;" \
 249                 "if run loadbootscript; then " \
 250                         "run bootscript; " \
 251                 "else " \
 252                         "if run loadimage; then " \
 253                                 "run mmcboot;" \
 254                         "fi;" \
 255                 "fi; " \
 256         "fi;" \
 257         "run nandboot;" \
 258         "setenv bootfile zImage;" \
 259         "if run loadimage; then " \
 260                 "run loadfdt;" \
 261                 "run mmcbootz; " \
 262         "fi; " \
 263
 264 /*
 265  * OMAP3 has 12 GP timers, they can be driven by the system clock
 266  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 267  * This rate is divided by a local divisor.
 268  */
 269 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 270
 271 /*-----------------------------------------------------------------------
 272  * FLASH and environment organization
 273  */
 274
 275 /* **** PISMO SUPPORT *** */
 276 #if defined(CONFIG_CMD_NAND)
 277 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 278 #endif
 279
 280 /* Monitor at start of flash */
 281 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 282 #define CONFIG_SYS_ONENAND_BASE         ONENAND_MAP
 283
 284 #define CONFIG_ENV_IS_IN_NAND           1
 285 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB */
 286 #define ONENAND_ENV_OFFSET              0x260000 /* environment starts here */
 287 #define SMNAND_ENV_OFFSET               0x260000 /* environment starts here */
 288
 289 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 290 #define CONFIG_ENV_OFFSET               SMNAND_ENV_OFFSET
 291 #define CONFIG_ENV_ADDR                 SMNAND_ENV_OFFSET
 292
 293 #define CONFIG_OMAP3_SPI
 294
 295 #define CONFIG_SYS_CACHELINE_SIZE       64
 296
 297 /* Defines for SPL */
 298 #define CONFIG_SPL_OMAP3_ID_NAND
 299
 300 /* NAND boot config */
 301 #define CONFIG_SYS_NAND_BUSWIDTH_16BIT  16
 302 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 303 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 304 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 305 #define CONFIG_SYS_NAND_OOBSIZE         64
 306 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
 307 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 308 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9,\
 309                                                 10, 11, 12, 13}
 310 #define CONFIG_SYS_NAND_ECCSIZE         512
 311 #define CONFIG_SYS_NAND_ECCBYTES        3
 312 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
 313 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 314 /* NAND: SPL falcon mode configs */
 315 #ifdef CONFIG_SPL_OS_BOOT
 316 #define CONFIG_CMD_SPL_NAND_OFS         0x240000
 317 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
 318 #define CONFIG_CMD_SPL_WRITE_SIZE       0x2000
 319 #endif
 320
 321 #endif /* __CONFIG_H */