include/configs/omap3_cairo.h

   1 /*
   2  * Configuration settings for the QUIPOS Cairo board.
   3  *
   4  * Copyright (C) DENX GmbH
   5  *
   6  * Author :
   7  *      Albert ARIBAUD <albert.aribaud@3adev.fr>
   8  *
   9  * Derived from EVM  code by
  10  *      Manikandan Pillai <mani.pillai@ti.com>
  11  * Itself derived from Beagle Board and 3430 SDP code by
  12  *      Richard Woodruff <r-woodruff2@ti.com>
  13  *      Syed Mohammed Khasim <khasim@ti.com>
  14  *
  15  * Also derived from include/configs/omap3_beagle.h
  16  *
  17  * SPDX-License-Identifier:     GPL-2.0+
  18  */
  19
  20 #ifndef __OMAP3_CAIRO_CONFIG_H
  21 #define __OMAP3_CAIRO_CONFIG_H
  22
  23 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
  24
  25 /*
  26  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  27  * 64 bytes before this address should be set aside for u-boot.img's
  28  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  29  * other needs.  We use this rather than the inherited defines from
  30  * ti_armv7_common.h for backwards compatibility.
  31  */
  32 #define CONFIG_SYS_TEXT_BASE            0x80100000
  33 #define CONFIG_SYS_UBOOT_START          CONFIG_SYS_TEXT_BASE
  34 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
  35 #define CONFIG_SPL_BSS_MAX_SIZE         (512 << 10)     /* 512 KB */
  36 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
  37 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  38
  39 #define CONFIG_NAND
  40
  41 #include <configs/ti_omap3_common.h>
  42
  43 #define CONFIG_MISC_INIT_R
  44
  45 #define CONFIG_REVISION_TAG             1
  46 #define CONFIG_ENV_OVERWRITE
  47
  48 /* Enable Multi Bus support for I2C */
  49 #define CONFIG_I2C_MULTI_BUS            1
  50
  51 /* Probe all devices */
  52 #define CONFIG_SYS_I2C_NOPROBES         { {0x0, 0x0} }
  53
  54 #define CONFIG_NAND
  55
  56 /* commands to include */
  57 #define CONFIG_CMD_NAND_LOCK_UNLOCK
  58
  59 /*
  60  * TWL4030
  61  */
  62 #define CONFIG_TWL4030_LED              1
  63
  64 /*
  65  * Board NAND Info.
  66  */
  67 #define CONFIG_NAND_OMAP_GPMC
  68 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of NAND */
  69                                                         /* devices */
  70 #define CONFIG_EXTRA_ENV_SETTINGS \
  71         "machid=ffffffff\0" \
  72         "fdt_high=0x87000000\0" \
  73         "baudrate=115200\0" \
  74         "fec_addr=00:50:C2:7E:90:F0\0" \
  75         "netmask=255.255.255.0\0" \
  76         "ipaddr=192.168.2.9\0" \
  77         "gateway=192.168.2.1\0" \
  78         "serverip=192.168.2.10\0" \
  79         "nfshost=192.168.2.10\0" \
  80         "stdin=serial\0" \
  81         "stdout=serial\0" \
  82         "stderr=serial\0" \
  83         "bootargs_mmc_ramdisk=mem=128M " \
  84                 "console=ttyO1,115200n8 " \
  85                 "root=/dev/ram0 rw " \
  86                 "initrd=0x81600000,16M " \
  87                 "mpurate=600 ramdisk_size=16384 omapfb.rotate=1 " \
  88                 "omapfb.rotate_type=1 omap_vout.vid1_static_vrfb_alloc=y\0" \
  89         "mmcboot=mmc init; " \
  90                 "fatload mmc 0 0x80000000 uImage; " \
  91                 "fatload mmc 0 0x81600000 ramdisk.gz; " \
  92                 "setenv bootargs ${bootargs_mmc_ramdisk}; " \
  93                 "bootm 0x80000000\0" \
  94         "bootargs_nfs=mem=99M console=ttyO0,115200n8 noinitrd rw ip=dhcp " \
  95         "root=/dev/nfs " \
  96         "nfsroot=192.168.2.10:/home/spiid/workdir/Quipos/rootfs,nolock " \
  97         "mpurate=600 omapfb.rotate=1 omapfb.rotate_type=1 " \
  98         "omap_vout.vid1_static_vrfb_alloc=y\0" \
  99         "boot_nfs=run get_kernel; setenv bootargs ${bootargs_nfs}; " \
 100         "bootm 0x80000000\0" \
 101         "bootargs_nand=mem=128M console=ttyO1,115200n8 noinitrd " \
 102         "root=/dev/mtdblock4 rw rootfstype=jffs2 mpurate=600 " \
 103         "omap_vout.vid1_static_vrfb_alloc=y omapfb.rotate=1 " \
 104         "omapfb.rotate_type=1\0" \
 105         "boot_nand=nand read.i 0x80000000 280000 300000; setenv " \
 106         "bootargs ${bootargs_nand}; bootm 0x80000000\0" \
 107         "ledorange=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \
 108         "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \
 109         "i2c mw 60 09 10 1; i2c mw 60 06 10 1\0" \
 110         "ledgreen=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \
 111         "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; i2c " \
 112         "mw 60 09 00 1; i2c mw 60 06 10 1\0" \
 113         "ledoff=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \
 114         "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \
 115         "i2c mw 60 09 00 1; i2c mw 60 06 0 1\0" \
 116         "ledred=i2c dev 1; i2c mw 60 00 00 1; i2c mw 60 14 FF 1; " \
 117         "i2c mw 60 15 FF 1; i2c mw 60 16 FF 1; i2c mw 60 17 FF 1; " \
 118         "i2c mw 60 09 10 1; i2c mw 60 06 0 1\0" \
 119         "flash_xloader=mw.b 0x81600000 0xff 0x20000; " \
 120                 "nand erase 0 20000; " \
 121                 "fatload mmc 0 0x81600000 MLO; " \
 122                 "nandecc hw; " \
 123                 "nand write.i 0x81600000 0 20000;\0" \
 124         "flash_uboot=mw.b 0x81600000 0xff 0x40000; " \
 125                 "nand erase 80000 40000; " \
 126                 "fatload mmc 0 0x81600000 u-boot.bin; " \
 127                 "nandecc sw; " \
 128                 "nand write.i 0x81600000 80000 40000;\0" \
 129         "flash_kernel=mw.b 0x81600000 0xff 0x300000; " \
 130                 "nand erase 280000 300000; " \
 131                 "fatload mmc 0 0x81600000 uImage; " \
 132                 "nandecc sw; " \
 133                 "nand write.i 0x81600000 280000 300000;\0" \
 134         "flash_rootfs=fatload mmc 0 0x81600000 rootfs.jffs2; " \
 135                 "nandecc sw; " \
 136                 "nand write.jffs2 0x680000 0xFF ${filesize}; " \
 137                 "nand erase 680000 ${filesize}; " \
 138                 "nand write.jffs2 81600000 680000 ${filesize};\0" \
 139         "flash_scrub=nand scrub; " \
 140                 "run flash_xloader; " \
 141                 "run flash_uboot; " \
 142                 "run flash_kernel; " \
 143                 "run flash_rootfs;\0" \
 144         "flash_all=run ledred; " \
 145                 "nand erase.chip; " \
 146                 "run ledorange; " \
 147                 "run flash_xloader; " \
 148                 "run flash_uboot; " \
 149                 "run flash_kernel; " \
 150                 "run flash_rootfs; " \
 151                 "run ledgreen; " \
 152                 "run boot_nand; \0" \
 153
 154 #define CONFIG_BOOTCOMMAND \
 155         "if fatload mmc 0 0x81600000 MLO; then run flash_all; " \
 156         "else run boot_nand; fi"
 157
 158 /*
 159  * OMAP3 has 12 GP timers, they can be driven by the system clock
 160  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 161  * This rate is divided by a local divisor.
 162  */
 163 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 164
 165 /*-----------------------------------------------------------------------
 166  * FLASH and environment organization
 167  */
 168
 169 /* **** PISMO SUPPORT *** */
 170 #if defined(CONFIG_CMD_NAND)
 171 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 172 #endif
 173
 174 /* Monitor at start of flash */
 175 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 176 #define CONFIG_SYS_ONENAND_BASE         ONENAND_MAP
 177
 178 #define CONFIG_ENV_IS_IN_NAND           1
 179 #define CONFIG_ENV_SIZE                 (128 << 10)     /* 128 KiB */
 180 #define ONENAND_ENV_OFFSET              0x260000 /* environment starts here */
 181 #define SMNAND_ENV_OFFSET               0x260000 /* environment starts here */
 182
 183 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 184 #define CONFIG_ENV_OFFSET               SMNAND_ENV_OFFSET
 185 #define CONFIG_ENV_ADDR                 SMNAND_ENV_OFFSET
 186
 187 #define CONFIG_OMAP3_SPI
 188
 189 /* Defines for SPL */
 190 #define CONFIG_SPL_OMAP3_ID_NAND
 191
 192 /* NAND boot config */
 193 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 194 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 195 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 196 #define CONFIG_SYS_NAND_OOBSIZE         64
 197 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128*1024)
 198 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 199 #define CONFIG_SYS_NAND_ECCPOS          {2, 3, 4, 5, 6, 7, 8, 9,\
 200                                                 10, 11, 12, 13}
 201 #define CONFIG_SYS_NAND_ECCSIZE         512
 202 #define CONFIG_SYS_NAND_ECCBYTES        3
 203 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_HW
 204 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 205 /* NAND: SPL falcon mode configs */
 206 #ifdef CONFIG_SPL_OS_BOOT
 207 #define CONFIG_CMD_SPL_NAND_OFS         0x240000
 208 #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
 209 #define CONFIG_CMD_SPL_WRITE_SIZE       0x2000
 210 #endif
 211
 212 /* env defaults */
 213 #define CONFIG_BOOTFILE                 "uImage"
 214
 215 /* Override OMAP3 common serial console configuration from UART3
 216  * to UART2.
 217  *
 218  * Attention: for UART2, special MUX settings (MUX_DEFAULT(), MCBSP3)
 219  * are needed and peripheral clocks for UART2 must be enabled in
 220  * function per_clocks_enable().
 221  */
 222 #undef CONFIG_CONS_INDEX
 223 #define CONFIG_CONS_INDEX               2
 224 #ifdef CONFIG_SPL_BUILD
 225 #undef CONFIG_SYS_NS16550_COM3
 226 #define CONFIG_SYS_NS16550_COM2         OMAP34XX_UART2
 227 #undef CONFIG_SERIAL3
 228 #define CONFIG_SERIAL2
 229 #endif
 230
 231 /* Provide MACH_TYPE for compatibility with non-DT kernels */
 232 #define MACH_TYPE_OMAP3_CAIRO   3063
 233 #define CONFIG_MACH_TYPE        MACH_TYPE_OMAP3_CAIRO
 234
 235 /*-----------------------------------------------------------------------
 236  * FLASH and environment organization
 237  */
 238
 239 /* **** PISMO SUPPORT *** */
 240
 241 #define CONFIG_SYS_MAX_FLASH_SECT       520     /* max number of sectors */
 242                                                 /* on one chip */
 243 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* max number of flash banks */
 244
 245 /*-----------------------------------------------------------------------
 246  * CFI FLASH driver setup
 247  */
 248 /* timeout values are in ticks */
 249 #define CONFIG_SYS_FLASH_ERASE_TOUT     (100 * CONFIG_SYS_HZ)
 250 #define CONFIG_SYS_FLASH_WRITE_TOUT     (100 * CONFIG_SYS_HZ)
 251
 252 /* Flash banks JFFS2 should use */
 253 #define CONFIG_SYS_MAX_MTD_BANKS        (CONFIG_SYS_MAX_FLASH_BANKS + \
 254                                         CONFIG_SYS_MAX_NAND_DEVICE)
 255 #define CONFIG_SYS_JFFS2_MEM_NAND
 256 /* use flash_info[2] */
 257 #define CONFIG_SYS_JFFS2_FIRST_BANK     CONFIG_SYS_MAX_FLASH_BANKS
 258 #define CONFIG_SYS_JFFS2_NUM_BANKS      1
 259
 260 #endif /* __OMAP3_CAIRO_CONFIG_H */